DTR-156-LS-A-ME - Optical Communication Products, Inc.

121737-0252, Rev. A

7-27-2000

DTR-xxx-LC & DTR-xxx-LS

3.3 Volt 2x5 LC connector OC-3 & OC-12 LED Transceivers

Features

Designed for ATM/SONET/SDH OC-3

(156 Mb/s) & OC-12 (622 Mb/s)

Multi-sourced 10-pin (2x5) SFF (Small

Form Factor) package style

Duplex LC optical connector interface

Excellent EMI & ESD protection

- 40°C to +85°C Operating

Temperature (“A” option)

Single +3.3 V supply & LV-PECL

DATA interface

Option for LV-TTL or LV-PECL SIGNAL

DETECT output

The DTR-xxx-LC and DTR-xxx-LS fiber optic

transceivers offer a simple, convenient way to interface

PCBs to multimode fiber optic cables. They are designed

for ATM/SONET/SDH applications at OC-3/STM-1

(156 Mb/s) and OC-12/STM-4 (622 Mb/s).

The transmit and receive functions are contained in a

narrow width two-row, 10-pin (2x5) package with a

Duplex LC connector interface. The receptacle fits into

an RJ-45 form factor outline. The 10-pin configuration

is in conformance to a Small Form Factor (SFF)

multisource transceiver agreement.

The transmitter incorporates a highly reliable 1300 nm

InGaAsP surface-emitting LED and a driver circuit which

converts LV-PECL data to light. A LV-TTL Transmitter

Disable control input is also provided. The receiver

features a transimpedance amplifier IC for high sensitivity

and wide dynamic range. The Receiver Signal Detect

status output can be either LV-TTL or LV-PECL.

The transceiver operates from a single +3.3V power

supply over an operating temperature range of 0°C to

+70°C or - 40°C to +85°C (“A” option). The package is

made of either conductive plastic or metal for excellent

EMI shielding

Description

Optical Communication Products, Inc.

Absolute Maximum Ratings

Parameter Symbol Minimum Maximum Units

Storage Tempera ture Tst - 40 + 85 C

O per at ing Temperat ur e "A" opt ion Top - 40 + 85 C

"blank" option 0 + 70

Supp ly Volta g e VCC 0+ 6.0V

Input Voltage Vin 0VCC V

Outp ut Curre nt IO-50mA

Lead Solder ing Temperature & Time -- 260 C, 10 s ec

OCP

21737-0252, Rev. A

7-27-2000

Transmitter Performance Characteristics (over Operating Case Temperature)

Receiver Performance Characteristics (over Operating Case Temperature)

OC-3/STM-1 LC/LS LED Transceiver: DTR-156-LC/LS

Ordering Information for OC-3/STM-1 applications

M O DULE NAME SIGNAL

DETECT Package

0 C t o 70 C O pera t ing - 40 C to 85 C Operat ing

DTR-156-LC DTR-156-LC-A LV-TTL Plastic

DTR-156-LC-E DTR-156-LC-A-E LV-PECL Plastic

DTR-156-LC-M DTR-156-LC-A-M LV-TTL Metal

DTR-156-LC-ME DTR-156-LC-A-ME LV-PECL Metal

DTR-156-LS DTR-156-LS-A LV-TTL Plastic

DTR-156-LS-E DTR-156-LS-A-E LV-PECL Plastic

DTR-156-LS-M DTR-156-LS-A-M LV-TTL Metal

DTR-156-LS-ME DTR-156-LS-A-ME LV-PECL Metal

Parameter Symbol Minimum Typical Maximum Units

Data Rate BDC 156 266 Mb/s

Optical Output Power 1 Po- 19. 0 - 16. 0 - 14. 0 dBm

Center Wavelength lc1270 - 1380 nm

Spectr al Width (FWHM ) DlFWHM - - 200 nm

Optical Rise and Fall Time (10% to 90%) tr, tf-2.03.0ns

Extinction Ratio Phi / Plo 10 - - dB

Tr ansmitt er O FF Power ( continuous logic LOW input) POFF - - - 45. 0 dBm

Random Jitt er ( peak- t o- peak) RJ - - 0.52 ns

Dut y Cycle Distor t ion ( peak- t o- peak) DCD --0.6ns

Measured average powe r coupl ed into 62.5/125 mm, 0.275 NA graded-index multimode fi ber.

The minimum power specified is at Beginning-of-Life (BOL).

