The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. NEW High-Speed (3.125Gbps) Stacking Connectors FX8C Series Mechanical features 0.6mm Pitch Stacking Height : 5~16mm Number of Contacts : 60, 80, 100, 120, 140, SMT Coplanarity 160, 200, 240, 280 The coplanarity of the SMT solder area lead is maintained at the high accuracy of less than 0.1mm. Mating Guide fig.1 H +0.3 -0.2 2 Effective Mating Length The very small and guide rib is provided, and secures 0.6mm self-alignment, considering the mating operativity into accounts. ( fig.1 ) The boss prevents mis-insertion in the board to cause due to the boss position and boss diameter. Two-piece Connection Product In order to enhance the mating reliability for fine pitch connector using two-pieces, the two-pieces of connectors are combined by our unique method, and can secure the mount position accuracy. In such a new concept, the two-piece connected product is prepared at every number of contacts ( The standard mating pitch for the two-piece interconnected product in two rows is 11mm. ) H:Stacking Height 0.6 0.6 Effective Mating Length : 2mm ( fig.1 ) Mis-insertion Prevention Signal integrity features Insertion-Loss-to-Crosstalk-Ratio ( ICR ) The insertion-loss-to-crosstalk ratio (ICR) with five-aggressor differential FEXT meets the IEEE 802.3ap specification for 3.125+ Gbps with plenty of margins. Differential Impedance The differential impedance is within 10010 ohms at 100 ps rise time (20% to 80%). Receptacle FX8C-**S-SV FX8C-** / **S11-SVJ FX8C-**S-SV5 FX8C-** / **S11-SV5J FX8C-**P-SV FX8C-** / **P11-SVJ 5mm 10mm FX8C-**P-SV1 FX8C-** / **P11-SV1J 6mm 11mm FX8C-**P-SV2 FX8C-**/**P11-SV2J 7mm 12mm FX8C-**P-SV4 FX8C-** / **P11-SV4J 9mm 14mm FX8C-**P-SV6 FX8C-** / **P11-SV6J 11mm 16mm Header 516 Stacking height variations (5mm~16mm) 2010.22 1 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8C SeriesHigh-Speed (3.125Gbps) Stacking Connectors FX8C Series Product Specifications Rating Current rating 0.4A Operating Temperature Range -55c to +85c Note 1. Storage Temperature Range -10c to +60c Note 2. Voltage rating 100V AC Operating Humidity Range -40% to 80% Storage Humidity Range 40% to 70% Item Specification Condition 1. Insulation Resistance 100M ohms min. 250V DC 2. Withstanding voltage No flashover or insulation breakdown. 300V AC/1 minute 3. Contact Resistance 80m ohms max. 100mA 4. Vibration No electrical discontinuity of 1s or more Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 5. Humidity (Steady state) Contact resistance: 100m ohms max.Insulation resistance: 100M ohms min. 96 hours at temperature of 40 2c and humidity of 90% to 95% 6. Temperature Cycle Contact resistance: 100m ohms max.Insulation resistance: 100M ohms min. (-55c: 30 minutes, 15 to 35c: 2 to 3 minutes (-85c: 30 minutes, 15 to 35c: 2 to 3minutes) 5 cycles 7. Durability (Mating/un-mating) Contact resistance: 100m ohms max. 50 cycles 8. Resistance to Soldering heat No deformation of components affecting performance. Reflow: At the recommended temperature profile Manual soldering: 360c for 5 seconds Note 1 : Includes temperature rise caused by current flow. Note 2 : The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation. Note 3 : Slight variations in color of the plastic compounds do not affect form ,fit or function of the connector. Note 4 : FX8C-*P-SV(*),FX8C-*S-SV(*) is gold plated. Note 5 : Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. Material Part Material Finish Remarks Insulator PPS Light brown UL94V-0 Header Contact Phosphor bronze Contact area Lead area Gold plated Tin plated(Note 4) ------- Receptacle Contact Phosphor bronze Contact area Lead area Gold plated Tin plated(Note 4) ------- Ordering Information Single Product - 120 P - SV 1 (91) FX8C q w q Series Name : FX8C e r t y w Number of Contacts :60, 80, 100, 120, 140 t Product height variation Blank : Standard (Minimum low profile) 1: +1mm . . . . . . 6:+6mm e Connector type y Packaging Type P :Header S :Receptacle r Contact type (71) : Tray packaging SV :Board vertical type (91) : Tube packaging (92) : Embossed tape package two-piece Connection Product FX8C - 120/120 P 11 - SV 1 J q w e r t y u q Series Name :FX8C r Connector to Connector Pitch w Number of Contacts: 602, 802, 1002, t Contact type e Connector Type : SV : Board vertical type Example: 120/120 = 240 contacts y Product Height VariationBlank : Standard (Minimum lot profile) 1:+1mm . . . . . . 