LT4356HDE-3#TRPBF - Linear Technology

LT4356-3

43563fb

APPLICATIONS

FEATURES DESCRIPTION

Surge Stopper with

Fault Latchoff

The LT

4356-3 surge stopper protects loads from high

voltage transients. It regulates the output during an

overvoltage event, such as load dump in automobiles,

by controlling the gate of an external N-channel MOSFET.

The output is limited to a safe value thereby allowing the

loads to continue functioning. The LT4356-3 also monitors

the voltage drop between the VCC and SNS pins to protect

against overcurrent faults. An internal ampliﬁer limits

the current sense voltage to 50mV. In either fault condi-

tion, a timer is started inversely proportional to MOSFET

stress. If the timer expires, the F LT pin pulls low to warn

of an impending power down. If the condition persists,

the MOSFET is turned off, until the SHDN pin pulls low

momentarily.

The auxiliary ampliﬁer may be used as a voltage detection

comparator or as a linear regulator controller driving an

external PNP pass transistor.

Back-to-back FETs can be used in lieu of a Schottky diode

for reverse input protection, reducing voltage drop and

power loss. The SHDN input turns off the part, including

the auxiliary ampliﬁer, and reduces the quiescent current

to less than 7µA.

n Automotive/Avionic Surge Protection

n Hot Swap/Live Insertion

n High Side Switch for Battery Powered Systems

n Intrinsic Safety Applications

n Stops High Voltage Surges

n Adjustable Output Clamp Voltage

n Overcurrent Protection

n Wide Operation Range: 4V to 80V

n Reverse Input Protection to –60V

n Low 7µA Shutdown Current

n Adjustable Latchoff Fault Timer

n Controls N-channel MOSFET

n Shutdown Pin Withstands –60V to 100V

n Fault Output Indication

n Auxiliary Ampliﬁer for Level Detection Comparator or

Linear Regulator Controller

n Available in (4mm × 3mm) 12-Pin DFN,

10-Pin MSOP or 16-Pin SO Packages

4A, 12V Overvoltage Output Regulator Overvoltage Protector Regulates Output at

27V During Transient

0.1µF

10Ω

10mΩ

IRLR2908

VIN

12V

43563 TA01

LT4356DE-3

GND TMR

OUTGATESNS

IN+

SHDN

AOUT FAULT

VOUT

FLTUNDERVOLTAGE

VCC

DC-DC

CONVERTER

GND

SHDN

VCC

4.99k

383k

100k

102k

100ms/DIV LT4356-3TA01b

VIN

20V/DIV

VOUT

20V/DIV

80V INPUT SURGE CTMR = 6.8µF

ILOAD = 500mA

27V ADJUSTABLE CLAMP

12V

TYPICAL APPLICATION

L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and

Hot Swap, No RSENSE and ThinSOT are trademarks of Linear Technology Corporation. All other

trademarks are the property of their respective owners.

LT4356-3

43563fb

VCC, SHDN ................................................ –60V to 100V

SNS ............................. VCC – 30V or –60V to VCC + 0.3V

OUT, AOUT, F LT , EN ..................................... –0.3V to 80V

GATE (Note 3) .................................–0.3V to VOUT + 10V

FB, TMR, IN+ ................................................ –0.3V to 6V

AOUT, EN, F LT , IN+ ..................................................–3mA

Operating Temperature Range

LT4356C-3 ............................................... 0°C to 70°C

LT4356I-3 ............................................ –40°C to 85°C

IN+

AOUT

GND

FLT

SHDN

TMR

OUT

GATE

SNS

VCC

TOP VIEW

DE PACKAGE

12-LEAD (4mm × 3mm) PLASTIC DFN

TJMAX = 125°C, θJA = 43°C/W

EXPOSED PAD (PIN 13) PCB GND CONNECTION OPTIONAL

OUT

GATE

SNS

VCC

TMR

GND

FLT

SHDN

TOP VIEW

MS PACKAGE

10-LEAD PLASTIC MSOP

TJMAX = 125°C, θJA = 160°C/W

TOP VIEW

S PACKAGE

16-LEAD PLASTIC SO

TMR

OUT

GATE

SNS

VCC

IN+

AOUT

GND

FLT

SHDN

TJMAX = 150°C, θJA = 100°C/W

LT4356H-3 ......................................... –40°C to 125°C

LT4356MP-3 ...................................... –55°C to 125°C

Storage Temperature Range

DE12 .................................................. –65°C to 125°C

MS, SO .............................................. –65°C to 150°C

Lead Temperature (Soldering, 10 sec)

MS, SO ............................................................. 300°C

ABSOLUTE MAXIMUM RATINGS

PIN CONFIGURATION

(Notes 1 and 2)

ORDER INFORMATION

LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE

LT4356CDE-3#PBF LT4356CDE-3#TRPBF 43563 12-Lead (4mm × 3mm) Plastic DFN 0°C to 70°C

LT4356IDE-3#PBF LT4356IDE-3#TRPBF 43563 12-Lead (4mm × 3mm) Plastic DFN –40°C to 85°C

LT4356HDE-3#PBF LT4356HDE-3#TRPBF 43563 12-Lead (4mm × 3mm) Plastic DFN –40°C to 125°C

LT4356CMS-3#PBF LT4356CMS-3#TRPBF LTFFK 10-Lead Plastic MSOP 0°C to 70°C

LT4356IMS-3#PBF LT4356IMS-3#TRPBF LTFFK 10-Lead Plastic MSOP –40°C to 85°C

LT4356HMS-3#PBF LT4356HMS-3#TRPBF LTFFK 10-Lead Plastic MSOP –40°C to 125°C

LT4356MPMS-3#PBF LT4356MPMS-3#TRPBF LTGGZ 10-Lead Plastic MSOP –55°C to 125°C

LT4356CS-3#PBF LT4356CS-3#TRPBF LT4356S-3 16-Lead Plastic SO 0°C to 70°C

LT4356IS-3#PBF LT4356IS-3#TRPBF LT4356S-3 16-Lead Plastic SO –40°C to 85°C

LT4356HS-3#PBF LT4356HS-3#TRPBF LT4356S-3 16-Lead Plastic SO –40°C to 125°C

LT4356MPS-3#PBF LT4356MPS-3#TRPBF LT4356MPS-3 16-Lead Plastic SO –55°C to 125°C

LEAD BASED FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE

LT4356CDE-3 LT4356CDE-3#TR 43563 12-Lead (4mm × 3mm) Plastic DFN 0°C to 70°C

LT4356IDE-3 LT4356IDE-3#TR 43563 12-Lead (4mm × 3mm) Plastic DFN –40°C to 85°C

LT4356HDE-3 LT4356HDE-3#TR 43563 12-Lead (4mm × 3mm) Plastic DFN –40°C to 125°C

LT4356-3

43563fb

The l denotes the speciﬁcations which apply over the full operating

temperature range, otherwise speciﬁcations are at TA = 25°C. VCC = 12V unless otherwise noted.