Parameter Symbol Minimum Typical Maximum Units

Data Rate B50 156 266 Mb/s

Re c eiver S ens itivit y ( 2 .5 x 1 0 -10 BER) 1 Pmin - 30. 0 - 33. 0 - dBm

Maximum Input Optical Power (2.5 x 10-10 BER) 1 Pmax - 14. 0 - 12. 0 - dBm

Signal Detect

Thresholds Increasing Light I nput Psd+ - - - 30. 0 dBm

Decreasing Light Input Psd- - 45.0 - -

Signal Detect Hyst er es is - 1. 0 - dB

Signal Detect

Ti m ing Delay I ncreasing Light I nput tsd+ - - 100 ms

Decreasing Light Input tsd- - - 350

Wavelength of Operation l1100 - 1600 nm

1 Specifie d in Average Optical Input Power and mea sured at 156 Mb/ s and 1300 nm w avelength w ith 223- 1 PRBS .

321737-0252, Rev. A

7-27-2000

Transmitter Performance Characteristics (over Operating Case Temperature)

Receiver Performance Characteristics (over Operating Case Temperature)

OC-12/STM-4 LC/LS LED Transceiver: DTR-622-LC/LS

Parameter Symbol Minimum Typical Maximum Units

Data Rate BDC 622 700 Mb/s

Optical Output Power 1 Po- 20. 0 - 18. 0 - 14. 0 dBm

Center Wavelength lc1270 - 1380 nm

Spectr al Width (FWHM ) DlFWHM - 140 200 nm

Optical Rise and Fall Time (10% to 90%) tr, tf- 1.0 1.25 ns

Extinction Ratio Phi / Plo 10 - - dB

Random Jitt er ( peak- t o- peak) RJ - - 0.13 ns

Dut y Cycle Distor t ion ( peak- t o- peak) DCD --0.4ns

Measured average powe r coupl ed into 62.5/125 mm, 0.275 NA graded-index multimode fi ber.

The minimum power specified is at Beginning-of-Life (BOL).

M O DULE NAME SIGNAL

DETECT Package

0 C t o 70 C O pera t ing - 40 C to 85 C Operat ing

DTR-622-LC DTR-622-LC-A LV-TTL Plastic

DTR-622-LC-E DTR-622-LC-A-E LV-PECL Plastic

DTR-622-LC-M DTR-622-LC-A-M LV-TTL Metal

DTR-622-LC-ME DTR-622-LC-A-ME LV-PECL Metal

DTR-622-LS DTR-622-LS-A LV-TTL Plastic

DTR-622-LS-E DTR-622-LS-A-E LV-PECL Plastic

DTR-622-LS-M DTR-622-LS-A-M LV-TTL Metal

DTR-622-LS-ME DTR-622-LS-A-ME LV-PECL Metal

Ordering Information for OC-12/STM-4 applications

Parameter Symbol Minimum Typical Maximum Units

Data Rate B50 622 700 Mb/s

Re c eiver S ens itivit y ( 1 0 -10 BER) 1 Pmin - 26. 0 - 28. 0 - dBm

Maximum Input Optical Power (10-10 BER) 1 Pmax - 14. 0 - 12. 0 - dBm

Signal Detect

Thresholds Increasing Light I nput Psd+ - - - 26. 0 dBm

Decreasing Light Input Psd- - 40.0 - -

Signal Detect Hyst er es is - 1. 0 - dB

Signal Detect

Ti m ing Delay I ncreasing Light I nput tsd+ - - 100 ms

Decreasing Light Input tsd- - - 350

Wavelength of Operation l1100 - 1600 nm

1 Specifie d in Average Optical Input Power and mea sured at 622 Mb/ s and 1300 nm w avelength w ith 223- 1 PRBS .

21737-0252, Rev. A

7-27-2000

Transmitter Electrical Interface (over Operating Case Temperature Range)

Receiver Electrical Interface (over Operating Case Temperature Range)

Electrical Power Supply Characteristics (over Operating Case Temperature Range)

Transmitter: When the DATA+ input is at logic HIGH and

DATA- input is at logic LOW, the LED is ON; and vice versa.

The transmitter is normally enabled (i.e. when the TX

DISABLE control input is not connected). When the TX

DISABLE control input voltage is higher than VCC - 1.3 V, the

LED is turned off independent of the input data.

Receiver: Both differential DATA+ and DATA- outputs are

LV-PECL levels requiring proper termination (see

recommended interface circuits). For optimum performance,

both outputs should be terminated in the same manner, even if

only one is used.

The Signal Detect circuit monitors the level of the incoming

optical signal and generates a logic LOW signal when

insufficient photocurrent is produced. If the SIGNAL DETECT

output is LV-TTL level, no termination is required. If the

SIGNAL DETECT output is LV-PECL level, a termination

resistor of 160 ohms to GND is required.

DTR-

xxx

-LC & DTR-

xxx

-LS

Application Notes

Parameter Symbol Minimum Typical Maximum Units

Supp ly Voltag e VCC 3.13 3.3 3.47 V

Supply Current 1TX ICC,TX - 110 130 mA

RX ICC,RX - 70 100

1 Supply current does not include termination resistor current.

Parameter Symbol Minimum Typical Maximum Units

O ut put HI G H Voltage ( LV-PECL) 1 VOH VCC - 1.10 -VCC - 0.90 V

O ut put LOW Voltage ( LV- PECL) 1 VOL VCC - 1.84 -VCC - 1.60 V

O ut put HI G H Voltage ( LV-TTL) VOH 2.4 - VCC

O utput LO W Voltage ( LV- TTL) VOL 0-0.8

Output C urrent IO--25mA

Wi th 50 ohm ter mi nate d to VCC - 2 volts.

