   
   
  
SLOS068P − JUNE 1976 − REVISED SEPTEMBER 2004
1
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
DWide Supply Range:
− Single Supply ...3 V to 32 V
(26 V for LM2904)
− or Dual Supplies . . . +1.5 V to +16 V
(+13 V for LM2904)
DLow Supply-Current Drain, Independent of
Supply Voltage . . . 0.7 mA Typ
DCommon-Mode Input Voltage Range
Includes Ground, Allowing Direct Sensing
Near Ground
DLow Input Bias and Offset Parameters:
− Input Offset Voltage ...3 mV Typ
A Versions ...2 mV Typ
− Input Offset Current ...2 nA Typ
− Input Bias Current . . . 20 nA Typ
A Versions . . . 15 nA Typ
DDifferential Input Voltage Range Equal to
Maximum-Rated Supply Voltage ...32 V
(26 V for LM2904)
DOpen-Loop Differential Voltage
Amplification . . . 100 V/mV Typ
DInternal Frequency Compensation
description/ordering information
These devices consist of two independent,
high-gain, frequency-compensated operational
amplifiers designed to operate from a single
supply over a wide range of voltages. Operation from split supplies also is possible if the difference between
the two supplies is 3 V to 32 V (3 V to 26 V for the LM2904), and VCC is at least 1.5 V more positive than the
input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply
voltage.
Applications include transducer amplifiers, dc amplification blocks, and all the conventional operational
amplifier circuits that now can be implemented more easily in single-supply-voltage systems. For example,
these devices can be operated directly from the standard 5-V supply used in digital systems and easily can
provide the required interface electronics without additional ±5-V supplies.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2004, Texas Instruments Incorporated
  !" # $%&" !#  '%()$!" *!"&+
*%$"# $ " #'&$$!"# '& ",& "&#  &-!# #"%&"#
#"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*&
"&#"0  !)) '!!&"&#+
1
2
3
4
8
7
6
5
1OUT
1IN−
1IN+
GND
VCC
2OUT
2IN−
2IN+
LM158, LM158A ...JG PACKAGE
LM258, LM258A . . . D, DGK, OR P PACKAGE
LM358 . . . D, DGK, P, PS, OR PW PACKAGE
LM358A . . . D, DGK, P, OR PW PACKAGE
LM2904 . . . D, DGK, P, PS, OR PW PACKAGE
(TOP VIEW)
3212019
910111213
4
5
6
7
8
18
17
16
15
14
NC
2OUT
NC
2IN−
NC
NC
1IN−
NC
1IN+
NC
LM158, LM158A . . . FK PACKAGE
(TOP VIEW)
NC
1OUT
NC
NC NC
NC
GND
NC CC+
V
2IN+
NC − No internal connection
 '*%$"# $')!" " 11 !)) '!!&"&# !& "&#"&*
%)&## ",&.#& "&*+  !)) ",& '*%$"# '*%$"
'$&##0 *&# " &$&##!)/ $)%*& "&#"0  !)) '!!&"&#+
   
   
  
SLOS068P − JUNE 1976 − REVISED SEPTEMBER 2004
2POST OFFICE BOX 655303 DALLAS, TEXAS 75265
description/ordering information (continued)
ORDERING INFORMATION
TAVIOmax
AT 25°C
MAX
TESTED
VCC PACKAGEORDERABLE
PART NUMBER TOP-SIDE
MARKING
PDIP (P) Tube of 50 LM358P LM358P
SOIC (D)
Tube of 75 LM358D
LM358
SOIC (D) Reel of 2500 LM358DR LM358
7 mV 30 V SOP (PS) Reel of 2000 LM358PSR L358
7 mV
30 V
TSSOP (PW)
Tube of 150 LM358PW
L358
TSSOP (PW) Reel of 2000 LM358PWR L358
0°C to 70°CMSOP/VSSOP (DGK) Reel of 2500 LM358DGKR M5_
0C to 70 C
PDIP (P) Tube of 50 LM358AP LM358AP
SOIC (D)
Tube of 75 LM358AD
LM358A
3 mV
30 V
SOIC (D) Reel of 2500 LM358ADR LM358A
3 mV 30 V
TSSOP (PW)
Tube of 150 LM358APW
L358A
TSSOP (PW) Reel of 2000 LM358APWR L358A
MSOP/VSSOP (DGK) Reel of 2500 LM358ADGKR M6_
PDIP (P) Tube of 50 LM258P LM258P
5 mV
30 V
SOIC (D)
Tube of 75 LM258D
LM258
5 mV 30 V SOIC (D) Reel of 2500 LM258DR LM258
−25°C to 85°C
MSOP/VSSOP (DGK) Reel of 2500 LM258DGKR M2_
−25°C to 85°CPDIP (P) Tube of 50 LM258AP LM258AP
3 mV
30 V
SOIC (D)
Tube of 75 LM258AD
LM258A
3 mV 30 V SOIC (D) Reel of 2500 LM258ADR LM258A
MSOP/VSSOP (DGK) Reel of 2500 LM258ADGKR M3_
PDIP (P) Tube of 50 LM2904P LM2904P
SOIC (D)
Tube of 75 LM2904D
LM2904
SOIC (D) Reel of 2500 LM2904DR LM2904
7 mV 26 V SOP (PS) Reel of 2000 LM2904PSR L2904
7 mV
26 V
TSSOP (PW)
Tube of 150 LM2904PW
L2904
−40°C to 125°CTSSOP (PW) Reel of 2000 LM2904PWR L2904
−40 C to 125 C
MSOP/VSSOP (DGK) Reel of 2500 LM2904DGKR MB_
7 mV
32 V
SOIC (D) Reel of 2500 LM2904VQDR L2904V
7 mV 32 V TSSOP (PW) Reel of 2000 LM2904VQPWR L2904V
2 mV
32 V
SOIC (D) Reel of 2500 LM2904AVQDR L2904AV
2 mV 32 V TSSOP (PW) Reel of 2000 LM2904AVQPWR L2904AV
5 mV
30 V
CDIP (JG) Tube of 50 LM158JG LM158JG
−55°C to 125°C
5 mV 30 V LCCC (FK) Tube of 55 LM158FK LM158FK
−55
°
C to 125
°
C
2 mV
30 V
CDIP (JG) Tube of 50 LM158AJG LM158AJG
2 mV
30 V
LCCC (FK) Tube of 55 LM158AFK LM158AFK
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
The actual top-side marking has one additional character that designates the assembly/test site.
   
   
  
SLOS068P − JUNE 1976 − REVISED SEPTEMBER 2004
3
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
symbol (each amplifier)
IN+
IN− OUT
+
schematic (each amplifier)
VCC+
OUT
GND (or VCC−)
To Other Amplifier
IN−
IN+
6-µA
Current
Regulator
6-µA
Current
Regulator
100-µA
Current
Regulator
50-µA
Current
Regulator
Epi-FET
Diodes
Resistors
Transistors
Capacitors
COMPONENT COUNT
1
2
7
51
2
   
   
  
SLOS068P − JUNE 1976 − REVISED SEPTEMBER 2004
4POST OFFICE BOX 655303 DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
LM158, LM158A
LM258, LM258A
LM358, LM358A
LM2904V
LM2904 UNIT
Supply voltage, VCC (see Note 1) ±16 or 32 ±13 or 26 V
Differential input voltage, VID (see Note 2) ±32 ±26 V
Input voltage, VI (either input) −0.3 to 32 −0.3 to 26 V
Duration of output short circuit (one amplifier) to ground
at (or below) 25°C free-air temperature (VCC 15 V) (see Note 3) Unlimited Unlimited
D package 97 97
DGK package 172 172
Package thermal impedance, q
JA
(see Notes 4 and 5) P package 85 85 °C/W
Package thermal impedance, qJA (see Notes 4 and 5)
PS package 95 95
C/W
PW package 149 149
Package thermal impedance, qJC (see Notes 6 and 7)
FK package 5.61
°C/W
Package thermal impedance, qJC (see Notes 6 and 7) JG package 14.5 °C/W
LM158, LM158A −55 to 125
Operating free-air temperature range, TA
LM258, LM258A −25 to 85
°C
Operating free-air temperature range, TALM358, LM358A 0 to 70 °C
LM2904 −40 to 125 −40 to 125
Operating virtual junction temperature, TJ150 150 °C
Case temperature for 60 seconds FK package 260 °C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds JG package 300 300 °C
Storage temperature range, Tstg −65 to 150 −65 to 150 °C
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages and VCC specified for measurement of IOS, are with respect to the network ground
terminal.
2. Differential voltages are at IN+ with respect to IN−.
3. Short circuits from outputs to VCC can cause excessive heating and eventual destruction.
4. Maximum power dissipation is a function of TJ(max), qJA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) − TA)/qJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
5. The package thermal impedance is calculated in accordance with JESD 51-7.
6. Maximum power dissipation is a function of TJ(max), qJC, and TC. The maximum allowable power dissipation at any allowable case
temperature is PD = (TJ(max) − TC)/qJC. Operating at the absolute maximum TJ of 150°C can affect reliability.
7. The package thermal impedance is calculated in accordance with MIL-STD-883.
   
