AP2122AK-2.8TRE1 - Diodes Incorporated

AP2122

Document number: DS41210 Rev. 2 - 2

1 of 17

www.diodes.com

July 2018

AP2122

HIGH SPEED, EXTREMELY LOW NOISE LDO REGULATOR

Description

The AP2122 series are positive voltage regulator ICs fabricated by

CMOS process. Each of these ICs consists of a voltage reference, an

error amplifier, a resistor network for setting output voltage, a current

limit circuit for current protection and a chip enable circuit.

The AP2122 series feature high ripple rejection, low dropout voltage,

low noise, high output voltage accuracy, and low current consumption

which make them ideal for use in various battery-powered devices.

The AP2122 series have 1.5V, 1.8V, 2.5V, 2.8V, 3.0V, 3.2V and 3.3V

versions.

The AP2122 are available in standard SOT-23-5 package.

Features

 Low Dropout Voltage at IOUT = 100mA: 150mV Typical (Except

1.5V Version)

 Low Standby Current: 0.1µA Typical

 Low Quiescent Current: 25µA Typical

 High Ripple Rejection: 70dB Typical (f = 10kHz)

 Maximum Output Current: More Than 150mA (300mA Limit)

 Extremely Low Noise: 30µVrms (10Hz to 100kHz)

 Excellent Line Regulation: 4mV Typical

 Excellent Load Regulation: 12mV Typical

 High Output Voltage Accuracy: ±2%

 Excellent Line and Load Transient Response

 Compatible with Low ESR Ceramic Capacitor (as Low as 1µF)

Pin Assignments

(Top View)

1

2

3 4

5

VOUT

GND

VIN

NC

CE

SOT-23-5

Applications

 Mobile Phones, Cordless Phones

 MP3/4

 Portable Electronic Devices

 Cameras, Video Recorders

 Sub-board Power Supplies for Telecom Equipment

 Battery Powered Equipment

Typical Applications Circuit (Note 1)

Note 1: Filter capacitors are required at the AP2122's input and output. 1µF capacitor is required at the input. The minimum output capacitance required for stability

should be more than 1µF with ESR from 0.01Ω to 100Ω. Ceramic capacitors are recommended.

AP2122

Document number: DS41210 Rev. 2 - 2

2 of 17

www.diodes.com

July 2018

AP2122

Pin Descriptions

Pin Number

Pin Name

Function

1

VOUT

Regulated output voltage

2

GND

Ground

3

VIN

Input voltage

4

CE

Active high enable input pin. Logic high=enable, logic low=shutdown

5

NC

No connection

Functional Block Diagram

AP2122

Document number: DS41210 Rev. 2 - 2

3 of 17

www.diodes.com

July 2018

AP2122

Absolute Maximum Ratings (Note 2)

Symbol

Parameter

Rating

Unit

VIN

Input Voltage

6.5

V

VCE

Enable Input Voltage

-0.3 to VIN +0.3

V

IOUT

Output Current

300

mA

TJ

Junction Temperature

+150

°C

TSTG

Storage Temperature Range

-65 to +150

°C

TLEAD

Lead Temperature (Soldering, 10sec)

+260

°C

JA

Thermal Resistance (Note 3)

250

°C/W

ESD

ESD (Human Body Model)

2000

V

ESD

ESD (Machine Model)

200

V

Notes: 2. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Conditions” is not implied.

Exposure to “Absolute Maximum Ratings” for extended periods may affect device reliability.

3. Absolute maximum ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the

device outside of its operating ratings. The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(max), the junction-to-

ambient thermal resistance, JA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated

using: PD(max)=(TJ(max) -TA)/ JA. Exceeding the maximum allowable power dissipation will result in excessive die temperature.

Recommended Operating Conditions

Symbol

Parameter

Min

Max

Unit

VIN

Input Voltage

2

6

V

TJ

Operating Junction Temperature Range

-40

+85

°C

AP2122

Document number: DS41210 Rev. 2 - 2

4 of 17

www.diodes.com

July 2018

AP2122

Electrical Characteristics

AP2122-1.5 Electrical Characteristics (@VIN = 2.5V, TJ = +25°C, CIN = 1µF, COUT = 1µF, Bold typeface applies over -40°C ≤

T

J ≤ +85°C, unless otherwise specified.)