ELECTRICAL CHARACTERISTICS

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS

VCC Operating Voltage Range l4 80 V

ICC VCC Supply Current VSHDN = Float l1 1.5 mA

VSHDN = 0V, IN+ = 1.3V

LT4356C, LT4356I

LT4356H, LT4356MP

µA

IRReverse Input Current VSNS = VCC = –30V, SHDN Open

VSNS = VCC = VSHDN = –30V

0.3

0.8

ΔVGATE GATE Pin Output High Voltage VCC = 4V; (VGATE – VOUT)

80V ≥ VCC ≥ 8V; (VGATE – VOUT)

4.5

IGATE(UP) GATE Pin Pull-Up Current VGATE = 12V; VCC = 12V; LT4356C, LT4356I, LT4356H

VGATE = 12V; VCC = 12V; LT4356MP

VGATE = 48V; VCC = 48V

–4

–4.5

–23

–30

–36

–38

–50

µA

IGATE(DN) GATE Pin Pull-Down Current Overvoltage, VFB = 1.4V, VGATE = 12V

Overcurrent, VCC – VSNS = 120mV, VGATE = 12V

Shutdown Mode, VSHDN = 0V, VGATE = 12V

1.5

150

VFB FB Pin Servo Voltage VGATE = 12V, VOUT = 12V; LT4356C, LT4356I

VGATE = 12V, VOUT = 12V; LT4356H, LT4356MP

1.225

1.215

1.25

1.275

IFB FB Pin Input Current VFB = 1.25V l0.3 1 µA

ΔVSNS Overcurrent Fault Threshold ΔVSNS = (VCC – VSNS), VCC = 12V; LT4356C, LT4356I

ΔVSNS = (VCC – VSNS), VCC = 12V; LT4356H

ΔVSNS = (VCC – VSNS), VCC = 12V; LT4356MP

ΔVSNS = (VCC – VSNS), VCC = 48V; LT4356C, LT4356I

ΔVSNS = (VCC – VSNS), VCC = 48V; LT4356H

ΔVSNS = (VCC – VSNS), VCC = 48V; LT4356MP

42.5

ISNS SNS Pin Input Current VSNS = VCC = 12V to 48V l5 10 22 µA

ILEAK F LT , EN Pins Leakage Current

AOUT Pin Leakage Current

F LT , EN = 80V

AOUT = 80V

l2.5

4.5

µA

ITMR TMR Pin Pull-up Current VTMR = 1V, VFB = 1.5V, (VCC – VOUT) = 0.5V

VTMR = 1V, VFB = 1.5V, (VCC – VOUT) = 75V

VTMR = 1.3V, VFB = 1.5V, (VCC – VOUT) = 75V

VTMR = 1V, ΔVSNS = 60mV, (VCC – VOUT) = 0.5V

VTMR = 1V, ΔVSNS = 60mV, (VCC – VOUT) = 80V

–1.5

–44

–3.5

–2.5

–195

–2.5

–50

–5.5

–4.5

–260

–4

–56

–8.5

–6.5

–325

µA

TMR Pin Pull-down Current VTMR = 1V, VFB = 1V, ΔVSNS = 0V l1.5 2.2 2.7 µA

VTMR TMR Pin Thresholds FLT From High to Low, VCC = 5V to 80V l1.22 1.25 1.28 V

LEAD BASED FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE

LT4356CMS-3 LT4356CMS-3#TR LTFFK 10-Lead Plastic MSOP 0°C to 70°C

LT4356IMS-3 LT4356IMS-3#TR LTFFK 10-Lead Plastic MSOP –40°C to 85°C

LT4356HMS-3 LT4356HMS-3#TR LTFFK 10-Lead Plastic MSOP –40°C to 125°C

LT4356MPMS-3 LT4356MPMS-3#TR LTGGZ 10-Lead Plastic MSOP –55°C to 125°C

LT4356CS-3 LT4356CS-3#TR LT4356S-3 16-Lead Plastic SO 0°C to 70°C

LT4356IS-3 LT4356IS-3#TR LT4356S-3 16-Lead Plastic SO –40°C to 85°C

LT4356HS-3 LT4356HS-3#TR LT4356S-3 16-Lead Plastic SO –40°C to 125°C

LT4356MPS-3 LT4356MPS-3#TR LT4356MPS-3 16-Lead Plastic SO –55°C to 125°C

Consult LTC Marketing for parts speciﬁed with wider operating temperature ranges. *The temperature grade is identiﬁed by a label on the shipping container.

For more information on lead free part marking, go to: http://www.linear.com/leadfree/

For more information on tape and reel speciﬁcations, go to: http://www.linear.com/tapeandreel/

ORDER INFORMATION

LT4356-3

43563fb

The l denotes the speciﬁcations which apply over the full operating

temperature range, otherwise speciﬁcations are at TA = 25°C. VCC = 12V unless otherwise noted.

Note 1: Stresses beyond those listed under Absolute Maximum Ratings

may cause permanent damage to the device. Exposure to any Absolute

Maximum Rating condition for extended periods may affect device

reliability and lifetime.

Note 2: All currents into device pins are positive; all currents out of device

pins are negative. All voltages are referenced to GND unless otherwise

speciﬁed.

Note 3: An internal clamp limits the GATE pin to a minimum of 10V above

the OUT pin. Driving this pin to voltages beyond the clamp may damage

the device.

ELECTRICAL CHARACTERISTICS

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS

ΔVTMR Early Warning Period From F LT going Low to GATE going Low, VCC = 5V to 80V l80 100 120 mV

VIN+IN+ Pin Threshold l1.22 1.25 1.28 V

IIN+IN+ Pin Input Current VIN+ = 1.25V l0.3 1 µA

VOL F LT , EN, AOUT Pins Output Low ISINK = 2mA

ISINK = 0.1mA

300

800

IOUT OUT Pin Input Current VOUT = VCC = 12V; LT4356C, LT4356I, LT4356H

VOUT = VCC = 12V; LT4356MP

VOUT = VCC = 12V, VSHDN = 0V

200

300

310

µA

ΔVOUT OUT Pin High Threshold ΔVOUT = VCC – VOUT; EN From Low to High l0.25 0.5 0.7 V

VSHDN SHDN Pin Threshold VCC = 12V to 48V

0.6

0.4

1.4 1.7

2.1

VSHDN(FLT) SHDN Pin Float Voltage VCC = 12V to 48V l0.6 1.2 2.1 V

ISHDN SHDN Pin Current VSHDN = 0V l–1 –4 –8 µA

tOFF(OC) Overcurrent Turn Off Delay Time GATE From High to Low, ΔVSNS = 0 → 120mV; LT4356C,

LT4356I, LT4356H

LT4356MP

4.5

µs

tOFF(OV) Overvoltage Turn Off Delay Time GATE From High to Low, VFB = 0 → 1.5V l0.25 1 µs

TYPICAL PERFORMANCE CHARACTERISTICS

ICC (Shutdown) vs VCC

ICC vs VCC

ICC (Shutdown) vs Temperature

VCC (V)

ICC (µA)

20 40 60 80

43563 G01

10 30 50 70

VCC (V)

ICC (µA)

200

400

600

20 40 60 80

43563 G02

800

1000

10 30 50 70

TEMPERATURE (°C)

–50

ICC (µA)

0 50 100 125

43563 G03

–25 25 75

Speciﬁcations are at VCC = 12V, TA = 25°C unless otherwise noted.