   
  
SLOS068P − JUNE 1976 − REVISED SEPTEMBER 2004
5
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONST
A
LM158
LM258 LM358
PARAMETER
TEST CONDITIONS
TA
MIN TYP§MAX MIN TYP§MAX
VIO
Input offset voltage
VCC = 5 V to MAX,
VIC = VICR(min),
25°C 3 5 3 7
V
IO
Input offset voltage
CC
V
IC
= V
ICR(min)
,
V
O
= 1.4 V Full range 7 9
aVIO
Average temperature
coefficient of
input offset voltage Full range 7 7 µV/°C
IIO
Input offset current
VO = 1.4 V
25°C 2 30 2 50
I
IO
Input offset current
V
O
= 1.4 V
Full range 100 150
aIIO
Average temperature
coefficient of
input offset current Full range 10 10 pA/°C
IIB
Input bias current
VO = 1.4 V
25°C −20 −150 −20 −250
I
IB
Input bias current
V
O
= 1.4 V
Full range −300 −500
VICR
Common-mode
VCC = 5 V to MAX
25°C0 to
VCC − 1.5 0 to
VCC − 1.5
V
ICR
Common-mode
input voltage range
V
CC
= 5 V to MAX
Full range 0 to
VCC − 2 0 to
VCC − 2
RL 2 k25°C VCC − 1.5 VCC − 1.5
VOH
High-level
RL 10 k25°C
V
OH
High-level
output voltage
VCC = MAX
RL = 2 kFull range 26 26
output voltage
V
CC
= MAX
RL 10 kFull range 27 28 27 28
VOL Low-level
output voltage RL 10 kFull range 5 20 5 20 mV
AVD
Large-signal
differential
VCC = 15 V,
VO = 1 V to 11 V,
25°C 50 100 25 100
A
VD
differential
voltage amplification
CC
V
O
= 1 V to 11 V,
R
L
2 kFull range 25 15
CMRR Common-mode
rejection ratio VCC = 5 V to MAX,
VIC = VICR(min) 25°C 70 80 65 80 dB
kSVR Supply-voltage
rejection ratio
(VDD/VIO)VCC = 5 V to MAX 25°C 65 100 65 100 dB
VO1/VO2 Crosstalk attenuation f = 1 kHz to 20 kHz 25°C 120 120 dB
VCC = 15 V
,
VID = 1 V,
Source
25°C −20 −30 −20 −30
IO
Output current
CC
V
ID
= 1 V,
V
O
= 0
Source
Full range −10 −10
I
O
Output current
VCC = 15 V
,
VID = −1 V,
Sink
25°C 10 20 10 20
CC
V
ID
= −1 V,
V
O
= 15 V
Sink
Full range 5 5
IOOutput current VID = −1 V, VO = 200 mV 25°C 12 30 12 30 µA
IOS Short-circuit
output current VCC at 5 V, GND at −5 V,
VO = 0 25°C±40 ±60 ±40 ±60 mA
Supply current
VO = 2.5 V, No load Full range 0.7 1.2 0.7 1.2
ICC
Supply current
(two amplifiers) VCC = MAX, VO = 0.5 V,
No load Full range 1 2 1 2 mA
All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified. MAX VCC for
testing purposes is 26 V for the LM2904 and 30 V for others.
Full range is −55°C to 125°C for LM158, −25°C to 85°C for LM258, 0°C to 70°C for LM358, and −40°C to 125°C for LM2904.
§All typical values are at TA = 25°C.
   
