VTM3 series Voltage Controlled Temperature Compensated Crystal Oscillator Features * Small 3.2x2.5 package size * Clipped Sine Wave Output * Output Frequencies to 45 MHz * Fundamental Crystal Design * Optional VCXO Function available * Gold over nickel contact pads * Hermetically Sealed Ceramic SMD package The VTM3, VCTXCO * Product is compliant to RoHS directive and fully compatible with lead free assembly Applications * GPS * WiMAX, Wi-Fi, Wi-LAN * Seismic Exploration * Point to point radios * Broadband Access * Test Equipment * PDA's Description Vectron's VTM3 Temperature Compensated Crystal Oscillator (TCXO) is a quartz stabilized, clipped sine wave output, temperature compensated oscillator, operating off either 2.8, 3.0, or 3.3 volt supply. Vectron International 267 Lowell Road, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VTM3 Data Sheet Performance Characteristics Table 1. Electrical Performance Parameter Frequency Typical Supply Voltage1 Ordering option, see last page Supply Current 8.000 MHz to < 20.000 MHz 20.000 MHz to < 32.00 MHz 32.000 MHz to 45.00 MHz Output Level2 Output Load Control Voltage Impedance Control Voltage to reach pull All options (3.3,3.0 and 2.8V) Pull Range Ordering option, see last page Temperature Stability Ordering option, see last page. Initial Accuracy, "No Adjust" option Power Supply Stability Load Stability Aging Operating temperature Ordering option, see last page Phase Noise, 12.000MHz 10 Hz offset 100 Hz offset 1 kHz offset 10 kHz offset 100 kHz offset 1 MHz offset 5 MHz offset Start-up time Symbol fO Min 8.000 Typical Maximum 45.000 2.8, 3.0, or 3.3 Units MHz Vdc IDD mA 1.5 2.0 2.5 Vp/p 0.8 ZVc 500 V 10K II 10pf Kohm V 0.5 TPR 2.5 5, 8, 10, 15 ppm 0.5 to 5.0 ppm 0.5 1.0 ppm 0.2 ppm 0.2 ppm 1.0 ppm/year 0/55, -10/60, -20/70, -30/80, -40/85 C dBc/Hz -89 -117 -135 -148 -153 -154 -155 2 1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended. 2. Output is DC coupled. Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com ms VTM3 Data Sheet Figure 2. Clipped Sine Wave Output VCXO Functional Description VCXO Feature: The VTM3 can be ordered with a VCXO function for applications where it will be used in a PLL, or the output frequency needs fine tune adjustments. This is a high impedance input, 0.5 Mohm, and can be driven with an op-amp or terminated with adjustable resistors etc. Pin 1 should not be left floating on the VCXO optional devices. "No Adjust" Feature: In applications where the VTM3 will not be used in a PLL, or the output frequency does not fine tune adjustments, the best device to use would be a VTM3-x0xx. By using the "no adjust" option, the circuit is simplified as Vc does not need to adjusted or set to a predetermined voltage and pin 1 should be grounded (pin 1 can be left open but should not be set to a voltage such as the supply). Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VTM3 Data Sheet Outline Diagrams, Pad Layout and Pin Out Pin 1, Pin 2, Pin 3, Pin 4, Pin 5, Pin 6, Pin 7, Pin 8, Ground or VC NC Ground Output NC VCC NC NC Contact Pads are gold over nickel Devices will be marked with the frequency Pin 2,5,6,7,8 are used to program and adjust the TCXO during manufacturing and should be left open; do not terminate these to the supply voltage and are a "make no connection" pad. Figure 3, Package drawing Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VTM3 Data Sheet 2 .5 0 .2 3.20.2 1.0 max MARKING #1 #2 0.85 0 .65 Pin 1, Ground or VC PinTERMINAL 2, Ground CONNECTION Pin 3, Output TCXO VCTCXO Pin 4, #1 VCC GND Vcont #4 1.95 #2 GND GND #3 OUTPUT OUTPUT #4 Vcc Vcc #3 0.55 1.65 1 .25 1.0 2.6 LAND PATTERN Contact Pads are gold over nickel Devices will be marked with the frequency Figure 4, Package drawing for 0.5ppm over -30/80C and <2ppm over -40/85C Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VTM3 Data Sheet Tape and Reel Table 3. Tape and Reel Dimensions (mm) Tape Dimensions Product A VTM3 8 B C D E 1.75 1.55 4 4 Reel Dimensions F G H 2.5 22 13 I J K L 60 1.75 11.5 178 # Per Reel 1000 J F C D G B A L I E H K Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Table 4. Absolute Maximum Ratings Parameter Symbol Storage Temperature Tstorage Ratings -40/85 Unit C Reliability The VTM3 qualification tests have included: Table 5. Environnemental Compliance Parameter Mechanical Shock Mechanical Vibration Temperature Cycle Solderability Gross and Fine Leak Resistance to Solvents Moisture Sensitivity Level Contact Pads Vectron International 267 Lowell Rd, Hudson NH 03051 Conditions MIL-STD-883 Method 2002 MIL-STD-883 Method 2007 MIL-STD-883 Method 1010 MIL-STD-883 Method 2003 MIL-STD-883 Method 1014 MIL-STD-883 Method 2015 1 Gold over Nickel Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VTM3 Data Sheet Handling Precautions Although ESD protection circuitry has been designed into the the VTM3, proper precautions should be taken when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and therefore can be used for comparison purposes. Table 6. ESD Ratings Model Human Body Model Charged Device Model Minimum 1000 1000 Conditions MIL-STD-883 Method 3115 JESD 22-C101 Suggested IR profile Devices are built using lead free epoxy and can also be subjected to standard lead free IR reflow conditions, Table 7 shows max temperatures and lower temperatures can also be used e.g. peak temperature of 220C. Table 7. Reflow Profile (IPC/JEDEC J-STD-020) Parameter Symbol PreHeat Time tS Ramp Up R UP o Time Above 217 C tL Time To Peak Temperature t AMB-P Time At 260 oC (max) tP Time At 240 C (max) tp2 Ramp Down R DN Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 7 Value 60 sec Min, 180 sec Max 3 oC/sec Max 60 sec Min, 150 sec Max 480 sec Max 10 sec Max 60 sec Max 6 oC/sec Max e-mail vectron@vectron.com VTM3 Data Sheet Ordering Information Table 8. Standard Frequency List 10.000 12.000 12.800 16.367 16.367667 16.367673 19.440 19.6608 19.680 27.456 32.000 39.000 VTM3 - B 13.000 16.368 20.000 0 13.568 16.369 23.104 2 C 14.000 16.376 24.5535 - 14.7456 16.800 25.000 16.000 19.200 26.000 12M800 Product Family Output Frequency TCXO, 3.2 x 2.5 In MHz Voltage Options Temperature Options B: +3.3 Vdc 5%, Clipped Sine Output A: 0 to 55C C: +3.0 Vdc 5%, Clipped Sine Output B: -10 to 60C D: +2.8 Vdc 5%, Clipped Sine Output C: -20 to 70C D: -30 to 80C E: -40 to 85C Pulling Range 0: Fixed TCXO, no adjust Stability Options 1: 5ppm A: 0.5ppm 2: 8ppm 1: 1.0ppm 3: 10ppm B: 1.5ppm 4: 15ppm 2: 2.0ppm C: 2.5ppm 3: 3.0ppm Note: Not all combinations are available D: 3.5ppm 4: 4.0ppm 5: 5.0ppm www.vectron.com Revision 1.0 Date 02/15/08 USA: Vectron International * 267For Lowell Road, Hudson, NH 03051Please Contact: Additional Information, * Tel: 1-88-VECTRON-1 * Fax: 1-888-FAX-VECTRON EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany * Tel: 49 (0) 7268 8010 * Fax: 49 (0) 7268 801281 ASIA: Vectron Asia Pacific Sales 1F~2F. No.8 Workshop No.308 Fenju Rd., WaiGaoQiao Free Trade Zone, Pudong New Area Shanghai, China 200131 *Tel: 8621 50480777 * Fax: 8621 50481881 Date Description Initial Release Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 8 e-mail vectron@vectron.com