KQ
high Q inductor
Unless otherwise specified, measurements shall be performed within 2 hours after leaving
test samples for more than one hour at the normal temperature and at the normal humidity.
environmental applications (continued)
Performance Characteristics
Parameter
Dropping 1m on the ground of concrete, 1 time
∆L/L within ±5%
∆Q/Q within ±10%
2 hours in each direction of X, Y, Z on PCB at a frequency range
of 10 - 55 - 10Hz with 1.5mm amplitude
Maximum ∆L Test Method
Dropping
Resistance to Solvents
Dielectric Withstanding Voltage
No evidence of flaming,
fuming or breakdown
5 seconds @ AC 500V applied between both terminals and film
Accordance with MIL-STD-202, Method 215
No evidence of damage
∆L/L within ±5%
∆Q/Q within ±10%
40°C ± 2°C, 90 - 95% RH, 1000 hours
KQT0402: 60°C ± 2°C, 90 - 95% RH, 1000 hours
Moisture Endurance
No evidence of damage
∆L/L within ±5%
∆Q/Q within ±10%
Biased to full rated current @ +125°C, 1000 hours
Load Life
No evidence of damage
∆L/L within ±5%
∆Q/Q within ±10%
100 cycles between -40°C/hour and +125°C/hour
Thermal Shock
No evidence of damage
∆L/L within ±5%
∆Q/Q within ±10%
Biased to 10% rated current @ +85°C, 85% RH, 1000 hours
High Temperature
High Humidity
No evidence of damage
∆L/L within ±5%
∆Q/Q within ±10%
Vibration
95% of the terminal should be
covered with new solder
Immerse in solder @ 230° ± 5°C for 3 seconds ± 0.5 secondSolderability
No damage and marking
must remain legible
Terminal Pull Strength Terminals shall withstand a pull of 10N in a horizontal direction
(KQ0402 and KQ0603 = 5N, KQ0805 and KQ1008 = 10N)
No evidence of damage
Terminal Bending Strength Specimen shall be soldered on bend test board and force applied to the
opposite side to cause a 10mm deflection (KQ0603 = 3mm deflection)
No evidence of breakdown
∆L/L within ±5%
1 minute @ DC 100V measured between both terminals and film
1000MΩand over
Insulation Resistance
Withstands needle-flame test
IEC 695-2-2
Flammability
Immerse in solder @ 260° ± 5°C for 10 seconds ± 1 second
No evidence of outer damage
∆L/L within ±5%
∆Q/Q within ±10%
Resistance to Solder Heat
Store @ -40°C ±2°C for 1000 hours
No evidence of damage
∆L/L within ±5%
∆Q/Q within ±10%
Low Temperature Storage
Store @ +125°C ±2°C for 1000 hours
No evidence of damage
∆L/L within ±5%
∆Q/Q within ±10%
High Temperature Storage
Temperature Characteristics ∆L/L to be measured at the temperatures between -40°C and +125°C,
reference to the inductance @ 20°C
179
KOA Speer Electronics, Inc. • Bolivar Drive • P.O. Box 547 • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 11/01/03
inductors