Product Specification PE4302 50 RF Digital Attenuator 6-bit, 31.5 dB, DC - 4.0 GHz Product Description The PE4302 is a high linearity, 6-bit RF Digital Step Attenuator (DSA) covering a 31.5 dB attenuation range in 0.5 dB steps. This 50-ohm RF DSA provides both parallel and serial CMOS control interface operates on a single 3-volt supply and maintains high attenuation accuracy over frequency and temperature. It also has a unique control interface that allows the user to select an initial attenuation state at power-up. The PE4302 exhibits very low insertion loss and low power consumption. This functionality is delivered in a 4x4 mm QFN footprint. Features * Attenuation: 0.5 dB steps to 31.5 dB The PE4302 is manufactured on Peregrine's UltraCMOSTM process, a patented variation of silicon-on-insulator (SOI) technology on a sapphire substrate, offering the performance of GaAs with the economy and integration of conventional CMOS. * Single-supply operation Figure 1. Functional Schematic Diagram Figure 2. Package Type * Flexible parallel and serial programming interfaces * Unique power-up state selection * Positive CMOS control logic * High attenuation accuracy and linearity over temperature and frequency * Very low power consumption * 50 impedance * Packaged in a 20 lead 4x4mm QFN 4x4 mm 20-Lead QFN Switched Attenuator Array RF Input RF Output Parallel Control 6 Serial Control 3 Power-Up Control 2 Control Logic Interface Table 1. Electrical Specifications @ +25C, VDD = 3.0 V Parameter Test Conditions Frequency Operation Frequency Any Bit or Bit Combination 1 dB Compression3 Input IP31,2 Two-tone inputs +18 dBm Return Loss Switching Speed Typical DC Insertion Loss2 Attenuation Accuracy Minimum 50% control to 0.5 dB of final value Maximum Units 4000 MHz DC - 2.2 GHz - 1.5 1.75 dB DC 1.0 GHz 1.0 < 2.2 GHz - - (0.10 + 3% of atten setting) (0.15 + 5% of atten setting) dB dB 1 MHz - 2.2 GHz 30 34 - dBm 1 MHz - 2.2 GHz - 52 - dBm DC - 2.2 GHz 15 20 - dB - - 1 s Notes: 1. Device Linearity will begin to degrade below 1 Mhz 2. See Max input rating in Table 3 & Figures on Pages 2 to 4 for data across frequency. 3. Note Absolute Maximum in Table 3. Document No. 70-0056-04 www.psemi.com (c)2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 11 PE4302 Product Specification Typical Performance Data @ 25C, VDD = 3.0 V Figure 3. Insertion Loss Figure 4. Attenuation at Major steps 0 35 31.5dB 30 -1 Attenuation (dB) Insertion Loss (dB) -40C 25C 85C -3 -4 Normalized to Insertion Loss 25 -2 20 16dB 15 2dB 10 -5 1dB 0.5dB 8dB 4dB 5 0 -6 0 500 1000 1500 2000 2500 3000 3500 0 4000 500 1000 Figure 5. Input Return Loss at Major Attenuation Steps 3000 3500 4000 -10 -20 -20 3500 4000 S22 (dB) -10 S11 (dB) 0 16dB -30 31.5dB 31.5dB -40 -50 -50 0 500 1000 1500 2000 2500 3000 3500 RF Frequency (MHz) (c)2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 11 2500 Figure 6. Output Return Loss at Major Attenuation Steps 0 -40 2000 RF Frequency (MHz) RF Frequency (MHz) -30 1500 4000 0 500 1000 1500 2000 2500 3000 RF Frequency (MHz) Document No. 70-0056-04 UltraCMOSTM RFIC Solutions PE4302 Product Specification Typical Performance Data @ 25C, VDD = 3.0 V Figure 7. Attenuation Error Vs. Frequency Figure 8. Attenuation Error Vs. Attenuation Setting 2 0.5 0 31.5 (dB) -2 Attenuation Error (dB) Attenuation Error (dB) 0 -4 -6 10Mhz 500Mhz 1000Mhz -0.5 1500Mhz 2000Mhz -1 2200Mhz -8 -10 -1.5 0 500 1000 1500 2000 2500 3000 3500 4000 0 5 10 RF Frequency (MHz) 20 25 30 35 40 Attenuation Setting (dB) Figure 9. Attenuation Error Vs. Attenuation Setting Figure 10. Attenuation Error Vs. Attenuation Setting 0.6 0.4 0.2 0.4 10Mhz, -40C 0.2 500Mhz, -40C 0 10Mhz, 25C 500Mhz, 25C -0.2 0 Attenuation Error (dB) Attenuation Error (dB) 15 1000Mhz, -40C -0.2 1000Mhz, 25C -0.4 1500Mhz, -40C -0.6 1000Mhz, 85C 10Mhz, 85C -0.4 1490Mhz, 25C -0.8 500Mhz, 85C 1490Mhz, 85C -0.6 -1 0 5 10 15 20 25 30 35 40 0 Attenuation Setting (dB) 5 10 15 20 25 30 35 40 Attenuation Setting (dB) Note: Positive attenuation error indicates higher attenuation than target value Document No. 70-0056-04 www.psemi.com (c)2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 11 PE4302 Product Specification Typical Performance Data @ 25C, VDD = 3.0 V Figure 11. Attenuation Error Vs. Frequency Figure 12. Input IP3 Vs. Frequency 0.5 60 2200Mhz, -40C 55 0 50 Input IP3 (dBm) Attenuation Error (dB) 2000Mhz, -40C 2200Mhz, 25C -0.5 2000Mhz, 25C 45 40 35 2200Mhz, 85C -1 30 0dB 1dB 4dB 16dB .5dB 2dB 8dB 31.5dB 2000Mhz, 85C 25 -1.5 20 0 5 10 15 20 25 30 35 40 Attenuation Setting (dB) 0 500 1000 1500 2000 2500 3000 RF Frequency (MHz) Figure 13. Input 1 dB Compression 40 1dB Compression (dBm) 35 30 25 20 0dB 1dB 4dB 16dB 0.5dB 2dB 8dB 31.5dB 15 10 0 500 1000 1500 2000 2500 3000 RF Frequency (MHz) Note: Positive attenuation error indicates higher attenuation than target value (c)2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 11 Document No. 70-0056-04 UltraCMOSTM RFIC Solutions PE4302 Product Specification Table 3. Absolute Maximum Ratings C4 VDD 16 C2 Symbol 17 GND 18 19 20 C1 C0.5 Figure 14. Pin Configuration (Top View) Input power (50) +30 dBm ESD voltage (Human Body Model) 500 V PIN Data 3 13 P/S Clock 4 12 Vss/GND LE 5 11 GND 6 7 8 9 10 PUP1 PUP2 VDD GND VESD Exceeding absolute maximum ratings may cause permanent damage. Operation should be restricted to the limits in the Operating Ranges table. Operation between operating range maximum and absolute maximum for extended periods may reduce reliability. Table 4. Operating Ranges Table 2. Pin Descriptions Parameter Min Typ Max Units VDD Power Supply Voltage 2.7 3.0 3.3 V 100 A Pin No. Pin Name 1 C16 Attenuation control bit, 16dB (Note 4). 2 RF1 RF port (Note 1). IDD Power Supply Current 3 Data Serial interface data input (Note 4). Digital Input High 4 Clock Serial interface clock input. Digital Input Low 5 LE Latch Enable input (Note 2). 6 VDD Power supply pin. 7 PUP1 Power-up selection bit, MSB. 8 PUP2 Power-up selection bit, LSB. GND V C RF2 11 V 150 14 VDD 4.0 -65 2 GND -0.3 Storage temperature range TST RF1 VDD Power supply voltage -0.3 C8 9 Units Voltage on any DC input 15 10 Max VI 1 Exposed Solder Pad Min VDD+ 0.3 C16 20-lead QFN 4x4mm Parameter/Conditions Description Power supply pin. Ground connection. Ground connection. Negative supply voltage or GND connection(Note 3) 12 Vss/GND 13 P/S Parallel/Serial mode select. 14 RF2 RF port (Note 1). 15 C8 Attenuation control bit, 8 dB. 16 C4 Attenuation control bit, 4 dB. 17 C2 Attenuation control bit, 2 dB. 18 GND 19 C1 Ground connection. Attenuation control bit, 1 dB. 20 C0.5 Attenuation control bit, 0.5 dB. Paddle GND Ground for proper operation Note 1: Both RF ports must be held at 0 VDC or DC blocked with an external series capacitor. 2: Latch Enable (LE) has an internal 100 kresistor to VDD. 3: Connect pin 12 to GND to enable internal negative voltage generator. Connect pin 12 to VSS (-VDD) to bypass and disable internal negative voltage generator. 4. Place a 10 kresistor in series, as close to pin as possible to avoid frequency resonance. Document No. 70-0056-04 www.psemi.com Digital Input Leakage Input Power Temperature range V 0.7xVDD -40 0.3xVDD V 1 A +24 dBm 85 C Exposed Solder Pad Connection The exposed solder pad on the bottom of the package must be grounded for proper device operation. Electrostatic Discharge (ESD) Precautions When handling this UltraCMOSTM device, observe the same precautions that you would use with other ESDsensitive devices. Although this device contains circuitry to protect it from damage due to ESD, precautions should be taken to avoid exceeding the rate specified in Table 3. Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOSTM devices are immune to latch-up. Switching Frequency The PE4302 has a maximum 25 kHz switching rate. Resistor on Pin 1 & 3 A 10 k resistor on the inputs to Pin 1 & 3 (see Figure 16) will eliminate package resonance between the RF input pin and the two digital inputs. Specified attenuation error versus frequency performance is dependent upon this condition. (c)2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 5 of 11 PE4302 Product Specification Programming Options Parallel/Serial Selection Either a parallel or serial interface can be used to control the PE4302. The P/S bit provides this selection, with P/S=LOW selecting the parallel interface and P/S=HIGH selecting the serial interface. Parallel Mode Interface The parallel interface consists of five CMOScompatible control lines that select the desired attenuation state, as shown in Table 5. The parallel interface timing requirements are defined by Figure 18 (Parallel Interface Timing Diagram), Table 9 (Parallel Interface AC Characteristics), and switching speed (Table 1). For latched parallel programming the Latch Enable (LE) should be held LOW while changing attenuation state control values, then pulse LE HIGH to LOW (per Figure 18) to latch new attenuation state into device. For direct parallel programming, the Latch Enable (LE) line should be pulled HIGH. Changing attenuation state control values will change device state to new attenuation. Direct Mode is ideal for manual control of the device (using hardwire, switches, or jumpers). Table 5. Truth Table Attenuation C0.5 State P/S C16 C8 C4 C2 C1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0.5 dB 0 0 0 0 0 1 0 1 dB 0 0 0 0 1 0 0 2 dB 0 0 0 1 0 0 0 4 dB 0 0 1 0 0 0 0 8 dB 0 1 0 0 0 0 0 16 dB 0 1 1 1 1 1 1 31.5 dB Reference Loss Note: Not all 64 possible combinations of C0.5-C16 are shown in table Serial Interface The serial interface is a 6-bit serial-in, parallel-out shift register buffered by a transparent latch. It is controlled by three CMOS-compatible signals: Data, (c)2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 6 of 11 Clock, and Latch Enable (LE). The Data and Clock inputs allow data to be serially entered into the shift register, a process that is independent of the state of the LE input. The LE input controls the latch. When LE is HIGH, the latch is transparent and the contents of the serial shift register control the attenuator. When LE is brought LOW, data in the shift register is latched. The shift register should be loaded while LE is held LOW to prevent the attenuator value from changing as data is entered. The LE input should then be toggled HIGH and brought LOW again, latching the new data. The timing for this operation is defined by Figure 17 (Serial Interface Timing Diagram) and Table 8 (Serial Interface AC Characteristics). Power-up Control Settings The PE4302 always assumes a specifiable attenuation setting on power-up. This feature exists for both the Serial and Parallel modes of operation, and allows a known attenuation state to be established before an initial serial or parallel control word is provided. When the attenuator powers up in Serial mode (P/ S=1), the six control bits are set to whatever data is present on the six parallel data inputs (C0.5 to C16). This allows any one of the 64 attenuation settings to be specified as the power-up state. When the attenuator powers up in Parallel mode (P/ S=0) with LE=0, the control bits are automatically set to one of four possible values. These four values are selected by the two power-up control bits, PUP1 and PUP2, as shown in Table 6 (Power-Up Truth Table, Parallel Mode). Table 6. Parallel PUP Truth Table P/S LE PUP2 PUP1 Attenuation State 0 0 0 0 Reference Loss 0 0 1 0 8 dB 0 0 0 1 16 dB 0 0 1 1 31 dB 0 1 X X Defined by C0.5-C16 Note: Power up with LE=1 provides normal parallel operation with C0.5-C16, and PUP1 and PUP2 are not active. Document No. 70-0056-04 UltraCMOSTM RFIC Solutions PE4302 Product Specification Figure 15. Evaluation Board Layout Evaluation Kit Peregrine Specification 101/0112 The Digital Attenuator Evaluation Kit board was designed to ease customer evaluation of the PE4302 Digital Step Attenuator. J9 is used in conjunction with the supplied DC cable to supply VDD, GND, and -VDD. If use of the internal negative voltage generator is desired, then connect -VDD (Black banana plug) to ground. If an external -VDD is desired, then apply -3V. J1 should be connected to the parallel port of a PC with the supplied ribbon cable. The evaluation software is written to operate the DSA in serial mode, so Switch 7 (P/S) on the DIP switch SW1 should be ON with all other switches off. Using the software, enable or disable each attenuation setting to the desired combined attenuation. The software automatically programs the DSA each time an attenuation state is enabled or disabled. To evaluate the Power Up options, first disconnect the parallel ribbon cable from the evaluation board. The parallel cable must be removed to prevent the PC parallel port from biasing the control pins. Resistor on Pin 1 & 3 A 10 k resistor on the inputs to Pin 1 & 3 (Figure 16) will eliminate package resonance between the RF input pin and the two digital inputs. Specified attenuation error versus frequency performance is dependent upon this condition. Document No. 70-0056-04 www.psemi.com LE 5 VDD 16 C4 17 C2 18 GND 19 PS DATA U1 CLK LE Vss/GND GND CLK 4 MLPQ4X4 RFout VDD_D 10k RFin C8 GND 15 14 13 C8 J5 Z=50 Ohm PS 1 SMA 12 11 10 3 DATA C16 PUP2 2 C1 1 9 Z=50 Ohm PUP1 1 C2 C4 8 SMA C16 VDD 10k J4 C5 20 C0.5 C1 7 During power up with P/S=0 high and LE=0, the control bits are automatically set to one of four possible values presented through the PUP interface. These four values are selected by the two power-up control bits, PUP1 and PUP2, as shown in the Table 6. Peregrine Specification 102/0144 6 During power up with P/S=1 high and LE=0 or P/ S=0 low and LE=1, the default power-up signal attenuation is set to the value present on the six control bits on the six parallel data inputs (C0.5 to C16). This allows any one of the 64 attenuation settings to be specified as the power-up state. Figure 16. Evaluation Board Schematic PUP1 PUP2 100 pF Note: Resistors on pins 1 and 3 are required to avoid package resonance and meet error specifications over frequency. (c)2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 7 of 11 PE4302 Product Specification Figure 17. Serial Interface Timing Diagram Table 7. 6-Bit Attenuator Serial Programming Register Map LE Clock Data MSB tLESUP tSDHLD B4 B3 B2 B1 B0 C8 C4 C2 C1 C0.5 MSB (first in) LSB tSDSUP B5 C16 LSB (last in) tLEPW Figure 18. Parallel Interface Timing Diagram LE Parallel Data C16:C0.5 tPDSUP tLEPW tPDHLD Table 8. Serial Interface AC Characteristics Table 9. Parallel Interface AC Characteristics VDD = 3.0 V, -40 C < TA < 85 C, unless otherwise specified VDD = 3.0 V, -40 C < TA < 85 C, unless otherwise specified Symbol Parameter Min Max Unit 10 MHz fClk Serial data clock frequency (Note 1) tClkH Serial clock HIGH time 30 ns tClkL Serial clock LOW time 30 ns tLESUP LE set-up time after last clock falling edge 10 ns tLEPW LE minimum pulse width 30 ns tSDSUP Serial data set-up time before clock rising edge 10 ns tSDHLD Serial data hold time after clock falling edge 10 ns Symbol Parameter Min Max Unit tLEPW LE minimum pulse width 10 ns tPDSUP Data set-up time before rising edge of LE 10 ns tPDHLD Data hold time after falling edge of LE 10 ns Note: fClk is verified during the functional pattern test. Serial programming sections of the functional pattern are clocked at 10 MHz to verify fclk specification. (c)2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 8 of 11 Document No. 70-0056-04 UltraCMOSTM RFIC Solutions PE4302 Product Specification Figure 19. Package Drawing 4.00 INDEX AREA 2.00 X 2.00 2.00 4.00 2.00 -B- 0.25 C 0.80 -A- 0.10 C 0.08 C SEATING PLANE 0.20 REF -C- 2.00 TYP 0.55 2.00 TYP 0.50 0.020 EXPOSED PAD & TERMINAL PADS 1.00 0.435 1.00 10 11 2.00 4.00 0.435 0.18 6 5 0.18 1 15 20 DETAIL A EXPOSED PAD 16 DETAIL A 2 0.23 1 0.10 C A B 1. Dimension applies to metallized terminal and is measured between 0.25 and 0.30 from terminal tip. 2. Coplanarity applies to the exposed heat sink slug as well as the terminals. 3. Dimensions are in millimeters. Document No. 70-0056-04 www.psemi.com (c)2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 9 of 11 PE4302 Product Specification Figure 20. Marking Specifications 4302 YYWW ZZZZZ YYWW = Date Code ZZZZZ = Last five digits of PSC Lot Number Figure 21. Tape and Reel Drawing Table 10. Ordering Information Order Code Part Marking Description 4302-00 PE4302-EK PE4302-20MLP 4x4mm-EK Evaluation Kit 1 / Box 4302-51 4302 PE4302G-20MLP 4x4mm-75A Green 20-lead 4x4mm QFN 75 units / Tube 4302-52 4302 PE4302G-20MLP 4x4mm-3000C Green 20-lead 4x4mm QFN 3000 units / T&R (c)2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 10 of 11 Package Shipping Method Document No. 70-0056-04 UltraCMOSTM RFIC Solutions PE4302 Product Specification Sales Offices The Americas Peregrine Semiconductor Corporation Peregrine Semiconductor, Asia Pacific (APAC) 9380 Carroll Park Drive San Diego, CA 92121 Tel: 858-731-9400 Fax: 858-731-9499 Shanghai, 200040, P.R. China Tel: +86-21-5836-8276 Fax: +86-21-5836-7652 Europe Peregrine Semiconductor Europe Batiment Maine 13-15 rue des Quatre Vents F-92380 Garches, France Tel: +33-1-4741-9173 Fax : +33-1-4741-9173 Space and Defense Products Peregrine Semiconductor, Korea #B-2607, Kolon Tripolis, 210 Geumgok-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-943 South Korea Tel: +82-31-728-3939 Fax: +82-31-728-3940 Peregrine Semiconductor K.K., Japan Teikoku Hotel Tower 10B-6 1-1-1 Uchisaiwai-cho, Chiyoda-ku Tokyo 100-0011 Japan Tel: +81-3-3502-5211 Fax: +81-3-3502-5213 Americas: Tel: 858-731-9453 Europe, Asia Pacific: 180 Rue Jean de Guiramand 13852 Aix-En-Provence Cedex 3, France Tel: +33-4-4239-3361 Fax: +33-4-4239-7227 For a list of representatives in your area, please refer to our Web site at: www.psemi.com Data Sheet Identification Advance Information The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. Preliminary Specification The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a DCN (Document Change Notice). Document No. 70-0056-04 www.psemi.com The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user's own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine's products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS, HaRP and MultiSwitch are trademarks of Peregrine Semiconductor Corp. (c)2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 11 of 11