6:+6mm P : Header u J: two-piece connection product 1202, 1402 S : Receptacle *The standard packaging of the two-piece connection product is the tray packaging. 2 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8C SeriesHigh-Speed (3.125Gbps) Stacking Connectors Signal integrity Pin assignment To match 100 ohm differential impedance and to reduce crosstalk, a staggered GSGSG pin assignment is recommended for FX8C of 5mm to 9mm height, and a staggered GSSG pin assignment is recommended for 10mm to 16mm height. (G=ground and S=signal) GSGSG GSSG signal ground Impedance The differential impedance is 100 10 ohm for FX8C of 5mm and 16mm height at 100 ps rise time (20% to 80%). 5mm 16mm Propagation delay The propagation delay is 69 and 118 ps for FX8C of 5mm and 16mm height, respectively. Insertion loss The differential insertion loss crosses 1 dB at 7 and 5 GHz for FX8C of 5mm and 16mm height, respectively. 5mm 16mm 3 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8C SeriesHigh-Speed (3.125Gbps) Stacking Connectors Return loss The differential return loss meets the IEEE 802.3ap specification to 10 and 7 GHz for FX8C of 5mm and 16mm height, respectively. 5mm 16mm Near-end crosstalk (NEXT) The staggered GSGSG and GSSG pin assignments resulted in low differential NEXT. 5mm 4 16mm The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8C SeriesHigh-Speed (3.125Gbps) Stacking Connectors Far-end crosstalk (FEXT) The staggered GSGSG and GSSG pin assignments resulted in low differential FEXT. 5mm 16mm Insertion-loss-to-crosstalk ratio (ICR) The insertion-loss-to-crosstalk ratio (ICR) with multi-aggressor* differential FEXT meets the extrapolated IEEE 802.3ap specification to 7+ GHz with plenty of margins. 5mm 16mm 5 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8C SeriesHigh-Speed (3.125Gbps) Stacking Connectors A0.3 B 0.05 -0.2 C 0.05 -0.2 D0.2 P=0.60.1 5.10.3 (0.75) 4.450.3 (0.4) 6.5 0 -0.3 Header (Single Product) [FX8C-**P-SV] (C1) Polarity mark (O0.9) t0.20.03w0.250.03 E0.1 (2.4) (O0.6) (1.5) (2.4) Unit:mm Part Number FX8C-060P-SV(92) FX8C-080P-SV(92) FX8C-100P-SV(92) FX8C-120P-SV(92) FX8C-140P-SV(92) CL No. Number of Contacts 60 578-0501-9-92 80 578-0503-4-92 100 578-0505-0-92 120 578-0506-2-92 140 578-0507-5-92 A 24.60 30.60 36.60 42.60 48.60 B 23.00 29.00 35.00 41.00 47.00 C 20.70 26.70 32.70 38.70 44.70 D 17.40 23.40 29.40 35.40 41.40 E Tube packaging Quantity (Pieces) RoHS 22.20 21 28.20 17 34.20 14 YES 40.20 12 46.20 10 **71 : Tray packaging product 91: Tube packaging product 92: Embossed tape packaging product Note 1: To order the tube packaging product, please determine the quantity for delivery, multiplying the tube packaging product by an integer. Note 2: The embossed tape packaging product is prepared for 60 and 80 contacts only. In addition, the product will be procured per reel unit. Please refer to the delivery form item on page 12 for details. Note 3: Tray packaging product is not for board placement with automatic equipment. (0.75) F0.3 (0.4) 6.50 -0.3 [FX8C-**P-SV1] [FX8C-**P-SV2] [FX8C-**P-SV4] [FX8C-**P-SV6] 5.10.3 A0.3 B0.05 -0.2 C0.05 -0.2 D0.2 P=0.60.1 (C1) Polarity mark t0.20.03w0.250.03 E0.1 (2.4) (O0.6) (O0.9) (1.5) (2.4) Unit: mm Note 5 Part Number FX8C-060P-SV1(92) FX8C-060P-SV2(92) FX8C-060P-SV4(92) FX8C-060P-SV6(92) FX8C-080P-SV1(92) FX8C-080P-SV2(92) FX8C-080P-SV4(92) FX8C-080P-SV6(92) FX8C-100P-SV1(92) FX8C-100P-SV2(92) FX8C-100P-SV4(92) FX8C-100P-SV6(92) FX8C-120P-SV1(92) FX8C-120P-SV2(92) FX8C-120P-SV4(92) FX8C-120P-SV6(92) FX8C-140P-SV1(92) FX8C-140P-SV2(92) FX8C-140P-SV4(92) FX8C-140P-SV6(93) CL No. 578-0521-6-92 578-0541-3-92 578-0581-8-92 578-0601-3-92 578-0523-1-92 578-0543-9-92 578-0583-3-92 578-0603-9-92 578-0525-7-92 578-0545-4-92 578-0585-9-92 578-0605-4-92 578-0526-0-92 578-0546-7-92 578-0586-1-92 578-0606-7-92 578-0527-2-92 578-0547-0-92 578-0587-4-92 578-0607-0-93 Number of Contacts A B C D E 60 24.60 23.00 20.70 17.40 22.20 80 30.60 