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

VOUT

Output Voltage

VIN = 2.5V

1mA ≤ IOUT ≤ 30mA

1.47

1.5

1.53

V

VIN

Input Voltage

—

6

V

IOUT

Output Current

VIN-VOUT = 1V

150

—

mA

VRLOAD

Load Regulation

VIN = 2.5V

1mA ≤ IOUT ≤ 80mA

—

12

40

mV

VRLINE

Line Regulation

2.3V ≤ VIN ≤ 6V

IOUT = 30mA

—

4

16

mV

VDROP

Dropout Voltage

IOUT = 10mA

—

400

600

mV

IOUT = 100mA

—

400

600

IOUT = 150mA

—

400

600

IQ

Quiescent Current

VIN = 2.5V, IOUT = 0mA

—

25

50

µA

ISTD

Standby Current

VIN = 2.5V

VCE in OFF Mode

—

0.1

1

µA

PSRR

Power Supply Rejection Ratio

Ripple 0.5Vp-p, f = 10kHz

VIN = 2.5V

—

70

—

dB

∆VOUT/∆T

Output Voltage

Temperature Coefficient

IOUT = 30mA

—

±150

—

µV/°C

(∆VOUT/VOUT)/∆T

—

±100

—

ppm/°C

ILIMIT

Short Current Limit

VOUT = 0V

—

50

—

mA

VNOISE

RMS Output Noise

TA = +25°C

10Hz ≤ f ≤ 100kHz

—

30

—

µVrms

—

CE "High" Voltage

CE Input Voltage "High"

1.5

—

V

—

CE "Low" Voltage

CE Input Voltage "Low"

—

0.25

V

RPD

CE Pull-down Internal

Resistance

—

2.5

5

10

MΩ

JC

Thermal Resistance

(Junction to Case)

SOT-23-5

—

73.9

—

°C/W

AP2122

Document number: DS41210 Rev. 2 - 2

5 of 17

www.diodes.com

July 2018

AP2122

Electrical Characteristics (Cont.)

AP2122-1.8 Electrical Characteristics (@VIN = 2.8V, TJ = +25°C, CIN = 1µF, COUT = 1µF, Bold typeface applies over -40°C ≤

T

J ≤ +85°C, unless otherwise specified.)

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

VOUT

Output Voltage

VIN = 2.8V

1mA ≤ IOUT ≤ 30mA

1.764

1.8

1.836

V

VIN

Input Voltage

—

6

V

IOUT

Output Current

VIN-VOUT = 1V

150

—

mA

VRLOAD

Load Regulation

VIN = 2.8V

1mA ≤ IOUT ≤ 80mA

—

12

40

mV

VRLINE

Line Regulation

2.3V ≤ VIN ≤ 6V

IOUT = 30mA

—

4

16

mV

VDROP

Dropout Voltage

IOUT = 10mA

—

20

40

mV

IOUT = 100mA

—

150

300

IOUT = 150mA

—

200

400

IQ

Quiescent Current

VIN = 2.8V, IOUT = 0mA

—

25

50

µA

ISTD

Standby Current

VIN = 2.8V

VCE in OFF Mode

—

0.1

1

µA

PSRR

Power Supply Rejection Ratio

Ripple 0.5Vp-p, f = 10kHz

VIN = 2.8V

—

70

—

dB

∆VOUT/∆T

Output Voltage

Temperature Coefficient

IOUT = 30mA

—

±180

—

µV/°C

(∆VOUT/VOUT)/∆T

—

±100

—

ppm/°C

ILIMIT

Short Current Limit

VOUT = 0V

—

50

—

mA

VNOISE

RMS Output Noise

TA = +25°C

10Hz ≤ f ≤ 100kHz

—

30

—

µVrms

—

CE "High" Voltage

CE Input Voltage "High"

1.5

—

V

—

CE "Low" Voltage

CE Input Voltage "Low"

—

0.25

V

RPD

CE Pull-down Internal

Resistance

—

2.5

5

10

MΩ

JC

Thermal Resistance

(Junction to Case)

SOT-23-5

—

73.9

—

°C/W

AP2122

Document number: DS41210 Rev. 2 - 2

6 of 17

www.diodes.com

July 2018

AP2122

Electrical Characteristics (Cont.)

