3MTM Four-Wall Header .100" x .100" Latch/Ejector, Straight and Right Angle 3000 Series * Military (with 3M's 3518 & N3518 polarizing key) and centerbump polarization * Optional ejector latches * Mounting holes for securing header to board * Optional polarizing posts available * High temperature insulator option suitable for "no lead" soldering operations * High temperature option suitable for reflow soldering using "paste in hole" techniques * Solder tail option * See Regulatory Information Appendix for chemical compliance information Date Modified: December 3, 2008 TS-0772-H Sheet 1 of 4 Physical Insulator: Material: Glass Filled Polyester (PBT) Glass Filled Polyester (PCT) - (High Temp Option) Flammability: UL 94V-0 Color: Gray (PBT), Beige (PCT), Black (PCT) Contact: Material: Copper Alloy Plating: Underplating: Nickel - Overall (See Ordering Information) Wiping Area: 30 " [ 0.76 m ] Gold Solder Tails: Tin Lead or Matte Tin (See Ordering Information) Marking: 3M Logo, Part Identification Number and Orientation Triangle Electrical Current Rating: 2 A (EIA 364-70) Insulation Resistance: >1 x 109 at 500 VDC Withstanding Voltage: 1000 VRMS at Sea Level Environmental Temperature Rating: -55C to +105C Process Rating: 260C - (High Temp PCT insulator verson), single pass, (profile per J-STD-020C) (PBT insulator version), maximum insulator temperature 191C (solder wave processonly) Moisture Sensitivity Level: 1 (per J-STD-020C) High Temp. (PCT) versions only UL File No.: E68080 3 Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM Four-Wall Header .100" x .100" Latch/Ejector, Straight and Right Angle -X0XX Header without Latch Ejector 3000 Series -X3XX Header with Long Ejector/Latch for 3M Sockets with Strain Relief -X2XX Header with Short Ejector/Latch for 3M Sockets without Strain Relief .68 [17.3] .08 [2.0] .08 [2.0] .573 .010 [ 14.55 ] .424 .010 [ 10.77 ] 1.07 Ref [27.2] .97 Ref [24.6] A .025 .002 Sq Typ [ 0.64 ] .37 Ref [9.4] .46 Ref [11.7] D .24 [6.1] .100 2.54 .020 0.51 .28 7.1 REF. .25 6.4 .30 [7.6] .34 8.6 .13 3.3 Dim. E CL .100 2.54 2X O .100 [2.54] SEE NOTE #2 REF. POSITION #1 B "Y" F Typ Section A-A (Straight) Position 1 Orientation Triangle .025 .002 Sq Typ [ 0.64 ] .24 [6.1] F Typ CL .30 [7.6] "Y" Dim. E .049 Ref [1.24] .100 Ref [2.54] .21 [5.3] Notch A (See Table 1 & Note1) Notch B (See Table 1) Notch C (See Table 1 & Note 1) .16 [4.1] A B .68 [17.3] .12 [3.0] .35 [8.9] .020 [0.51] 2X o .100 [2.54] (See Note 2) A B C .197 [5.00] .20 [5.1] A Section B-B (Right Angle) C 3 Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/ TS-0772-H Sheet 2 of 4 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM Four-Wall Header .100" x .100" Latch/Ejector, Straight and Right Angle 3000 Series Table 1 Dimensions Pin Qty 3M Part Number A B C D Polarizing Notches 10 3793 1.265 (32.13) 1.104 (28.04) 0.865 (21.97) 0.705 (17.91) BC 14 3314 1.465 (37.21) 1.304 (33.12) 1.065 (27.05) 0.905 (22.99) BC 16 3408 1.565 (39.75) 1.404 (35.66) 1.165 (29.59) 1.005 (25.53) ABC Inch (mm) Tolerance Unless Noted .0 Inch 20 3428 1.765 (44.83) 1.604 (40.74) 1.365 (34.67) 1.205 (30.61) ABC 24 3627 1.965 (49.91) 1.804 (45.82) 1.565 (39.75) 1.405 (35.69) ABC 26 3429 2.065 (52.45) 1.904 (48.36) 1.665 (42.29) 1.505 (38.23) ABC 30 3440 2.265 (57.53) 2.104 (53.44) 1.865 (47.37) 1.705 (43.31) ABC 34 3431 2.465 (62.61) 2.304 (58.52) 2.065 (52.45) 1.905 (48.39) ABC 40 3432 2.765 (70.23) 2.604 (66.14) 2.365 (60.07) 2.205 (56.01) ABC 50 3433 3.265 (82.93) 3.104 (78.84) 2.865 (72.77) 2.705 (68.71) ABC 60 3372 3.765 (95.63) 3.604 (91.54) 3.365 (85.47) 3.205 (81.41) ABC 64 3764 3.965 (100.71) 3.804 (96.62) 3.565 (90.55) 3.405 (86.49) ABC .1 .00 .000 .01 .005 [ ] Dimensions for Reference only Table 2 3M Part Number Suffix -5XX2 -6XX2 -5XO3 -6XO3 Contact Tail Dim E Pin Cross Section Dim G Solder Tail for .062 (1.57) Thick PC Board .112 .010 (2.84) Dim F .0245 .0005 (0.622) Diagonals .028 .001 (0.71) Corner Radii .0075 Ref (0.191) 0.035 .003 (0.89) (See Note 3) Solder Tail for 0.94 (2.39) to .125 (3.18) Thick PC Board .155 .010 (3.94) .0245 .0005 (0.622) .028 .001 (0.71) .0075 Ref (0.191) 0.035 .003 (0.89) o.106 or o.116 [2.95] [2.69] or o.116 o.106 [2.69] [2.95] (See Note 2) .300 [7.62] Side to Side Stackability "Y" .41 (See Note 2) [10.4] Max to Edge of PCB Dim G for Daisy Chain Dim G "Y" CL .029 [0.74] Position 1 .060 [1.52] .100 .003 [2.54] .100 .003 [2.54] .352 [8.94] .100 .003 [2.54] CL Position 1 .100 .003 [2.54] .232 [5.89] C B Recommended Mounting Hole Pattern (Straight) Recommended Mounting Hole Pattern (Right Angle) Notes: 1. Notches A & C will accomodate 3M Polarizing Keys (3M Part #3518 or #N3518). 2. Mounting hardware: From solder side of pc board use #4-24 thread cutting screw (3M Part # 3341-5) and .116 [2.95] dia mounting hole. For right angle version only, #2-56 bolt and nut (3M Part # 3341-6) with .106 [2.69] dia mounting hole may be used. 3. The recommended PCB hole size for the kinked tail positions on the .112 solder tail connector is .035 .002. See page 4 for kink position details (K2 version). 4. Contact your 3M sales representative for custom requirements. X3XXX-XXXXXX Ordering Information Blank = Std. Temp Gray (PBT) /(Blank or UB Pltg. Req'd.) N = High Temp Beige (PCT) /(Blank or UB Pltg. Req'd.) N = High Temp Black (PCT)/(RB Plating Req'd) 3M Part Number (See Table 1) Pin Configuration 5 = Right Angle Solder Tails 6 = Straight Solder Tails 3 Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/ Latch/Ejector System 0 = No Latch/Ejector installed 2 = Short Roll Pin Latch/Ejectors 3 = Long Roll Pin Latch/Ejectors 5 = Short, Snap-In Latch/Ejectors 6 = Long, Snap-In Latch/Ejectors Plating RB = 30 " [ 0.76 m ] Gold and 200 " [ 5.08 m ] Matte Tin over 100 " [ 2.54 m ] Nickel (App. E1 & C1 Apply) Blank or UB = 30 " (0.76 m ] Gold and 200 " [ 5.08 m ] Tin Lead over 100 " [ 2.54 m ] Nickel (App. E3 & C2 Apply) Tail 02 = for .062 [1.57] thick board 03 = for .094 to .125 [2.39 to 3.18] thick board K2 = kinked for .062 [1.57] thick board TS-0772-H Sheet 3 of 4 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM Four-Wall Header .100" x .100" Latch/Ejector, Straight and Right Angle 3000 Series Part Customization Polarizing Post This spec sheet details our standard offering. 3M has several capabilities that can provide a part tailored to your specific needs. Ask your 3M sales representative or customer service for more details. .321 [8.15] .100 Dia [2.54] Both snap in and roll pin latches may be ordered separately. Snap in and roll style latches are dimensionally and functionally equivalent. If ordering snap-in or roll pin style latches separately, please use the below chart. Short Latch Long Latch Latch Style Color Standard Temperature (PBT) 3505-2 3505-3 Roll Pin Gray High Temperature (PCT) N3505-2 N3505-3 Roll Pin Beige High Temperature (PCT) N3505-2B N3505-3B Roll Pin Black High Temperature (PPA) 3505-30 3505-31 Snap-In Gray High Temperature (PPA) N3505-30 N3505-31 Snap-In Beige High Temperature (PPA) N3505-30B N3505-31B Snap-In Black * Selective pin removal (ATA or other compatability) * Wire wrap tails styles 3201-3 PBT Gray 3201-4 LCP Black Note: Insert Post into one mounting hardware hole on bottom of header. Set post to protrude .115" [2.92]. 2500 & 3000 Series Shrouded Header Total Number of Pins Number of Tails Kinked 10 4 3 4 14 4 3 16 4 3 20 4 24 4 26 30 Positions Kinked 7 8 4 11 12 4 13 14 3 4 17 18 3 4 21 22 4 3 4 23 24 4 5 6 25 26 34 4 7 8 27 28 36 4 7 8 27 28 40 4 7 8 33 34 50 4 7 8 43 44 60 4 11 12 49 50 64 4 11 12 53 54 Kinked Tail Detail: Kink is located .05" below bottom surface of plastic. External radius of kink toward part centerline. Mounting Hardware 3341-5 (Installed from bottom of board) .50 [12.7] .31 [7.9] Panhead Thread Cutting Screw: #4-24 X 5/16" Type: USA Std BT, Federal BG Polarizing Keys 3341-6 (Must be inserted prior to latch on vertical headers) Hex Head Bolt, Nut and Washer Bolt - #2-56 X 1/2" 3341-5 & 6 Material - Stainless Steel Dim A N3518 LCP Black .02 3518 PBT Gray .02 Breakaway Tab .09 [2.3] .34 Ref [8.6] .15 [3.8] A Note: #2216 B/A Scotchweld can be used to adhere keys. TS-0772-H Sheet 4 of 4 3 Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Regulatory Information Appendix 3M Electronic Solutions Division/Interconnect EUROPE Appendix E1: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below. Appendix E2: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below. Appendix E3: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below. Appendix E4: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC, as amended by EU Commission Decision 2005/717/EC, as amended by EU Court of Justice Decision 2008/C 116/04 This product contains decaBDE in the insulating material in excess of the maximum concentration allowed for finished products subject to EU RoHS that are placed on the EU market after June 30, 2008. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.product Warranty stated below. RIA-2217A-E Appendix E5: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under Item 6 of the Annex to the Directive. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below. CHINA Appendix C1: China RoHS Electronic Industry Standard of the People's Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below. Appendix C2: China RoHS Electronic Industry Standard of the People's Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product's life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the product Warranty stated below. RIA-2217A-E Appendix C3: China RoHS Electronic Industry Standard of the People's Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product's life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the product Warranty stated below. Important Notice All statements, technical information, and recommendations related to 3M's products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M's current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of 90 days from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 3M Electronics Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3m.com/interconnects Please recycle. Printed in USA. (c) 3M 2008. All rights reserved. RIA-2217A-E 3M is a trademark of 3M Company.