Pin Assignments

PIN FUNCTION LOGIC FAMILY

1RX GND -

CCRX -

3 SD ( RX SIGNAL DETECT) LV-TTL (standard ) or

LV-PECL ("E" o ption)

4 RD- ( RX DATA OUT - ) LV- PECL

5 RD+ (RX DATA OUT + ) LV- PECL

CCTX -

7TX GND -

8 TX DI SABLE LV-T TL

9 TD+ (TX DATA IN +) LV-PECL

10 TD- (TX DATA IN -) LV-PECL

Parameter Symbol Minimum Typical Maximum Units

Input HIGH Voltage VIH VCC - 1. 165 -VCC - 0. 70 V

Input LO W Voltage VIL VCC - 1. 950 -VCC - 1.475 V

Data Input Current - HIGH IH- - 150 mA

Data Input Current - LOW IL0.5 - - mA

Tr ansmitt er Disable Volt age VDIS VCC -1.3 -VCC V

Tr ansmitt er Enable Voltage VEN 0-0.8V

521737-0252, Rev. A

7-27-2000

1 H coil or

fe rr ite in d u c to r

1 H coil or

fe rr ite in d u c to r

TXD+

TXD -

RXD -

RXD+

0.1

0.1 10

0.1

160 160

C a pa citor v alu es in F, R esisto r v alu es in o hm

5 0 oh m lin e

with proper

termination

5 0 oh m lin e

0.022

5 0 oh m lin e

0.022

with proper

termination

Note: If SIGNAL DETECT is LV-PEC L, a termination resistor of 160 ohm to GND is re

uired

TX D ISABLE

SIGNAL DETECT

(see No te b elow)

VCC

+ 3 .3 v o lt

VCC

+ 3 .3 v o lt

chassis

ground

circuit ground

130

82 82

130

MOUNTING

POSTS

1 H coil or

ferrite inductor

1 H coil or

ferrite inductor

TXD+

TXD -

RXD -

RXD+

0.1

0.1 10

0.1

160

100

C a pa cito r va lu es in F, R e sisto r v alu es in o h m

5 0 ohm lin e

LV-PECL

5 0 ohm lin e

100

5 0 ohm lin e

5 0 ohm lin e LV-PECL

Note: If SIGNAL DETECT is LV-PECL, a termination resistor of 160 ohm to GND is required

TX DISABLE

SIGN AL DE T ECT

(s ee N o te b elo w)

VCC

+ 3.3 vo lt

chassis

ground

circuit ground

MOUNTING

POSTS

VCC

+3.3 volt

1 H coil or

fe rri te in d u c to r

TXDATA+

TXD ATA -

RXDATA -

RXDATA+

MOUNTING

POSTS

chassis

ground

circuit ground

0.1 10 0.1

0.1

130

82 82 82 82

130 130 130

C a p ac itor v a lues in F, R e sistor v alu es in o h m

5 0 oh m line

1 H coil or

fe rri te in d u c to r

0.1

TX DISABLE

SIGNAL DETECT

(s ee No te b e lo w)

Note: If SIGN AL DETEC T is LV -PECL, a term ination resistor of 160 ohm to GN D is required

DTR-xxx-LC

DTR-

xxx

-LC & DTR-

xxx

-LS

AC coupling

DC coupling

Interface circuit: Three options for

interface circuit are shown here: two

with DC coupling and one with AC

coupling.

The power supply line should be well-

filtered. All 0.1 mF power supply

bypass capacitors should be as close

to the DTR transceiver module as

possible. The two front GND posts

(mounting studs) should be grounded

to Chassis Ground. If Chassis Ground

is not available, they should be

connected to Circuit Ground.

21737-0252, Rev. A

7-27-2000

Optical Communication Products, Inc. reserves the right to make changes in equipment design or specifications without notice. Information supplied by Optical Communication

Products, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by Optical Communication Products, Inc. for its use nor for any infringements of

third parties which may result from its use. No license is granted by implication or otherwise under any patent right of Optical Communication Products, Inc.

DTR-

xxx

-LC & DTR-

xxx

-LS

Package without

EMI shield (LC)

Dimension in inches

[mm]

Dimension in inches [mm]

Package with

EMI Shield (LS)

Ordering Information

M odule Family EM I Shield SO NET / SDH / Bit rate

DTR-156-LC NO O C-3 / STM -1 / 156 M bps

DTR-622-LC NO O C-12 / STM -4 / 622 M bps

DTR-156-LS Y ES O C-3 / STM -1 / 156 M bps

DTR-622-LS Y ES O C-12 / STM-4 / 622 Mbps

See Ordering Information for each particular module

(Operating Temperature Range, Plastic or Metal

Package, LVTTL or LVPECL SIGNAL DETECT

from Tables on page 2 and 3.

Optical Communication Products, Inc.

20961 Knapp Street, Chatsworth, CA 91311, Tel.: 818-701-0164, FAX: 818-701-1468, http://www.ocp-inc.com