October 2013
3-terminal Filters, SMD Array
For signal line
(UHF band terrestrial digital broadcast / DVB-H band compatible)
MEA-PE series
MEA1210PE 1210[0504 inch]*
MEA1608PE 1608[0603 inch]
MEA2010PE 2010[0804 inch]
* Dimensions Code JIS[EIA]
EMC Components
(2/11)
001-01 / 20131004 / e9621_mea_signal_03.fm
EMC Components
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/11)
001-01 / 20131004 / e9621_mea_signal_03.fm
• All specifications are subject to change without notice.
EMC Components
3-terminal Filters, SMD Array
For signal line
(UHF band terrestrial digital broadcast / DVB-H band compatible)
FEATURES
Single chip for 2-line or 4-line filters, and compatible with high-density mounting.
Compact with a low profile design.
Effective as a desensitization countermeasure in information transmission terminals such as smart phones.
Can be used for signal lines of mobile device displays.
APPLICATION
Noise removal from signal lines of smart phones, digital cameras, PCs, game machines, flat TVs, etc.
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The Storage temperature range is for after the circuit board is mounted.
Overview of the MEA-PE Series
MEA 1210 PE 220 T □□□
Series name L×W×T Dimensions Product internal
code
Capacitance Packaging style Internal code
(mm) (pF)
1210 1.2×1.0×0.5 PE 220 22 T Taping
1608 1.6×0.8×0.5 360 36
2010 2.0×1.0×0.7
Type
Temperature range
Package quantity Individual weight
Operating
temperature
Storage
temperature
（°C） （°C） （pieces/reel） （mg）
MEA1210PE –40 to +85 –40 to +85 4,000 3
MEA1608PE –40 to +85 –40 to +85 4,000 3.5
MEA2010PE –40 to +85 –40 to +85 4,000 7
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/11)
001-01 / 20131004 / e9621_mea_signal_03.fm
• All specifications are subject to change without notice.
EMC Components
Overview of the MEA-PE Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/11)
001-01 / 20131004 / e9621_mea_signal_03.fm
• All specifications are subject to change without notice.
EMC Components
MEA-PE series
MEA1210PE Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
Dimensions in mm
0.65±0.05
1.0±0.15
0.5±0.1
GND
0.35±0.1 0.15min.
0.1min.
1.2±0.15
0.25±0.10.1min.
GND
CH2CH1
Dimensions in mm
0.3
0.65
0.6
0.25
0.9
1.8
0.5
GND
GND
CH1 CH2
(6/11)
001-01 / 20131004 / e9621_mea_signal_03.fm
• All specifications are subject to change without notice.
EMC Components
MEA-PE series MEA1210PE Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
INSERTION LOSS VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Capacitance
(pF)
Cutoff frequency
(MHz)typ.
Insertion loss 20dB
frequency range
(MHz)
Rated voltage
(V)max.
Rated current
(mA)max. Part No.
40 210 470 to 3000 6.3 100 MEA1210PE400T□□□
36 220 470 to 3000 6.3 100 MEA1210PE360T□□□
22 250 470 to 3000 6.3 100 MEA1210PE220T□□□
Measurement item Product No. Manufacturer
Capacitance 4294A Agilent Technologies
Frequency characteristics N5230C Agilent Technologies
Product No. Manufacturer
N5230C Agilent Technologies
10
0
20
30
40
50
70
60
10 100 100001000
400 360
220
Insertion loss (dB)
Frequency (MHz)
(7/11)
001-01 / 20131004 / e9621_mea_signal_03.fm
• All specifications are subject to change without notice.
EMC Components
MEA-PE series
MEA1608PE Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
1.6±0.1
0.8±0.1
0.05min.
0.5±0.1
0.2±0.1
GND GND
0.2±0.1 0.15min.
0.4±0.050.4±0.05 0.4±0.05
CH4CH1 CH2 CH3
Dimensions in mm
0.2 to 0.25
2.0
0.025
0.15
0.5
0.15 to 0.2
0.4 0.04
0.35
0.35
Dimensions in mm
CH2
GND
GND
CH1 CH4CH3
(8/11)
001-01 / 20131004 / e9621_mea_signal_03.fm
• All specifications are subject to change without notice.
EMC Components
MEA-PE series MEA1608PE Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
INSERTION LOSS VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Capacitance
(pF)
Cutoff frequency
(MHz)typ.
Insertion loss 20dB
frequency range
(MHz)
Rated voltage
(V)max.
Rated current
(mA)max. Part No.
36 220 470 to 3000 6.3 100 MEA1608PE360T□□□
27 240 470 to 3000 6.3 100 MEA1608PE270T□□□
22 250 470 to 3000 6.3 100 MEA1608PE220T□□□
15 270 —6.3 100 MEA1608PE150T□□□
Measurement item Product No. Manufacturer
Capacitance 4294A Agilent Technologies
Frequency characteristics N5230C Agilent Technologies
Product No. Manufacturer
N5230C Agilent Technologies
10 100 100001000
0
10
20
30
40
50
60
80
70
360
270
220
150
Insertion loss (dB)
Frequency (MHz)
(9/11)
001-01 / 20131004 / e9621_mea_signal_03.fm
• All specifications are subject to change without notice.
EMC Components
MEA-PE series
MEA2010PE Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
2.0±0.15
1.0±0.15
0.10min.
0.7±0.1
0.25±0.1
GND GND
0.25±0.1 0.15min.
0.5±0.10.5±0.1 0.5±0.1
CH4CH1 CH2 CH3
Dimensions in mm
1.60
2.80
0.25
0.60
1.80
0.25
0.50
Dimensions in mm
CH2
GNDGND
CH1 CH4CH3
(10/11)
001-01 / 20131004 / e9621_mea_signal_03.fm
• All specifications are subject to change without notice.
EMC Components
MEA-PE series MEA2010PE Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
INSERTION LOSS VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Capacitance
(pF)
Cutoff frequency
(MHz)typ.
Insertion loss 20dB
frequency range
(MHz)
Rated voltage
(V)max.
Rated current
(mA)max. Part No.
40 210 470 to 3000 6.3 100 MEA2010PE400T□□□
36 220 470 to 3000 6.3 100 MEA2010PE360T□□□
22 250 470 to 3000 6.3 100 MEA2010PE220T□□□
15 270 -— 6.3 100 MEA2010PE150T□□□
Measurement item Product No. Manufacturer
Capacitance 4294A Agilent Technologies
Frequency characteristics N5230C Agilent Technologies
Product No. Manufacturer
N5230C Agilent Technologies
10
0
20
30
40
50
60
10 100 100001000
Insertion loss (dB)
Frequency (MHz)
400
360 220
150
(11/11)
001-01 / 20131004 / e9621_mea_signal_03.fm
• All specifications are subject to change without notice.
EMC Components
MEA-PE series
Packaging style
REEL DIMENSIONS
TAPE DIMENSIONS
Dimensions in mm
Type A B K t
MEA1210PE
1.20±0.05 1.45±0.05 0.73max.
—
MEA1608PE
1.00±0.10 1.80±0.10 1.0max. 0.25±0.05
MEA2010PE
1.15±0.05 2.15±0.05 1.0max.
—
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
Dimensions in mm
1.0
ø60min.
14.4max.
8.4 +2.0
–0.0
B
A
8.0±0.3
3.5±0.05
1.75±0.1
4.0±0.1
4.0±0.1
2.0±0.05
1.5 +0.1
0
K
MEA1608PEMEA1210PE,
MEA2010PE
t
K
Dimensions in mm