LT4356-3

43563fb

SHDN Current vs Temperature

GATE Pull-Up Current vs VCC

GATE Pull-Up Current vs

Temperature

GATE Pull-Down Current vs

Temperature

GATE Pull-Down Current vs

Temperature

ΔVGATE vs IGATE

TEMPERATURE (°C)

–50

ISHDN (µA)

0 50 100 125

43563 G04

–25 25 75

VSHDN = 0V

VCC (V)

IGATE (µA)

20 40 60 80

43563 G05

10 30 50 70

TEMPERATURE (°C)

–50

IGATE (µA)

0 50 100 125

43563 G06

–25 25 75

VGATE = VOUT = 12V

TEMPERATURE (°C)

–50

100

IGATE(DOWN) (mA)

120

140

160

0 50 100 125

43563 G07

180

220

200

–25 25 75

OVERVOLTAGE CONDITION

VFB = 1.5V

TEMPERATURE (°C)

–50

IGATE(DOWN) (mA)

0 50 100 125

43563 G08

–25 25 75

OVERCURRENT CONDITION

∆VSNS = 120mV

IGATE (µA)

∆VGATE (V)

4 8 12 16

43563 G09

2 6 10 14

VOUT = 12V

TYPICAL PERFORMANCE CHARACTERISTICS

Speciﬁcations are at VCC = 12V, TA = 25°C unless otherwise noted.

ΔVGATE vs Temperature

ΔVGATE vs VCC

Overvoltage TMR Current vs

(VCC – VOUT)

TEMPERATURE (°C)

–50 0 50 100 125

–25 25 75

∆VGATE (V)

43563 G10

14 IGATE = –1µA

VCC = 8V

VCC = 4V

VCC (V)

0 20 40 60 80

43563 G11

10 30 50 70

∆VGATE (V)

IGATE = –1µA

VOUT = VCC

TA = –45°C

TA = 25°C

TA = 130°C

VCC – VOUT (V)

ITMR (µA)

20 40 60 80

43563 G12

10 30 50 70

OVERVOLTAGE CONDITION

VOUT = 5V

VTMR = 1V

LT4356-3

43563fb

Output Low Voltage vs Current

Overvoltage Turn-Off Time vs

Temperature

Overcurrent Turn-Off Time vs

Temperature

CURRENT (mA)

VOL (V)

1.0

2.0

3.0

0.5

1.5

2.5

3.5

2.0 3.0

43563 G16

4.0

1.00.5 2.51.5

AOUT

FLT

TEMPERATURE (°C)

–50

100

tOFF (ns)

0 50 100 125

43563 G17

500

400

300

200

–25 25 75

OVERVOLTAGE CONDITION

VFB = 1.5V

TEMPERATURE (°C)

–50

1.0

1.5

tOFF (µs)

0 50 100 125

43563 G18

4.0

3.5

3.0

2.5

2.0

–25 25 75

OVERCURRENT CONDITION

∆VSNS = 120mV

VCC (V)

ICC (mA)

–10

–15

–80

43563 G19

–5

0–20 –40 –60

–20 VCC = SNS

Reverse Current vs Reverse

Voltage

Overcurrent TMR Current vs

(VCC – VOUT)

Warning Period

TMR Current vs VCC

TMR Pull-Down Current vs

Temperature

VCC – VOUT (V)

ITMR (µA)

120

160

20 40 60 80

43563 G13

200

280

240

10 30 50 70

OVERCURRENT CONDITION

VOUT = 0V

VTMR = 1V

VCC (V)

0 20 40 60 80

43563 G14

10 30 50 70

ITMR (µA)

14 OVERVOLTAGE, EARLY

WARNING PERIOD

VFB = 1.5V

VTMR = 1.3V

TEMPERATURE (°C)

–50

ITMR (µA)

0 50 100 125

43563 G15

3.0

2.5

2.0

1.5

1.0

0.5

–25 25 75

VTMR = 1V

TYPICAL PERFORMANCE CHARACTERISTICS

Speciﬁcations are at VCC = 12V, TA = 25°C unless otherwise noted.

LT4356-3

43563fb

PIN FUNCTIONS

AOUT (DFN and SO Packages Only): Ampliﬁer Output.

Open collector output of the auxiliary ampliﬁer. It is capable

of sinking up to 2mA from 80V. The negative input of the

ampliﬁer is internally connected to a 1.25V reference.

EN: Open-Collector Enable Output. The EN pin goes high

impedance when the voltage at the OUT pin is above (VCC

– 0.7V), indicating the external MOSFET is fully on. The

state of the pin is latched until the OUT pin voltage resets

at below 0.5V and goes back up above 2V. The internal

NPN is capable of sinking up to 3mA of current from 80V

to drive an LED or opto-coupler.

Exposed Pad: Exposed pad may be left open or connected

to device ground (GND).

FB: Voltage Regulator Feedback Input. Connect this pin

to the center tap of the output resistive divider connected

between the OUT pin and ground. During an overvoltage

condition, the GATE pin is servoed to maintain a 1.25V

threshold at the FB pin. This pin is clamped internally to

7V. Tie to GND to disable the OV clamp.

FLT: Open-Collector Fault Output. This pin pulls low

after the voltage at the TMR pin has reached the fault

threshold of 1.25V. It indicates the pass transistor is

about to turn off because either the supply voltage has

stayed at an elevated level for an extended period of

time (voltage fault) or the device is in an overcurrent

condition (current fault). The internal NPN is capable of

sinking up to 3mA of current from 80V to drive an LED or

opto-coupler.

GATE: N-Channel MOSFET Gate Drive Output. The GATE

pin is pulled up by an internal charge pump current source

and clamped to 14V above the OUT pin. Both voltage and

current ampliﬁers control the GATE pin to regulate the

output voltage and limit the current through the MOSFET.

GND: Device Ground.

IN+ (DFN and SO Packages Only): Positive Input of the

Auxiliary Ampliﬁer. This ampliﬁer can be used as a level

detection comparator with external hysteresis or linear

regulator controlling an external PNP transistor. This pin

is clamped internally to 7V. Connect to ground if unused.

OUT: Output Voltage Sense Input. This pin senses the

voltage at the source of the N-channel MOSFET and sets

the fault timer current. When the OUT pin voltage reaches

0.7V away from VCC, the EN pin goes high impedance.

SHDN: Shutdown Control Input. The LT4356-3 can be shut

down to a low current mode by pulling the SHDN pin below

the shutdown threshold of 0.4V. All functions, including

the spare ampliﬁer, are turned off. Pull this pin above 1.7V

or disconnect it and allow the internal current source to

turn the part back on. After GATE pin pulls low due to fault

time out, the part can be restarted by pulling the SHDN

pin low for at least 100µs and pulled high with a slew rate

faster than 10V/ms. The leakage current to ground at the

pin should be limited to no more than 1µA if no pull up

device is used to turn the part on. The SHDN pin can be

pulled up to 100V or below GND by 60V without damage.