AP2122-2.5 Electrical Characteristics (@VIN = 3.5V, TJ = +25°C, CIN = 1µF, COUT = 1µF, Bold typeface applies over -40°C ≤

T

J ≤ +85°C, unless otherwise specified.)

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

VOUT

Output Voltage

VIN = 3.5V

1mA ≤ IOUT ≤ 30mA

2.45

2.5

2.55

V

VIN

Input Voltage

—

6

V

IOUT

Output Current

VIN-VOUT = 1V

150

—

mA

VRLOAD

Load Regulation

VIN = 3.5V

1mA ≤ IOUT ≤ 80mA

—

12

40

mV

VRLINE

Line Regulation

3V ≤ VIN ≤ 6V

IOUT = 30mA

—

4

16

mV

VDROP

Dropout Voltage

IOUT = 10mA

—

20

40

mV

IOUT = 100mA

—

150

300

IOUT = 150mA

—

200

400

IQ

Quiescent Current

VIN = 3.5V, IOUT = 0mA

—

25

50

µA

ISTD

Standby Current

VIN = 3.5V

VCE in OFF Mode

—

0.1

1

µA

PSRR

Power Supply Rejection Ratio

Ripple 0.5Vp-p, f = 10kHz

VIN = 3.5V

—

70

—

dB

∆VOUT/∆T

Output Voltage

Temperature Coefficient

IOUT = 30mA

—

±250

—

µV/°C

(∆VOUT/VOUT)/∆T

—

±100

—

ppm/°C

ILIMIT

Short Current Limit

VOUT = 0V

—

50

—

mA

VNOISE

RMS Output Noise

TA = +25°C

10Hz ≤ f ≤ 100kHz

—

30

—

µVrms

—

CE "High" Voltage

CE Input Voltage "High"

1.5

—

V

—

CE "Low" Voltage

CE Input Voltage "Low"

—

0.25

V

RPD

CE Pull-down Internal

Resistance

—

2.5

5

10

MΩ

JC

Thermal Resistance

(Junction to Case)

SOT-23-5

—

73.9

—

°C/W

AP2122

Document number: DS41210 Rev. 2 - 2

7 of 17

www.diodes.com

July 2018

AP2122

Electrical Characteristics (Cont.)

AP2122-2.8 Electrical Characteristics (@VIN = 3.8V, TJ = +25°C, CIN = 1µF, COUT = 1µF, Bold typeface applies over -40°C ≤

T

J ≤ +85°C, unless otherwise specified.)

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

VOUT

Output Voltage

VIN = 3.8V

1mA ≤ IOUT ≤ 30mA

2.744

2.8

2.856

V

VIN

Input Voltage

—

6

V

IOUT

Output Current

VIN-VOUT = 1V

150

—

mA

VRLOAD

Load Regulation

VIN = 3.8V

1mA ≤ IOUT ≤ 80mA

—

12

40

mV

VRLINE

Line Regulation

3.3V ≤ VIN ≤ 6V

IOUT = 30mA

—

4

16

mV

VDROP

Dropout Voltage

IOUT = 10mA

—

20

40

mV

IOUT = 100mA

—

150

300

IOUT = 150mA

—

200

400

IQ

Quiescent Current

VIN = 3.8V, IOUT = 0mA

—

25

50

µA

ISTD

Standby Current

VIN = 3.8V

VCE in OFF Mode

—

0.1

1

µA

PSRR

Power Supply Rejection Ratio

Ripple 0.5Vp-p, f = 10kHz

VIN = 3.8V

—

70

—

dB

∆VOUT/∆T

Output Voltage

Temperature Coefficient

IOUT = 30mA

—

±280

—

µV/°C

(∆VOUT/VOUT)/∆T

—

±100

—

ppm/°C

ILIMIT

Short Current Limit

VOUT = 0V

—

50

—

mA

VNOISE

RMS Output Noise

TA = +25°C

10Hz ≤ f ≤ 100kHz

—

30

—

µVrms

—

CE "High" Voltage

CE Input Voltage "High"

1.5

—

V

—

CE "Low" Voltage

CE Input Voltage "Low"

—

0.25

V

RPD

CE Pull-down Internal

Resistance

—

2.5

5

10

MΩ

JC

Thermal Resistance

(Junction to Case)

SOT-23-5

—

73.9

—

°C/W

AP2122

Document number: DS41210 Rev. 2 - 2

8 of 17

www.diodes.com

July 2018

AP2122

Electrical Characteristics (Cont.)

