SLOS068P - JUNE 1976 - REVISED SEPTEMBER 2004 D D D D D LM158, LM158A . . . JG PACKAGE LM258, LM258A . . . D, DGK, OR P PACKAGE LM358 . . . D, DGK, P, PS, OR PW PACKAGE LM358A . . . D, DGK, P, OR PW PACKAGE LM2904 . . . D, DGK, P, PS, OR PW PACKAGE (TOP VIEW) 1OUT 1IN- 1IN+ GND 1 8 2 7 3 6 4 5 VCC 2OUT 2IN- 2IN+ LM158, LM158A . . . FK PACKAGE (TOP VIEW) NC 1IN- NC 1IN+ NC 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 NC 2OUT NC 2IN- NC NC GND NC 2IN+ NC D - Single Supply . . . 3 V to 32 V (26 V for LM2904) - or Dual Supplies . . . +1.5 V to +16 V (+13 V for LM2904) Low Supply-Current Drain, Independent of Supply Voltage . . . 0.7 mA Typ Common-Mode Input Voltage Range Includes Ground, Allowing Direct Sensing Near Ground Low Input Bias and Offset Parameters: - Input Offset Voltage . . . 3 mV Typ A Versions . . . 2 mV Typ - Input Offset Current . . . 2 nA Typ - Input Bias Current . . . 20 nA Typ A Versions . . . 15 nA Typ Differential Input Voltage Range Equal to Maximum-Rated Supply Voltage . . . 32 V (26 V for LM2904) Open-Loop Differential Voltage Amplification . . . 100 V/mV Typ Internal Frequency Compensation NC 1OUT NC V CC+ NC D Wide Supply Range: description/ordering information NC - No internal connection These devices consist of two independent, high-gain, frequency-compensated operational amplifiers designed to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3 V to 32 V (3 V to 26 V for the LM2904), and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage. Applications include transducer amplifiers, dc amplification blocks, and all the conventional operational amplifier circuits that now can be implemented more easily in single-supply-voltage systems. For example, these devices can be operated directly from the standard 5-V supply used in digital systems and easily can provide the required interface electronics without additional 5-V supplies. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2004, Texas Instruments Incorporated !" # $%&" !# '%()$!" *!"&+ *%$"# $ " #'&$$!"# '& ",& "&# &-!# #"%&"# #"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0 !)) '!!&"&#+ '*%$"# $')!" " 11 !)) '!!&"&# !& "&#"&* %)&## ",&.#& "&*+ !)) ",& '*%$"# '*%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0 !)) '!!&"&#+ POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SLOS068P - JUNE 1976 - REVISED SEPTEMBER 2004 description/ordering information (continued) ORDERING INFORMATION TA VIOmax AT 25C MAX TESTED VCC PDIP (P) 30 V LM358P Tube of 75 LM358D Reel of 2500 LM358DR Reel of 2000 LM358PSR Tube of 150 LM358PW Reel of 2000 LM358PWR MSOP/VSSOP (DGK) Reel of 2500 LM358DGKR M5_ PDIP (P) Tube of 50 LM358AP LM358AP Tube of 75 LM358AD Reel of 2500 LM358ADR Tube of 150 LM358APW Reel of 2000 LM358APWR MSOP/VSSOP (DGK) Reel of 2500 LM358ADGKR M6_ PDIP (P) Tube of 50 LM258P LM258P Tube of 75 LM258D Reel of 2500 LM258DR MSOP/VSSOP (DGK) Reel of 2500 LM258DGKR M2_ PDIP (P) Tube of 50 LM258AP LM258AP Tube of 75 LM258AD Reel of 2500 LM258ADR MSOP/VSSOP (DGK) Reel of 2500 LM258ADGKR M3_ PDIP (P) Tube of 50 LM2904P LM2904P Tube of 75 LM2904D Reel of 2500 LM2904DR Reel of 2000 LM2904PSR Tube of 150 LM2904PW Reel of 2000 LM2904PWR MSOP/VSSOP (DGK) Reel of 2500 LM2904DGKR MB_ SOIC (D) Reel of 2500 LM2904VQDR L2904V TSSOP (PW) Reel of 2000 LM2904VQPWR L2904V SOIC (D) Reel of 2500 LM2904AVQDR L2904AV TSSOP (PW) Reel of 2000 LM2904AVQPWR L2904AV CDIP (JG) Tube of 50 LM158JG