SNS: Current Sense Input. Connect this pin to the output of

the current sense resistor. The current limit circuit controls

the GATE pin to limit the sense voltage between VCC and

SNS pins to 50mV. At the same time the sense ampliﬁer

also starts a current source to charge up the TMR pin.

This pin can be pulled below GND by up to 60V, though

the voltage difference with the VCC pin must be limited to

less than 30V. Connect to VCC if unused.

TMR: Fault Timer Input. Connect a capacitor between this

pin and ground to set the times for early warning and fault

periods. The current charging up this pin during fault

conditions depends on the voltage difference between the

VCC and OUT pins. When VTMR reaches 1.25V, the F LT pin

pulls low to indicate the detection of a fault condition. If

the condition persists, the pass transistor turns off when

VTMR reaches the threshold of 1.35V. The GATE pin remains

low even after the fault condition has disappeared and the

voltage at the TMR pin has reached 0.5V.

VCC: Positive Supply Voltage Input. The positive supply

input ranges from 4V to 80V for normal operation. It

can also be pulled below ground potential by up to 60V

during a reverse battery condition, without damaging the

part. The supply current is reduced to 7µA with all the

functional blocks off.

LT4356-3

43563fb

BLOCK DIAGRAM

–

+–

–

VCC

SHDN

IN+

AUXILIARY

AMPLIFIER

1.25V

50mV

2µA

1.35V

1.25V –

1.25V

0.5V

SNS

TMR GND

GATE

14V

AOUT

OUT

43563 BD

VCC

ITMR

FLT

–

CHARGE

PUMP

CONTROL

LOGIC

GATEOFF FLT

OUT OVOC

SHDN

–

LT4356-3

43563fb

Some power systems must cope with high voltage surges

of short duration such as those in automobiles. Load

circuitry must be protected from these transients, yet

high availability systems must continue operating during

these events.

The LT4356-3 is an overvoltage protection regulator that

drives an external N-channel MOSFET as the pass transis-

tor. It operates from a wide supply voltage range of 4V to

80V. It can also be pulled below ground potential by up

to 60V without damage. The low power supply require-

ment of 4V allows it to operate even during cold cranking

conditions in automotive applications. The internal charge

pump turns on the N-channel MOSFET to supply current

to the loads with very little power loss. Two MOSFETs can

be connected back to back to replace an inline Schottky

diode for reverse input protection. This improves the ef-

ﬁciency and increases the available supply voltage level

to the load circuitry during cold crank.

Normally, the pass transistor is fully on, powering the

loads with very little voltage drop. When the supply volt-

age surges too high, the voltage ampliﬁer (VA) controls

the gate of the MOSFET and regulates the voltage at the

source pin to a level that is set by the external resistive

divider from the OUT pin to ground and the internal 1.25V

reference. A current source starts charging up the capaci-

tor connected at the TMR pin to ground. If the voltage at

the TMR pin, VTMR, reaches 1.25V, the F LT pin pulls low

to indicate impending turn-off due to the overvoltage

condition. The pass transistor stays on until the TMR

pin reaches 1.35V, at which point the GATE pin pulls low

turning off the MOSFET.

The potential at the TMR pin starts decreasing as soon

as the overvoltage condition disappears, but the GATE

pin remains low even when the voltage at the TMR pin

reaches 0.5V. Pulling the SHDN pin low momentarily will

turn the GATE pin back on.

The fault timer allows the load to continue functioning

during short transient events while protecting the MOSFET

from being damaged by a long period of supply overvolt-

age, such as a load dump in automobiles. The timer period

varies with the voltage across the MOSFET. A higher voltage

corresponds to a shorter fault timer period, ensuring the

MOSFET operates within its safe operating area (SOA).

The LT4356-3 senses an overcurrent condition by monitor-

ing the voltage across an optional sense resistor placed

between the VCC and SNS pins. An active current limit

circuit (IA) controls the GATE pin to limit the sense volt-

age to 50mV. A current is also generated to start charging

up the TMR pin. This current is about 5 times the current

generated during an overvoltage event. The FLT pin pulls

low when the voltage at the TMR pin reaches 1.25V and

the MOSFET is turned off when it reaches 1.35V.

An auxiliary ampliﬁer is provided with the negative input

connected to an internal 1.25V reference. The output pull

down device is capable of sinking up to 2mA of current

allowing it to drive an LED or opto coupler. This ampliﬁer

can be conﬁgured as a linear regulator controller driving

an external PNP transistor or a comparator function to

monitor voltages.

The SHDN pin turns off the pass transistor and reduces

the supply current to less than 7µA.

OPERATION

LT4356-3

43563fb

The LT4356-3 can limit the voltage and current to the load

circuitry during supply transients or overcurrent events.

The total fault timer period should be set to ride through

short overvoltage transients while not causing damage

to the pass transistor. The selection of this N-channel

MOSFET pass transistor is critical for this application.

It must stay on and provide a low impedance path from

the input supply to the load during normal operation and

then dissipate power during overvoltage or overcurrent

conditions.

The following sections describe the overcurrent and the

overvoltage faults, and the selection of the timer capacitor

value based on the required warning time. The selection

of the N-channel MOSFET pass transistor is discussed

next. Auxiliary ampliﬁer, reverse input, and the shutdown

functions are covered after the MOSFET selection. External

component selection is discussed in detail in the Design

Example section.

Overvoltage Fault

The LT4356-3 limits the voltage at the OUT pin during an

overvoltage situation. An internal voltage ampliﬁer regu-

lates the GATE pin voltage to maintain a 1.25V threshold at

the FB pin. During this period of time, the power MOSFET

is still on and continues to supply current to the load. This

allows uninterrupted operation during short overvoltage

transient events.

When the voltage regulation loop is engaged for longer

than the time-out period, set by the timer capacitor con-

nected from the TMR pin to ground, an overvoltage fault

is detected. The GATE pin is pulled down to the OUT pin by

a 150mA current. This prevents the power MOSFET from

being damaged during a long period of overvoltage, such

as during load dump in automobiles. Pulling the SHDN

pin low for at least 100µs and pulled high with a slew rate

faster than 10V/ms will allow the GATE pin to pull back up.

Overcurrent Fault

The LT4356-3 features an adjustable current limit that

protects against short circuits or excessive load current.

During an overcurrent event, the GATE pin is regulated to

limit the current sense voltage across the VCC and SNS

pins to 50mV.

An overcurrent fault occurs when the current limit circuitry

has been engaged for longer than the time-out delay set

by the timer capacitor. The GATE pin is then immediately

pulled low by a 10mA current to GND turning off the

MOSFET. The GATE pin stays low until the SHDN pin is

pulled low for at least 100µs and pulled high with a slew

rate faster than 10V/ms.

