Installation Notes LPS110 Series 110 Watts Single Output Input Specifications Output Specifications Input range 85 VAC to 264 VAC 120 to 370 VDC Maximum total wattage 80 W for convection; 110 W with 30 CFM forced air Frequency 47 - 440 Hz Adjustment range 5% minimum Inrush current < 18 A peak @ 115 VAC < 36 A peak @ 230 VAC Hold-up time 20 ms at full load and 115 VAC nominal line Overload protection Short circuit protection on all outputs. Auto recovery. Total power limited @ 110% to 135% above peak rating Overvoltage protection 5V output: 5.7 to 6.7 Vdc. Other outputs 10 to 25% above nominal output; recycle AC to reset Input current 2.5 A max. (RMS) @ 115 VAC Efficiency 70% typical at full load EMI filter Meets FCC Class B CISPR 22 Class B (includes EN55022 class B and VDE 0878 PT3 class B) Electromagnetic Meets IEC801-2 level 3, compatibility IEC801-4 level 3 and IEC801-5 level 3 Safety ground < 0.5mA @ 50/60Hz, leakage current 264Vac input Environmental Operating temperature: 0C to 50C ambient; derate at 2.5% / C from 50C to 70C Storage temperature:-40C to 85C Thermal regulation: 0.04% / C MTBF: > 100,000 hours at full load and 25C ambient conditions Safety VDE UL CSA NEMKO BABT CB 0805/EN60950 (IEC950) UL1950 CSA 22-2-234 Level 3 EN 60950/EMKO-TUE (74-sec) 203 EN60950/BS7002 Certificate and report This product is CE marked following the provisions of the Low Voltage Directive 73/23/EEC Notes (refer to table) 1. Peak current lasting < 30 seconds with a maximum 10% duty cycle. 2. At 25C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 F in parallel with a 0.1 F capacitor. 4. Total power drawn must not exceed 80W with convection cooling or 110W fan cooled. Mating Connectors AC Input: Housing Molex 09-91-0500 (or 26-03-4050) DC Output: Housing Molex 09-91-0900 (or 26-03-4090) Contacts: 18/24 AWG Molex 08-50-0106 (or 08-58-0189) Sense / P OK: Housing Molex 22-01-2025 Contacts: 22/30 AWG Molex 08-50-0114 Notes 1 Specifications subject to change without notice. 2 All dimensions are in mm and (inches). 3 Mounting holes M1 and M2 should be earthed for EMI purposes. 4 Output Common capacitivily coupled to M2 earth. 5 Mounting hole M1 is safety earth connection. This power supply must be earthed for safe operation via mounting hole M1 or SK1-3 connector. 6 Weight 0.75 kg / 1.65 lb. Warning: Hazardous mains voltages present within this unit. Primary heatsink is live. Please see enclosed `Astec Installation and Operating Instructions'. Use of optional cover kit is recommended for safe operation. Power OK SK202 pin1 POK 1 2 pin2 common Power OK signal;-TTL compatible signal goes high 50-150ms after switch on. Goes low >1.5 ms before loss of regulation Remote Sense 1 SK201 pin1 +sense 2 pin2 -sense This power supply has a connector for output remote sense. This can be used to compensate for cable voltage drops of up to 0.5V. If this feature is not used the power supply reverts to internal local sense. Protected against reverse connection. Cover Cover available Overall dimensions with cover 193.5 (7.62) x 115.6 (4.55) x 63 (2.48). Total power with cover derates to:- 70W convection, 90W with 30CFM forced air. Fusing Input fuse 4A 20mm Quick Acting HBC