29.00 26.70 23.40 28.20 100 36.60 35.00 32.70 29.40 34.20 120 42.60 41.00 38.70 35.40 40.20 140 48.60 47.00 44.70 41.40 46.20 F Tube packaging Quantity (Pieces) RoHS 5.45 6.45 21 8.45 10.45 5.45 6.45 17 8.45 10.45 5.45 6.45 YES 14 8.45 10.45 5.45 6.45 12 8.45 10.45 5.45 6.45 10 8.45 10.45 ** 71: Tray packaging product 91: Tube packaging product 92: Embossed tape packaging product Note 1: To order the tube packaging product, please determine a quantity for delivery,multiplying the tube packaging product by an integer. Note 2: The embossed tape packaging product is prepared for 60 and 80 contacts only. In addition, the product will be sold per reel unit. Please refer to the packaging specification item on page 12 for details. Note 3: The locator material is installed between leads for the FX8C-P-SV6 type. Note 4: Tray packaging product is not for board placement with automatic equipment. Note 5: (93) spec is with vacuum pick-up tape, embossed tape packaging product. 6 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8C SeriesHigh-Speed (3.125Gbps) Stacking Connectors Receptacle (Single Product) [FX8C-**S-SV] A0.3 B 0.2 -0 C 0.2 -0 D0.2 P=0.60.1 5.60.3 3.950.25 (0.75) 7 0 -0.3 (C1) Polarity mark(Rear side) (1.8) t0.20.03w0.250.03 E0.1 (O0.9) (2.4) (O0.6) (2.4) Unit:mm Part Number CL No. Number of Contacts FX8C-060S-SV(92) 578-0801-2-92 60 24.60 23.05 20.80 17.40 22.20 A B C D E Tube packaging Quantity (Pieces) RoHS 21 FX8C-080S-SV(92) 578-0803-8-92 80 30.60 29.05 26.80 23.40 28.20 17 FX8C-100S-SV(92) 578-0805-3-92 100 36.60 35.05 32.80 29.40 34.20 14 FX8C-120S-SV(92) 578-0806-6-92 120 42.60 41.05 38.80 35.40 40.20 12 FX8C-140S-SV(92) 578-0807-9-92 140 48.60 47.05 44.80 41.40 46.20 10 YES ** 71: Tray packaging product 91: Tube packaging product 92: Embossed tape packaging product Note 1: To order the tube packaging product, please determine a quantity for delivery,multiplying the tube packaging product by an integer. Note 2: The embossed tape packaging product is prepared for 60 and 80 contacts only. In addition, the product will be procured per reel unit. Please refer to the packaging specification item on page 12 for details. Note 3: Tray packaging product is not for board placement with automatic equipment. A0.3 B0.2 -0 C0.2 -0 D0.2 P=0.60.1 [FX8C-**S-SV5] 8.950.25 (0.75) 5.60.3 7 0 -0.3 (C1) Polarity mark(Rear side) (2.4) A B C (1.8) t0.20.03w0.250.03 E0.1 (O0.9) D (O0.6) (2.4) E Unit:mm Part Number CL No. Number of Contacts FX8C-060S-SV5(92) 578-0821-0-92 60 24.60 23.05 20.80 17.40 22.20 Tube packaging Quantity (Pieces) RoHS 21 FX8C-080S-SV5(92) 578-0823-5-92 80 30.60 29.05 26.80 23.40 28.20 17 FX8C-100S-SV5(92) 578-0825-0-92 100 36.60 35.05 32.80 29.40 34.20 14 FX8C-120S-SV5(92) 578-0826-3-92 120 42.60 41.05 38.80 35.40 40.20 12 FX8C-140S-SV5(92) 578-0827-6-92 140 48.60 47.05 44.80 41.40 46.20 10 YES ** 71: Tray packaging product 91: Tube packaging product 92: Embossed tape packaging product Note 1: To order the tube packaging product, please determine a quantity for delivery,multiplying the tube packaging product by an integer. Note 2: The embossed tape package product is prepared for 60 and 80 contacts only. In addition, the product will be procured per reel unit. Please refer to the packaging specification item on page 12 for details. Note 3: Tray packaging product is not for board placement with automatic equipment. BPCB mounting pattern [FX8C-**S-SV,SV5*] 5 0.0 0.0 5 *Recommended metal mask thickness : t=0.15mm 40.05 2.40.03 Polarity mark position O1.10.05 7.4MIN .7 O1.1 O0 Polarity mark position 2.40.03 1.50.05 E0.05 D0.05 0.60.05 0.350.03 E0.05 D0.05 0.60.03 0.350.03 2.40.03 5 0.0 .7 O0 1.80.05 Receptacle 6.9MIN 20.05 2.40.03 Header [FX8C**P-SV*] *Recommended metal mask thickness : t=0.15mm *If the inside (the connector lower side) of the SMT land isn't treated with insulation tape and so on, the area is considered as the prohibited area.(FX8C-S-SV5 isn't applied.) 7 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8C SeriesHigh-Speed (3.125Gbps) Stacking Connectors A0.3 B0.3 C +0.05 _0.2 D +0.05 _0.2 E0.2 (16.1) (11) Header (two-piece Connection Product) [FX8C-**/**P11-SVJ] (3.35) Polarity mark F0.1 (4.5) Unit:mm Number of Contacts A B C D E F FX8C-060/060P11-SVJ(71) 578-0651-1-71 Part Number CL No. 602 31.70 24.70 23.00 20.70 17.40 22.20 FX8C-080/080P11-SVJ(71) 578-0653-7-71 802 37.70 30.70 29.00 26.70 23.40 28.20 FX8C-100/100P11-SVJ(71) 578-0655-2-71 1002 43.70 36.70 35.00 32.70 29.40 34.20 FX8C-120/120P11-SVJ(71) 578-0656-5-71 1202 49.70 42.70 41.00 38.70 35.40 40.20 FX8C-140/140P11-SVJ(71) 578-0657-8-71 1402 55.70 48.70 47.00 44.70 41.40 46.20 RoHS YES Note 1: The two-piece connection product is packaged by tray. Note 2: Tray packaging product is not for board placement with automatic equipment. A0.3 B0.3 C +0.05 _0.2 D +0.05 _0.2 E0.2 (16.1) (11) [FX8C-**/**P11-SV1J] [FX8C-**/**P11-SV2J] [FX8C-**/**P11-SV4J] [FX8C-**/**P11-SV6J] (G) Polarity mark F0.1 (4.5) Unit: mm Part Number FX8C-060/060P11-SV1J(71) FX8C-060/060P11-SV2J(71) FX8C-060/060P11-SV4J(71) FX8C-060/060P11-SV6J(71) FX8C-080/080P11-SV1J(71) FX8C-080/080P11-SV2J(71) FX8C-080/080P11-SV4J(71) FX8C-080/080P11-SV6J(71) FX8C-100/100P11-SV1J(71) FX8C-100/100P11-SV2J(71) FX8C-100/100P11-SV4J(71) FX8C-100/100P11-SV6J(71) FX8C-120/120P11-SV1J(71) FX8C-120/120P11-SV2J(71) FX8C-120/120P11-SV4J(71) FX8C-120/120P11-SV6J(71) FX8C-140/140P11-SV1J(71) FX8C-140/140P11-SV2J(71) FX8C-140/140P11-SV4J(71) FX8C-140/140P11-SV6J(71) CL No. 578-0671-9-71 578-0691-6-71 578-0731-9-71 578-0751-6-71 578-0673-4-71 578-0693-1-71 578-0733-4-71 578-0753-1-71 578-0675-0-71 578-0695-7-71 578-0735-0-71 578-0755-7-71 578-0676-2-71 578-0696-0-71 578-0736-2-71 578-0756-0-71 578-0677-5-71 578-0697-2-71 578-0737-5-71 578-0757-2-71 Number of Contacts A B C D E F 602 31.70 . 24.70 23.00 20.70 17.40 22.20 802 37.70 30.70 29.00 26.70 23.40 28.20 1002 43.70 36.70 35.00 32.70 29.40 34.20 1202 49.70 42.70 41.00 38.70 35.40 40.20 1402 55.70 48.70 47.00 44.70 41.40 46.20 Note 1: The two-piece connection product is packaged by tray. Note 2: Tray packaging product is not for board placement with automatic equipment. Note 3: The locator material is installed between leads for the FX8C-**/**P11-SV6J type. 8 G 4.35 5.35 7.35 9.35 4.35 5.35 7.35 9.35 4.35 5.35 7.35 9.35 4.35 5.35 7.35 9.35 4.35 5.35 7.35 9.35 H 5.45 6.45 8.45 10.45 5.45 6.45 8.45 10.45 5.45 6.45 8.45 10.45 5.45 6.45 8.45 10.45 5.45 6.45 8.45 10.45 RoHS YES The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8C SeriesHigh-Speed (3.125Gbps) Stacking Connectors Receptacle (two-piece Connection Product) [FX8C-**/**S11-SVJ] (16.6) (11) A0.3 B0.3 C 0.2 -0 D 0.2 -0 E0.2 (3.4) Polarity mark(Rear side) F0.1 (4) Unit:mm Part Number CL No. Number of Contacts A B C D E F FX8C-060/060S11-SVJ(71) 578-0901-7-71 602 31.70 24.60 23.05 20.80 17.40 22.20 FX8C-080/080S11-SVJ(71) 578-0903-2-71 802 37.70 30.60 29.05 26.80 23.40 28.20 FX8C-100/100S11-SVJ(71) 578-0905-8-71 1002 43.70 36.60 35.05 32.80 29.40 34.20 FX8C-120/120S11-SVJ(71) 578-0906-0-71 1202 49.70 42.60 41.05 38.80 35.40 40.20 FX8C-140/140S11-SVJ(71) 578-0907-3-71 1402 55.70 48.60 47.05 44.80 41.40 46.20 Note 1: The two-piece connection product is packaged by tray. Note 2: Tray packaging product is not for board placement with automatic equipment. YES A0.3 B0.3 C 0.2 -0 D 0.2 -0 E0.2 (16.6) (11) [FX8C-**/**S11-SV5J] RoHS (8.4) Polarity mark(Rear side) F0.1 (4) Unit:mm Part Number CL No. Number of Contacts A B C D E F FX8C-060/060S11-SV5J(71) 578-0921-4-71 602 31.70 24.60 23.05 20.80 17.40 22.20 RoHS FX8C-080/080S11-SV5J(71) 578-0923-0-71 802 37.70 30.60 29.05 26.80 23.40 28.20 FX8C-100/100S11-SV5J(71) 578-0925-5-71 1002 43.70 36.60 35.05 32.80 29.40 34.20 FX8C-120/120S11-SV5J(71) 578-0926-8-71 1202 49.70 42.60 41.05 38.80 35.40 40.20 FX8C-140/140S11-SV5J(71) 578-0927-0-71 1402 55.70 48.60 47.05 44.80 41.40 46.20 YES Note 1: The two-piece connection product is packaged by tray. Note 2: Tray packaging product is not for board placement with automatic equipment. BPCB mounting pattern Header Receptacle [FX8C-** / **P 11-SVJ, SV1J] [FX8C-** / **P 11-SVJ, SV5J] 5 0.0 7.4MIN 40.05 O1.10.05 40.05 110.05 O1.10.05 F0.05 E0.05 0.60.05 0.350.03 2.40.03 O0.70.05 O0.7 0. 05 1.80.05 2.40.03 1.80.05 7 O0. *Recommended metal mask thickness : t=0.15mm Polarity mark position 7.4MIN 1.50.05 05 Polarity mark position 1.50.05 0. 