Fault Timer

The LT4356-3 includes an adjustable fault timer pin. Con-

necting a capacitor from the TMR pin to ground sets the

delay timer period before the MOSFET is turned off. The

same capacitor also sets the cool down period before the

MOSFET is allowed to turn back on after the fault condition

has disappeared.

Once a fault condition, either overvoltage or overcurrent,

is detected, a current source charges up the TMR pin. The

current level varies depending on the voltage drop across

the drain and source terminals of the power MOSFET(VDS),

which is typically from the VCC pin to the OUT pin. This

scheme takes better advantage of the available Safe Oper-

ating Area (SOA) of the MOSFET than would a ﬁxed timer

current. The timer function operates down to VCC = 5V

across the whole temperature range.

APPLICATIONS INFORMATION

LT4356-3

43563fb

Fault Timer Current

The timer current starts at around 2µA with 0.5V or less

of VDS, increasing linearly to 50µA with 75V of VDS dur-

ing an overvoltage fault (Figure 1). During an overcurrent

fault, it starts at 4µA with 0.5V or less of VDS but increases

to 260µA with 80V across the MOSFET (Figure 2). This

arrangement allows the pass transistor to turn off faster

during an overcurrent event, since more power is dissipated

during this condition. Refer to the Typical Performance

Characteristics section for the timer current at different

VDS in both overvoltage and overcurrent events.

When the voltage at the TMR pin, VTMR, reaches the 1.25V

threshold, the F LT pin pulls low to indicate the detection

of a fault condition and provide warning to the load of

the impending power loss. In the case of an overvoltage

fault, the timer current then switches to a ﬁxed 5µA. The

interval between FLT asserting low and the MOSFET turn-

ing off is given by:

tWARNING = CTMR • 100mV

5µA

APPLICATIONS INFORMATION

Figure 1. Overvoltage Fault Timer Current

Figure 2. Overcurrent Fault Timer Current

tFLT

= 15ms/µF

TOTAL FAULT TIMER = tFLT + tWARNING

tWARNING

= 20ms/µF

tFLT = 93.75ms/µF tWARNING

= 20ms/µF

VTMR(V)

ITMR = 5µA ITMR = 5µA

VDS = 75V

(ITMR = 50µA)

VDS = 10V

(ITMR = 8µA)

1.35

1.25

TIME

43563 F01

0.50

tFLT

= 2.88ms/µF

TOTAL FAULT TIMER = tFLT + tWARNING

tFLT = 21.43ms/µF tWARNING

= 2.86ms/µF

tWARNING

= 0.38ms/µF

VTMR(V)

VDS = 10V

(ITMR = 35µA)

1.35

1.25

0.50 TIME

43563 F02

VDS = 80V

(ITMR = 260µA)

LT4356-3

43563fb

The SOA of the MOSFET must encompass all fault condi-

tions. In normal operation the pass transistor is fully on,

dissipating very little power. But during either overvoltage

or overcurrent faults, the GATE pin is servoed to regu-

late either the output voltage or the current through the

MOSFET. Large current and high voltage drop across the

MOSFET can coexist in these cases. The SOA curves of

the MOSFET must be considered carefully along with the

selection of the fault timer capacitor.

Transient Stress in the MOSFET

During an overvoltage event, the LT4356-3 drives a series

pass MOSFET to regulate the output voltage at an acceptable

level. The load circuitry may continue operating throughout

this interval, but only at the expense of dissipation in the

MOSFET pass device. MOSFET dissipation or stress is a

function of the input voltage waveform, regulation voltage

and load current. The MOSFET must be sized to survive

this stress.

Most transient event speciﬁcations use the model shown

in Figure 3. The idealized waveform comprises a linear

ramp of rise time tr, reaching a peak voltage of VPK and

exponentially decaying back to VIN with a time constant

of t. A common automotive transient speciﬁcation has

constants of tr = 10µs, VPK = 80V and t = 1ms. A surge

condition known as “load dump” has constants of tr = 5ms,

VPK = 60V and t = 200ms.

This ﬁxed early warning period allows time for the system

to perform necessary backup or house-keeping functions

before power is cut off. When VTMR crosses the 1.35V

threshold, the GATE pin pulls low immediately and turns

off the MOSFET. Note that during an overcurrent event the

timer current is not reduced to 5µA when VTMR reaches

1.25V, since it would lengthen the overall fault timer period

and cause additional MOSFET stress. After the GATE pin

pulls low due to a fault time out, the LT4356-3 latches off.

Allow sufﬁcient time for the TMR pin to discharge to 0.5V

(typical discharge current is 2.2µA) and for the MOSFET

to cool before attempting to reset the part. To reset, pull

the SHDN pin low for at least 100µs, then pull high with

a slew rate of at least 10V/ms.

MOSFET Selection

The LT4356-3 drives an N-channel MOSFET to conduct the

load current. The important features of the MOSFET are

on-resistance RDS(ON), the maximum drain-source voltage

V(BR)DSS, the threshold voltage, and the SOA.

The maximum allowable drain-source voltage must be

higher than the supply voltage. If the output is shorted

to ground or during an overvoltage event, the full supply

voltage will appear across the MOSFET.

The gate drive for the MOSFET is guaranteed to be more

than 10V and less than 16V for those applications with VCC

higher than 8V. This allows the use of standard threshold

voltage N-channel MOSFETs. For systems with VCC less

than 8V, a logic level MOSFET is required since the gate

drive can be as low as 4.5V.

APPLICATIONS INFORMATION

Figure 3. Prototypical Transient Waveform

VPK

VIN

43563 F03

LT4356-3

43563fb

APPLICATIONS INFORMATION

MOSFET stress is the result of power dissipated within

the device. For long duration surges of 100ms or more,

stress is increasingly dominated by heat transfer; this is

a matter of device packaging and mounting, and heat sink

thermal mass. This is analyzed by simulation, using the

MOSFET thermal model.

For short duration transients of less than 100ms, MOSFET

survival is increasingly a matter of safe operating area

(SOA), an intrinsic property of the MOSFET. SOA quanti-

ﬁes the time required at any given condition of VDS and

ID to raise the junction temperature of the MOSFET to its

rated maximum. MOSFET SOA is expressed in units of

watt-squared-seconds (P2t). This ﬁgure is essentially con-

stant for intervals of less than 100ms for any given device

type, and rises to inﬁnity under DC operating conditions.

Destruction mechanisms other than bulk die temperature

distort the lines of an accurately drawn SOA graph so that

P2t is not the same for all combinations of ID and VDS.

In particular P2t tends to degrade as VDS approaches the

maximum rating, rendering some devices useless for

absorbing energy above a certain voltage.

Calculating Transient Stress

To select a MOSFET suitable for any given application, the

SOA stress must be calculated for each input transient

which shall not interrupt operation. It is then a simple matter

to chose a device which has adequate SOA to survive the

maximum calculated stress. P2t for a prototypical transient

waveform is calculated as follows (Figure 4).