mains fuse - only replace with same type and rating to maintain safety standards. Order Code Model Number Output Voltage LPS112-B LPS113-B LPS114-B LPS115-B LPS118-B 5V 12 V 15 V 24 V 48 V Minimum Load Maximum Load with 4 Convection Cooling 0A 0A 0A 0A 0A Maximum Load 4 w/ 30CFM Air 16A 6.7 A 5.3 A 3.3 A 1.7 A 22 A 9.2A 7.3 A 4.6 A 2.3 A Peak Regulation 1 Load 25A 10.4A 8.3A 5.2A 2.6A 2% 2% 2% 2% 2% 2 Ripple 3 P/P (PARD) 50 mV 120 mV 150 mV 240 mV 480 mV Drawings 6.35 (0.25) 4.0 (0.156") DIA (4 places) M2 22.6 (0.89) 1 2 3 4 5 6 7 8 9 SK202 SK201 101.6 (4.0) 88.9 (3.5) SK2 63.5 (2.5) 3 GND 2 N 1 108.6 (4.28) Voltage Adjust Pot. SK1 L 22.6 (0.89) M1 165.1 (6.5) 6.35 (0.25) Customer mountings #6-32 bush - 6 places max. penetration 5.0 (0.20) 162.6 (6.4) 11.4 (0.45) 177.8 (7.0) 185.5 (7.3) 56 (2.2) 46.0 (1.8) 21.8 (0.86) 150 (5.9) 2.0 (0.08) Connector LPS112-B LPS113-B LPS114-B LPS115-B LPS118-B SK1-1 SK1-2 SK1-3 Line Neutral GND Line Neutral GND Line Neutral GND Line Neutral GND Line Neutral GND SK2-1 SK2-2 SK2-3 SK2-4 SK2-5 SK2-6 SK2-7 SK2-8 SK2-9 +5 V +5 V +5 V Common Common Common Common +5 V +5 V +12 V +12 V +12 V Common Common Common Common +12 V +12 V +15 V +15 V +15 V Common Common Common Common +15 V +15 V +24 V +24 V +24 V Common Common Common Common +24 V +24 V +48V +48V +48V Common Common Common Common +48V +48V SK202 P OK Common SK201-1 SK201-2 SK202-1 SK202-2 1 2 SK201 2 -Sense 1 +Sense +sense -sense POK Common Astec Standard Power Europe Astec House, Waterfront Business Park, Merry Hill, Dudley, West Mids. DY5 1LX, UK. Tel: +44 (0) 1384 842211 Fax: +44 (0) 1384 843355 Astec France S.A.R.L. Les Arcades, 424, la Closerie Mont d'Est, 93194 Noisy Le Grand Cedex, France. Tel: +33 1 4305 8680 Fax:+33 1 4304 6033 Supplied by Astec Standard Power Germany Astec Standard Power Europe Robert-Heil-Str. 8, 36251 Bad Hersfeld, Germany Tel: +49 (0) 6621 50570 Fax: +49 (0) 6621 505720 Published by ASPE Ref. No. 00262 A Notice d'Installation Series LPS110 110 Watt Simple sortie Caracteristiques d'entree Caracteristiques de sortie Plage de tension 85 VAC a 264 VAC 120 a 370 VDC Puissance max 80W avec convection naturelle 110W avec ventilation 14l/s Frequence 47 - 440 Hz Plage d'ajustement 5% minimum Courant d'appel < 18 A pointe @ 115 VAC < 36 A pointe @ 230 VAC Temps de maintien 20ms a pleine charge et 115VAC d'entree Protection surcharge Protection court circuit sur toutes les sorties avec redemarrage automatique Puissance totale limitee de 110% a 135% des valeurs cretes Protection surtension Sortie 5V: 5,7V a 6,7VDC. Autres sorties 10 a 25% de la tension nominale. Debrancher l'entree pour redemarrage Courant d'entree 2.5 A max. (RMS) @ 115 VAC Rendement 70% typique a pleine charge Filtre EMI repond a FCC Classe B CISPR 22 Classe B (inclut EN55022 classe B et VDE 0878 PT3 clases B) Compatibilite repond a IEC801-2 niveau 3, electromagnetique IEC801-4 niveau 3 et IEC801-5 niveau 3 Courant de fuite < 0.5mA @ 50/60Hz, 264Vac entree Caracteristiques d'environnement Temperature de fonctionnement: 0C a 50C ambiante; Decroit a 2.5% / C de 50C a 70C Temperature de stockage: -40C a 85C Stabilite thermique: 0.04% / C MTBF >100.000 heures a pleine charge et 25C d'ambiante Securite VDE UL CSA NEMKO BABT CB Notes (consulter le tableau) 1. Courant de pointe < 30 secondes avec un rapport de cycle maximum de 10% 2. A 25C incluant les tolerances initiales, la tension d'entree, les courants de charge, et pour des tensions de sortie ajustees en usine. 