LM158JG LCCC (FK) Tube of 55 LM158FK LM158FK CDIP (JG) Tube of 50 LM158AJG LM158AJG LCCC (FK) Tube of 55 LM158AFK SOP (PS) TSSOP (PW) 0C 0 C to 70 70C C SOIC (D) 3 mV 30 V TSSOP (PW) 5 mV 30 V -25C to 85C 3 mV 30 V SOIC (D) SOIC (D) SOIC (D) 7 mV 26 V SOP (PS) TSSOP (PW) -40C -40 C to 125 125C C 7 mV 2 mV 5 mV 32 V 32 V 30 V -55C to 125C 2 mV 30 V TOP-SIDE MARKING Tube of 50 SOIC (D) 7 mV ORDERABLE PART NUMBER PACKAGE LM358P LM358 L358 L358 LM358A L358A LM258 LM258A LM2904 L2904 L2904 LM158AFK Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. The actual top-side marking has one additional character that designates the assembly/test site. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLOS068P - JUNE 1976 - REVISED SEPTEMBER 2004 symbol (each amplifier) IN+ + - IN- OUT schematic (each amplifier) VCC+ 6-A Current Regulator 6-A Current Regulator 100-A Current Regulator OUT IN- 50-A Current Regulator IN+ GND (or VCC-) To Other Amplifier COMPONENT COUNT Epi-FET Diodes Resistors Transistors Capacitors POST OFFICE BOX 655303 1 2 7 51 2 * DALLAS, TEXAS 75265 3 SLOS068P - JUNE 1976 - REVISED SEPTEMBER 2004 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) LM158, LM158A LM258, LM258A LM358, LM358A LM2904V 16 or 32 Supply voltage, VCC (see Note 1) 32 Differential input voltage, VID (see Note 2) LM2904 13 or 26 V 26 V V Input voltage, VI (either input) -0.3 to 32 -0.3 to 26 Duration of output short circuit (one amplifier) to ground at (or below) 25C free-air temperature (VCC 15 V) (see Note 3) Unlimited Unlimited D package DGK package Package thermal impedance, qJA (see Notes 4 and 5) Package thermal impedance, qJC (see Notes 6 and 7) Operating free-air temperature range, TA 97 97 172 172 P package 85 85 PS package 95 95 PW package 149 149 FK package 5.61 JG package 14.5 LM158, LM158A -55 to 125 LM258, LM258A -25 to 85 LM358, LM358A 0 to 70 LM2904 Operating virtual junction temperature, TJ -40 to 125 150 Case temperature for 60 seconds FK package 260 Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds JG package 300 UNIT C/W C/W C/W C -40 to 125 150 C C 300 C C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages and VCC specified for measurement of IOS, are with respect to the network ground terminal. 2. Differential voltages are at IN+ with respect to IN-. 3. Short circuits from outputs to VCC can cause excessive heating and eventual destruction. 4. Maximum power dissipation is a function of TJ(max), qJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) - TA)/qJA. Operating at the absolute maximum TJ of 150C can affect reliability. 5. The package thermal impedance is calculated in accordance with JESD 51-7. 6. Maximum power dissipation is a function of TJ(max), qJC, and TC. The maximum allowable power dissipation at any allowable case temperature is PD = (TJ(max) - TC)/qJC. Operating at the absolute maximum TJ of 150C can affect reliability. 7. The package thermal impedance is calculated in accordance with MIL-STD-883. Storage temperature range, Tstg 4 -65 to 150 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 -65 to 150 SLOS068P - JUNE 1976 - REVISED SEPTEMBER 2004 electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) PARAMETER VIO Input offset voltage aV Average temperature coefficient of input offset voltage IO IIO Input offset current aI Average temperature coefficient of input offset current IO IIB Input bias current VICR Common-mode input