6.9N 6.9MIN 20.05 20.05 O1.1 O 1 .10 0. .05 05 2.40.03 O0.7 110.05 2.40.03 E0.05 F0.05 0.60.05 0.350.03 *Recommended metal mask thickness : t=0.15mm *If the inside (the connector lower side) of the SMT land isn't treated with insulation tape and so on, the area is considered as the prohibited area.(Except FX8C-**/**S11-SV5J) 9 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8C SeriesHigh-Speed (3.125Gbps) Stacking Connectors BDetailed Figure After Joint Removal (Single Product in two-piece Connection Product) Header [FX8C-** / **P 11-SVJ] [FX8C-** / **P 11-SV1J] P=0.60.1 (0.4) (1.5) (0.75) (O0.6) (O0.9) t0.20.03w0.250.03 Polarity mark H0.25 Polarity mark (2.4) 5.10.3 6.5 0 -0.3 5.10.3 4.450.25 (0.75) (0.4) 6.5 0 -0.3 P=0.60.1 (2.4) (O0.6) (O0.9) t0.20.03w0.250.03 (2.4) (1.5) (2.4) Receptacle [FX8C-** / **S 11-SVJ] [FX8C-** / **S 11-SV5J] P=0.60.1 (O0.9) (2.4) 10 (O0.6) t0.20.03w0.250.03 (2.4) 5.60.3 Polarity mark(Rear side) Polarity mark(Rear side) (1.8) (0.75) 8.950.25 (0.75) 3.950.25 7 0 -0.3 5.60.3 7 0 -0.3 P=0.60.1 (O0.9) (2.4) (O0.6) t0.20.03w0.250.03 (2.4) (1.8) The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8C SeriesHigh-Speed (3.125Gbps) Stacking Connectors BConnector Precautions 1. Tolerance Clearance on Mating Side The effective contact length of the product is set to 2.0mm. Please use the product so as to set to less than 1.2mm the clearance between the header and the receptacle in the mating process. 2. Fixation Between Mounting Boards If this product is fixed only by mating force, Please consider the fixing method so as not to apply loads such as vibration, shock and so on. 3. Stacking General Tolerance in Mating Stack Amm A +0.3 -0.2 mm Note: Please Note that the above tolerance of the stacking height doesn't include the solder paste thickness. 4. Handling Two-piece Connection Product Both joint bar edges of the two-piece connection product are fixed by joints, while the mating process can't be performed in that state. Before the mating process, please remove the joint bars as if pull it up. (Don't remove the joint bars before mounting on the board. ) Before removing joint bar After removing joint bar 5. Mounting Temperature Profile (Reference) 260 (MAX 250c) 240 220c 220 200c 200 Temperature 180 160 140 150c (c) 0 HRS test conditions Test boardGlass epoxy 161mm100mm1.6mm thick Solder method :Reflow Solder composition :Paste, 96.5%Sn/3%Ag/0.5%Cu Metal mask : 0.15mm thick Reflow cycles : 2 cycles 90120s Pre-heating time (150 to 200c) MAX 60s Soldering Time (220c min.) Time (Second) The temperature profile is based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume/thickness and board size/thickness. Consult your solder paste and equipment manufacturer for specific recommendations. 6. Cautions This product is made as the thin formed product in order to be miniaturized. 11 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8C SeriesHigh-Speed (3.125Gbps) Stacking Connectors BPackaging Type Packaging Type Number of Contacts Packaged Product Pieces Tube packaging 60 contacts 80 contacts 100 contacts 120 contacts 140 contacts 21 pieces 17 pieces 14 pieces 12-pieces 10pieces Deliver the multiplied pieces. (Example) In case of 60 contacts,21 pieces, 42-pieces,... Sales Unit 550mm2mm Total Tube Length 44mm Tape Width 56mm Product Pitch 72mm 12mm Embossed Tape Packaging Emboss Reel Diameter Refer to the table on page 13 in this catalog. Packaged Product Pieces Refer to the table on page 13 in this catalog. Sales Unit Per reel *The above packaging type is , as listed for the single product only. In addition, the packaging type of the two-piece connection product is the tray packaging. BPackaging Specification [Tube packaging] Receptacle [FX8C-**S-SV (91)] [FX8C-**S-SV5 (91)] (9.5) 5502 FX8C-P-SV (A) MADE IN JAPAN Polarity mark 5502 Polarity mark (10) Header [FX8-**P-SV (91)] [FX8-**P-SV1 (91)] [FX8-**P-SV2 (91)] [FX8-**P-SV4 (91)] [FX8-**P-SV6 (91)] FX8C-S-SV (A) MADE IN JAPAN Polarity mark(Rear side) P/S Header Receptacle 12 Part Number A FX8C-**P-SV0 (91) 9 FX8C-**P-SV1 (91) 10 FX8C-**P-SV2 (91) 11 FX8C-**P-SV4 (91) 13 FX8C-**P-SV6 (91) 15 FX8C-**S-SV0 (91) 7.4 FX8C-**S-SV5 (91) 12.4 