SOLID TANTALUM ELECTROLYTIC CAPACITORS F97 Resin-molded Chip, High Reliability (High temperature / moisture resistance) Series Specifications Item --55 ~ +125C (Rated temperature : 85C.) Capacitance Tolerance 20%, 10% (at 120Hz) Dissipation Factor ~1.5 F 4% Max. 2.2 ~68 F 6% Max. (at 120Hz) 100 F~ 8% Max. Leakage Current * After 1 minute' s application of rated voltage,leakage current at 20C is not more than 0.01CV or 0.5A, whichever is greater. * After 1 minute' s application of rated voltage,leakage current at 85C is not more than 0.1CV or 5A,whichever is greater. * After 1 minute' s application of derated voltage,leakage current at 125C is not more than 0.125CV or 6.3A,whichever is greater. Capacitance Change by Temperature +15% Max. (at +125C) +10% Max. (at +85C) --10% Max. (at --55C) Damp Heat At 85C, 85% R.H.,For 1000 hours (No voltage applied) Capacitance Change * * * * * * Within 10% of initial value Dissipation Factor * * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * 125% or less of initial specified value Load Humidity After 500 hour' s application of rated voltage in series with a 33 resistor at 60C,90~95% R.H.,capacitors meet the characteristics requirements listed below. Capacitance Change * * * * * * Within 10% of initial value Dissipation Factor * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * 125% or less of initial specified value Temperature Cycles At --55C / +125C,For 30 minutes each,1000 cycles Capacitance Change * * * * * * Within 5% of initial value Dissipation Factor * * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * * Initial specified value or less Resistance to Soldering Heat At 260C,reflowing capacitors for 10 seconds Max. Capacitance Change * * * * * * Within 5% of initial value Dissipation Factor * * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * * Initial specified value or less Solderability After immersing capacitors completely into a solder pot at 245C for 2~3 seconds,more than 3/4 of their electrode area shall remain covered with new solder. Type numbering system (Example : 16V 3.3 F) 1 2 3 4 5 6 7 8 9 10 F 9 7 1 C 3 3 5 M B 11 Taping code (Refer to page 213 for details) Case code Capacitance tolerance Rated Capacitance Rated voltage Series Drawing A * B Case C * N Case L W1 L W1 H H W2 S W2 S S S Dimensions Case code 3.2 3.5 6.0 7.3 A B C N Surge (mm) L W1 1.6 2.8 3.2 4.3 0.2 0.2 0.2 0.2 W2 1.2 2.2 2.2 2.4 0.2 0.2 0.2 0.2 H 1.6 1.9 2.5 2.8 0.1 0.1 0.1 0.1 S 0.8 0.2 0.8 0.2 1.3 0.2 1.3 0.2 0.2 0.2 0.2 0.2 Endurance Marking B Case C Case 10 16r 3.3 16r C105 N Case 47 10r A Case Shear Test Month code Rated voltage (Voltage code) Rated Capacitance (Capacitance code ) Rated voltage (V) Rated Capacitance (F) Standard ratings V Code 4 0G 6.3 0J 10 1A 16 1C 20 1D 25 1E 35 1V 0.1 104 A 0.15 154 A 0.22 234 A 0.33 334 0.47 474 0.68 684 1 105 1.5 155 2.2 225 A A 3.3 335 A A A B 4.7 475 A A B B 6.8 685 A B B 10 106 B B B 15 156 B B C 22 226 B C 33 336 C C 47 476 68 686 100 107 N 150 157 N A A A A C C * C N * N * B A B B C A A N After Applying the pressure load of 5N for 10 1 seconds horizontally to the center of capacitor side body which has no electrode and has been 5N (0.51kg * f) soldered beforehand on an aluminum For 10 1 seconds substrate,there shall be found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of the capacitor, the pressure strength is applied with a 20 specified jig at the center of the R230 substrate so that the substrate may bend by 1mm as illustrated. Then,there shall be found no 45 45 remarkable abnormality on the capacitor terminals. As for the surge and derated voltage at 125C, refer to page 212 for details. B B C C A Terminal Strength After application of surge in series with a 33 resistor at the rate of 30 seconds ON, 30 seconds OFF,for 1000 successive test cycles at 85C,capacitors meet the characteristics requirements listed below. Capacitance Change * * * * * * Within 5% of initial value Dissipation Factor * * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * * Initial specified value or less After 2000 hours' application of rated voltage in series with a 3 resistor at 85C,or derated voltage in series with a 3 resistor at 125C,capacitors meet the characteristic requirements listed below. Capacitance Change * * * * * * Within 10% of initial value Dissipation Factor * * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * * Initial specified value or less 1mm Cap. (F) Performance Characteristics Category Temperature Range C B C C N C C N C C N N C N N N N N N N N CAT.8100S