Let

a = VREG – VIN

b = VPK – VIN

(VIN = Nominal Input Voltage)

Then

P2t=ILOAD21

3tr

(b a)3

22a2ln b

a+3a2+b24ab

Typically VREG ≈ VIN and t >> t r simplifying the above to

P2t=1

ILOAD2(VPK – VREG)2τ(W2s)

For the transient conditions of VPK = 80V, VIN = 12V, VREG

= 16V, tr = 10µs and t = 1ms, and a load current of 3A,

P2t is 18.4W2s—easily handled by a MOSFET in a D-pak

package. The P2t of other transient waveshapes is evaluated

by integrating the square of MOSFET power versus time.

Calculating Short-Circuit Stress

SOA stress must also be calculated for short-circuit condi-

tions. Short-circuit P2t is given by:

P2t = (VIN • ΔVSNS/RSNS)2 • tTMR (W2s)

where, ΔVSNS is the SENSE pin threshold, and tTMR is the

overcurrent timer interval.

For VIN = 14.7V, VSNS = 50mV, RSNS = 12mΩ and CTMR

= 100nF, P2t is 6.6W2s—less than the transient SOA

calculated in the previous example. Nevertheless, to

account for circuit tolerances this ﬁgure should be doubled

to 13.2W2s.

Limiting Inrush Current and GATE Pin Compensation

The LT4356-3 limits the inrush current to any load capaci-

tance by controlling the GATE pin voltage slew rate. An

external capacitor can be connected from GATE to ground

to slow down the inrush current further at the expense of

slower turn-off time. The gate capacitor is set at:

C1 = IGATE(UP)

IINRUSH

•CL

Figure 4. Safe Operating Area Required to Survive Prototypical

Transient Waveform

VPK

VIN

43563 F04

VREG

LT4356-3

43563fb

Figure 5

Figure 6. Auxiliary LDO Output with Optional Current Limit

43563 F05

LT4356-3

GATE

IN4148W

*4.7Ω

D1*

BAV99

2N2905A OR

BCP53

249k 47nF

INPUT 2.5V OUTPUT

≈ 150mA MAX

* OPTIONAL FOR

CURRENT LIMIT

LT4356DE-3

AOUT

RLIM

100k

249k

43563 F06

IN+

10µF

R4 + R5

VOUT = 1.25

ILIM ≈ 0.7

RLIM

APPLICATIONS INFORMATION

The LT4356-3 does not need extra compensation compo-

nents at the GATE pin for stability during an overvoltage

or overcurrent event. However, with fast, high voltage

transient steps at the input, a gate capacitor, C1, to ground

is needed to prevent turn-on of the N-channel MOSFET.

The extra gate capacitance slows down the turn off time

during fault conditions and may allow excessive current

during an output short event. An extra resistor, R1, in series

with the gate capacitor can improve the turn off time. A

diode, D1, should be placed across R1 with the cathode

connected to C1 as shown in Figure 5.

Reverse Input Protection

A blocking diode is commonly employed when reverse

input potential is possible, such as in automotive applica-

tions. This diode causes extra power loss, generates heat,

and reduces the available supply voltage range. During

cold crank, the extra voltage drop across the diode is

particularly undesirable.

The LT4356-3 is designed to withstand reverse voltage

without damage to itself or the load. The VCC, SNS, and

SHDN pins can withstand up to 60V of DC voltage below

the GND potential. Back-to-back MOSFETs must be used

to eliminate the current path through their body diodes

(Figure 7). Figure 8 shows the approach with a P-Channel

MOSFET in place of Q2.

Figure 7. Overvoltage Regulator with N-channel MOSFET

Reverse Input Protection

CTMR

0.1µF

RSNS

10mΩ

IRLR2908

VIN

12V

VOUT

12V, 3A

CLAMPED

AT 16V

43563 F07

LT4356DE-3

GND TMR

10 1

OUTSNS

SHDN

AOUT

IN+

VCC

FLT

D2*

SMAJ58CA

4.99k

59k

GATE

10k

2N3904

1N4148

10Ω

*DIODES INC.

Auxiliary Ampliﬁer

An uncommitted ampliﬁer is included in the LT4356-3 to

provide ﬂexibility in the system design. With the negative

input connected internally to the 1.25V reference, the

ampliﬁer can be connected as a level detect comparator

with external hysteresis. The open collector output pin,

AOUT, is capable of driving an opto or LED. It can also

interface with the system via a pull-up resistor to a supply

voltage up to 80V.

The ampliﬁer can also be conﬁgured as a low dropout

linear regulator controller. With an external PNP transistor,

such as 2N2905A, it can supply up to 100mA of current

with only a few hundred mV of dropout voltage. Current

limit can be easily included by adding two diodes and one

resistor (Figure 6). The ampliﬁer is turned off when the

LT4356-3 is shut down.

LT4356-3

43563fb

APPLICATIONS INFORMATION

Shutdown

The LT4356-3 can be shut down to a low current mode

when the voltage at the SHDN pin goes below the shutdown

threshold of 0.6V. The quiescent current drops to 7µA. All

functions are turned off including the auxiliary ampliﬁer.

After the GATE pin pulls low due to a fault time out, the

LT4356-3 latches off. Allow sufﬁcient time for the TMR pin

to discharge to 0.5V (typical discharge current is 2.2µA)

and for the MOSFET to cool before attempting to reset the

part. To reset, pull the SHDN pin low for at least 100µs,

then pull high with a slew rate of at least 10V/ms.

The SHDN pin can be pulled up to VCC or below GND by

up to 60V without damaging the pin. Leaving the pin open

allows an internal current source to pull it up and turn

on the part while clamping the pin to 2.5V. The leakage

current at the pin should be limited to no more than 1µA

if no pull up device is used to help turn it on.

Supply Transient Protection

The LT4356-3 is 100% tested and guaranteed to be safe

from damage with supply voltages up to 80V. Nevertheless,

voltage transients above 100V may cause permanent dam-

age. During a short-circuit condition, the large change in

current ﬂowing through power supply traces and associated

wiring can cause inductive voltage transients which could

exceed 100V. To minimize the voltage transients, the power

trace parasitic inductance should be minimized by using

wide traces. A small surge suppressor, D2, in Figure 9,

at the input will clamp the voltage spikes.

A total bulk capacitance of at least 22µF low ESR is required

close to the source pin of MOSFET Q1. In addition, the

bulk capacitance should be at least 10 times larger than

the total ceramic bypassing capacitor on the input of the

DC/DC converter.

Layout Considerations

To achieve accurate current sensing, Kelvin connection

to the current sense resistor (RSNS in Figure 9) is recom-

mended. The minimum trace width for 1oz copper foil is

0.02" per amp to ensure the trace stays at a reasonable

temperature. 0.03" per amp or wider is recommended.

Note that 1oz copper exhibits a sheet resistance of about

530µΩ/square. Small resistances can cause large errors in

high current applications. Noise immunity will be improved

signiﬁcantly by locating resistive dividers close to the pins

with short VCC and GND traces.

Design Example

As a design example, take an application with the following

speciﬁcations: VCC = 8V to 14V DC with transient up to 80V,

VOUT ≤ 16V, current limit (ILIM) at 5A, low battery detection

at 6V, and 1ms of overvoltage early warning (Figure 9).

Figure 8. Overvoltage Regulator with P-Channel MOSFET

Reverse Input Protection

CTMR

0.1µF

RSNS

10mΩ

IRLR2908

Si4435

VIN

12V

VOUT

12V, 3A

CLAMPED AT 16V

43563 F08

LT4356DE-3

GND TMR

10 1

OUTSNS

SHDN

AOUT

IN+

VCC

FLT

4.99k

59k

GATE

10k

1N5245

15V

10Ω

D2*

SMAJ58CA

*DIODES INC.

Figure 9. Overvoltage Regulator with Low-Battery Detection

CTMR

47nF

*SANYO 25CE22GA

10Ω

RSNS

10mΩ Q1

IRLR2908

SMAJ58A

VIN

43563 F09

LT4356DE-3

GND TMR

OUTGATESNS

IN+

SHDN

AOUT FAULT

FLTUNDERVOLTAGE

CL*

22µF

DC-DC

CONVERTER

GND

SHDN

VCC

4.99k

383k

100k

59k

10 1

345

VCC

LT4356-3

43563fb

First, calculate the resistive divider value to limit VOUT to

16V during an overvoltage event:

VREG =1.25V • R1 + R2

( )

=16V

Set the current through R1 and R2 during the overvoltage

condition to 250µA.

R2 = 1.25V

250µA = 5kΩ

Choose 4.99kΩ for R2.

R1 = 16V – 1.25V

( )

• R2

1.25V = 58.88kΩ

The closest standard value for R1 is 59kΩ.

Next calculate the sense resistor, RSNS, value:

RSNS = 50mV

ILIM

= 50mV

5A = 10mΩ

CTMR is then chosen for 1ms of early warning time:

CTMR = 1ms • 5µA

100mV = 50nF

The closest standard value for CTMR is 47nF.

Finally, calculate R4 and R5 for the 6V low battery thresh-

old detection:

6V = 1.25V • R4 + R5

( )

Choose 100kΩ for R5.

R4 = 6V – 1.25V

( )

• R5

1.25V = 380kΩ

Select 383kΩ for R4.

The pass transistor, Q1, should be chosen to withstand

the output short condition with VCC = 14V.

The total overcurrent fault time is:

tOC = 47nF • 0.85V

45.5µA = 0.878ms

The power dissipation on Q1 equals to:

P = 14V • 50mV

10m

Ω

= 70W

These conditions are well within the Safe Operating Area

of IRLR2908.

APPLICATIONS INFORMATION

LT4356-3

43563fb

TYPICAL APPLICATIONS

24V Overvoltage Regulator Withstands 150V at VIN

CTMR

0.1µF

IRF640

VIN

24V

VOUT

CLAMPED AT 32V

43563 TA05

LT4356DE-3

GND TMR

10 1

OUTSNS

SHDN

FLT

VCC

6FB 2

D2*

SMAT70A

4.99k

118k

GATE

10Ω

*DIODES INC.

Wide Input Range 5V to 28V Hot Swap with Undervoltage Lockout

CTMR

1µF

10Ω

SNS

0.02Ω

SUD50N03-10

VIN

43563 TA10

LT4356DE-3

GND TMR

OUTGATESNS

IN+

SHDN

AOUT

VOUT

FLT

VCC

49.9k

118k

100µF

47nF

LT4356-3

43563fb

Overvoltage Regulator with Low Battery Detection and Output Keep Alive During Shutdown

TYPICAL APPLICATIONS

10Ω

RSNS

10mΩ

VIN

12V

VOUT

12V, 4A

CLAMPED AT 16V

43563 TA03

LT4356DE-3

GND TMR

10 1

OUTGATESNS

345

IN+

SHDN

VCC

VDD

THRESHOLD = 6V

FLT

AOUT LBO

1N4746A

18V

24.9k

47k

402k

105k

294k

0.5W

IRLR2908

VN2222

CTMR

0.1µF

D2*

SMAJ58A

*DIODES INC.

2.5A, 48V Hot Swap with Overvoltage Output Regulation at 72V and UV Shutdown at 35V

1N4714

BV = 33V

6.8nF

CTMR

0.1µF

10Ω

SNS

15mΩ VOUT

48V

2.5A

43563 TA06

LT4356DE-3

GND TMR

10 1

OUTGATESNSVCC

3456

SHDN

FLT

AOUT PWRGD

IN+

300µF

4.02k

140k

100k

47k

4.02k

226k

FDB3632

D2*

SMAT70A

VIN

48V

*DIODES INC.

LT4356-3

43563fb

2.5A, 28V Hot Swap with Overvoltage Output Regulation at 36V and UV Shutdown at 15V

TYPICAL APPLICATIONS

1N4700

BV = 13V

6.8nF

CTMR

0.1µF

10Ω

SNS

15mΩ VOUT

28V

2.5A

43563 TA07

LT4356DE-3

GND TMR

10 1

OUTGATESNSVCC

3456

SHDN

FLT

AOUT PWRGD

IN+

300µF

4.02k

113k

27k

47k

4.02k

110k

FDB3632

D2*

SMAT70A

*DIODES INC.

VIN

28V

Overvoltage Regulator with Reverse Input Protection Up to –80V

CTMR

0.1µF

RSNS

10mΩ

IRLR2908

VIN

12V

VOUT

12V, 3A

CLAMPED

AT 16V

43563 TA09

LT4356DE-3

GND TMR

10 1

OUTSNSVCC

SHDN

AOUT

IN+

FLT

D2*

SMAJ58CA

4.99k

59k

GATE

10k

2N3904

1N4148

D3**

1N4148

**OPTIONAL COMPONENT

FOR REDUCED STANDBY CURRENT

10Ω

*DIODES INC.

LT4356-3

43563fb

DE/UE Package

12-Lead Plastic DFN (4mm × 3mm)

(Reference LTC DWG # 05-08-1695 Rev D)

4.00 ±0.10

(2 SIDES)

3.00 ±0.10

(2 SIDES)

NOTE:

1. DRAWING PROPOSED TO BE A VARIATION OF VERSION

(WGED) IN JEDEC PACKAGE OUTLINE M0-229

2. DRAWING NOT TO SCALE

3. ALL DIMENSIONS ARE IN MILLIMETERS

4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE

MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE

5. EXPOSED PAD SHALL BE SOLDER PLATED

6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION

ON THE TOP AND BOTTOM OF PACKAGE

0.40 ± 0.10

BOTTOM VIEW—EXPOSED PAD

1.70 ± 0.10

0.75 ±0.05

R = 0.115

TYP

R = 0.05

TYP

2.50 REF

127

PIN 1 NOTCH

R = 0.20 OR

0.35 × 45°

CHAMFER

PIN 1

TOP MARK

(NOTE 6)

0.200 REF

0.00 – 0.05

(UE12/DE12) DFN 0806 REV D

2.50 REF

RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS

APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED

2.20 ±0.05

0.70 ±0.05

3.60 ±0.05

PACKAGE OUTLINE

3.30 ±0.10

0.25 ± 0.05

0.50 BSC

1.70 ± 0.05

3.30 ±0.05

0.50 BSC

0.25 ± 0.05

PACKAGE DESCRIPTION

Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.