   
  
SLOS068P − JUNE 1976 − REVISED SEPTEMBER 2004
6POST OFFICE BOX 655303 DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
LM2904
UNIT
PARAMETER
TEST CONDITIONS
T
A
MIN TYP§MAX
UNIT
V = 5 V to MAX,
Non-A devices
25°C 3 7
VIO
Input offset voltage
VCC = 5 V to MAX
,
VIC = VICR(min),
Non-A devices Full range 10
mV
VIO Input offset voltage
CC
V
IC
= V
ICR(min)
,
VO = 1.4 V
A-suffix devices
25°C 1 2 mV
VO = 1.4 V
A-suffix devices Full range 4
aVIO Average temperature coefficient
of input offset voltage Full range 7µV/°C
Non-V device
25°C 2 50
IIO
Input offset current
VO = 1.4 V
Non-V device Full range 300
nA
IIO Input offset current VO = 1.4 V
V-suffix device
25°C 2 50 nA
V-suffix device Full range 150
aIIO Average temperature coefficient
of input offset current Full range 10 pA/°C
IIB
Input bias current
VO = 1.4 V
25°C −20 −250
nA
IIB Input bias current VO = 1.4 V Full range −500 nA
VICR
Common-mode input voltage
VCC = 5 V to MAX
25°C0 to
VCC − 1.5
V
VICR
Common-mode input voltage
range VCC = 5 V to MAX Full range 0 to
VCC − 2
V
RL 10 k25°C VCC − 1.5
VCC = MAX,
RL = 2 kFull range 22
V
OH
High-level output voltage
VCC = MAX,
Non-V device RL 10 kFull range 23 24 V
VOH
High-level output voltage
VCC = MAX,
RL = 2 kFull range 26
V
VCC = MAX,
V-suffix device RL 10 kFull range 27 28
VOL Low-level output voltage RL 10 kFull range 5 20 mV
AVD
Large-signal differential
VCC = 15 V, VO = 1 V to 11 V,
25°C 25 100
V/mV
AVD
Large-signal differential
voltage amplification
VCC = 15 V, VO = 1 V to 11 V,
RL 2 kFull range 15 V/mV
CMRR
Common-mode rejection ratio
VCC = 5 V to MAX,
Non-V device 25°C 50 80
dB
CMRR Common-mode rejection ratio
VCC = 5 V to MAX,
VIC = VICR(min) V-suffix device 25°C 65 80 dB
kSVR Supply-voltage rejection ratio
(VDD/VIO)VCC = 5 V to MAX 25°C 65 100 dB
VO1/VO2 Crosstalk attenuation f = 1 kHz to 20 kHz 25°C 120 dB
VCC = 15 V,
Source
25°C −20 −30 mA
VCC = 15 V,
VID = 1 V, VO = 0 Source Full range −10 mA
IO
Output current
VCC = 15 V,
VID = −1 V,
Sink
25°C 10 20 mA
IOOutput current
CC
V
ID
= −1 V,
VO = 15 V Sink Full range 5 mA
VID = −1 V,
Non-V device 25°C 30
A
VID = −1 V,
VO = 200 mV V-suffix device 25°C 12 40 µA
IOS Short-circuit output current VCC at 5 V, GND at −5 V, VO = 0 25°C±40 ±60 mA
ICC
Supply current (two amplifiers)
VO = 2.5 V, No load Full range 0.7 1.2
mA
I
CC
Supply current (two amplifiers)
VCC = MAX, VO = 0.5 V, No load Full range 1 2
mA
All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified. MAX VCC for
testing purposes is 26 V for the LM2904, 32 V for the LM2904V, and 30 V for others.
Full range is −55°C to 125°C for LM158, −25°C to 85°C for LM258, 0°C to 70°C for LM358, and −40°C to 125°C for LM2904.
§All typical values are at TA = 25°C.
   
   
  
SLOS068P − JUNE 1976 − REVISED SEPTEMBER 2004
7
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
LM158A LM258A
PARAMETER
TEST CONDITIONS
T
A
MIN TYP§MAX MIN TYP§MAX
VIO
Input offset voltage
VCC = 5 V to 30 V,
VIC = VICR(min),
25°C 2 2 3
V
IO
Input offset voltage
CC
V
IC
= V
ICR(min)
,
V
O
= 1.4 V Full range 4 4
aVIO
Average
temperature
coefficient of
input offset voltage
Full range 7 15*7 15 µV/°C
IIO
Input offset current
VO = 1.4 V
25°C 2 10 2 15
I
IO
Input offset current
V
O
= 1.4 V
Full range 30 30
aIIO
Average
temperature
coefficient of
input offset current
Full range 10 200 10 200 pA/°C
IIB
Input bias current
VO = 1.4 V
25°C −15 −50 −15 −80
I
IB
Input bias current
V
O
= 1.4 V
Full range −100 −100
VICR
Common-mode
VCC = 30 V
25°C0 to
VCC − 1.5 0 to
VCC − 1.5
V
ICR
Common-mode
input voltage range
V
CC
= 30 V
Full range 0 to
VCC − 2 0 to
VCC − 2
High-level
RL 2 k25°C VCC − 1.5 VCC − 1.5
V
OH
High-level
output voltage
VCC = 30 V
RL = 2 kFull range 26 26 V
VOH
output voltage
V
CC
= 30 V
RL 10 kFull range 27 28 27 28
VOL Low-level
output voltage RL 10 kFull range 5 20 5 20 mV
AVD
Large-signal
differential
VCC = 15 V,
VO = 1 V to 11 V,
25°C 50 100 50 100
A
VD
differential
voltage amplification
CC
V
O
= 1 V to 11 V,
R
L
2 kFull range 25 25
CMRR Common-mode
rejection ratio 25°C 70 80 70 80 dB
kSVR Supply-voltage
rejection ratio
(VDD/VIO)25°C 65 100 65 100 dB
VO1/VO2 Crosstalk
attenuation f = 1 kHz to 20 kHz 25°C 120 120 dB
VCC = 15 V
,
VID = 1 V,
Source
25°C −20 −30 −60 −20 −30 −60
CC
V
ID
= 1 V,
V
O
= 0
Source
Full range −10 −10
IOOutput current VCC = 15 V
,
VID = −1 V,
Sink
25°C 10 20 10 20
O
CC
V
ID
= −1 V,
V
O
= 15
Sink
Full range 5 5
VID = −1 V, VO = 200 mV 25°C 12 30 12 30 µA
IOS Short-circuit output
current VCC at 5 V, GND at −5 V,
VO = 0 25°C±40 ±60 ±40 ±60 mA
Supply current (two
VO = 2.5 V, No load Full range 0.7 1.2 0.7 1.2
ICC
Supply current (two
amplifiers) VCC = MAX, VO = 0.5 V,
No load Full range 1 2 1 2 mA
*On products compliant to MIL-PRF-38535, this parameter is not production tested.
All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified. MAX VCC for
testing purposes is 26 V for LM2904 and 30 V for others.
Full range is −55°C to 125°C for LM158A, −25°C to 85°C for LM258A, and 0°C to 70°C for LM358A.
§All typical values are at TA = 25°C.
   