AP2122-3.0 Electrical Characteristics (@VIN = 4V, TJ = +25°C, CIN = 1µF, COUT = 1µF, Bold typeface applies over -40°C ≤

T

J ≤ +85°C, unless otherwise specified.)

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

VOUT

Output Voltage

VIN = 4V

1mA ≤ IOUT ≤ 30mA

2.94

3.0

3.06

V

VIN

Input Voltage

—

6

V

IOUT

Output Current

VIN-VOUT = 1V

150

—

mA

VRLOAD

Load Regulation

VIN = 4V

1mA ≤ IOUT ≤ 80mA

—

12

40

mV

VRLINE

Line Regulation

3.5V ≤ VIN ≤ 6V

IOUT = 30mA

—

4

16

mV

VDROP

Dropout Voltage

IOUT = 10mA

—

20

40

mV

IOUT = 100mA

—

150

300

IOUT = 150mA

—

200

400

IQ

Quiescent Current

VIN = 4V, IOUT = 0mA

—

25

50

µA

ISTD

Standby Current

VIN = 4V

VCE in OFF Mode

—

0.1

1

µA

PSRR

Power Supply Rejection Ratio

Ripple 0.5Vp-p, f = 10kHz

VIN = 4V

—

70

—

dB

∆VOUT/∆T

Output Voltage

Temperature Coefficient

IOUT = 30mA

—

±300

—

µV/°C

(∆VOUT/VOUT)/∆T

—

±100

—

ppm/°C

ILIMIT

Short Current Limit

VOUT = 0V

—

50

—

mA

VNOISE

RMS Output Noise

TA = +25°C

10Hz ≤ f ≤ 100kHz

—

30

—

µVrms

—

CE "High" Voltage

CE Input Voltage "High"

1.5

—

V

—

CE "Low" Voltage

CE Input Voltage "Low"

—

0.25

V

RPD

CE Pull-down Internal

Resistance

—

2.5

5

10

MΩ

JC

Thermal Resistance

(Junction to Case)

SOT-23-5

—

73.9

—

°C/W

AP2122

Document number: DS41210 Rev. 2 - 2

9 of 17

www.diodes.com

July 2018

AP2122

Electrical Characteristics (Cont.)

AP2122-3.2 Electrical Characteristics (@VIN = 4.2V, TJ = +25°C, CIN = 1µF, COUT = 1µF, Bold typeface applies over -40°C ≤

T

J ≤ +85°C, unless otherwise specified.)

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

VOUT

Output Voltage

VIN = 4.2V

1mA ≤ IOUT ≤ 30mA

3.136

3.2

3.264

V

VIN

Input Voltage

—

6

V

IOUT

Output Current

VIN-VOUT = 1V

150

—

mA

VRLOAD

Load Regulation

VIN = 4.2V

1mA ≤ IOUT ≤ 80mA

—

12

40

mV

VRLINE

Line Regulation

3.7V ≤ VIN ≤ 6V

IOUT = 30mA

—

4

16

mV

VDROP

Dropout Voltage

IOUT = 10mA

—

20

40

mV

IOUT = 100mA

—

150

300

IOUT = 150mA

—

200

400

IQ

Quiescent Current

VIN = 4.2V, IOUT = 0mA

—

25

50

µA

ISTD

Standby Current

VIN = 4.2V

VCE in OFF Mode

—

0.1

1

µA

PSRR

Power Supply Rejection Ratio

Ripple 0.5Vp-p, f = 10kHz

VIN = 4.2V

—

70

—

dB

∆VOUT/∆T

Output Voltage

Temperature Coefficient

IOUT = 30mA

—

±320

—

µV/°C

(∆VOUT/VOUT)/∆T

—

±100

—

ppm/°C

ILIMIT

Short Current Limit

VOUT = 0V

—

50

—

mA

VNOISE

RMS Output Noise

TA = +25°C

10Hz ≤ f ≤ 100kHz

—

30

—

µVrms

—

CE "High" Voltage

CE Input Voltage "High"