voltage range VOH VOL AVD CMRR kSVR VO1/VO2 IO High-level output voltage TEST CONDITIONS VCC = 5 V to MAX, VIC = VICR(min), VO = 1.4 V VO = 1.4 V VO = 1.4 V IOS Short-circuit output current ICC Supply current (two amplifiers) 5 MIN UNIT TYP MAX 3 7 7 Full range 7 25C 2 10 25C -20 RL 2 k 25C RL 10 k 25C 9 30 2 10 -150 -20 0 to VCC - 1.5 0 to VCC - 2 VCC - 1.5 VCC - 1.5 26 RL 10 k Full range 27 Full range -250 5 27 20 100 V 28 5 25 nA V 26 28 nA pA/C -500 0 to VCC - 1.5 0 to VCC - 2 Full range 50 150 -300 RL = 2 k V/C 7 100 Full range Full range VCC = MAX LM358 mV Full range VCC = 5 V to MAX VCC = 15 V, VO = 1 V to 11 V, RL 2 k VCC = 5 V to MAX, VIC = VICR(min) Output current 3 25C 25C Large-signal differential voltage amplification Common-mode rejection ratio IO MAX Full range RL 10 k Output current LM158 LM258 MIN TYP Full range Low-level output voltage Supply-voltage rejection ratio (VDD/VIO) Crosstalk attenuation TA 20 mV 25C 50 100 Full range 25 25C 70 80 65 80 dB VCC = 5 V to MAX 25C 65 100 65 100 dB f = 1 kHz to 20 kHz 25C 120 dB VCC = 15 V, VID = 1 V, VO = 0 25C -20 Full range -10 25C 10 Full range 5 25C 12 V/mV 15 120 -30 -20 -30 Source VCC = 15 V, Sink VID = -1 V, VO = 15 V VID = -1 V, VO = 200 mV VCC at 5 V, GND at -5 V, VO = 0 VO = 2.5 V, No load VCC = MAX, VO = 0.5 V, No load -10 mA 20 10 20 5 30 12 A 30 25C 40 60 40 60 Full range 0.7 1.2 0.7 1.2 Full range 1 2 1 2 mA mA All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified. MAX VCC for testing purposes is 26 V for the LM2904 and 30 V for others. Full range is -55C to 125C for LM158, -25C to 85C for LM258, 0C to 70C for LM358, and -40C to 125C for LM2904. All typical values are at TA = 25C. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SLOS068P - JUNE 1976 - REVISED SEPTEMBER 2004 electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA MIN LM2904 TYP 25C VIO aV IO Input offset voltage VCC = 5 V to MAX, VIC = VICR(min), VO = 1.4 V Non-A devices Average temperature coefficient of input offset voltage Input offset current VO = 1.4 V aI IO Average temperature coefficient of input offset current IIB Input bias current VICR Common-mode input voltage range VO = 1.4 V High-level output voltage Full range Full range 7 25C 2 Full range 2 10 25C -20 Full range 25C Full range RL 10 k Full range 23 VCC = MAX, V-suffix device RL = 2 k Full range 26 RL 10 k Full range 27 Large-signal differential voltage amplification VCC = 15 V, VO = 1 V to 11 V, RL 2 k 25C 25 Full range 15 25C 50 80 Common-mode rejection ratio VCC = 5 V to MAX, VIC = VICR(min) Non-V device CMRR V-suffix device 25C 65 80 kSVR Supply-voltage rejection ratio (VDD/VIO) VCC = 5 V to MAX 25C 65 100 VO1/VO2 Crosstalk attenuation f = 1 kHz to 20 kHz 25C VCC = 15 V, VID = 1 V, VO = 0 25C -20 Source Full range -10 VCC = 15 V, VID = -1 V, VO = 15 V 25C 10 Sink Full range 5 IOS ICC Short-circuit output current V 5 20 100 V/mV dB dB 120 dB -30 mA mA 20 mA mA 30 12 mV A A 40 25C 40 60 Full range 0.7 1.2 mA mA VCC = MAX, VO = 0.5 V, No load Full range 1 2 All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified. MAX VCC for testing purposes is 26 V for the LM2904, 32 V for the LM2904V, and 30 V for others. Full range is -55C to 125C for LM158, -25C to 85C for LM258, 0C to 70C for LM358, and -40C to 125C for LM2904. All typical values are at TA = 25C. 6 Supply current (two amplifiers) VCC at 5 V, GND at -5 V, VO = 0 VO = 2.5 V, No load nA 28 AVD 