   
  
SLOS068P − JUNE 1976 − REVISED SEPTEMBER 2004
8POST OFFICE BOX 655303 DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
LM358A
UNIT
PARAMETER
TEST CONDITIONS
T
A
MIN TYP§MAX
UNIT
VIO
Input offset voltage
VCC = 5 V to 30 V,
25°C 2 3
mV
VIO Input offset voltage
VCC = 5 V to 30 V,
VIC = VICR(min), VO = 1.4 V Full range 5mV
aVIO Average temperature coefficient of
input offset voltage Full range 7 20 µV/°C
IIO
Input offset current
VO = 1.4 V
25°C 2 30
nA
IIO Input offset current VO = 1.4 V Full range 75 nA
aIIO Average temperature coefficient of
input offset current Full range 10 300 pA/°C
IIB
Input bias current
VO = 1.4 V
25°C −15 −100
nA
IIB Input bias current VO = 1.4 V Full range −200 nA
VICR
Common-mode input voltage range
VCC = 30 V
25°C0 to
VCC − 1.5
V
VICR Common-mode input voltage range VCC = 30 V Full range 0 to
VCC − 2
V
RL 2 k25°C VCC − 1.5
V
OH
High-level output voltage
VCC = 30 V
RL = 2 kFull range 26 V
VOH
High-level output voltage
VCC = 30 V RL 10 kFull range 27 28
V
VOL Low-level output voltage RL 10 kFull range 5 20 mV
AVD
Large-signal differential
VCC = 15 V, VO = 1 V to 11 V,
25°C 25 100
V/mV
AVD
Large-signal differential
voltage amplification
VCC = 15 V, VO = 1 V to 11 V,
RL 2 kFull range 15 V/mV
CMRR Common-mode rejection ratio 25°C 65 80 dB
kSVR Supply-voltage rejection ratio
(VDD/VIO)25°C 65 100 dB
VO1/VO2 Crosstalk attenuation f = 1 kHz to 20 kHz 25°C 120 dB
VCC = 15 V,
VID = 1 V,
Source
25°C −20 −30 −60
CC
V
ID
= 1 V,
VO = 0 Source Full range −10
mA
IOOutput current VCC = 15 V,
VID = −1 V,
Sink
25°C 10 20 mA
O
CC
V
ID
= −1 V,
VO = 15 V Sink Full range 5
VID = −1 V, VO = 200 mV 25°C 30 µA
IOS Short-circuit output current VCC at 5 V, GND at −5 V, VO = 0 25°C±40 ±60 mA
ICC
Supply current (two amplifiers)
VO = 2.5 V, No load Full range 0.7 1.2
mA
I
CC
Supply current (two amplifiers)
VCC = MAX, VO = 0.5 V, No load Full range 1 2
mA
All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified. MAX VCC for
testing purposes is 26 V for LM2904 and 30 V for others.
Full range is −55°C to 125°C for LM158A, −25°C to 85°C for LM258A, and 0°C to 70°C for LM358A.
§All typical values are at TA = 25°C.
   
   
  