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8C SeriesHigh-Speed (3.125Gbps) Stacking Connectors [Embossed Tape Package] Carrier Size Pattern UNREELING DIRECTION C 12 4 44 [56] [72] 20.2 [26.2] [34.2] 1.7 40.4 [52.4] [68.4] 2 0.4 or 0.5 1.75 D 1.5 A B * The above figure represents the case of the receptacle connector. Unit: mm P/S Header Receptacle Part Number A B C D E Product Pieces FX8C-**P-SV0 (92) 5.5 7.9 5.2 1.2 O370 1000 pieces FX8C-**P-SV1 (92) 5.5 7.9 6.2 1.2 O370 1000 pieces FX8C-**P-SV2 (92) 5.5 7.9 7.2 1.2 O330 0500 pieces FX8C-**P-SV4 (92) 5.5 7.9 9.2 1.2 O370 0500 pieces FX8C-**P-SV6 (92) 5.5 7.9 11.2 1.2 O370 0500 pieces FX8C-**S-SV0 (92) 6.0 8.4 4.3 1.2 O330 1000 pieces Note 1 FX8C-**S-SV5 (92) 6.0 8.4 9.3 1.2 O370 0500 pieces Note 2 Note 2 ** : Number of Contacts 13 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8C SeriesHigh-Speed (3.125Gbps) Stacking Connectors Reel State Size Pattern (FREE) 44.4[56.4][72.4] E TRAILER O80(Note.1) O1 3 2 EQUIPPED (1000 CONNECTORS) EMBOSSED CARRIER TAPE LEADER(400mm MIN) TOP COVER TAPE 10 EMPTY COMPONENT COMPARTMENTS MIN 10 EMPTY COMPONENT COMPARTMENTS MIN Note 1: E dimension for FX8C-140S-SV(92) is O370, core dia. is O100. Note 2: E dimension for FX8C-120P-SV2(92), FX8C-120S-SV5(92), FX8C-140S-SV5(92) is O380. 14 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. 0.6mm Pitch Stacking Height 3mm to 16mm Connector FX8, FX8C Series FX8 Series FX8C Series Note that FX8 series and FX8C series are not mated with each other. Features 1. Stacking Height 3mm to 16mm available Stacking Height 3,4mm-FX8 Series The board to board stacking height can correspond to 3mm~16mm. 2. SMT Coplanarity The coplanarity of the SMT solder area lead is maintained at the high accuracy of less than 0.1mm. 3,4mm 3. Mating Guide The very small and guide rib is provided, and secures 0.6mm self-alignment, considering the mating operativity into accounts. 4. Mis-insertion Prevention The boss prevents mis-insertion in the board to cause due to the boss position and boss diameter. Stacking Height 5 to 16mm-FX8C Series 5 to 16mm Applications Note pc, business equipments, which require miniaturization or light-weight A166 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8, FX8C Series0.6mm Pitch Stacking Height 3mm to 16mm Connector FX8C Series Product Specifications Rating Current rating 0.4A Operating Temperature Range -55c to +85c Note 1. Storage Temperature Range -10c to +60c Note 2. Voltage rating 100V AC Operating Humidity Range -40% to 80% Storage Humidity Range 40% to 70% Item Specification Condition 1. Insulation Resistance 100M ohms min. 250V DC 2. Withstanding voltage No flashover or insulation breakdown. 300V AC/1 minute 3. Contact Resistance 80m ohms max. 100mA 4. Vibration No electrical discontinuity of 1s or more Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 5. Humidity (Steady state) Contact resistance: 100m ohms max.Insulation resistance: 100M ohms min. 96 hours at temperature of 40c and humidity of 90% to 95% 6. Temperature Cycle Contact resistance: 100m ohms max.Insulation resistance: 100M ohms min. (-55c: 30 minutes, 15 to 35c: 2 to 3 minutes (-85c: 30 minutes, 15 to 35c: 2 to 3minutes) 5 cycles 7. Durability (Mating/un-mating) Contact resistance: 100m ohms max. 50 cycles 8. Resistance to Soldering heat No deformation of components affecting performance. Reflow: At the recommended temperature profile Manual soldering: 360c for 5 seconds Note 1 : Includes temperature rise caused by current flow. Note 2 : The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation. Note 3 : Slight variations in color of the plastic compounds do not affect form ,fit or function of the connector. Note 4 : FX8C-*P-SV(*),FX8C-*S-SV(*) is gold plated. Note 5 : Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. Material Part Material Finish Remarks Insulator PBS Light brown UL94V-0 Header Contact Phosphor bronze Contact area Lead area Gold plated Tin plated(Note 4) ------- Receptacle Contact Phosphor bronze Contact area Lead area Gold plated Tin plated(Note 4) ------- Ordering Information Single Product - 120 P - SV 1 (91) FX8C q w q Series Name : FX8C e r t y w Number of Contacts :60, 80, 90, 120, 140 t Product height variation Blank : Standard (Minimum low profile) 1: +1mm . . . . . . 3:+3mm e Connector type y Packaging Type P :Header S :Receptacle r Contact type (71) : Tray packaging SV :Board vertical type (91) : Tube packaging (92) : Embossed tape package two-piece Connection Product FX8C - 120/120 P 11 - SV 1 J q w e r t y u q Series Name :FX8C r Connector to Connector Pitch w Number of Contacts: 602, 802, 902, t Contact type e Connector Type : SV : Board vertical type Example: 120/120 = 240 contacts y Product Height VariationBlank : Standard (Minimum lot profile) 1:+1mm . . . . . . 3:+3mm P : Header u J: two-piece connection product 1002, 1202, 1402 S : Receptacle *The standard packaging of the two-piece connection product is the tray packaging. A174 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8, FX8C Series0.6mm Pitch Stacking Height 3mm to 16mm Connector FX8C-**S-SV FX8C-**/**S11-SVJ FX8C-**S-SV5 FX8C-**/**S11-SV5J FX8C-**P-SV FX8C-**/**P11-SVJ 5mm 10mm FX8C-**P-SV1 FX8C-**/**P11-SV1J 6mm 11mm FX8C-**P-SV2 FX8C-**/**P11-SV2J 7mm 12mm FX8C-**P-SV4 FX8C-**/**P11-SV4J 9mm 14mm FX8C-**P-SV6 FX8C-**/**P11-SV6J 11mm 16mm Header Receptacle 5 to 16 BStacking Height Variation A175 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8, FX8C Series0.6mm Pitch Stacking Height 3mm to 16mm Connector Header (Single Product) [FX8C-**P-SV] Unit:mm Part Number FX8C-060P-SV(92) FX8C-080P-SV(92) FX8C-100P-SV(92) FX8C-120P-SV(92) FX8C-140P-SV(92) CL No. Number of Contacts 60 578-0501-9-92 80 578-0503-4-92 100 578-0505-0-92 120 578-0506-2-92 140 578-0507-5-92 A 24.60 30.60 36.60 42.60 48.60 B 23.00 29.00 35.00 41.00 47.00 **71 : Tray packaging product 91: Tube packaging product 92 : Embossed tape packaging product Note 1: To order the tube packaging product, please determine the quantity for delivery, multiplying the tube packaging product by an integer. C 20.70 26.70 32.70 38.70 44.70 D 17.40 23.40 29.40 35.40 41.40 E Tube packaging Quantity (Pieces) RoHS 22.20 21 28.20 17 34.20 14 YES 40.20 12 46.20 10 Note 2: The embossed tape packaging product is prepared for 60 and 80 contacts only. In addition, the product will be procured per reel unit. Please refer to the delivery form item on page A182 for details. Note 3: Tray packaging product is not for board placement with automatic equipment. [FX8C-**P-SV1] [FX8C-**P-SV2] [FX8C-**P-SV4] [FX8C-**P-SV6] Unit: mm Note 5 Part Number FX8C-060P-SV1(92) FX8C-060P-SV2(92) FX8C-060P-SV4(92) FX8C-060P-SV6(92) FX8C-080P-SV1(92) FX8C-080P-SV2(92) FX8C-080P-SV4(92) FX8C-080P-SV6(92) FX8C-100P-SV1(92) FX8C-100P-SV2(92) FX8C-100P-SV4(92) FX8C-100P-SV6(92) FX8C-120P-SV1(92) FX8C-120P-SV2(92) FX8C-120P-SV4(92) FX8C-120P-SV6(92) FX8C-140P-SV1(92) FX8C-140P-SV2(92) FX8C-140P-SV4(92) FX8C-140P-SV6(93) CL No. 578-0521-6-92 578-0541-3-92 578-0581-8-92 578-0601-3-92 578-0523-1-92 578-0543-9-92 578-0583-3-92 578-0603-9-92 578-0525-7-92 578-0545-4-92 578-0585-9-92 578-0605-4-92 578-0526-0-92 578-0546-7-92 578-0586-1-92 578-0606-7-92 578-0527-2-92 578-0547-0-92 578-0587-4-92 578-0607-0-93 Number of Contacts A B C D E 60 24.60 23.00 20.70 17.40 22.20 80 30.60 29.00 26.70 23.40 28.20 100 36.60 35.00 32.70 29.40 34.20 120 42.60 41.00 38.70 35.40 40.20 140 48.60 47.00 44.70 41.40 46.20 F Tube packaging Quantity (Pieces) RoHS 5.45 6.45 21 8.45 10.45 5.45 6.45 17 8.45 10.45 5.45 6.45 YES 14 8.45 10.45 5.45 6.45 12 8.45 10.45 5.45 6.45 10 8.45 10.45 ** 71: Tray packaging product 91: Tube packaging product 92: Embossed tape packaging product Note 1: To order the tube packaging product, please determine a quantity for delivery,multiplying the tube packaging product by an integer. Note 2: The embossed tape packaging product is prepared for 60 and 80 contacts only. In addition, the product will be sold per reel unit. Please refer to the packaging specification item on page A182 for details. Note 3: The locator material is installed between leads for the FX8C-P-SV6 type. Note 4: Tray packaging product is not for board placement with automatic equipment. Note 5: (93) spec is with vacuum pick-up tape, embossed tape packaging product. A176 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8, FX8C Series0.6mm Pitch