TVS Diode Arrays (SPATM Family of Products) Lightning Surge Protection - SP4060 Series SP4060 Series 2.5V 20A Rail Diode Array RoHS Pb GREEN The SP4060 integrates low capacitance diodes with an additional zener diode to protect each I/O pin against ESD and high surge events. This robust device can safely absorb up to 20A per IEC61000-4-5 (tp=8/20s) without performance degradation and a minimum 30kV ESD per IEC61000-4-2 International Standard. Their low loading capacitance also makes them ideal for protecting high speed signal pins. Features Pinout I/O 1 I/O 8 I/O 2 I/O 7 I/O 3 I/O 6 I/O 4 I/O 5 t&4% *&$ 30kV contact, 30kV air t-PXDBQBDJUBODFPGQ' (TYP) per I/O t&'5 *&$ " (5/50ns) t-PXMFBLBHFDVSSFOUPG 1A (MAX) at 2.5V t-JHIUOJOH *&$ 20A (8/20s) Applications GND NC I/O 6 I/O 7 t4FU5PQ#PYFT t%FTLUPQT t/PUFCPPLT t(BNF$POTPMFT Functional Block Diagram I/O 8 t-$%1%57T I/O 5 Application Example LVDS Interface LVDS Controller CLK+ CLKA0+ A0- I/O 1 I/O 2 GND I/O 3 Outside World I/O 4 A1+ A1A2+ A2- Signal Shield GND SP4060-08ATG Shield GND Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. (c)2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. 157 Revision: March 20, 2012 SP4060 Series SP4060 Description TVS Diode Arrays (SPATM Family of Products) Lightning Surge Protection - SP4060 Series Thermal Information Absolute Maximum Ratings Symbol Parameter Value Parameter Units Rating Units -65 to 150 C IPP Peak Current (tp=8/20s) 20.0 A Storage Temperature Range PPK Peak Pulse Power (tp=8/20s) 300 W Maximum Junction Temperature 150 C Maximum Lead Temperature (Soldering 20-40s) 260 C TOP Operating Temperature -40 to 85 C TSTOR Storage Temperature -50 to 150 C CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Electrical Characteristics (TOP=25C) Parameter Symbol Reverse Standoff Voltage VRWM Test Conditions Min Typ Max Units 2.5 V Snap Back Voltage VSB ISB=50mA Reverse Leakage Current ILEAK VR=2.5V, I/O to GND 0.5 1.0 A IPP=1A, tp=8/20s, Fwd 4.5 5.5 V IPP=5A, tp=8/20s, Fwd 6.0 7.2 V IPP=10A, tp=8/20s, Fwd 8.0 9.6 V IPP=20A, tp=8/20s, Fwd 12.5 15.0 V Clamp Voltage1 VC ESD Withstand Voltage1 Diode Capacitance VESD 2.0 V IEC61000-4-2 (Contact) 30 kV IEC61000-4-2 (Air) 30 kV 1 CI/O-GND Reverse Bias=0V 4.4 1 CI/O-I/O Reverse Bias=0V 2.2 Diode Capacitance 5.0 pF pF Note: 1. Parameter is guaranteed by design and/or device characterization. Pulse Waveform Clamping Voltage vs. IPP 14.0 110% 100% 12.0 Clamp Voltage (VC) 90% Percent of IPP 80% 70% 60% 50% 40% 10.0 8.0 6.0 4.0 30% 20% 2.0 10% 0.0 0% 0.0 5.0 10.0 15.0 20.0 25.0 1.0 30.0 SP4060 Series 3.0 5.0 7.0 9.0 11.0 13.0 15.0 17.0 19.0 21.0 Peak Pulse Current-IPP (A) Time (s) 158 Revision: March 20, 2012 (c)2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. TVS Diode Arrays (SPATM Family of Products) Lightning Surge Protection - SP4060 Series Capacitance vs. Bias Insertion Loss (S21) I/O to GND 5.0 5 0 4.0 3.0 2.0 SP4060 Attenuation (dB) Capacitance (pF) -5 -10 -15 -20 1.0 -25 -30 0.0 0.0 0.5 1.0 1.5 2.0 10 2.5 100 1000 10000 Frequency (MHz) DC Bias (V) Soldering Parameters Reflow Condition Pb - Free assembly tP TP 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus) Temp (TL) to peak 3C/second max TS(max) to TL - Ramp-up Rate 3C/second max Reflow - Temperature (TL) (Liquidus) 217C - Temperature (tL) 60 - 150 seconds Critical Zone TL to TP Ramp-up Temperature Pre Heat - Temperature Min (Ts(min)) TL TS(max) tL Ramp-do Ramp-down Preheat TS(min) tS 25 time to peak temperature Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 260C Time Package Dimensions -- MSOP10 2.00 [0.0787] D 10 0.50 [0.0197] Package MSOP Pins 10 JEDEC MO-187 E 1.04 [0.0409] 4.24 [0.1669] E1 5.28 [0.2079] 3.20 [0.1260] Millimeters DIM - 1.10 - 0.043 0.15 0.000 0.006 C A1 (c)2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. Max 0.00 Solder Pad Layout e Inches Min A A B Max A1 0.32 [0.0126] 1 2 Min B 0.17 0.27 0.007 0.011 c 0.08 0.23 0.003 0.009 D 2.90 3.10 0.114 0.122 E 4.67 5.10 0.184 0.200 E1 2.90 3.10 0.114 0.122 L 159 Revision: March 20, 2012 SP4060 Series TVS Diode Arrays (SPATM Family of Products) Lightning Surge Protection - SP4060 Series Product Characteristics Part Numbering System SP 4060 - 08 A T G G= Green Silicon Protection Array (SPATM) Family of TVS Diode Arrays Lead Plating Pre-Plated Frame Lead Material Copper Alloy Lead Coplanarity 0.0004 inches (0.102mm) Substitute Material Silicon Body Material Molded Epoxy Flammability UL 94 V-0 T= Tape & Reel Package A = MSOP10 Series Number of Channels Notes : 1. All dimensions are in millimeters Part Marking System 2. Dimensions include solder plating. 3. Dimensions are exclusive of mold flash & metal burr. 4. Blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form. 5. Package surface matte finish VDI 11-13. LF Product Series P = SP4060 YYWWD P*8 YYWW = Date code Number of Channels Assembly Site Ordering Information Part Number Package Marking Min. Order Qty. SP4060-08ATG MSOP10 P*8 4000 Embossed Carrier Tape & Reel Specification -- MSOP-10 Millimetres Inches Min Max Min Max E 1.65 1.85 0.065 0.073 F 5.40 5.60 0.213 0.220 D 1.50 1.60 0.059 0.063 D1 P0 10P0 1.50 Min 3.90 0.059 Min 4.10 40.0+/- 0.20 0.154 0.161 1.574+/-0.008 W 11.90 12.10 0.469 0.476 P 7.90 8.10 0.311 0.319 A0 5.20 5.40 0.205 0.213 B0 3.20 3.40 0.126 0.134 K0 1.20 1.40 0.047 0.055 t 0.30 +/- 0.05 0.012+/- 0.002 Pin 1 Location User Feeding Direction SP4060 Series 160 Revision: March 20, 2012 (c)2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information.