3. Crete a crete avec une bande passante de 20Mhz et un condensateur de 10F en parallele avec un 0,1F 4. La puissance totale tiree ne doit pas exceder 80W en convection naturelle et 110W en convection forcee. Connecteurs Entree secteur:Boitier Sortie : Boitier Molex 09-91-0500 (or 26-03-4050) Molex 09-91-0900 (or 26-03-4090) Contacts: 18/24 AWG Molex 08-50-0106 (or 08-58-0189) Teleregulation: Boitier Molex 22-01-2025 Contacts: 22/30 AWG Molex 08-50-0114 Notes 1 Les specifications peuvent etre modifiees sans avis. 2 Toutes les dimensions sont en mm et en (pouce). 3 Les trous de fixation M1 et M2 doivent etre connectes a la terre pour des raisons d'EMI. 4 Le commun de sortie est decouple par rapport au point de terre M2. 5 Le trou de fixation M1 est la connexion de la terre. L'alimentation doit etre connectee a la terre par l'intermediaire de M1 ou SK1-3 et ceci pour des raisons de securite. 6 Poids: 0,75kg 0805/EN60950 (IEC950) UL1950 CSA 22-2-234 Level 3 EN60950/EMKO-TUE (74-sec) 203 EN60950/BS7002 Certificat et rapport Ce produit est marque CE suivant la directive basse tension 73/23/CEE Power OK SK202 broche 1 POK 1 '' 2 commun 2 Signal compatible TTL haut 50-150ms apres mise en route. bas 1,5ms avant la perte de regulation. Teleregulation SK201 broche 1 + sense 1 `' 2 - sense 2 Cette alimentation possede un connecteur pour la teleregulation. Elle peut etre utilisee pour compenser des chutes en ligne jusqu'a 0,5V. En cas de non utilisation l'alimentation fonctionne en locale. L'alimentation est protegee contre les inversions de polarite. Attention: Tension secteur dangereuse sur cette alimentation. Refroidisseur primaire non isole. Veuillez consulter la notice d'installation ASTEC et les instructions d'utilisation. L'utilisation du kit capot est recommandee pour l'utilisation en toute securite. Capot Kit capot disponible Dimensions hors tout du capot 193.5 (7.62) x 115.6 (4.55) x 63 (2.48). Puissance totale avec capot 70W en convection 90W avec ventilation 14l/s Fusible Fusible d'entree 4A 20mm rapide HBC a remplacer par le meme type et la meme valeur pour maintenir les homologations de securite. Order Code Modele Tension Charge Charge Maximum Charge Maximum Charge de Sortie Minimum en ConvectionNaturelle4 avecVentilation 14l/s4 LPS112-B LPS113-B LPS114-B LPS115-B LPS118-B 5V 12 V 15 V 24 V 48 V 0A 0A 0A 0A 0A 16A 6.7 A 5.3 A 3.3 A 1.7 A 22 A 9.2A 7.3 A 4.6 A 2.3 A 25A 10.4A 8.3A 5.2A 2.6A Regulation 2 Residuelle3 en Pointe1 2% 2% 2% 2% 2% 50 mV 120 mV 150 mV 240 mV 480 mV Plan Mecanique 6.35 (0.25) 4.0 (0.156") DIA (4 places) M2 22.6 (0.89) 1 2 3 4 5 6 7 8 9 SK202 SK201 101.6 (4.0) 88.9 (3.5) SK2 63.5 (2.5) 3 GND 2 N 1 108.6 (4.28) Voltage Adjust Pot. SK1 L 22.6 (0.89) M1 165.1 (6.5) 6.35 (0.25) Customer mountings #6-32 bush - 6 places max. penetration 5.0 (0.20) 162.6 (6.4) 11.4 (0.45) 177.8 (7.0) 185.5 (7.3) 56 (2.2) 46.0 (1.8) 21.8 (0.86) 150 (5.9) 2.0 (0.08) Raccordement Connecteur LPS112-B LPS113-B LPS114-B LPS115-B LPS118-B SK1-1 SK1-2 SK1-3 Phase Neutre GND Phase Neutre GND Phase Neutre GND Phase Neutre GND Phase Neutre GND SK2-1 SK2-2 SK2-3 SK2-4 SK2-5 SK2-6 SK2-7 SK2-8 SK2-9 +5 V +5 V +5 V Commun Common Commun Commun +5 V +5 V +12 V +12 V +12 V Commun Commun Commun Commun +12 V +12 V +15 V +15 V +15 V Commun Commun Commun Commun +15 V +15 V +24 V +24 V +24 V Commun Commun Commun Commun +24 V +24 V +48V +48V +48V Commun Commun Commun Commun +48V +48V SK202 P OK Common SK201-1 SK201-2 SK202-1 SK202-2 1 2 SK201 2 -Sense 1 +Sense +sense -sense POK Commun Astec Standard Power Europe Astec House, Waterfront Business Park, Merry Hill, Dudley, West Mids. DY5 1LX, UK. Tel: +44 (0) 1384 842211 Fax: +44 (0) 1384 843355 Astec France S.A.R.L. Les Arcades, 424, la Closerie Mont d'Est, 93194 Noisy Le Grand Cedex, France. Tel: +33 1 4305 8680 Fax:+33 1 4304 6033 Astec Standard Power Germany Robert-Heil-Str. 8, 36251 Bad Hersfeld, Germany Tel: +49 (0) 6621 50570 Fax: +49 (0) 6621 505720 Published by ASPE Ref. No. 00262 A Bedienungs Anleitung LPS110 Serie 110 Watt Einfach Ausgang Eingangs Spezifikationen Eingansbereich Frequenz Einschaltstrom 85 VAC bis 264 120 bis 370 VDC 47 - 440 Hz < 18 A Spitze @ 115VAC < 36 A Spitze @ 230VAC Eingangsstrom 2.5A max (RMS) @ 115VAC Wirkungsgrad 70% typisch bei Vollast EMI Filter entspricht FCC Klasse B CISPR 22 Klasse B (einschl. EN55022 Klasse B und VDE 0878 PT3 Klasse B) Electromagnetische Vertraglichkeit entspricht IEC801-2 Level 3, IEC801-4 Level 3 and IEC801-5 Level 3 Leckstrom < 0.5mA @50/60Hz, 264VAC Ausgangs Spezifikationen Maximale 80 W bei Konvektions- kuhlung; Ausgangsleistung 110 W bei 51m3/Std (30 CFM) Luftkuhlung. Einstellbereich 5% minimum Haltezeit Hold-up time 20 ms bei Vollast und 115 VAC Nennspannung Uberlastschutz Kurzschluschutz an allen Ausgangen. Automatische Erholung. Absolute Leistungsgrenze zwischen 110% und 135% uber Spitzennennwert. Uberspannungsschutz 5V Ausgang: 5.7 bis 6.7 VDC. Andere Ausgange 10 bis 25% uber Nennwert; Wiederaufschalten der AC zum Neustart. Umgebungsbedingungen Sicherheit Betriebstemperatur: 0 bis 50C Umgebungstemperatur; Lastminderung um 2.5% / Grad von 50 bis 70C VDE UL CSA NEMKO BABT CB Lagertemperatur: -40 bis 85C Temperaturregulierung: .04% pro C MTBF: > 100,000 Std bei Vollast und 25C Umgebungstemperatur Hinweise zur Produkttabelle 1. Peak Current: Spitzenstrom, Dauer < 30 s mit maximal 10% Arbeitszyklus. 2. Regulation: Bei 25C einschlielich Anlauftoleranzen, Eingangsspannung, Laststrom und Ausgangsspannung in Werkseinstellung. 3. Ripple: Spitze-Spitze mit 20 MHz Bandbreite und 10 F parallel mit einem 0.1 F Kondensator. 4. Maximum Load: Gesamte entnommene Leistung darf 80W Konvetionsund 110W Luftkuhlung nicht uberschreiten. 