LT4356-3

43563fb

MS Package

10-Lead Plastic MSOP

(Reference LTC DWG # 05-08-1661)

MSOP (MS) 0307 REV E

0.53 ± 0.152

(.021 ± .006)

SEATING

PLANE

0.18

(.007)

1.10

(.043)

MAX

0.17 –0.27

(.007 – .011)

TYP

0.86

(.034)

REF

0.50

(.0197)

BSC

1234 5

4.90 ± 0.152

(.193 ± .006)

0.497 ± 0.076

(.0196 ± .003)

REF

8910 76

3.00 ± 0.102

(.118 ± .004)

(NOTE 3)

3.00 ± 0.102

(.118 ± .004)

(NOTE 4)

NOTE:

1. DIMENSIONS IN MILLIMETER/(INCH)

2. DRAWING NOT TO SCALE

3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.

MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE

4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.

INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE

5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX

0.254

(.010) 0° – 6° TYP

DETAIL “A”

GAUGE PLANE

5.23

(.206)

MIN

3.20 – 3.45

(.126 – .136)

0.889 ± 0.127

(.035 ± .005)

RECOMMENDED SOLDER PAD LAYOUT

0.305 ± 0.038

(.0120 ± .0015)

TYP

0.50

(.0197)

BSC

0.1016 ± 0.0508

(.004 ± .002)

PACKAGE DESCRIPTION

Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.

LT4356-3

43563fb

PACKAGE DESCRIPTION

Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.

.016 – .050

(0.406 – 1.270)

.010 – .020

(0.254 – 0.508)× 45°

0° – 8° TYP

.008 – .010

(0.203 – 0.254)

2345678

N/2

.150 – .157

(3.810 – 3.988)

NOTE 3

16 15 14 13

.386 – .394

(9.804 – 10.008)

NOTE 3

.228 – .244

(5.791 – 6.197)

12 11 10 9

S16 REV G 0212

.053 – .069

(1.346 – 1.752)

.014 – .019

(0.355 – 0.483)

TYP

.004 – .010

(0.101 – 0.254)

.050

(1.270)

BSC

.245

MIN

1 2 3 N/2

.160 ±.005

RECOMMENDED SOLDER PAD LAYOUT

.045 ±.005

.050 BSC

.030 ±.005

TYP

INCHES

(MILLIMETERS)

NOTE:

1. DIMENSIONS IN

2. DRAWING NOT TO SCALE

3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.

MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)

4. PIN 1 CAN BE BEVEL EDGE OR A DIMPLE

S Package

16-Lead Plastic Small Outline (Narrow .150 Inch)

(Reference LTC DWG # 05-08-1610 Rev G)

LT4356-3

43563fb

Information furnished by Linear Technology Corporation is believed to be accurate and reliable.

However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-

tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.

REVISION HISTORY

REV DATE DESCRIPTION PAGE NUMBER

A 12/09 Revise Features and Description

Update Absolute Maximum Ratings, Pin Conﬁguration, Order Information and Electrical Characteristics to Include

H-grade

Revise Pin Functions

Revise Block Diagram

Minor Text Edits to Operation Section

Text Added to Applications Information

Update Typical Applications

2-4

12, 15

18, 19

B 8/12 Added MP-Grade 2, 3, 4

LT4356-3

43563fb

Linear Technology Corporation

1630 McCarthy Blvd., Milpitas, CA 95035-7417

(408) 432-1900 l FAX: (408) 434-0507 l www.linear.com

 LINEAR TECHNOLOGY CORPORATION 2009

LT 0812 REV B • PRINTED IN USA

TYPICAL APPLICATION

PART NUMBER DESCRIPTION COMMENTS

LT1641-1/LT1641-2 Positive High Voltage Hot Swap™ Controllers Active Current Limiting, Supplies From 9V to 80V

LTC1696 Overvoltage Protection Controller ThinSOT™ Package, 2.7V to 28V

LTC1735 High Efﬁciency Synchronous Step-Down

Switching Regulator

Output Fault Protection, 16-Pin SSOP

LTC1778 No RSENSE™ Wide Input Range Synchronous

Step-Down Controller

Up to 97% Efﬁciency, 4V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ (0.9)(VIN),

IOUT Up to 20A

LTC2909 Triple/Dual Inputs UV/OV Negative Monitor Pin Selectable Input Polarity Allows Negative and OV Monitoring

LTC2912/LTC2913 Single/Dual UV/OV Voltage Monitor Ads UV and OV Trip Values, ±1.5% Threshold Accuracy

LTC2914 Quad UV/OV Monitor For Positive and Negative Supplies

LTC3727/LTC3727-1 2-Phase, Dual, Synchronous Controller 4V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 14V

LTC3827/LTC3827-1 Low IQ, Dual, Synchronous Controller 4V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 10V, 80µA Quiescent Current

LTC3835/LTC3835-1 Low IQ, Synchronous Step-Down Controller Single Channel LTC3827/LTC3827-1

LT3845 Low IQ, Synchronous Step-Down Controller 4V ≤ VIN ≤ 60V, 1.23V ≤ VOUT ≤ 36V, 120µA Quiescent Current

LT3850 Dual, 550kHz, 2-Phase Synchronous Step-Down

Controller

Dual 180° Phased Controllers, VIN 4V to 24V, 97% Duty Cycle, 4mm × 4mm

QFN-28, SSOP-28 Packages

LT4256 Positive 48V Hot Swap Controller with

Open-Circuit Detect

Foldback Current Limiting, Open-Circuit and Overcurrent Fault Output, Up to

80V Supply

LTC4260 Positive High Voltage Hot Swap Controller with

ADC and I2C

Wide Operating Range 8.5V to 80V

LTC4352 Ideal MOSFET ORing Diode External N-channel MOSFETs Replace ORing Diodes, 0V to 18V

LTC4354 Negative Voltage Diode-OR Controller Controls Two N-channel MOSFETs, 1µs Turn-Off, 80V Operation

LTC4355 Positive Voltage Diode-OR Controller Controls Two N-channel MOSFETs, 0.5µs Turn-Off, 80V Operation

Overvoltage Regulator with Linear Regulator Up to 100mA

CTMR

0.1µF

10Ω

RSNS

10mΩ

2N2905A

VIN

12V

VOUT

12V, 3A

CLAMPED AT 16V

2.5V, 100mA

43563 TA04

LT4356DE-3

GND TMR

10 1

OUTGATESNS

345

AOUT

SHDN

VCC

FLT

IN+12

10µF

4.99k

100k

59k

249k

47nF

IRLR2908

D2*

SMAJ58A

*DIODES INC.

RELATED PARTS