SLOS068P − JUNE 1976 − REVISED SEPTEMBER 2004
9
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
operating conditions, VCC = ±15 V, TA = 25°C
PARAMETER TEST CONDITIONS TYP UNIT
SR Slew rate at unity gain RL = 1 M, CL = 30 pF, VI = ±10 V
(see Figure 1) 0.3 V/µs
B1Unity-gain bandwidth RL = 1 M, CL = 20 pF (see Figure 1) 0.7 MHz
VnEquivalent input noise voltage RS = 100 , VI = 0 V, f = 1 kHz
(see Figure 2) 40 nV/Hz
+VO
RL
CL
VI
VCC+
VCC−
Figure 1. Unity-Gain Amplifier
+VO
100 VCC+
VCC−
RS
900
VI = 0 V
Figure 2. Noise-Test Circuit
PACKAGING INFORMATION
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
5962-87710012A ACTIVE LCCC FK 20 1 None POST-PLATE Level-NC-NC-NC
5962-8771001PA ACTIVE CDIP JG 8 1 None A42 SNPB Level-NC-NC-NC
5962-87710022A ACTIVE LCCC FK 20 1 None POST-PLATE Level-NC-NC-NC
5962-8771002PA ACTIVE CDIP JG 8 1 None A42 SNPB Level-NC-NC-NC
LM158AFKB ACTIVE LCCC FK 20 1 None POST-PLATE Level-NC-NC-NC
LM158AJG ACTIVE CDIP JG 8 1 None A42 SNPB Level-NC-NC-NC
LM158AJGB ACTIVE CDIP JG 8 1 None A42 SNPB Level-NC-NC-NC
LM158FKB ACTIVE LCCC FK 20 1 None POST-PLATE Level-NC-NC-NC
LM158JG ACTIVE CDIP JG 8 1 None A42 SNPB Level-NC-NC-NC
LM158JGB ACTIVE CDIP JG 8 1 None A42 SNPB Level-NC-NC-NC
LM258AD ACTIVE SOIC D 8 75 Pb-Free
(RoHS) CU NIPDAU Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
LM258ADGKR ACTIVE MSOP DGK 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-2-260C-1YEAR
LM258ADR ACTIVE SOIC D 8 2500 Pb-Free
(RoHS) CU NIPDAU Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
LM258AP ACTIVE PDIP P 8 50 Pb-Free
(RoHS) CU NIPDAU Level-NC-NC-NC
LM258D ACTIVE SOIC D 8 75 Pb-Free
(RoHS) CU NIPDAU Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
LM258DGKR ACTIVE MSOP DGK 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-2-260C-1YEAR
LM258DR ACTIVE SOIC D 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LM258P ACTIVE PDIP P 8 50 Pb-Free
(RoHS) CU NIPDAU Level-NC-NC-NC
LM2904AVQDR ACTIVE SOIC D 8 2500 Pb-Free
(RoHS) CU NIPDAU Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
LM2904AVQPWR ACTIVE TSSOP PW 8 2000 None CU NIPDAU Level-1-250C-UNLIM
LM2904D ACTIVE SOIC D 8 75 Pb-Free
(RoHS) CU NIPDAU Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
LM2904DGKR ACTIVE MSOP DGK 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-2-260C-1YEAR
LM2904DR ACTIVE SOIC D 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LM2904P ACTIVE PDIP P 8 50 Pb-Free
(RoHS) CU NIPDAU Level-NC-NC-NC
LM2904PSR ACTIVE SO PS 8 2000 Pb-Free
(RoHS) CU NIPDAU Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
LM2904PW ACTIVE TSSOP PW 8 150 Pb-Free
(RoHS) CU NIPDAU Level-1-250C-UNLIM
LM2904PWLE OBSOLETE TSSOP PW 8 None Call TI Call TI
LM2904PWR ACTIVE TSSOP PW 8 2000 Pb-Free
(RoHS) CU NIPDAU Level-1-250C-UNLIM
LM2904QD OBSOLETE SOIC D 8 None Call TI Call TI
LM2904QDR OBSOLETE SOIC D 8 Pb-Free
(RoHS) CU NIPDAU Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
PACKAGE OPTION ADDENDUM
www.ti.com 4-Mar-2005
Addendum-Page 1
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
LM2904QP OBSOLETE PDIP P 8 None Call TI Call TI
LM2904VQDR ACTIVE SOIC D 8 2500 Pb-Free
(RoHS) CU NIPDAU Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
LM2904VQPWR ACTIVE TSSOP PW 8 2000 None CU NIPDAU Level-1-250C-UNLIM
LM358AD ACTIVE SOIC D 8 75 Pb-Free
(RoHS) CU NIPDAU Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
LM358ADGKR ACTIVE MSOP DGK 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-2-260C-1YEAR
LM358ADR ACTIVE SOIC D 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LM358AP ACTIVE PDIP P 8 50 Pb-Free
(RoHS) CU NIPDAU Level-NC-NC-NC
LM358APW ACTIVE TSSOP PW 8 150 Pb-Free
(RoHS) CU NIPDAU Level-1-250C-UNLIM
