UC1710 UC2710 UC3710 High Current FET Driver FEATURES DESCRIPTION * Totem Pole Output with 6A Source/Sink Drive The UC1710 family of FET drivers is made with a high-speed Schottky process to interface between low-level control functions and very high-power switching devices-particularly power MOSFET's. These devices accept low-current digital inputs to activate a high-current, totem pole output which can source or sink a minimum of 6A. * 3ns Delay * 20ns Rise and Fall Time into 2.2nF * 8ns Rise and Fall Time into 30nF * 4.7V to 18V Operation * Inverting and Non-Inverting Outputs * Under-Voltage Lockout with Hysteresis * Thermal Shutdown Protection Supply voltages for both VIN and VC can independently range from 4.7V to 18V. These devices also feature under-voltage lockout with hysteresis. The UC1710 is packaged in an 8-pin hermetically sealed dual in-line package for -55C to +125C operation. The UC2710 and UC3710 are specified for a temperature range of -40C to +85C and 0C to +70C respectively and are available in either an 8-pin plastic dual in-line or a 5-pin, TO-220 package. Surface mount devices are also available. * MINIDIP and Power Packages ORDERING INFORMATION TRUTH TABLE INV N.I. Out H H L OUT= INV and N.I. L H H OUT= INV or N.I. H L L L L L UC1710J UC2710DW UC2710J UC2710N UC2710T UC3710DW UC3710N UC3710T TEMPERATURE RANGE -55C to +125C -40C to +85C 0C to +70C PACKAGE 8 pin CDIP 16 pin SOIC-wide 8 pin CDIP 8 pin PDIP 5 pin TO220 16 pin SOIC-wide 8 pin PDIP 5 pin TO220 BLOCK DIAGRAM INTERNALLY CONNECTED IN T PACKAGE VIN 5 OUTPUT BIAS 4 VC 3 Out 2 Pwr Gnd LOGIC BIAS N.I. IN 8 INV IN 1 Logic Gnd 7 TSD UVLO INTERNALLY CONNECTED IN T PACKAGE UDG-99079 05/99 UC1710 UC2710 UC3710 ABSOLUTE MAXIMUM RATINGS N-Package J-Package T-Package Supply Voltage, Vin . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V Collector Supply Voltage, VC . . . . . . . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18V . . . . . . . . . . . . . . 18V . . . . . . . . . . . . . . 18V Output Current (Source or Sink) Steady-State. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mA. . . . . . . . . . . . 500mA . . . . . . . . . . . . . 1A Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V-VIN . . . . . . . . -0.3V - VIN . . . . . . . . -0.3V - VIN Power Dissipation at Ta=25C . . . . . . . . . . . . . . . . . . . 1W . . . . . . . . . . . . . . . 1W . . . . . . . . . . . . . . . 3W Power Dissipation at T (Case) = 25C. . . . . . . . . . . . . . 2W . . . . . . . . . . . . . . . 2W . . . . . . . . . . . . . . 25W Operating Junction Temperature . . . . . . . -55C to +150C . . . . -55C to +150C . . . . -55C to +150C Storage Temperature . . . . . . . . . . . . . . . -65C to +150C . . . . -65C to +150C . . . . -65C to +150C Lead Temperature (Soldering, 10 seconds) . . . . . . . 300C . . . . . . . . . . . . 300C . . . . . . . . . . . . 300C Note 1: All currents are positive into, negative out of the specified terminal. Note 2: Consult Unitrode Integrated Circuits databook for information regarding thermal specifications and limitations of packages. CONNECTION DIAGRAMS DIL-8 MINIDIP (Top View) J or N Package SOIC-16 (Top View) DW Package 5-Pin TO-220 (Top View) T Package ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for VIN = VC = 15V, No load, TA = TJ. PARAMETERS VIN Supply Current VC Supply Current UVLO Threshold TEST CONDITIONS MIN TYP MAX UNITS VIN =18V, VC =18V, Output Low 26 35 mA VIN =18V, VC =18V, Output High 21 30 mA VIN =18V, VC =18V, Output Low 1.5 5.0 mA VIN =18V, VC =18V,Output High 5.0 8 mA VIN High to Low 3.8 4.1 4.4 V VIN Low to High 4.1 4.4 4.8 V 2 UC1710 UC2710 UC3710 ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for VIN = VC = 15V, No load, TA = TJ. PARAMETERS TEST CONDITIONS UVLO Threshold Hysteresis MIN TYP 0.1 0.3 Digital Input Low Level Digital Input High Level MAX UNITS 0.5 V 0.8 V 2.0 V Digital Input = 0.0V Output High Sat., VC - VO IO= -100mA 1.35 2.2 V IO= -6A 3.2 4.5 V IO= 100mA 0.25 0.6 V IO= 6A 3.4 4.5 V Output Low Sat., VO Thermal Shutdown -70 A Digital Input Current -4.0 165 C From Inv., Input to Output (Note 3, 4): Rise Time Delay 10% to 90% Rise Fall Time Delay 90% to 10% Fall CL = 0 35 70 ns CL = 2.2nF 35 70 ns CL = 30nF 35 70 ns CL = 0 20 40 ns CL = 2.2nF 25 40 ns CL = 30nF 85 150 ns CL = 0 35 70 ns CL = 2.2nF 35 70 ns CL = 30nF 35 80 ns CL = 0 15 40 ns CL = 2.2nF 20 40 ns CL = 30nF 85 150 ns CL = 0 35 70 ns CL = 2.2nF 35 70 ns CL = 30nF 35 70 ns From N.I. Input to Output (Note 3,4): Rise Time Delay 10% to 90% Rise Fall Time Delay 90% to 10% Fall Total Supply Current at 200kHz Input Switching Frequency CL = 0 20 40 ns CL = 2.2nF 25 40 ns CL = 30nF 85 150 ns CL = 0 35 70 ns CL = 2.2nF 35 70 ns CL = 30nF 35 80 ns CL = 0 15 40 ns CL = 2.2nF 20 50 ns CL = 30nF 85 150 ns TA = 25C (Note 5) CL = 0 30 40 mA Note: 3. Delay measured from 50% input change to 10% output change. Note: 4. Those parameters with CL = 30nF are not tested in production. Note: 5. Inv. Input pulsed at 50% duty cycle with N.I. Input = 3V. or N.I. Input pulsed at 50% duty cycle with Inv. Input = 0V. UNITRODE CORPORATION 7 CONTINENTAL BLVD. * MERRIMACK, NH 03054 TEL. (603) 424-2410 FAX (603) 424-3460 3 PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) 5962-0152001QPA ACTIVE CDIP JG 8 1 TBD Call TI 5962-0152001VPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type 5962-0152001VXA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type UC1710J ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type UC1710J883B ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type UC1710L883B OBSOLETE TO/SOT L 20 TBD Call TI Call TI UC1710SP OBSOLETE CDIP J 16 TBD Call TI Call TI UC2710N ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2710NG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2710T ACTIVE TO-220 KC 5 50 Green (RoHS & no Sb/Br) CU SN N / A for Pkg Type UC2710TG3 ACTIVE TO-220 KC 5 50 Green (RoHS & no Sb/Br) CU SN N / A for Pkg Type UC3710DW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3710DWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3710N ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3710NG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3710T ACTIVE TO-220 KC 5 50 Green (RoHS & no Sb/Br) CU SN N / A for Pkg Type UC3710TG3 ACTIVE TO-220 KC 5 50 Green (RoHS & no Sb/Br) CU SN N / A for Pkg Type (1) Call TI The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2011 (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF UC1710, UC1710-SP, UC3710 : * Catalog: UC3710, UC1710 * Military: UC1710 * Space: UC1710-SP NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Military - QML certified for Military and Defense Applications * Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connctivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated