DATASHEET ICS664-02 PECL DIGITAL VIDEO CLOCK SOURCE Description Features The ICS664-02 provides clock generation and conversion for clock rates commonly needed in HDTV digital video equipment. The ICS664-02 uses the latest Phase-Locked Loop (PLL) technology to provide excellent phase noise and long-term jitter performance for superior synchronization and S/N ratio. * * * * * * * * * * For audio sampling clocks generated from 27 MHz, use the ICS661. Please contact ICS if you have a requirement for an input and output frequency not included in this document. ICS can rapidly modify this product to meet special requirements. Packaged in 16-pin TSSOP Available in Pb (lead) free package Clock or crystal input Low phase noise Low jitter Exact (0 ppm) multiplication ratios Power-down control Improved phase noise over ICS660 Differential outputs Supports SMTE 292M HD-SDI standard for HDTV broadcast Block Diagram VDD (P2) VDD (P3) VDDO VDD (P10) X2 Crystal Oscillator X1/REFIN SELIN S3:0 PLL Clock Synthesis CLK CLK 4 GND (P6) IDTTM / ICSTM PECL DIGITAL VIDEO CLOCK SOURCE GND (P5) 1 GND (P12) ICS664-02 REV C 062304 ICS664-02 PECL DIGITAL VIDEO CLOCK SOURCE PECL CLOCK SYNTHESIZER Pin Assignment Output Clock Selection Table X1/REFIN 1 16 X2 VDD 2 15 VDDO VDD 3 14 CLK S0 4 13 Input Frequency (MHz) Output Frequency (MHz) S3 S2 S1 S0 0 0 0 0 0 0 0 1 Pass thru CLK 0 0 1 0 27 74.25 0 1 1 27 74.175824 Power down Input Freq GND 5 12 GND 0 GND 6 0 1 0 0 13.5 74.25 11 SELIN 0 1 0 1 13.5 74.175824 S3 7 10 VDD 0 1 1 0 RESERVED RESERVED S2 8 9 0 1 1 1 RESERVED RESERVED 1 0 0 0 74.25 54 1 0 0 1 74.175824 54 1 0 1 0 RESERVED RESERVED 1 0 1 1 RESERVED RESERVED 1 1 0 0 54 74.25 1 1 0 1 54 74.175824 1 1 1 0 54 13.5 1 1 1 1 27 13.5 S1 16-pin 4.40 mil body, 0.65 mm pitch TSSOP Pin Descriptions Pin Number Pin Name Pin Type 1 X1/REFIN Input Connect this pin to a crystal or clock input 2 VDD Power Power supply for crystal oscillator. 3 VDD Power Power supply for PLL. 4 S0 Input Output frequency selection. Determines output frequency per table above. On chip pull-up. 5 GND Power Ground for PLL. 6 GND Power Ground for oscillator. 7 S3 Input Output frequency selection. Determines output frequency per table above. On chip pull-up. 8 S2 Input Output frequency selection. Determines output frequency per table above. On chip pull-up. 9 S1 Input Output frequency selection. Determines output frequency per table above. On chip pull-up. 10 VDD Power Power supply. 11 SELIN Input Low for clock input, high for crystal. On chip pull-up. 12 GND Power Ground for output stage 13 CLK Output Complimentary clock output. 14 CLK Output Clock output. 15 VDDO Power Power supply for output stage. 16 X2 Input Connect this pin to a crystal. Leave open if using a clock input. Pin Description IDTTM / ICSTM PECL DIGITAL VIDEO CLOCK SOURCE 2 ICS664-02 REV C 062304 ICS664-02 PECL DIGITAL VIDEO CLOCK SOURCE PECL CLOCK SYNTHESIZER Application Information Termination Resistor to ground. These capacitors are used to adjust the stray capacitance of the board to match the nominally required crystal load capacitance. To reduce possible noise pickup, use very short PCB traces (and no vias) been the crystal and device. Terminate the outputs with 50 to ground. Decoupling Capacitors As with any high-performance mixed-signal IC, the ICS664-02 must be isolated from system power supply noise to perform optimally. The value of the load capacitors can be roughly determined by the formula C = 2(CL - 6) where C is the load capacitor connected to X1 and X2, and CL is the specified value of the load capacitance for the crystal. A typical crystal CL is 18 pF, so C = 2(18 - 6) = 24 pF. Because these capacitors adjust the stray capacitance of the PCB, check the output frequency using your final layout to see if the value of C should be changed. Decoupling capacitors of 0.01F must be connected between each VDD and the PCB ground plane. To further guard against interfering system supply noise, the ICS664-02 should use one common connection to the PCB power plane as shown in the diagram on the next page. The ferrite bead and bulk capacitor help reduce lower frequency noise in the supply that can lead to output clock phase modulation. PCB Layout Recommendations For optimum device performance and lowest output phase noise, the following guidelines should be observed. Recommended Power Supply Connection for Optimal Device Performance 1) Each 0.01F decoupling capacitor should be mounted on the component side of the board as close to the VDD pin as possible. No vias should be used between decoupling capacitor and VDD pin. The PCB trace to VDD pin should be kept as short as possible, as should the PCB trace to the ground via. Distance of the ferrite bead and bulk decoupling from the device is less critical. V D D P in C onnection to 3.3V P ow er P lane Ferrite Bead B ulk D ecoupling C apacitor (such as 1 F Tantalum ) 0.01 V D D P in V D D P in 2) The external crystal should be mounted next to the device with short traces. The X1 and X2 traces should not be routed next to each other with minimum spaces, instead they should be separated and away from other traces. F D ecoupling C apacitors 3) To minimize EMI, and obtain the best signal integrity, the 50 series termination resistor should be placed close to the clock output. All power supply pins must be connected to the same voltage, except VDDO, which may be connected to a lower voltage in order to change the output level. 