1.5

—

V

—

CE "Low" Voltage

CE Input Voltage "Low"

—

0.25

V

RPD

CE Pull-down Internal

Resistance

—

2.5

5

10

MΩ

JC

Thermal Resistance

(Junction to Case)

SOT-23-5

—

73.9

—

°C/W

AP2122

Document number: DS41210 Rev. 2 - 2

10 of 17

www.diodes.com

July 2018

AP2122

Electrical Characteristics (Cont.)

AP2122-3.3 Electrical Characteristics (@VIN = 4.3V, TJ = +25°C, CIN = 1µF, COUT = 1µF, Bold typeface applies over -40°C ≤

T

J ≤ +85°C, unless otherwise specified.)

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

VOUT

Output Voltage

VIN = 4.3V

1mA ≤ IOUT ≤ 30mA

3.234

3.3

3.366

V

VIN

Input Voltage

—

6

V

IOUT

Output Current

VIN-VOUT = 1V

150

—

mA

VRLOAD

Load Regulation

VIN = 4.3V

1mA ≤ IOUT ≤ 80mA

—

12

40

mV

VRLINE

Line Regulation

3.8V ≤ VIN ≤ 6V

IOUT = 30mA

—

4

16

mV

VDROP

Dropout Voltage

IOUT = 10mA

—

20

40

mV

IOUT = 100mA

—

150

300

IOUT = 150mA

—

200

400

IQ

Quiescent Current

VIN = 4.3V, IOUT = 0mA

—

25

50

µA

ISTD

Standby Current

VIN = 4.3V

VCE in OFF Mode

—

0.1

1

µA

PSRR

Power Supply Rejection Ratio

Ripple 0.5Vp-p, f = 10kHz

VIN = 4.3V

—

70

—

dB

∆VOUT/∆T

Output Voltage

Temperature Coefficient

IOUT = 30mA

—

±330

—

µV/°C

(∆VOUT/VOUT)/∆T

—

±100

—

ppm/°C

ILIMIT

Short Current Limit

VOUT = 0V

—

50

—

mA

VNOISE

RMS Output Noise

TA = +25°C

10Hz ≤ f ≤ 100kHz

—

30

—

µVrms

—

CE "High" Voltage

CE Input Voltage "High"

1.5

—

V

—

CE "Low" Voltage

CE Input Voltage "Low"

—

0.25

V

RPD

CE Pull-down Internal

Resistance

—

2.5

5

10

MΩ

JC

Thermal Resistance

(Junction to Case)

SOT-23-5

—

73.9

—

°C/W

AP2122

Document number: DS41210 Rev. 2 - 2

11 of 17

www.diodes.com

July 2018

AP2122

Performance Characteristics

Output Voltage vs. Output Current Output Voltage vs. Output Current

Output Voltage vs. Input Voltage Output Voltage vs. Input Voltage

Dropout Voltage vs. Output Current Dropout Voltage vs. Output Current

050 100 150 200 250 300 350

0.0

0.3

0.6

0.9

1.2

1.5

Output Voltage (V)

Output Current (mA)

AP2122-1.5

VIN=2.0V

VIN=2.5V

VIN=3.0V

050 100 150 200 250 300 350

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

Output Voltage (V)

Output Current (mA)

AP2122-3.0

VIN=3.3V

VIN=4V

VIN=6V

0 1 2 3 4 5 6 7

0.00

0.25

0.50

0.75

1.00

1.25

1.50

Output Voltage (V)

Input Voltage (V)

AP2122-1.5

IOUT=30mA

0 1 2 3 4 5 6 7

2.00

2.25

2.50

2.75

3.00

3.25

3.50

Output Voltage (V)

Input Voltage (V)

AP2122-3.0

IOUT=30mA

040 80 120 160 200

0.0

0.1

0.2

0.3

0.4

0.5

0.6

Minimum Operating Requirement

Dropout Voltage (V)

Output Current (mA)

AP2122-1.5

040 80 120 160 200

0.0

0.1

0.2

0.3

0.4

0.5

0.6

Dropout Voltage (V)

Output Current (mA)

AP2122-3.0

AP2122

Document number: DS41210 Rev. 2 - 2

12 of 17

www.diodes.com

July 2018

AP2122

Performance Characteristics (Cont.)