0805/EN60950 (IEC950) UL1950 CSA 22-2-234 Level 3 EN 60950/EMKO-TUE (74-sec) 203 EN60950/BS7002 Zertifikat und Bericht Dieses Produkt tragt die CE Marke entsprechend der Bestimmung der Low Voltage Directive 73/23/EEC Power OK SK202 pin1 POK 1 pin2 common 2 Power OK Signal;-TTL kompatibles Signal. Wird "High" 50-150ms nach dem Einschalten. Zugehorige Stecker Wird "Low" >1.5 ms vor Verlassen der AC Eingang: GehauseMolex 09-91-0500 (or 26-03-4050) Regelung. DC Ausgang: GehauseMolex 09-91-0900 (or 26-03-4090) Fernabtastung 1 Kontakte: 18/24 AWG Molex 08-50-0106 (or 08-58-0189) SK201 Pin 1 + Sense 2 Fernabtastung:GehauseMolex 22-01-2025 Pin 2 - Sense Kontakte: 22/30 AWG Molex 08-50-0114 Dieses Netzteil verfugt uber einen Fernabtastungsanschluss, mit dem Spannungsabfalle von bis zu 0,5V Hinweise kompensiert werden konnen. Bei 1 Spezifikationsanderung ohne Ankundigug vorbehalten. Nichtverwendung ist die interne Abtastung 2 Alle Mae in mm und (inches). aktiv. Verpolungsschutz ist integriert. 3 Montagebohrung M1 und M2 mu fur EMV-Zecke geerdet sein. Gehause 4 Ausgangsmasse (Common) ist kapazitive mit M2-Erde verbunden. Gehause verfugbar 5 Montagebohrung M1 oder der Flachstecker SK1-3 mu aus Auenmae mit Gehause Geratesicherheitsgrunden mit dem Schutzleiteranschlu 193.5 (7.62) x 115.6 (4.55) x 63 (2.48). verbunden sein. Max.-Leistung im Gehause vermindert sich auf:6 Gewicht: 0.75kg. 70W Konvektion, 90W bei 30CFM Luftkuhlung. Achtung! Beruhrungsgefahrliche Netzspannungen. Absicherung Primarkuhlkorper steht unter Spannung.Beachten sie die Eingangssicherung 4A 20mm flinke HBC beigefugte Bedienungsanleitung. Fur sicheren Betrieb Netzsicherung zum Erhalt des Sicherheitsempfehlen wir das optionale Gehause Kit. standards, nur durch gleichen Typ ersetzen. Order Code Model Nummer LPS112-B LPS113-B LPS114-B LPS115-B LPS118-B Ausgang Minimum Spg. Last 5V 12 V 15 V 24 V 48 V Max. Last mit Konv.-Kuhlung4 0A 0A 0A 0A 0A Max. Last mit 30CFM Luft4 16A 6.7 A 5.3 A 3.3 A 1.7 A 22 A 9.2A 7.3 A 4.6 A 2.3 A Spitzen Last1 25A 10.4A 8.3A 5.2A 2.6A Reglung2 Welligkeit S/S (PARD)3 2% 2% 2% 2% 2% 50 mV 120 mV 150 mV 240 mV 480 mV Zeichnungen 6.35 (0.25) 4.0 (0.156") DIA (4 places) M2 22.6 (0.89) 1 2 3 4 5 6 7 8 9 SK202 SK201 101.6 (4.0) 88.9 (3.5) SK2 63.5 (2.5) 3 GND 2 N 1 108.6 (4.28) Voltage Adjust Pot. SK1 L 22.6 (0.89) M1 165.1 (6.5) 6.35 (0.25) Customer mountings #6-32 bush - 6 places max. penetration 5.0 (0.20) 162.6 (6.4) 11.4 (0.45) 177.8 (7.0) 185.5 (7.3) 56 (2.2) 46.0 (1.8) 21.8 (0.86) 150 (5.9) 2.0 (0.08) Anschlubelegung Connector LPS112-B LPS113-B LPS114-B LPS115-B LPS118-B SK1-1 SK1-2 SK1-3 Line Neutral GND Line Neutral GND Line Neutral GND Line Neutral GND Line Neutral GND SK2-1 SK2-2 SK2-3 SK2-4 SK2-5 SK2-6 SK2-7 SK2-8 SK2-9 +5 V +5 V +5 V Common Common Common Common +5 V +5 V +12 V +12 V +12 V Common Common Common Common +12 V +12 V +15 V +15 V +15 V Common Common Common Common +15 V +15 V +24 V +24 V +24 V Common Common Common Common +24 V +24 V +48V +48V +48V Common Common Common Common +48V +48V SK202 P OK Common SK201-1 SK201-2 SK202-1 SK202-2 1 2 SK201 2 -Sense 1 +Sense +sense -sense POK Common Astec Standard Power Europe Astec House, Waterfront Business Park, Merry Hill, Dudley, West Mids. DY5 1LX, UK. Tel: +44 (0) 1384 842211 Fax: +44 (0) 1384 843355 Astec France S.A.R.L. Les Arcades, 424, la Closerie Mont d'Est, 93194 Noisy Le Grand Cedex, France. Tel: +33 1 4305 8680 Fax:+33 1 4304 6033 Astec Standard Power Germany Robert-Heil-Str. 8, 36251 Bad Hersfeld, Germany Tel: +49 (0) 6621 50570 Fax: +49 (0) 6621 505720 Published by ASPE Ref. No. 00262 A