LM358APWR ACTIVE TSSOP PW 8 2000 Pb-Free
(RoHS) CU NIPDAU Level-1-250C-UNLIM
LM358D ACTIVE SOIC D 8 75 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LM358DGKR ACTIVE MSOP DGK 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-2-260C-1YEAR
LM358DR ACTIVE SOIC D 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LM358P ACTIVE PDIP P 8 50 Pb-Free
(RoHS) CU NIPDAU Level-NC-NC-NC
LM358PSLE OBSOLETE SO PS 8 None Call TI Call TI
LM358PSR ACTIVE SO PS 8 2000 Pb-Free
(RoHS) CU NIPDAU Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
LM358PW ACTIVE TSSOP PW 8 150 Pb-Free
(RoHS) CU NIPDAU Level-1-250C-UNLIM
LM358PWLE OBSOLETE TSSOP PW 8 None Call TI Call TI
LM358PWR ACTIVE TSSOP PW 8 2000 Pb-Free
(RoHS) CU NIPDAU Level-1-250C-UNLIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
PACKAGE OPTION ADDENDUM
www.ti.com 4-Mar-2005
Addendum-Page 2
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 4-Mar-2005
Addendum-Page 3
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUAR Y 1997
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE
0.310 (7,87)
0.290 (7,37)
0.014 (0,36)
0.008 (0,20)
Seating Plane
4040107/C 08/96
5
4
0.065 (1,65)
0.045 (1,14)
8
1
0.020 (0,51) MIN
0.400 (10,16)
0.355 (9,00)
0.015 (0,38)
0.023 (0,58)
0.063 (1,60)
0.015 (0,38)
0.200 (5,08) MAX
0.130 (3,30) MIN
0.245 (6,22)
0.280 (7,11)
0.100 (2,54)
0°–15°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification.
E. Falls within MIL STD 1835 GDIP1-T8
MECHANICAL DATA
MLCC006B – OCTOBER 1996
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER
4040140/D 10/96
28 TERMINAL SHOWN
B
0.358
(9,09)
MAX
(11,63)
0.560
(14,22)
0.560
0.458
0.858
(21,8)
1.063
(27,0)
(14,22)
A
NO. OF
MINMAX
0.358
0.660
0.761
0.458
0.342
(8,69)
MIN
(11,23)
(16,26)
0.640
0.739
0.442
(9,09)
(11,63)
(16,76)
0.962
1.165
(23,83)
0.938
(28,99)
1.141
(24,43)
(29,59)
(19,32)(18,78)
**
20
28
52
44
68
84
0.020 (0,51)
TERMINALS
0.080 (2,03)
0.064 (1,63)
(7,80)
0.307
(10,31)
0.406
(12,58)
0.495
(12,58)
0.495
(21,6)
0.850
(26,6)
1.047
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.035 (0,89)
0.010 (0,25)
12
1314151618 17
11
10
8
9
7
5
432
0.020 (0,51)
0.010 (0,25)
6
12826 27
19
21
B SQ
A SQ 22
23
24
25
20
0.055 (1,40)
0.045 (1,14)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a metal lid.
D. The terminals are gold plated.
E. Falls within JEDEC MS-004
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
P (R-PDIP-T8) PLASTIC DUAL-IN-LINE
8
4
0.015 (0,38)
Gage Plane
0.325 (8,26)
0.300 (7,62)
0.010 (0,25) NOM
MAX
0.430 (10,92)
4040082/D 05/98
0.200 (5,08) MAX
0.125 (3,18) MIN
5
0.355 (9,02)
0.020 (0,51) MIN
0.070 (1,78) MAX
0.240 (6,10)
0.260 (6,60)
0.400 (10,60)
1
0.015 (0,38)
0.021 (0,53)
Seating Plane
M
0.010 (0,25)
0.100 (2,54)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,65 M
0,10
0,10
0,25
0,50
0,75
0,15 NOM
Gage Plane
28
9,80
9,60
24
7,90
7,70
2016
6,60
6,40
4040064/F 01/97
0,30
6,60
6,20
80,19
4,30
4,50
7
0,15
14
A
1
1,20 MAX
14
5,10
4,90
8
3,10
2,90
A MAX
A MIN
DIM PINS **
0,05
4,90
5,10
Seating Plane
0°–8°
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’ s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of T I products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DSP dsp.ti.com Broadband www.ti.com/broadband
Interface interface.ti.com Digital Control www.ti.com/digitalcontrol
Logic logic.ti.com Military www.ti.com/military
Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork
Microcontrollers microcontroller.ti.com Security www.ti.com/security
Telephony www.ti.com/telephony
Video & Imaging www.ti.com/video
Wireless www.ti.com/wireless
Mailing Address: Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2005, Texas Instruments Incorporated