Output Voltage vs. Junction Temperature Output Voltage vs. Junction Temperature

Supply Current vs. Input Voltage Supply Current vs. Input Voltage

Supply Current vs. Junction Temperature Supply Current vs. Junction Temperature

-25 0 25 50 75 100 125

1.40

1.42

1.44

1.46

1.48

1.50

1.52

1.54

1.56

1.58

1.60

AP2122-1.5

VIN=2.5V

IOUT=30mA

Output Voltage (V)

Junction Temperature (oC)

-25 0 25 50 75 100 125

2.90

2.92

2.94

2.96

2.98

3.00

3.02

3.04

3.06

3.08

3.10

AP2122-3.0

VIN=4V

IOUT=30mA

Output Voltage (V)

Junction Temperature (oC)

0 1 2 3 4 5 6 7

0

10

20

30

40

50

60

AP2122-1.5

IOUT=0mA

Supply Current (A)

Input Voltage (V)

0 1 2 3 4 5 6 7

0

10

20

30

40

50

60

Supply Current (A)

Input Voltage (V)

AP2122-3.0

IOUT=0mA

-25 0 25 50 75 100 125

0

5

10

15

20

25

30

35

40

Supply Current (A)

Junction Temperature (oC)

AP2122-1.5

VIN=2.5V

IOUT=0mA

-25 0 25 50 75 100 125

0

5

10

15

20

25

30

35

40

Supply Current (A)

Junction Temperature (oC)

AP2122-3.0

VIN=4V

IOUT=0mA

AP2122

Document number: DS41210 Rev. 2 - 2

13 of 17

www.diodes.com

July 2018

AP2122

Performance Characteristics (Cont.)

Line Transient Line Transient

(Conditions: IOUT=30mA, CIN=1µF, COUT=1µF) (Conditions: IOUT=30mA, CIN=1µF, COUT=1µF)

Load Transient Load Transient

(Conditions: VIN=2.5V, CIN=1µF, COUT=1µF) (Conditions: VIN=4V, CIN=1µF, COUT=1µF)

PSRR vs. Frequency PSRR vs. Frequency

10 100 1k 10k 100k 1M

0

20

40

60

80

100

PSRR (dB)

Frequency (Hz)

AP2122-1.5

VIN=2.5V

IOUT=30mA

CIN=COUT=1F

10 100 1k 10k 100k

0

10

20

30

40

50

60

70

80

90

100

PSRR (dB)

Frequency (Hz)

AP2122-3.0

VIN=4V

IOUT=30mA

CIN=COUT=1F

AP2122-1.5

5.5

4.5

3.5

2.5

0.05

0

-0.05

-0.1

Time (40µs/Div)

VIN (1V/Div)

∆VOUT (0.05V/Div)

VIN (1V/Div)

7

6

5

4

0.05

0

-0.05

-0.1

∆VOUT (0.05V/Div)

Time (20µs/Div)

AP2122-3.0

1.7

1.6

1.5

1.4

100

50

0

-50

VOUT (0.1V/Div)

IOUT (50mA/Div)

Time (200µs/Div)

AP2122-1.5

Time (200µs/Div)

AP2122-3.0

3.2

3.1

3.0

2.9

200

100

0

-100

VOUT (0.1V/Div)

IOUT (100mA/Div)

AP2122

Document number: DS41210 Rev. 2 - 2

14 of 17

www.diodes.com

July 2018

AP2122

Ordering Information

AP2122 X X - X X X

Packing

Package TR : Tape & Reel

K : SOT-23-5

Product Name E1/G1

E1 : RoHS Compliant

G1 : RoHS Compliant

and Green

Condition

1.5 : Fixed Output 1.5V

Output Voltage

A : Active High

(Pull-down resistor

built-in) 1.8 : Fixed Output 1.8V

2.5 : Fixed Output 2.5V

2.8 : Fixed Output 2.8V

3.0 : Fixed Output 3.0V

3.2 : Fixed Output 3.2V

3.3 : Fixed Output 3.3V

Package

Temperature

Range

Condition

Part Number

Marking ID

Packing

RoHS

Compliant

RoHS Compliant

and Green

RoHS

Compliant

RoHS Compliant

and Green

SOT-23-5

-40 to +85°C

Active High (Pull-down

resistor built-in)

AP2122AK-

1.5TRE1

AP2122AK-

1.5TRG1

E2Z

G2Z

Tape & Reel

Active High (Pull-down

resistor built-in)

AP2122AK-

1.8TRE1

AP2122AK-

1.8TRG1

E2U

G2U

Tape & Reel

Active High (Pull-down

resistor built-in)

AP2122AK-

2.5TRE1

AP2122AK-

2.5TRG1

E2V

G2V

Tape & Reel

Active High (Pull-down

resistor built-in)

AP2122AK-

2.8TRE1

AP2122AK-

2.8TRG1

E2W

G2W

Tape & Reel

Active High (Pull-down

resistor built-in)

AP2122AK-

3.0TRE1

AP2122AK-

3.0TRG1

E2X

G2X

Tape & Reel

Active High (Pull-down

resistor built-in)

AP2122AK-

3.2TRE1

AP2122AK-

3.2TRG1

E3Y

G3Y

Tape & Reel

Active High (Pull-down

resistor built-in)

AP2122AK-

3.3TRE1

AP2122AK-

3.3TRG1

E2Y

G2Y

Tape & Reel

AP2122

Document number: DS41210 Rev. 2 - 2

15 of 17

www.diodes.com

July 2018

AP2122

Package Outline Dimensions (All dimensions in mm(inch).)

(1) Package Type: SOT-23-5

2.820(0.111)

2.650(0.104)

1.500(0.059)

0.000(0.000)

0.300(0.012)

0.950(0.037)

0.900(0.035)

0.100(0.004)

0.200(0.008)

0.300(0.012)

8°

0°

3.100(0.122)

1.700(0.067)

3.000(0.118)

0.500(0.020)

0.150(0.006)

1.300(0.051)

0.200(0.008)

0.600(0.024)

1.800(0.071)

2.000(0.079)

0.700(0.028)

REF

TYP

1.450(0.057)

MAX

AP2122

Document number: DS41210 Rev. 2 - 2

16 of 17

www.diodes.com

July 2018

AP2122

Suggested Pad Layout

(1) Package Type: SOT-23-5

E2

E1

Y

X

GZ

Dimensions

Z

(mm)/(inch)

G

(mm)/(inch)

X

(mm)/(inch)

Y

(mm)/(inch)

E1

(mm)/(inch)

E2

(mm)/(inch)

Value

3.600/0.142

1.600/0.063

0.700/0.028

1.000/0.039

0.950/0.037

1.900/0.075

AP2122

Document number: DS41210 Rev. 2 - 2

17 of 17

www.diodes.com

July 2018

AP2122

IMPORTANT NOTICE

DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).

Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes

without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the

application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or

trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume

all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated

website, harmless against all damages.

Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.

Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and

hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or

indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.

Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings

noted herein may also be covered by one or more United States, international or foreign trademarks.

This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the

final and determinative format released by Diodes Incorporated.

LIFE SUPPORT

Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express

written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:

A. Life support devices or systems are devices or systems which:

1. are intended to implant into the body, or

2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the

labeling can be reasonably expected to result in significant injury to the user.

B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the

failure of the life support device or to affect its safety or effectiveness.

Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any

use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related

information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its

representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.

www.diodes.com

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Diodes Incorporated:

AP2122AK-1.5TRE1 AP2122AK-1.8TRE1 AP2122AK-2.5TRE1 AP2122AK-2.8TRE1 AP2122AK-3.0TRE1

AP2122AK-3.2TRE1 AP2122AK-3.3TRE1