25C -250 24 Full range 25C pA/C V RL 10 k V-suffix device nA VCC - 1.5 22 RL = 2 k Non-V device 50 0 to VCC - 2 VCC = MAX, Non-V device VID = -1 V, VO = 200 mV 50 0 to VCC - 1.5 Low-level output voltage Output current V/C -500 VOL IO mV 150 Full range VCC = 5 V to MAX 2 300 Full range 25C 7 4 Full range RL 10 k VOH 1 25C V-suffix device UNIT 10 25C A-suffix devices Non-V device IIO 3 Full range MAX POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLOS068P - JUNE 1976 - REVISED SEPTEMBER 2004 electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) PARAMETER VIO Input offset voltage aV Average temperature coefficient of input offset voltage IO IIO Input offset current aI Average temperature coefficient of input offset current IO IIB Input bias current VICR Common-mode input voltage range VOH VOL AVD CMRR kSVR VO1/VO2 IO High-level output voltage TEST CONDITIONS VCC = 5 V to 30 V, VIC = VICR(min), VO = 1.4 V VO = 1.4 V VO = 1.4 V ICC Supply current (two amplifiers) Full range 4 LM258A TYP 2 MAX UNIT 3 4 Full range 7 15* 7 15 25C 2 10 2 15 30 Full range 10 25C -15 30 200 10 -50 -15 -100 25C RL = 2 k Full range 26 RL 10 k Full range 27 Full range VCC = 30 V MIN mV VCC = 30 V VCC = 15 V, VO = 1 V to 11 V, RL 2 k IOS 2 0 to VCC - 1.5 0 to VCC - 2 VCC - 1.5 RL 2 k MAX 25C 25C Large-signal differential voltage amplification Common-mode rejection ratio Short-circuit output current LM158A TYP Full range RL 10 k Output current MIN Full range Low-level output voltage Supply-voltage rejection ratio (VDD/VIO) Crosstalk attenuation TA Full range 28 5 -80 -100 0 to VCC - 1.5 0 to VCC - 2 VCC - 1.5 26 27 20 100 200 nA pA/C nA V V 28 5 50 V/C 20 mV 25C 50 100 Full range 25 25C 70 80 70 80 dB 25C 65 100 65 100 dB 120 dB V/mV f = 1 kHz to 20 kHz 25C VCC = 15 V, VID = 1 V, VO = 0 25C -20 Full range -10 25C 10 Full range 5 25C 12 25 120 -30 -60 -20 -30 -60 Source VCC = 15 V, Sink VID = -1 V, VO = 15 VID = -1 V, VO = 200 mV VCC at 5 V, GND at -5 V, VO = 0 VO = 2.5 V, No load VCC = MAX, VO = 0.5 V, No load -10 mA 20 10 20 5 30 12 A 30 25C 40 60 40 60 Full range 0.7 1.2 0.7 1.2 Full range 1 2 1 2 mA mA *On products compliant to MIL-PRF-38535, this parameter is not production tested. All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified. MAX VCC for testing purposes is 26 V for LM2904 and 30 V for others. Full range is -55C to 125C for LM158A, -25C to 85C for LM258A, and 0C to 70C for LM358A. All typical values are at TA = 25C. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SLOS068P - JUNE 1976 - REVISED SEPTEMBER 2004 electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) TEST CONDITIONS PARAMETER VCC = 5 V to 30 V, VIC = VICR(min), VO = 1.4 V VIO Input offset voltage aV Average temperature coefficient of input offset voltage IO IIO Input offset current aI Average temperature coefficient of input offset current IO IIB VO = 1.4 V Input bias current TA VOL Low-level output voltage 3 5 Full range 7 20 25C 2 30 75 Full range 10 300 25C -15 -100 Full range VCC = 30 V RL 2 k High-level output voltage 2 25C Full range VOH MAX Full range VO = 1.4 V Common-mode input voltage range LM358A TYP Full range 25C VICR MIN 25C VCC = 30 V RL = 2 k Full range RL 10 k Full range RL 10 k -200 0 to VCC - 1.5 V/C nA pA/C nA VCC - 1.5 26 V 27 28 25C 25 100 Full range 15 5 20 mV AVD Large-signal differential voltage amplification CMRR Common-mode rejection ratio 25C 65 80 dB kSVR Supply-voltage rejection ratio (VDD/VIO) 25C 65 100 dB VO1/VO2 Crosstalk attenuation IO IOS ICC Output current Short-circuit output current Supply current (two amplifiers) VCC = 15 V, VO = 1 V to 11 V, RL 2 k mV V 0 to VCC - 2 Full range UNIT f = 1 kHz to 20 kHz 25C VCC = 15 V, VID = 1 V, VO = 0 25C -20 Full range -10 25C 10 Full range 5 VCC = 15 V, VID = -1 V, VO = 15 V V/mV 120 -30 dB -60 Source mA 20 Sink A VID = -1 V, VO = 200 mV VCC at 5 V, GND at -5 V, VO = 0 25C 30 25C 40 60 VO = 2.5 V, No load VCC = MAX, VO = 0.5 V, No load Full range 0.7 1.2 Full range 1 2 mA mA All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified. MAX VCC for testing purposes is 26 V for LM2904 and 30 V for others. Full range is -55C to 125C for LM158A, -25C to 85C for LM258A, and 0C to 70C for LM358A. All typical values are at TA = 25C. 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLOS068P - JUNE 1976 - REVISED SEPTEMBER 2004 operating conditions, VCC = 15 V, TA = 25C PARAMETER TEST CONDITIONS TYP UNIT SR Slew rate at unity gain RL = 1 M, CL = 30 pF, VI = 10 V (see Figure 1) 0.3 V/s B1 Unity-gain bandwidth RL = 1 M, CL = 20 pF (see Figure 1) 0.7 MHz Equivalent input noise voltage RS = 100 , VI = 0 V, f = 1 kHz (see Figure 2) 40 nV/Hz Vn VCC+ - VI VO + CL VCC- RL Figure 1. Unity-Gain Amplifier 900 VCC+ 100 - VI = 0 V RS VO + VCC- Figure 2. Noise-Test Circuit POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 PACKAGE OPTION ADDENDUM www.ti.com 4-Mar-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 5962-87710012A ACTIVE LCCC FK 20 1 None 5962-8771001PA ACTIVE CDIP JG 8 1 None 5962-87710022A ACTIVE LCCC FK 20 1 None 5962-8771002PA ACTIVE CDIP JG 8 1 None LM158AFKB ACTIVE LCCC FK 20 1 None Lead/Ball Finish MSL Peak Temp (3) POST-PLATE Level-NC-NC-NC A42 SNPB Level-NC-NC-NC POST-PLATE Level-NC-NC-NC A42 SNPB Level-NC-NC-NC POST-PLATE Level-NC-NC-NC LM158AJG ACTIVE CDIP JG 8 1 None A42 SNPB Level-NC-NC-NC LM158AJGB ACTIVE CDIP JG 8 1 None A42 SNPB Level-NC-NC-NC LM158FKB ACTIVE LCCC FK 20 1 None POST-PLATE Level-NC-NC-NC LM158JG ACTIVE CDIP JG 8 1 None A42 SNPB Level-NC-NC-NC LM158JGB ACTIVE CDIP JG 8 1 None A42 SNPB Level-NC-NC-NC LM258AD ACTIVE SOIC D 8 75 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM LM258ADGKR ACTIVE MSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1YEAR LM258ADR ACTIVE SOIC D 8 2500 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM LM258AP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC LM258D ACTIVE SOIC D 8 75 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM LM258DGKR ACTIVE MSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1YEAR LM258DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM258P ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC LM2904AVQDR ACTIVE SOIC D 8 2500 Pb-Free (RoHS) CU NIPDAU Level-2-250C-1 YEAR/ Level-1-235C-UNLIM LM2904AVQPWR ACTIVE TSSOP PW 8 2000 None CU NIPDAU Level-1-250C-UNLIM LM2904D ACTIVE SOIC D 8 75 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM LM2904DGKR ACTIVE MSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1YEAR LM2904DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM2904P ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC LM2904PSR ACTIVE SO PS 8 2000 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM LM2904PW ACTIVE TSSOP PW 8 150 Pb-Free (RoHS) CU NIPDAU Level-1-250C-UNLIM LM2904PWLE OBSOLETE TSSOP PW 8 None Call TI LM2904PWR ACTIVE TSSOP PW 8 Pb-Free (RoHS) CU NIPDAU LM2904QD OBSOLETE SOIC D 8 None Call TI LM2904QDR OBSOLETE SOIC D 8 Pb-Free (RoHS) CU NIPDAU 2000 Addendum-Page 1 Call TI Level-1-250C-UNLIM Call TI Level-2-250C-1 YEAR/ Level-1-235C-UNLIM PACKAGE OPTION ADDENDUM www.ti.com 4-Mar-2005 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty LM2904QP OBSOLETE PDIP P 8 LM2904VQDR ACTIVE SOIC D 8 2500 LM2904VQPWR ACTIVE TSSOP PW 8 LM358AD ACTIVE SOIC D 8 LM358ADGKR ACTIVE MSOP DGK 8 LM358ADR ACTIVE SOIC D 8 LM358AP ACTIVE PDIP P 8 50 LM358APW ACTIVE TSSOP PW 8 LM358APWR ACTIVE TSSOP PW LM358D ACTIVE SOIC LM358DGKR ACTIVE LM358DR Lead/Ball Finish MSL Peak Temp (3) None Call TI Pb-Free (RoHS) CU NIPDAU Call TI Level-2-250C-1 YEAR/ Level-1-235C-UNLIM 2000 None CU NIPDAU Level-1-250C-UNLIM 75 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1YEAR 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC 150 Pb-Free (RoHS) CU NIPDAU Level-1-250C-UNLIM 8 2000 Pb-Free (RoHS) CU NIPDAU Level-1-250C-UNLIM D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1YEAR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LM358P ACTIVE PDIP P 8 CU NIPDAU Level-NC-NC-NC LM358PSLE OBSOLETE SO PS 8 LM358PSR ACTIVE SO PS LM358PW ACTIVE TSSOP LM358PWLE OBSOLETE LM358PWR ACTIVE 50 Pb-Free (RoHS) None Call TI 8 2000 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM PW 8 150 Pb-Free (RoHS) CU NIPDAU Level-1-250C-UNLIM TSSOP PW 8 None Call TI TSSOP PW 8 Pb-Free (RoHS) CU NIPDAU 2000 Call TI Call TI Level-1-250C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. None: Not yet available Lead (Pb-Free). Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens, including bromine (Br) or antimony (Sb) above 0.1% of total product weight. (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 4-Mar-2005 provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 MECHANICAL DATA MCER001A - JANUARY 1995 - REVISED JANUARY 1997 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE 0.400 (10,16) 0.355 (9,00) 8 5 0.280 (7,11) 0.245 (6,22) 1 0.063 (1,60) 0.015 (0,38) 4 0.065 (1,65) 0.045 (1,14) 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0-15 0.100 (2,54) 0.014 (0,36) 0.008 (0,20) 4040107/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification. Falls within MIL STD 1835 GDIP1-T8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MLCC006B - OCTOBER 1996 FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 28 TERMINAL SHOWN 18 17 16 15 14 13 NO. OF TERMINALS ** 12 19 11 20 10 A B MIN MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.739 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 0.938 (23,83) 0.962 (24,43) 0.850 (21,6) 0.858 (21,8) 84 1.141 (28,99) 1.165 (29,59) 1.047 (26,6) 1.063 (27,0) B SQ A SQ 25 5 26 27 28 1 2 3 4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 4040140 / D 10/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MPDI001A - JANUARY 1995 - REVISED JUNE 1999 P (R-PDIP-T8) PLASTIC DUAL-IN-LINE 0.400 (10,60) 0.355 (9,02) 8 5 0.260 (6,60) 0.240 (6,10) 1 4 0.070 (1,78) MAX 0.325 (8,26) 0.300 (7,62) 0.020 (0,51) MIN 0.015 (0,38) Gage Plane 0.200 (5,08) MAX Seating Plane 0.010 (0,25) NOM 0.125 (3,18) MIN 0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.430 (10,92) MAX 0.010 (0,25) M 4040082/D 05/98 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001 For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C - JANUARY 1995 - REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated