Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
LP295x Adjustable Micropower Low-Dropout Voltage Regulators
1 Features 3 Description
The LP2952 and LP2953 are micropower voltage
1 2.3-V to 30-V Input Voltage Range regulators with very low quiescent current (130 μA
Output Voltage Adjusts from 1.23 V to 29 V typical at 1-mA load) and very low dropout voltage
250-mA Output Current (typically 60 mV at light load and 470 mV at 250-mA
load current). They are ideally suited for battery-
Extremely Low Quiescent Current powered systems. Furthermore, the quiescent current
Low Dropout Voltage increases only slightly at dropout, which prolongs
Extremely Tight Line and Load Regulation battery life.
Very Low Temperature Coefficient The LP2952 and LP2953 retain all the desirable
Current and Thermal Limiting characteristics of the LP2951, but offer increased
output current, additional features, and an improved
Reverse Battery-Input Protection shutdown function.
50-mA (Typical) Automatic Output Discharge The automatic output discharge pulls the output down
LP2953 Versions Only quickly when the shutdown is activated.
Auxiliary Comparator Included With CMOS-
and TTL-Compatible Output Levels. Can Be The error flag goes low if the output voltage drops out
of regulation.
Used for Fault Detection, Low-Input Line
Detection, and so on. Reverse battery-input protection is provided.
The internal voltage reference is made available for
2 Applications external use, providing a low temperature coefficient
High-Efficiency Linear Regulator (20 ppm/°C) reference with very good line (0.03%)
and load (0.04%) regulation.
Regulator With Undervoltage Shutdown
Low-Dropout Battery-Powered Regulator Device Information(1)
Snap-ON/Snap-OFF Regulator PART NUMBER PACKAGE BODY SIZE (NOM)
LP2952x SOIC (16) 9.90 mm × 3.91 mm
SOIC (16) 9.90 mm × 3.91 mm
LP2953x PDIP (16) 21.755 mm × 6.35 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Typical Application Schematic
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
Table of Contents
7.3 Feature Description................................................. 15
1 Features.................................................................. 17.4 Device Functional Mode ......................................... 16
2 Applications ........................................................... 18 Application and Implementation ........................ 17
3 Description............................................................. 18.1 Application Information............................................ 17
4 Revision History..................................................... 28.2 Typical Applications ................................................ 21
5 Pin Configuration and Functions......................... 39 Power Supply Recommendations...................... 30
6 Specifications......................................................... 410 Layout................................................................... 31
6.1 Absolute Maximum Ratings ...................................... 410.1 Layout Guidelines ................................................. 31
6.2 ESD Ratings.............................................................. 410.2 Layout Example .................................................... 31
6.3 Recommended Operating Conditions....................... 410.3 Power Dissipation: Heatsink Requirements
6.4 Thermal Information.................................................. 5(Industrial Temperature Range Devices)................. 32
6.5 Electrical Characteristics: 3.3-V Versions................. 511 Device and Documentation Support................. 34
6.6 Electrical Characteristics: 5-V Versions.................... 511.1 Related Links ........................................................ 34
6.7 Electrical Characteristics: All Voltage Options.......... 611.2 Trademarks........................................................... 34
6.8 Typical Characteristics.............................................. 911.3 Electrostatic Discharge Caution............................ 34
7 Detailed Description............................................ 14 11.4 Glossary................................................................ 34
7.1 Overview................................................................. 14 12 Mechanical, Packaging, and Orderable
7.2 Functional Block Diagrams ..................................... 14 Information ........................................................... 34
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (December 2014) to Revision F Page
Deleted "Assured" .................................................................................................................................................................. 1
Changed "Output Pulldown Crowbar" to "Automatic Output Discharge" ............................................................................... 1
Changed "internal crowbar" to "automatic output discharge"................................................................................................. 1
Added word "input" after "battery" in Features and Description............................................................................................. 1
Changed pin names for IN and OUT to match TI nomenclature; fix typos............................................................................ 1
Changed max junc. temp from 125°C to 150°C .................................................................................................................... 4
Changed wording of footnote 12 ........................................................................................................................................... 8
Added second bullet for "LP2953 versions only" ................................................................................................................. 14
Added Automatic Output Dischange subsection ................................................................................................................. 16
Deleted sentence "To achieve the smallest form factor, the TO-92 package is selected.".................................................. 22
Changed "With an efficiency of 83.3% and a 250-mA maximum load, the internal power dissipation is 250 mW,
which corresponds to a 19.2°C junction temperature rise for the SOIC package." to "With a VIN VOUT differential of
1 V and a maximum load current of 250 mA the internal junction temperature (TJ) of the SOIC package will rise
19.2° above the ambient temperature."................................................................................................................................ 22
Deleted "Thermal Resistance for Various Copper Heatsinking Patterns" table................................................................... 33
Changes from Revision D (September 2013) to Revision E Page
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes,Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section; updated
Thermal Information values; deleted obsolete LP2953AM references .................................................................................. 1
Changes from Revision C (March 2005) to Revision D Page
Changed layout of National Data Sheet to TI format ........................................................................................................... 30
2Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
5 Pin Configuration and Functions
16 Pins 16 Pins
LP2952 SOIC (D) Package LP2953 SOIC (D) Package
Top View Top View
16 Pins
LP2953 PDIP (NBG) Package
Top View
Pin Functions LP2952-N
PIN I/O DESCRIPTION
NAME SOIC(D)
ERROR 6 O Error signal output
FEEDBACK 14 I Error amplifier noninverting input
GROUND 1, 8, 9, 16 - Ground
IN 15 I Regulator power input
NC 2, 7, 10, 11 - NC
OUT 3 O Regulated output voltage
REFERENCE 12 O Internal reference voltage output
SENSE 4 I Feedback voltage sense input
SHUTDOWN 5 I Shutdown input
VTAP 13 I Internal resistor divider input
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
Pin Functions LP2953
PIN I/O DESCRIPTION
NAME SOIC(D) PDIP(NBG)
COMPIN 10 15 I Auxiliary comparator input
COMPOUT 11 14 O Auxiliary comparator output
ERROR 6 10 O Error signal output
FEEDBACK 14 2 I Error amplifier noninverting input
GROUND 1, 8, 9, 16 4, 5, 12, 13 - Ground
IN 15 3 I Regulator power input
NC 2, 7 7, 11 - NC
OUT 3 6 O Regulated output voltage
REFERENCE 12 16 O Internal reference voltage output
SENSE 4 8 I Feedback voltage sense input
SHUTDOWN 5 9 I Shutdown input
VTAP 13 1 I Internal resistor divider input
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
Power dissipation(2) Internally Limited
Input supply voltage 20 30 V
FEEDBACK input voltage(3) 0.3 5 V
Comparator input voltage(4) 0.3 30 V
SHUTDOWN input voltage(4) 0.3 30 V
Comparator output voltage(4) 0.3 30 V
Maximum junction temperature 150 °C
Storage temperature, Tstg 65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal
resistance, RθJA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated
using the equation for P(MAX): P(MAX) = (TJ(MAX) TA) / RθJA.
Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal
shutdown. See Power Supply Recommendations for additional information on heatsinking and thermal resistance.
(3) When used in dual-supply systems where the regulator load is returned to a negative supply, the output voltage must be diode-clamped
to ground.
(4) May exceed the input supply voltage.
6.2 ESD Ratings VALUE UNIT
Electrostatic Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins(1) ±2000
V(ESD) V
discharge
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT
Operating junction temperature 40 125 °C
Input supply voltage 2.3 30 V
4Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
6.4 Thermal Information LP2952, LP2953 LP2953
THERMAL METRIC(1) SOIC (D) PDIP (NBG) UNIT
16 PINS
RθJA Junction-to-ambient thermal resistance 76.9 42.1
RθJC(top) Junction-to-case (top) thermal resistance 37.4 28.1
RθJB Junction-to-board thermal resistance 34.6 22.2 °C/W
ψJT Junction-to-top characterization parameter 7.3 12.0
ψJB Junction-to-board characterization parameter 34.3 22.1
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
6.5 Electrical Characteristics: 3.3-V Versions
Limits are assured by production testing or correlation techniques using standard Statistical Quality Control (SQC) methods.
Unless otherwise specified: MIN (minimum) and MAX (maximum) specifications in apply over the full Operating Temperature
Range and TYP (typical) values apply at TJ= 25°C, VIN = VOUT(NOM) + 1 V, IOUT = 1 mA, COUT = 2.2 μF for 5-V parts and 4.7
μF for 3.3-V parts. FEEDBACK pin is tied to VTAP pin, OUT pin is tied to SENSE pin.
LP2952AI-3.3, LP2953AI-3.3 LP2952I-3.3, LP2953I-3.3
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX
TJ= 25°C 3.284 3.3 3.317 3.267 3.3 3.333
VOUT Output voltage 3.260 3.3 3.340 3.234 3.3 3.366 V
1 mA IOUT 250 mA 3.254 3.3 3.346 3.221 3.3 3.379
6.6 Electrical Characteristics: 5-V Versions
Limits are assured by production testing or correlation techniques using standard Statistical Quality Control (SQC) methods.
Unless otherwise specified, MIN (minimum) and MAX (maximum) specifications in apply over the full Operating Temperature
Range and TYP (typical) values apply at TJ= 25°C, VIN = VOUT(NOM) + 1 V, IOUT = 1 mA, COUT = 2.2 μF for 5-V parts and 4.7
μF for 3.3-V parts. FEEDBACK pin is tied to VTAP pin, OUT pin is tied to SENSE pin.
LP2952AI, LP2953AI LP2952I, LP2953I
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX
TJ= 25°C 4.975 5 5.025 4.95 5 5.05
VOUT Output voltage 4.94 5 5.06 4.9 5 5.1 V
1 mA IOUT 250 mA 4.93 5 5.07 4.88 5 5.12
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
ûVOUT
ûPD
ûVOUT
ûV
ûVOUT
ûV
ûVOUT
ûT
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
6.7 Electrical Characteristics: All Voltage Options
Limits are assured by production testing or correlation techniques using standard Statistical Quality Control (SQC) methods.
Unless otherwise specified, MIN (minimum) and MAX (maximum) specifications in apply over the full Operating Temperature
Range and TYP (typical) values apply at TJ= 25°C, VIN = VOUT(NOM) + 1 V, IOUT = 1 mA, COUT = 2.2 μF for 5-V parts and 4.7
μF for 3.3-V parts. FEEDBACK pin is tied to VTAP pin, OUT pin is tied to SENSE pin.
LP2952AI, LP2953AI, LP2952I, LP2953I,
LP2952AI-3.3, LP2953AI-3.3(1) LP2952I-3.3, LP2953I-3.3
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX
REGULATOR
Output voltage
temperature See(2) 20 100 20 150 ppm/°C
coefficient TJ= 25°C 0.03% 0.1% 0.03% 0.2%
Output voltage VIN = VOUT(NOM) + 1 V to 30 V
line regulation VIN = VOUT(NOM) + 1 V to 30 V 0.03% 0.2% 0.03% 0.4%
TJ= 25°C 0.04% 0.16% 0.04% 0.20%
Output voltage IOUT = 1 mA to 250 mA
load regulation(3) IOUT = 0.1 mA to 1 mA 0.04% 0.20% 0.04% 0.30%
TJ= 25°C, IOUT = 1 mA 60 100 60 100
IOUT = 1 mA 60 150 60 150
IOUT = 50 mA 240 300 240 300
IOUT = 50 mA 240 420 240 420
Dropout
VIN VOUT mV
voltage(4) TJ= 25°C, IOUT = 100 mA 310 400 310 400
IOUT = 100 mA 310 520 310 520
TJ= 25°C, IOUT = 250 mA 470 600 470 600
IOUT = 250 mA 470 800 470 800
TJ= 25°C, IOUT = 1 mA 130 170 130 170 μA
IOUT = 1 mA 130 200 130 200
TJ= 25°C, IOUT = 50 mA 1.1 2 1.1 2
IOUT = 50 mA 1.1 2.5 1.1 2.5
Ground pin
IGND current(5) TJ= 25°C, IOUT = 100 mA 4.5 6 4.5 6 mA
IOUT = 100 mA 4.5 8 4.5 8
TJ= 25°C, IOUT = 250 mA 21 28 21 28
IOUT = 250 mA 21 33 21 33
VIN = VOUT(NOM) 0.5 V 165 210 165 210
Ground pin
IGND current at μA
IOUT = 100 μA165 240 165 240
dropout –40°C TJ125°C
Ground pin
IGND current at TJ= 25°C, VSHUTDOWN 1.1 V 105 140 105 140 μA
shutdown(5)
TJ= 25°C, VOUT = 0 380 500 380 500
ILIMIT Current limit mA
VOUT = 0 380 530 380 530
Thermal TJ= 25°C; see(6) 0.05 0.2 0.05 0.2 %/W
regulation
(1) Drive SHUTDOWN pin with TTL or CMOS low level to shut off regulator, high level to turn on regulator.
(2) Output or reference voltage temperature coefficient is defined as the worst-case voltage change divided by the total temperature range.
(3) Load regulation is measured at constant junction temperature using low duty-cycle pulse testing. Two separate tests are performed, one
for the range of IOUT = 100 μA to 1 mA and one for the range of IOUT =1 mA to 250 mA. Changes in output voltage due to heating
effects are covered by the thermal regulation specification.
(4) Dropout voltage is defined as the input-to-output differential at which the output voltage drops 100 mV below the value measured with a
1-V differential. At very low values of programmed output voltage, the input voltage minimum of 2 V (2.3 V over temperature) must be
observed.
(5) Ground pin current is the regulator quiescent current. The total current drawn from the source is the sum of the ground pin current,
output load current, and current through the external resistive divider (if used).
(6) Thermal regulation is the change in output voltage at a time t after a change in power dissipation, excluding load or line regulation
effects. Specifications are for a 200-mA load pulse at VIN = VOUT(NOM) + 15 V (3-W pulse) for t = 10 ms.
6Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
Electrical Characteristics: All Voltage Options (continued)
Limits are assured by production testing or correlation techniques using standard Statistical Quality Control (SQC) methods.
Unless otherwise specified, MIN (minimum) and MAX (maximum) specifications in apply over the full Operating Temperature
Range and TYP (typical) values apply at TJ= 25°C, VIN = VOUT(NOM) + 1 V, IOUT = 1 mA, COUT = 2.2 μF for 5-V parts and 4.7
μF for 3.3-V parts. FEEDBACK pin is tied to VTAP pin, OUT pin is tied to SENSE pin.
LP2952AI, LP2953AI, LP2952I, LP2953I,
LP2952AI-3.3, LP2953AI-3.3(1) LP2952I-3.3, LP2953I-3.3
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX
Output noise COUT = 4.7 μF 400 400
voltage (10 Hz μV
COUT = 33 μF 260 260
ento 100 kHz) RMS
COUT = 33 μF(7) 80 80
IOUT = 100 mA TJ= 25°C, see(8) 1.215 1.23 1.245 1.205 1.23 1.255
Reference
VREF V
voltage see(8), 1.205 1.255 1.19 1.27
Reference VIN = 2.5 V to VOUT + 1 V 0.03% 0.1% 0.03% 0.2%
voltage line VIN = VOUT(NOM)+ 1 V to 30 V(9) 0.03% 0.2% 0.03% 0.4%
regulation
Reference TJ= 25°C, IREF = 0 to 200 μA 0.25% 0.4% 0.25% 0.8%
voltage load IREF = 0 to 200 μA 0.25% 0.6% 0.25% 1.0%
regulation
Reference
voltage See(2), –40°C TJ125°C 20 20 ppm/°C
temperature
coefficient TJ= 25°C 20 40 20 40
Feedback pin
IB(FB) nA
bias current 20 60 20 60
TJ= 25°C; see (10) 30 30
Output off
IO(SINK) mA
pulldown current See (10) 20 20
DROPOUT DETECTION COMPARATOR
TJ= 25°C, VOH = 30 V 0.01 1 0.01 1
Output high
IOH μA
leakage VOH = 30 V 0.01 2 0.01 2
TJ= 25°C, VIN = VOUT(NOM)
0.5 V 150 250 150 250
Output low IOUT(COMP) = 400 μA
VOL mV
voltage VIN = VOUT(NOM) 0.5 V 150 400 150 400
IOUT(COMP) = 400 μA
TJ= 25°C, see(11) 80 60 35 80 60 35
Upper threshold
VTHR(MAX) mV
voltage See(11) 95 60 25 95 60 25
TJ= 25°C, see(11) 110 85 55 110 85 55
Lower threshold
VTHR(MIN) mV
voltage See(11) 160 85 40 160 85 40
HYST Hysteresis See(11) 15 15 mV
(7) Connect a 0.1-μF capacitor from the OUT pin to the FEEDBACK pin.
(8) VREF VOUT (VIN 1 V), 2.3 V VIN 30 V, 100 μAIOUT 250 mA.
(9) Two separate tests are performed, one covering 2.5 V VIN VOUT(NOM)) + 1 V and the other test for VOUT(NOM) + 1 V VIN 30 V.
(10) VSHUTDOWN 1.1 V, VOUT = VOUT(NOM)
(11) Comparator thresholds are expressed in terms of a voltage differential at the FEEDBACK pin below the nominal reference voltage
measured at VIN = VOUT(NOM) + 1 V. To express these thresholds in terms of output voltage change, multiply by the error amplifier gain,
which is VOUT / VREF = (R1 + R2) / R2 (see Figure 31).
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
Electrical Characteristics: All Voltage Options (continued)
Limits are assured by production testing or correlation techniques using standard Statistical Quality Control (SQC) methods.
Unless otherwise specified, MIN (minimum) and MAX (maximum) specifications in apply over the full Operating Temperature
Range and TYP (typical) values apply at TJ= 25°C, VIN = VOUT(NOM) + 1 V, IOUT = 1 mA, COUT = 2.2 μF for 5-V parts and 4.7
μF for 3.3-V parts. FEEDBACK pin is tied to VTAP pin, OUT pin is tied to SENSE pin.
LP2952AI, LP2953AI, LP2952I, LP2953I,
LP2952AI-3.3, LP2953AI-3.3(1) LP2952I-3.3, LP2953I-3.3
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX
SHUTDOWN INPUT(12)
TJ= 25°C 7.5 ±3 7.5 7.5 ±3 7.5
Input offset (Referred to VREF)
VOS mV
voltage 10 10 10 10
HYST Hysteresis 6 6 mV
TJ= 25°C 30 10 30 30 10 30
Input bias VIN(SD) = 0 V to 5 V
IBnA
current VIN(SD) = 0 V to 5 V 50 50 50 50
AUXILIARY COMPARATOR (LP2953 Only)
TJ= 25°C 7.5 ±3 7.5 7.5 ±3 7.5
Input offset (Referred to VREF)
VOS mV
voltage (Referred to VREF)10 ±3 10 10 ±3 10
HYST Hysteresis 6 6 mV
TJ= 25°C, VIN(COMP) = 0 V to 5 30 10 30 30 10 30
Input bias V
IBnA
current VIN(COMP) = 0 V to 5 V 50 10 50 50 10 50
TJ= 25°C, VOH = 30 V 0.01 1 0.01 1
Output high
IOH μA
leakage VIN(COMP) = 1.3 V 0.01 2 0.01 2
TJ= 25°C, VIN(COMP) = 1.1 V 150 250 150 250
Output low
VOL mV
voltage IOUT(COMP) = 400 μA 150 400 150 400
(12) Drive SHUTDOWN pin with TTL or CMOS-low level to shut regulator OFF, high level to turn regulator ON.
8Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
6.8 Typical Characteristics
Unless otherwise specified: VIN = 6 V, IOUT = 1 mA, COUT = 2.2 μF, VSD = 3 V, TA= 25°C, VOUT = 5 V.
Figure 1. Quiescent Current Figure 2. Quiescent Current
Figure 4. Ground Pin Current
Figure 3. Ground Pin Current vs Load
Figure 5. Ground Pin Current Figure 6. Output Noise Voltage
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified: VIN = 6 V, IOUT = 1 mA, COUT = 2.2 μF, VSD = 3 V, TA= 25°C, VOUT = 5 V.
Figure 7. Ripple Rejection Figure 8. Ripple Rejection
Figure 10. Line Transient Response
Figure 9. Ripple Rejection
Figure 11. Line Transient Response Figure 12. Output Impedance
10 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
Typical Characteristics (continued)
Unless otherwise specified: VIN = 6 V, IOUT = 1 mA, COUT = 2.2 μF, VSD = 3 V, TA= 25°C, VOUT = 5 V.
Figure 13. Load Transient Response Figure 14. Load Transient Response
Figure 16. Enable Transient
Figure 15. Dropout Characteristics
Figure 17. Enable Transient Figure 18. Short-Circuit Output Current and Maximum
Output Current
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified: VIN = 6 V, IOUT = 1 mA, COUT = 2.2 μF, VSD = 3 V, TA= 25°C, VOUT = 5 V.
Figure 19. Feedback Bias Current Figure 20. FEEDBACK Pin Current
Figure 22. Comparator Sink Current
Figure 21. Error Output
Figure 23. Divider Resistance Figure 24. Dropout Detection Comparator Threshold
Voltages
12 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
Typical Characteristics (continued)
Unless otherwise specified: VIN = 6 V, IOUT = 1 mA, COUT = 2.2 μF, VSD = 3 V, TA= 25°C, VOUT = 5 V.
Figure 25. Thermal Regulation Figure 26. Minimum Operating Voltage
Figure 27. Dropout Voltage
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
7 Detailed Description
7.1 Overview
The LP2952 and LP2953 are very high accuracy micropower voltage regulators with low quiescent current (130
μA, typical) and low dropout voltage (typically 60 mV at light loads and 490 mV at 250 mA). They are ideally
suited for use in battery-powered systems.
The LP2952 and LP2953 block diagram contains several features, including:
Very high accuracy 1.23-V reference.
Internal protection circuitry, such as thermal foldback current limit, thermal shutdown protection, and reverse
battery-input protection.
Fixed 5-V and 3.3-V versions.
Error flag output which may be used for a power-on reset.
Shutdown input, allowing turn off the regulator when the SHUTDOWN pin is pulled low.
LP2953 versions only:
An auxiliary comparator is designed for customer special purpose when shutdown is activated, this is a
CMOS- or TTL-compatible output level.
Automatic output discharge when the SHUTDOWN pin is pulled low.
7.2 Functional Block Diagrams
Figure 28. LP2952 Block Diagram
14 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
Functional Block Diagrams (continued)
Figure 29. LP2953 Block Diagram
7.3 Feature Description
7.3.1 Fixed Voltage Options and Programmable Voltage Version
The LP2952 and LP2953 provide 2 fixed output options: 3.3 V and 5 V. To meet different requirements for the
application, they can also be used as programmable voltage regulators with external resistor networks; see
Application Information for more details.
7.3.2 High-Accuracy Output Voltage
With special and careful design to minimize all contributions to the output voltage error, the LP2952 and LP2953
distinguished themselves as very high output voltage accuracy micropower LDO. This includes a tight initial
tolerance (0.5% typical), extremely good load and line regulation, and a very low output voltage temperature
coefficient, making the part an ideal a low-power voltage reference.
7.3.3 Error Detection Comparator Output
The LP2952 and LP2953 will generate a logic low output when the output falls out of regulation by more than
approximately 5%. See Application Information for more details.
7.3.4 Auxiliary Comparator
An auxiliary comparator is designed for customer special purpose when shutdown is activated. This block is still
active and can be used to generate fault detection, low input line detection signal for system controllers. The
comparator output level is CMOS- or TTL-compatible. See Application Information for more details.
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
Feature Description (continued)
7.3.5 Short-Circuit Protection (Current Limit)
The internal current limit circuit is used to protect the LDO against high-load current faults or shorting events. The
LDO is not designed to operate in a steady-state current limit. During a current-limit event, the LDO sources
constant current. Therefore, the output voltage falls when load impedance decreases. Note also that if a current
limit occurs and the resulting output voltage is low, excessive power may be dissipated across the LDO resulting
in a thermal shutdown of the output. A thermal foldback feature limits the short-circuit current to protect the
regulator from damage under all load conditions. If the OUT pin is forced below 0 V before SHUTDOWN goes
high and the load current required exceeds the thermal foldback current limit, the device may not start up
correctly.
7.3.6 Thermal Protection
The device contains a thermal shutdown protection circuit to turn off the output current when excessive heat is
dissipated in the LDO. The thermal time-constant of the semiconductor die is fairly short, and thus the output
cycles on and off at a high rate when thermal shutdown is reached until the power dissipation is reduced. The
internal protection circuitry of the device is designed to protect against thermal overload conditions. The circuitry
is not intended to replace a proper heatsink. Continuously running the device into thermal shutdown degrades its
reliability.
7.3.7 Automatic Output Discharge
Both LP2952 and LP2953 employ an internal 50-mA (typical) pulldown to discharge the output when the
SHUTDOWN pin is low and the output is disabled.
7.4 Device Functional Mode
7.4.1 Shutdown Mode
When pulling the SHUTDOWN pin to low level, the LP2952 and LP2953 will enter shutdown mode, and a very
low quiescent current is consumed. This function is designed for applications which needs a shutdown mode to
effectively enhance battery life cycle. When the SHUTDOWN pin is low the automatic output discharge circuity
will be active. See Application Information for more details.
7.4.2 Operation with 30 V VIN > VOUT(TARGET) +1V
The device operate if the input voltage is equal to, or exceeds, VOUT(TARGET) + 1 V, and SHUTDOWN is pulled to
high level. At input voltages below the minimum VIN requirement, the devices do not operate correctly and output
voltage may not reach target value.
16 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
Figure 30. Schematic Diagram
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
Application Information (continued)
8.1.1 External Capacitors
A 2.2-μF (or greater) capacitor is required between the OUT pin and ground to assure stability when the output is
set to 5 V. Without this capacitor, the device will oscillate. Most types of tantalum or aluminum electrolytic
capacitors will work here. Film types will work, but are more expensive. Many aluminum electrolytic capacitors
contain electrolytes which freeze at 30°C, which requires the use of solid tantalum capacitors below 25°C. The
important parameters of the capacitor are an equivalent series resistance (ESR) of about 5 Ωor less and a
resonant frequency above 500 kHz (the ESR may increase by a factor of 20 or 30 as the temperature is reduced
from 25°C to 30°C). The value of this capacitor may be increased without limit.
At lower values of output current, less output capacitance is required for stability. The capacitor can be reduced
to 0.68 μF for currents below 10 mA or 0.22 μF for currents below 1 mA.
Programming the output for voltages below 5 V runs the error amplifier at lower gains requiring more output
capacitance for stability. At 3.3-V output, a minimum of 4.7 μF is required. For the worst-case condition of 1.23-V
output and 250 mA of load current, a 6.8-μF (or larger) capacitor should be used.
A 1-μF capacitor should be placed from the IN pin to ground if there is more than 10 inches of wire between the
IN pin and the ac filter capacitor or if a battery input is used.
Stray capacitance to the FEEDBACK pin can cause instability. This problem is most likely to appear when using
high-value external resistors to set the output voltage. Adding a 100-pF capacitor between the OUT and
FEEDBACK pins and increasing the output capacitance to 6.8 μF (or greater) will cure the problem.
8.1.2 Minimum Load
When setting the output voltage using an external resistive divider, a minimum current of 1 μA is recommended
through the resistors to provide a minimum load.
It should be noted that a minimum load current is specified in several of the Electrical Characteristics: All Voltage
Options test conditions, so this value must be used to obtain correlation on these tested limits.
8.1.3 Programming the Output Voltage
The regulator may be pin-strapped for 5-V operation using its internal resistive divider by tying the OUTPUT and
SENSE pins together and also tying the FEEDBACK and VTAP pins together.
Alternatively, it may be programmed for any voltage between the 1.23-V reference and the 30-V maximum rating
using an external pair of resistors (see Figure 31). The complete equation for the output voltage is:
where
VREF is the 1.23-V reference and IFB is the FEEDBACK pin bias current (20 nA, typical). (1)
The minimum recommended load current of 1 μA sets an upper limit of 1.2 MΩon the value of R2 in cases
where the regulator must work with no load (see Minimum Load). IFB will produce a typical 2% error in VOUT
which can be eliminated at room temperature by trimming R1. For better accuracy, choosing R2 = 100 kΩwill
reduce this error to 0.17% while increasing the resistor program current to 12 μA. Because the typical quiescent
current is 120 μA, this added current is negligible.
18 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
Application Information (continued)
* See Power Supply Recommendations
** Drive with TTL-low to shutdown
Figure 31. Adjustable Regulator
8.1.4 Dropout Voltage
The dropout voltage of the regulator is defined as the minimum input-to-output voltage differential required for the
output voltage to stay within 100 mV of the output voltage measured with a 1-V differential. The dropout voltage
is independent of the programmed output voltage.
8.1.5 Dropout Detection Comparator
This comparator produces a logic low whenever the output falls out of regulation by more than about 5%. This
value results from the comparator built-in offset of 60 mV divided by the 1.23-V reference (see Functional Block
Diagrams). The 5% low trip level remains constant regardless of the programmed output voltage. An out-of-
regulation condition can result from low input voltage, current limiting, or thermal limiting.
Figure 32 gives a timing diagram showing the relationship between the output voltage, the ERROR output, and
input voltage as the input voltage is ramped up and down to a regulator programmed for 5-V output. The ERROR
signal becomes low at about 1.3-V input. It goes high at about 5-V input, where the output equals 4.75 V.
Because the dropout voltage is load dependent, the input voltage trip points will vary with load current. The
output voltage trip point does not vary.
The comparator has an open-collector output which requires an external pullup resistor. This resistor may be
connected to the regulator output or some other supply voltage. Using the regulator output prevents an invalid
high on the comparator output that occurs if it is pulled up to an external voltage while the regulator input voltage
is reduced below 1.3 V. In selecting a value for the pullup resistor, note that while the output can sink 400 μA,
this current adds to battery drain. Suggested values range from 100 kΩto 1 MΩ. This resistor is not required if
the output is unused.
When VIN 1.3 V, the ERROR pin becomes a high impedance, allowing the error flag voltage to rise to its pullup
voltage. Using VOUT as the pullup voltage (rather than an external 5-V source) will keep the error flag voltage
below 1.2 V (typical) in this condition. The user may wish to divide down the error flag voltage using equal-value
resistors (10 kΩis suggested) to ensure a low-level logic signal during any fault condition, while still allowing a
valid logic high level during normal operation.
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
Application Information (continued)
* In shutdown mode, ERROR will go high if it has been pulled up to an external supply. To avoid this invalid
response, pull up to regulator output.
** Exact value depends on dropout voltage. (See Power Supply Recommendations)
Figure 32. ERROR Output Timing
8.1.6 Output Isolation
The regulator output can be left connected to an active voltage source (such as a battery) with the regulator input
power shut off, as long as the regulator ground pin is connected to ground. If the ground pin is left floating,
damage to the regulator can occur if the output is pulled up by an external voltage source. If the regulator input
power (VIN) is applied, and the SHUTDOWN pin is low, the automatic output discharge circuit will be active, and
any voltage source applied to the output will be discharged to ground.
8.1.7 Reducing Output Noise
In reference applications it may be advantageous to reduce the ac noise present on the output. One method is to
reduce regulator bandwidth by increasing output capacitance. This is relatively inefficient, because large
increases in capacitance are required to get significant improvement.
Noise can be reduced more effectively by a bypass capacitor placed across R1 (see Figure 31). The formula for
selecting the capacitor to be used is:
(2)
This gives a value of about 0.1 μF. When this is used, the output capacitor must be 6.8 μF (or greater) to
maintain stability. The 0.1-μF capacitor reduces the high-frequency gain of the circuit to unity, lowering the output
noise from 260 μV to 80 μV using a 10-Hz to 100-kHz bandwidth. Also, noise is no longer proportional to the
output voltage, so improvements are more pronounced at high output voltages.
20 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
Application Information (continued)
8.1.8 Auxiliary Comparator (LP2953 Only)
The LP2953 contains an auxiliary comparator whose inverting input is connected to the 1.23-V reference. The
auxiliary comparator has an open-collector output whose electrical characteristics are similar to the dropout
detection comparator. The noninverting input and output are brought out for external connections.
8.1.9 SHUTDOWN Input
A logic-level signal will shut off the regulator output when a low (< 1.2 V) is applied to the SHUTDOWN input.
To prevent possible mis-operation, the SHUTDOWN input must be actively terminated. If the input is driven from
open-collector logic, a pullup resistor (20 kΩto 100 kΩis recommended) should be connected from the
SHUTDOWN input to the regulator input.
If the SHUTDOWN input is driven from a source that actively pulls high and low (like an op-amp), the pullup
resistor is not required, but may be used.
If the shutdown function is not to be used, the cost of the pullup resistor can be saved by simply tying the
SHUTDOWN input directly to the regulator input.
NOTE
Because the Absolute Maximum Ratings state that the SHUTDOWN input can not go
more than 0.3 V below ground, the reverse battery-input protection feature which protects
the regulator input is sacrificed if the SHUTDOWN input is tied directly to the regulator
input.
If reverse-battery input protection is required in an application, the pullup resistor between the SHUTDOWN input
and the regulator input must be used.
8.2 Typical Applications
8.2.1 Basic 5-V Regulator
Figure 33. Basic 5-V Regulator
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
Typical Applications (continued)
8.2.1.1 Design Requirements
For this design example, use the parameters listed in Table 1 as the input parameters.
Table 1. Design Parameters
DESIGN PARAMETER DESIGN REQUIREMENT
Input voltage 6 V, ±10%, provided by the DC-DC converter switching at 1 MHz
Output voltage 5 V, ±1%
Output current 250 mA (maximum), 1 mA (minimum)
RMS noise, 10 Hz to 100 kHz 1 mV typical
PSRR at 1 kHz 50 dB typical
8.2.1.2 Detailed Design Procedure
At 150-mA loading, the dropout of the LP2952 and LP2953 has 600-mV maximum dropout over temperature
thus, a 1500-mV headroom is sufficient for operation over both input and output voltage accuracy. The efficiency
of the LP2952 and LP2953 in this configuration is VOUT / VIN = 83.3%. Input and output capacitors are selected in
accordance with the External Capacitors section. Ceramic capacitances of 1 μF for the input and one 2.2-μF
capacitor for the output are selected. With an efficiency of 83.3% and a 250-mA maximum load, the internal
power dissipation is 250 mW, which corresponds to a 19.2°C junction temperature rise for the SOIC package.
With a VIN VOUT differential of 1 V and a maximum load current of 250 mA the internal junction temperature (TJ)
of the SOIC package will rise 19.2°C above the ambient temperature. With an 85°C maximum ambient
temperature, the junction temperature is at 104.2°C. To minimize noise, a bypass capacitor of 100 pF is selected
between OUT and FEEDBACK pins.
8.2.1.3 Application Curves
Figure 34. Line Transient Response Figure 35. Load Transient Response
22 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
8.2.2 5-V Current Limiter with Load Fault Indicator
Figure 36 is the example circuit for 5-V current limiter with load fault indicator, it has the following features:
Output voltage equals +VIN minimum dropout voltage, which varies with output current. Current limits at a
maximum of 380 mA (typical).
Select R1 so that the comparator input voltage is 1.23 V at the output voltage which corresponds to the
desired fault current value.
Figure 36. 5-V Current Limiter With Load Fault Indicator
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 23
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
8.2.3 Low Temperature Coefficient Current Sink
The LP2952 or LP2953 can be used as a low drift current source as Figure 37 shows. By connecting VOUT to
FEEDBACK, VOUT will be regulated at 1.235 V, and current consumption at R is IOUT = 1.23/R.
Figure 37. Low Temperature Coefficient Current Sink
24 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
8.2.4 5-V Regulator With Error Flags for Low Battery and Out of Regulation
Figure 38 is the example circuit for 5-V regulator with error flags for low battery and out of regulation, it has the
following features:
Connect to logic or microprocessor control inputs.
LOW BATT flag warns the user that the battery has discharged down to about 5.8 V, giving the user time to
recharge the battery or power down some hardware with high power requirements. The output is still in
regulation at this time.
OUT OF REGULATION flag indicates when the battery is almost completely discharged, and can be used to
initiate a power-down sequence.
Figure 38. 5-V Regulator With Error Flags for Low Battery and Out of Regulation
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 25
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
8.2.5 5-V Battery Powered Supply With Backup and Low Battery Flag
Figure 39 is the example circuit for 5-V battery powered supply with backup and low battery flag, it has the
following features:
The circuit switches to the NI-CAD backup battery when the main battery voltage drops below about 5.6 V
and returns to the main battery when its voltage is recharged to about 6 V.
The 5-V MAIN output powers circuitry which requires no backup, and the 5-V MEMORY output powers critical
circuitry which cannot be allowed to lose power.
The BATTERY LOW flag goes low whenever the circuit switches to the NI-CAD backup battery.
Figure 39. 5-V Battery Powered Supply With Backup and Low Battery Flag
26 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
8.2.6 5-V Regulator With Timed Power-On Reset
Figure 40 is the circuit designed to generate a adjustable power on reset signal. Adjusting RTand CTvalues
causes a certain delay time as Figure 41 shows.
Figure 40. 5-V Regulator With Timed Power-On Reset
* RT= 1 MΩ, CT= 0.1 μF
Figure 41. Timing Diagram for Timed Power-On Reset
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 27
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
8.2.7 5-V Regulator With Snap-ON and Snap-OFF Features and Hysteresis
Figure 42 is the circuit designed to generate 5-V regulator with snap-ON and snap-OFF features and hysteresis.
The output turns on at VIN = 5.87 V and turns off at VIN = 5.64 V.
* Turns on at VIN = 5.87 V
Turns off at VIN = 5.64 V
(for component values shown)
Figure 42. 5-V Regulator With Snap-ON and Snap-OFF Features and Hysteresis
28 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
8.2.8 5-V Regulator With Error Flags for Low Battery and Out of Regulation With Snap-ON or Snap-OFF
Output
Figure 43 is the circuit as 5-V regulator with error flags for low battery and out of regulation with Snap-ON/Snap-
OFF output. It has the following features:
Connect to logic or microprocessor control inputs.
LOW BATT flag warns the user that the battery has discharged down to about 5.8 V, giving the user time to
recharge the battery or shutdown hardware with high power requirements. The output is still in regulation at
this time.
OUT OF REGULATION flag goes low if the output goes below about 4.7 V, which could occur from a load
fault.
OUTPUT has Snap-ON or Snap-OFF feature. Regulator snaps ON at about 5.7-V input, and OFF at about
5.6 V.
Figure 43. 5-V Regulator With Error Flags for Low Battery and Out of Regulation With Snap-ON or Snap-
OFF Output
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 29
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
8.2.9 5-V Regulator With Timed Power-On Reset, Snap-ON and Snap-OFF Features, and Hysteresis
Figure 44 is the circuit designed for 5-V regulator with timed power-on reset, Snap-ON and Snap-OFF features,
and hysteresis. Its timing diagram shows as Figure 45.
Figure 44. 5-V Regulator With Timed Power-On Reset, Snap-ON or Snap-OFF Feature, and Hysteresis
td= (0.28), RC = 28 ms for components shown.
Figure 45. Timing Diagram
9 Power Supply Recommendations
The LP2952 and LP2953 is designed to operate from an input voltage supply range between 2.3 V and 30 V.
The input voltage range provides adequate headroom in order for the device to have a regulated output, normally
VIN should be 1 V higher than output voltage to provide a sufficient headroom. This input supply must be well
regulated. If the input supply is noisy, additional input capacitors with low ESR can help improve the output noise
performance.
Maximum VIN should never be higher than 30 V. Input voltage beyond 30 V may trigger EOS and cause
permanent damage to the device.
30 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
Ground
VOUT
VIN
Input
Capacitor
Output
Capacitor
GND
NC
OUT
SENSE VTAP
GROUND
FEEDBACK
IN
Error Pullup
Resistor
Vout
SHUTDOWN
ERROR
NC
GROUND GROUND
REFERENCE
NC
NC
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
10 Layout
10.1 Layout Guidelines
For best overall performance, place all circuit components on the same side of the circuit board and as near as
practical to the respective LDO pin connections. Place ground return connections to the input and output
capacitors, and to the LDO ground pin as close to each other as possible, connected by a wide, component-side,
copper surface. The use of vias and long traces to create LDO circuit connections is strongly discouraged and
negatively affects system performance. This grounding and layout scheme minimizes inductive parasitics, and
thereby reduces load-current transients, minimizes noise, and increases circuit stability.
A ground reference plane is also recommended and is either embedded in the PCB itself or located on the
bottom side of the PCB opposite the components. This reference plane serves to assure accuracy of the output
voltage, shield noise, and behaves similar to a thermal plane to spread (or sink) heat from the LDO device. In
most applications, this ground plane is necessary to meet thermal requirements.
10.2 Layout Example
Figure 46. Layout Schematic
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 31
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
10.3 Power Dissipation: Heatsink Requirements (Industrial Temperature Range Devices)
The maximum allowable power dissipation for the LP2952 or LP2953 is limited by the maximum operating
junction temperature (125°C) and the external factors that determine how quickly heat flows away from the part:
the ambient temperature and the junction-to-ambient thermal resistance (RθJA) for the specific application.
The industrial temperature range (40°C TJ125°C) parts are manufactured in PDIP and surface-mount
packages which contain a copper lead frame that allows heat to be effectively conducted away from the die,
through the ground pins of the IC, and into the copper of the PC board. Details on heatsinking using PC board
copper are covered later.
Figure 47. Power Dissipation vs Ambient Temperature
for RθJA = 95°C/W
To determine if a heatsink is required, the maximum power dissipated by the regulator, P(MAX), must be
calculated. It is important to remember that if the regulator is powered from a transformer connected to the AC
line, the maximum specified AC input voltage must be used (because this produces the maximum DC input
voltage to the regulator). Figure 48 shows the voltages and currents which are present in the circuit. The formula
for calculating the power dissipated in the regulator is also shown in Figure 48:
Figure 48. PTOTAL = (VIN VOUT) IOUT + (VIN) IG
Current/Voltage Diagram
The next parameter which must be calculated is the maximum allowable temperature rise, TR(MAX). This is
calculated by using the formula:
TR(MAX) = TJ(MAX) TA(MAX) = RθJA × P(MAX)
where:
TJ(MAX) is the maximum allowable junction temperature
TA(MAX) is the maximum ambient temperature (3)
Using the calculated values for TR(MAX) and P(MAX), the required value for junction-to-ambient thermal resistance,
RθJA, can now be found.
32 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
www.ti.com
SNVS095F MAY 2004REVISED MARCH 2015
Power Dissipation: Heatsink Requirements (Industrial Temperature Range Devices) (continued)
The heatsink is made using the PC board copper. The heat is conducted from the die, through the lead frame
(inside the part), and out the pins which are soldered to the PC board. The pins used for heat conduction are
given in Table 2.
Table 2. Heat Conducting Pins
PART PACKAGE PINS
LP2953IN, LP2953AIN 16-pin PDIP 4, 5, 12, 13
LP2953IN-3.3, LP2953AIN-3.3
LP2952IM, LP2952AIM
LP2952IM-3.3, LP2952AIM-3.3 16-pin surface mount (SOIC) 1, 8, 9, 16
LP2953IM, LP2953AIM
LP2953IM-3.3, LP2953AIM-3.3
Figure 49 shows copper patterns which may be used to dissipate heat from the LP2952 and LP2953.
* For best results, use L = 2H.
** 14-Pin PDIP is similar, see Table 2 for pins designated for heatsinking.
Figure 49. Copper Heatsink Patterns
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 33
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
LP2952-N
,
LP2952A
,
LP2953
,
LP2953A
SNVS095F MAY 2004REVISED MARCH 2015
www.ti.com
11 Device and Documentation Support
11.1 Related Links
Table 3 lists quick access links. Categories include technical documents, support and community resources,
tools and software, and quick access to sample or buy.
Table 3. Related Links
TECHNICAL TOOLS & SUPPORT &
PARTS PRODUCT FOLDER SAMPLE & BUY DOCUMENTS SOFTWARE COMMUNITY
LP2952-N Click here Click here Click here Click here Click here
LP2952A Click here Click here Click here Click here Click here
LP2953 Click here Click here Click here Click here Click here
LP2953A Click here Click here Click here Click here Click here
11.2 Trademarks
All trademarks are the property of their respective owners.
11.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.4 Glossary
SLYZ022 TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
34 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LP2952-N LP2952A LP2953 LP2953A
PACKAGE OPTION ADDENDUM
www.ti.com 11-Jan-2021
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead finish/
Ball material
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LP2952AIM NRND SOIC D 16 48 Non-RoHS
& Green Call TI Call TI -40 to 125 LP2952AIM
LP2952AIM/NOPB ACTIVE SOIC D 16 48 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 LP2952AIM
LP2952AIMX/NOPB ACTIVE SOIC D 16 2500 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 LP2952AIM
LP2952IM NRND SOIC D 16 48 Non-RoHS
& Green Call TI Call TI -40 to 125 LP2952IM
LP2952IM/NOPB ACTIVE SOIC D 16 48 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 LP2952IM
LP2952IMX/NOPB ACTIVE SOIC D 16 2500 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 LP2952IM
LP2953AIM/NOPB ACTIVE SOIC D 16 48 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 LP2953AIM
LP2953AIMX/NOPB ACTIVE SOIC D 16 2500 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 LP2953AIM
LP2953IM/NOPB ACTIVE SOIC D 16 48 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 LP2953IM
LP2953IMX/NOPB ACTIVE SOIC D 16 2500 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 LP2953IM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
PACKAGE OPTION ADDENDUM
www.ti.com 11-Jan-2021
Addendum-Page 2
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LP2952AIMX/NOPB SOIC D 16 2500 330.0 16.4 6.5 10.3 2.3 8.0 16.0 Q1
LP2952IMX/NOPB SOIC D 16 2500 330.0 16.4 6.5 10.3 2.3 8.0 16.0 Q1
LP2953AIMX/NOPB SOIC D 16 2500 330.0 16.4 6.5 10.3 2.3 8.0 16.0 Q1
LP2953IMX/NOPB SOIC D 16 2500 330.0 16.4 6.5 10.3 2.3 8.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 8-Oct-2016
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LP2952AIMX/NOPB SOIC D 16 2500 367.0 367.0 35.0
LP2952IMX/NOPB SOIC D 16 2500 367.0 367.0 35.0
LP2953AIMX/NOPB SOIC D 16 2500 367.0 367.0 35.0
LP2953IMX/NOPB SOIC D 16 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 8-Oct-2016
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party
intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages,
costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either
on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s
applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021, Texas Instruments Incorporated