4) An optimum layout is one with all components on the same side of the board, minimizing vias through other signal layers (the ferrite bead and bulk decoupling capacitor can be mounted on the back). Other signal traces should be routed away from the ICS664-02. This includes signal traces just underneath the device, or on layers adjacent to the ground plane layer used by the device. To achieve the absolute minimum jitter, power the part with a dedicated LDO regulator, which will provide high isolation from power supply noise. Many companies produce very small, inexpensive regulators; an example is the National Semiconductor LP2985. Crystal Load Capacitors If a crystal is used, the device crystal connections should include pads for capacitors from X1 to ground and from X2 IDTTM / ICSTM PECL DIGITAL VIDEO CLOCK SOURCE 3 ICS664-02 REV C 062304 ICS664-02 PECL DIGITAL VIDEO CLOCK SOURCE PECL CLOCK SYNTHESIZER Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS664-02. These ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 5.5 V All Inputs and Outputs -0.5V to VDD+0.5 V Ambient Operating Temperature 0 to +70 C Storage Temperature -65 to +150 C Junction Temperature 125 C Soldering Temperature 260 C Recommended Operation Conditions Parameter Min. Ambient Operating Temperature Power Supply Voltage (measured in respect to GND) Typ. Max. Units 0 +70 C +3.0 +3.6 V DC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V 10%, Ambient Temperature 0 to +70 C Parameter Symbol Conditions VDD Operating Voltage Standby Supply Current IDD 2.5 No Load IDDPD Input High Voltage VIH Input Low Voltage VIL Output High Voltage VOH Output Low Voltage VOL Input Capacitance CIN Internal Pull-up Resistor RPU IDTTM / ICSTM PECL DIGITAL VIDEO CLOCK SOURCE Typ. 3.0 VDDO Supply Current Min. Max. Units 3.6 V VDD mA 75 A 2 input pins 4 V 25 V 0.8 V VDDO-1.5 VDDO-1.1 V VDDO-2.0 VDDO-1.8 V 7 pF 120 k ICS664-02 REV C 062304 ICS664-02 PECL DIGITAL VIDEO CLOCK SOURCE PECL CLOCK SYNTHESIZER AC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V 10%, Ambient Temperature 0 to +70 C Parameter Symbol Conditions Min. Typ. Crystal Frequency Max. Units 28 MHz Output Clock Rise Time tOR 20% to 80%, 15 pF load 1.5 ns Output Clock Fall Time tOF 80% to 20%, 15 pF load 1.5 ns Output Duty Cycle tOD at VDD/2, 15 pF load 60 % Power-up Time tPU Inputs out of PD state to clocks stable 10 ms Power-down Time tPD Inputs in PD state to clocks off 1 s 40 Jitter, Short term 49 to 51 70 ps p-p Jitter, Long term 10 s delay 300 ps p-p Single Sideband Phase Noise 10 kHz offset -120 dBc 0 ppm Actual Mean Frequency Error versus Target Thermal Characteristics Parameter Thermal Resistance Junction to Ambient Thermal Resistance Junction to Case IDTTM / ICSTM PECL DIGITAL VIDEO CLOCK SOURCE Symbol Conditions Min. Typ. Max. Units JA Still air 78 C/W JA 1 m/s air flow 70 C/W JA 3 m/s air flow 68 C/W 37 C/W JC 5 ICS664-02 REV C 062304 ICS664-02 PECL DIGITAL VIDEO CLOCK SOURCE PECL CLOCK SYNTHESIZER Package Outline and Package Dimensions (16-pin TSSOP, 4.40 mm Body, 0.65 mm Pitch) Package dimensions are kept current with JEDEC Publication No. 95, MO-153 Millimeters 16 Symbol E1 A A1 A2 b C D E E1 e L aaa E IN D EX AR EA 1 2 D A 2 Min Inches Max -1.20 0.05 0.15 0.80 1.05 0.19 0.30 0.09 0.20 4.90 5.1 6.40 BASIC 4.30 4.50 0.65 Basic 0.45 0.75 0 8 -0.10 Min Max -0.047 0.002 0.006 0.032 0.041 0.007 0.012 0.0035 0.008 0.193 0.201 0.252 BASIC 0.169 0.177 0.0256 Basic 0.018 0.030 0 8 -0.004 A A 1 c -C e b S E A TIN G P LA N E L aaa C Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature ICS664G-02 664G-02 Tubes 16-pin TSSOP 0 to +70 C ICS664G-02TR 664G-02 Tape and Reel 16-pin TSSOP 0 to +70 C ICS664G-02LF 664G-02L Tubes 16-pin TSSOP 0 to +70 C ICS664G-02LFTR 664G-02L Tape and Reel 16-pin TSSOP 0 to +70 C "LF" denotes Pb (lead) free package. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. IDTTM / ICSTM PECL DIGITAL VIDEO CLOCK SOURCE 6 ICS664-02 REV C 062304 ICS664-02 PECL DIGITAL VIDEO CLOCK SOURCE PECL CLOCK SYNTHESIZER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 <product line email> <product line phone> Corporate Headquarters Asia Pacific and Japan Europe Integrated Device Technology, Inc. 6024 Silver Creek Valley Road San Jose, CA 95138 United States 800 345 7015 +408 284 8200 (outside U.S.) Integrated Device Technology Singapore (1997) Pte. Ltd. Reg. No. 199707558G 435 Orchard Road #20-03 Wisma Atria Singapore 238877 +65 6 887 5505 IDT Europe, Limited Prime House Barnett Wood Lane Leatherhead, Surrey United Kingdom KT22 7DE +44 1372 363 339 (c) 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA