ISL9R1560G2, ISL9R1560P2, ISL9R1560S2, ISL9R1560S3S 15A, 600V StealthTM Diode General Description Features * Soft Recovery . . . . . . . . . . . . . . . . . . . . . . . . tb / ta > 1.2 The ISL9R1560G2, ISL9R1560P2, ISL9R1560S2 and ISL9R1560S3S are StealthTM diodes optimized for low loss performance in high frequency hard switched applications. The StealthTM family exhibits low reverse recovery current (IRM(REC)) and exceptionally soft recovery under typical operating conditions. * Fast Recovery . . . . . . . . . . . . . . . . . . . . . . . . . trr < 30ns * Operating Temperature . . . . . . . . . . . . . . . . . . . . 175oC * Reverse Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . 600V * Avalanche Energy Rated This device is intended for use as a free wheeling or boost diode in power supplies and other power switching applications. The low IRM(REC) and short ta phase reduce loss in switching transistors. The soft recovery minimizes ringing, expanding the range of conditions under which the diode may be operated without the use of additional snubber circuitry. Consider using the StealthTM diode with an SMPS IGBT to provide the most efficient and highest power density design at lower cost. Applications * Switch Mode Power Supplies * Hard Switched PFC Boost Diode * UPS Free Wheeling Diode * Motor Drive FWD * SMPS FWD * Snubber Diode Formerly developmental type TA49410. Package Symbol JEDEC TO-220AC JEDEC STYLE TO-247 ANODE K CATHODE CATHODE (BOTTOM SIDE METAL) ANODE CATHODE CATHODE (FLANGE) A JEDEC STYLE TO-262 JEDEC TO-263AB ANODE CATHODE CATHODE (FLANGE) CATHODE (FLANGE) N/C ANODE Device Maximum Ratings TC = 25C unless otherwise noted Symbol VRRM Parameter Repetitive Peak Reverse Voltage Ratings 600 Units V Working Peak Reverse Voltage 600 V DC Blocking Voltage 600 V IF(AV) Average Rectified Forward Current (TC = 145oC) 15 A IFRM Repetitive Peak Surge Current (20kHz Square Wave) 30 A IFSM Nonrepetitive Peak Surge Current (Halfwave 1 Phase 60Hz) 200 A VRWM VR (c)2002 Fairchild Semiconductor Corporation ISL9R1560G2, ISL9R1560P2, ISL9R1560S2, ISL9R1560S3S Rev. C1 ISL9R1560G2, ISL9R1560P2, ISL9R1560S2, ISL9R1560S3S November 2002 EAVL TJ, TSTG TL TPKG Parameter Power Dissipation Avalanche Energy (1A, 40mH) Operating and Storage Temperature Range Maximum Temperature for Soldering Leads at 0.063in (1.6mm) from Case for 10s Package Body for 10s, See Techbrief TB334 Ratings 150 Units W 20 mJ -55 to 175 C 300 260 C C CAUTION: Stresses above those listed in "Device Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Package Marking and Ordering Information Device Marking R1560G2 Device ISL9R1560G2 Package TO-247 Tape Width N/A Quantity 30 R1560P2 ISL9R1560P2 TO-220AC N/A 50 R1560S2 ISL9R1560S2 TO-262 N/A 50 R1560S3S ISL9R1560S3S TO-263AB 24mm 800 Electrical Characteristics TC = 25C unless otherwise noted Symbol Parameter Test Conditions Min Typ Max Units Off State Characteristics IR Instantaneous Reverse Current VR = 600V TC = 25C - - 100 A TC = 125C - - 1.0 mA TC = 25C - 1.8 2.2 V TC = 125C - 1.65 2.0 V - 62 - pF On State Characteristics VF Instantaneous Forward Voltage IF = 15A Dynamic Characteristics CJ Junction Capacitance VR = 10V, IF = 0A Switching Characteristics trr trr IRM(REC) QRR Reverse Recovery Time Reverse Recovery Time Maximum Reverse Recovery Current Reverse Recovered Charge trr Reverse Recovery Time S Softness Factor (tb/ta) IRM(REC) QRR Maximum Reverse Recovery Current Reverse Recovered Charge trr Reverse Recovery Time S Softness Factor (tb/ta) IRM(REC) QRR dIM/dt Maximum Reverse Recovery Current Reverse Recovered Charge IF = 1A, dIF/dt = 100A/s, VR = 30V - 25 30 ns IF = 15A, dIF/dt = 100A/s, VR = 30V - 35 40 ns IF = 15A, dIF/dt = 200A/s, VR = 390V, TC = 25C - 29.4 - ns - 3.5 - A - 57 - nC ns IF = 15A, dIF/dt = 200A/s, VR = 390V, TC = 125C - 90 - - 2.0 - - 5.0 - A - 275 - nC IF = 15A, dIF/dt = 800A/s, VR = 390V, TC = 125C - 52 - ns - 1.36 - - 13.5 - A - 390 - nC - 800 - A/s Maximum di/dt during tb Thermal Characteristics RJC Thermal Resistance Junction to Case - - 1.0 C/W RJA Thermal Resistance Junction to Ambient TO-247 - - 30 C/W RJA Thermal Resistance Junction to Ambient TO-220 - - 62 C/W RJA Thermal Resistance Junction to Ambient TO-262 - - 62 C/W RJA Thermal Resistance Junction to Ambient TO-263 - - 62 C/W (c)2002 Fairchild Semiconductor Corporation ISL9R1560G2, ISL9R1560P2, ISL9R1560S2, ISL9R1560S3S Rev. C1 ISL9R1560G2, ISL9R1560P2, ISL9R1560S2, ISL9R1560S3S Symbol PD 4000 30 175oC 1000 IR, REVERSE CURRENT (A) IF, FORWARD CURRENT (A) 25 175oC 150oC 20 25oC 125oC 15 100oC 10 150oC 125oC 100 100oC 75oC 10 1 5 25oC 0 0.5 0.75 1.0 1.25 1.5 1.75 2.0 0.1 100 2.25 200 VF, FORWARD VOLTAGE (V) Figure 1. Forward Current vs Forward Voltage 500 600 100 VR = 390V, TJ = 125C 80 VR = 390V, TJ = 125C tb AT IF = 30A, 15A, 7.5A 80 tb AT dIF/dt = 200A/s, 500A/s, 800A/s t, RECOVERY TIMES (ns) t, RECOVERY TIMES (ns) 400 Figure 2. Reverse Current vs Reverse Voltage 100 60 40 20 60 40 20 ta AT dIF/dt = 200A/s, 500A/s, 800A/s ta AT IF = 30A, 15A, 7.5A 0 0 5 10 15 20 25 0 200 30 IF, FORWARD CURRENT (A) dIF/dt = 800A/s 14 12 dIF/dt = 500A/s 10 8 dIF/dt = 200A/s 6 4 2 0 5 10 15 20 25 30 IF, FORWARD CURRENT (A) Figure 5. Maximum Reverse Recovery Current vs Forward Current (c)2002 Fairchild Semiconductor Corporation 600 800 1000 1200 1400 1600 Figure 4. ta and tb Curves vs dIF/dt IRM(REC) , MAX REVERSE RECOVERY CURRENT (A) 16 VR = 390V, TJ = 125C 400 dIF /dt, CURRENT RATE OF CHANGE (A/s) Figure 3. ta and tb Curves vs Forward Current IRM(REC) , MAX REVERSE RECOVERY CURRENT (A) 300 VR , REVERSE VOLTAGE (V) 25 VR = 390V, TJ = 125C IF = 30A 20 IF = 15A 15 IF = 7.5A 10 5 0 200 400 600 800 1000 1200 1400 1600 dIF /dt, CURRENT RATE OF CHANGE (A/s) Figure 6. Maximum Reverse Recovery Current vs dIF/dt ISL9R1560G2, ISL9R1560P2, ISL9R1560S2, ISL9R1560S3S Rev. C1 ISL9R1560G2, ISL9R1560P2, ISL9R1560S2, ISL9R1560S3S Typical Performance Curves QRR, REVERSE RECOVERED CHARGE (nC) S, REVERSE RECOVERY SOFTNESS FACTOR 700 2.5 VR = 390V, TJ = 125C IF = 30A 2.0 IF = 15A 1.5 IF = 7.5A 1.0 0.5 200 400 600 800 1000 1200 1400 VR = 390V, TJ = 125C IF = 30A 600 500 IF = 15A 400 IF = 7.5A 300 200 200 1600 dIF /dt, CURRENT RATE OF CHANGE (A/s) 1000 1200 1400 1600 IF(AV), AVERAGE FORWARD CURRENT (A) 16 1000 800 600 400 200 0 0.1 1 10 12 10 8 6 4 2 0 140 145 150 155 160 165 170 175 TC, CASE TEMPERATURE (oC) Figure 9. Junction Capacitance vs Reverse Voltage 1.0 14 100 VR , REVERSE VOLTAGE (V) THERMAL IMPEDANCE 800 Figure 8. Reverse Recovered Charge vs dIF/dt 1200 CJ , JUNCTION CAPACITANCE (pF) 600 dIF /dt, CURRENT RATE OF CHANGE (A/s) Figure 7. Reverse Recovery Softness Factor vs dIF/dt ZJA, NORMALIZED 400 Figure 10. DC Current Derating Curve DUTY CYCLE - DESCENDING ORDER 0.5 0.2 0.1 0.05 0.02 0.01 PDM 0.1 t1 t2 NOTES: DUTY FACTOR: D = t1/t2 SINGLE PULSE PEAK TJ = PDM x ZJA x RJA + TA 0.01 10-5 10-4 10-3 10-2 10-1 t, RECTANGULAR PULSE DURATION (s) 100 101 Figure 11. Normalized Maximum Transient Thermal Impedance (c)2002 Fairchild Semiconductor Corporation ISL9R1560G2, ISL9R1560P2, ISL9R1560S2, ISL9R1560S3S Rev. C1 ISL9R1560G2, ISL9R1560P2, ISL9R1560S2, ISL9R1560S3S Typical Performance Curves (Continued) VGE AMPLITUDE AND RG CONTROL dIF/dt t1 AND t2 CONTROL IF L IF DUT RG CURRENT SENSE dIF trr dt ta tb 0 + VGE - MOSFET t1 0.25 IRM VDD IRM t2 Figure 12. trr Test Circuit Figure 13. trr Waveforms and Definitions I = 1A L = 40mH R < 0.1 VDD = 50V EAVL = 1/2LI2 [VR(AVL) /(VR(AVL) - VDD)] Q1 = IGBT (BVCES > DUT VR(AVL)) L CURRENT SENSE VAVL R + VDD Q1 VDD DUT IL t0 Figure 14. Avalanche Energy Test Circuit (c)2002 Fairchild Semiconductor Corporation IL I V t1 t2 t Figure 15. Avalanche Current and Voltage Waveforms ISL9R1560G2, ISL9R1560P2, ISL9R1560S2, ISL9R1560S3S Rev. C1 ISL9R1560G2, ISL9R1560P2, ISL9R1560S2, ISL9R1560S3S Test Circuit and Waveforms Typical Performance Curves (Continued) TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACEx FACT ActiveArray FACT Quiet Series Bottomless FASTa CoolFET FASTr CROSSVOLT FRFET DOME GlobalOptoisolator EcoSPARK GTO E2CMOSTM HiSeC EnSignaTM I2C Across the board. Around the world. The Power Franchise Programmable Active Droop ImpliedDisconnect PACMAN POP ISOPLANAR Power247 LittleFET PowerTrencha MicroFET QFET MicroPak QS MICROWIRE QT Optoelectronics MSX Quiet Series MSXPro RapidConfigure OCX RapidConnect OCXPro SILENT SWITCHERa OPTOLOGICa SMART START OPTOPLANAR SPM Stealth SuperSOT-3 SuperSOT-6 SuperSOT-8 SyncFET TinyLogic TruTranslation UHC UltraFETa VCX DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILDS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component is any component of a life 1. Life support devices or systems are devices or support device or system whose failure to perform can systems which, (a) are intended for surgical implant into be reasonably expected to cause the failure of the life the body, or (b) support or sustain life, or (c) whose support device or system, or to affect its safety or failure to perform when properly used in accordance with instructions for use provided in the labeling, can be effectiveness. reasonably expected to result in significant injury to the user. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Rev. I1