Stacking Height 3mm to 16mm Connector Receptacle (Single Product) [FX8C-**S-SV] Unit:mm Part Number CL No. Number of Contacts FX8C-060S-SV(92) 578-0801-2-92 60 24.60 23.05 20.80 17.40 22.20 A B C D E Tube packaging Quantity (Pieces) RoHS 21 FX8C-080S-SV(92) 578-0803-8-92 80 30.60 29.05 26.80 23.40 28.20 17 FX8C-100S-SV(92) 578-0805-3-92 100 36.60 35.05 32.80 29.40 34.20 14 FX8C-120S-SV(92) 578-0806-6-92 120 42.60 41.05 38.80 35.40 40.20 12 FX8C-140S-SV(92) 578-0807-9-92 140 48.60 47.05 44.80 41.40 46.20 10 YES ** 71: Tray packaging product 91: Tube packaging product 92: Embossed tape packaging product Note 1: To order the tube packaging product, please determine a quantity for delivery,multiplying the tube packaging product by an integer. Note 2: The embossed tape packaging product is prepared for 60 and 80 contacts only. In addition, the product will be procured per reel unit. Please refer to the packaging specification item on page A182 for details. Note 3: Tray packaging product is not for board placement with automatic equipment. [FX8C-**S-SV5] Unit:mm Part Number CL No. Number of Contacts FX8C-060S-SV5(92) 578-0821-0-92 60 24.60 23.05 20.80 17.40 22.20 A B C D E Tube packaging Quantity (Pieces) RoHS 21 FX8C-080S-SV5(92) 578-0823-5-92 80 30.60 29.05 26.80 23.40 28.20 17 FX8C-100S-SV5(92) 578-0825-0-92 100 36.60 35.05 32.80 29.40 34.20 14 FX8C-120S-SV5(92) 578-0826-3-92 120 42.60 41.05 38.80 35.40 40.20 12 FX8C-140S-SV5(92) 578-0827-6-92 140 48.60 47.05 44.80 41.40 46.20 10 YES ** 71: Tray packaging product 91: Tube packaging product 92: Embossed tape packaging product Note 1: To order the tube packaging product, please determine a quantity for delivery,multiplying the tube packaging product by an integer. Note 2: The embossed tape package product is prepared for 60 and 80 contacts only. In addition, the product will be procured per reel unit. Please refer to the packaging specification item on page A182 for details. Note 3: Tray packaging product is not for board placement with automatic equipment. BPCB mounting pattern A177 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8, FX8C Series0.6mm Pitch Stacking Height 3mm to 16mm Connector Header (two-pieces Connection Product) [FX8C-**/**P11-SVJ] Unit:mm Number of Contacts A B C D E F FX8C-060/060P11-SVJ(71) 578-0651-1-71 Part Number CL No. 602 31.70 24.70 23.00 20.70 17.40 22.20 FX8C-080/080P11-SVJ(71) 578-0653-7-71 802 37.70 30.70 29.00 26.70 23.40 28.20 FX8C-100/100P11-SVJ(71) 578-0655-2-71 1002 43.70 36.70 35.00 32.70 29.40 34.20 FX8C-120/120P11-SVJ(71) 578-0656-5-71 1202 49.70 42.70 41.00 38.70 35.40 40.20 FX8C-140/140P11-SVJ(71) 578-0657-8-71 1402 55.70 48.70 47.00 44.70 41.40 46.20 RoHS YES Note 1: The two-piece connection product is packaged by tray. Note 2: Tray packaging product is not for board placement with automatic equipment. [FX8C-**/**P11-SV1J] [FX8C-**/**P11-SV2J] [FX8C-**/**P11-SV4J] [FX8C-**/**P11-SV6J] Unit: mm Part Number FX8C-060/060P11-SV1J(71) FX8C-060/060P11-SV2J(71) FX8C-060/060P11-SV4J(71) FX8C-060/060P11-SV6J(71) FX8C-080/080P11-SV1J(71) FX8C-080/080P11-SV2J(71) FX8C-080/080P11-SV4J(71) FX8C-080/080P11-SV6J(71) FX8C-100/100P11-SV1J(71) FX8C-100/100P11-SV2J(71) FX8C-100/100P11-SV4J(71) FX8C-100/100P11-SV6J(71) FX8C-120/120P11-SV1J(71) FX8C-120/120P11-SV2J(71) FX8C-120/120P11-SV4J(71) FX8C-120/120P11-SV6J(71) FX8C-140/140P11-SV1J(71) FX8C-140/140P11-SV2J(71) FX8C-140/140P11-SV4J(71) FX8C-140/140P11-SV6J(71) CL No. 578-0671-9-71 578-0691-6-71 578-0731-9-71 578-0751-6-71 578-0673-4-71 578-0693-1-71 578-0733-4-71 578-0753-1-71 578-0675-0-71 578-0695-7-71 578-0735-0-71 578-0755-7-71 578-0676-2-71 578-0696-0-71 578-0736-2-71 578-0756-0-71 578-0677-5-71 578-0697-2-71 578-0737-5-71 578-0757-2-71 Number of Contacts A B C D E F 602 31.70 . 24.70 23.00 20.70 17.40 22.20 802 37.70 30.70 29.00 26.70 23.40 28.20 1002 43.70 36.70 35.00 32.70 29.40 34.20 1202 49.70 42.70 41.00 38.70 35.40 40.20 1402 55.70 48.70 47.00 44.70 41.40 46.20 Note 1: The two-piece connection product is packaged by tray. Note 2: Tray packaging product is not for board placement with automatic equipment. Note 3: The locator material is installed between leads for the FX8C-**/**P11-SV6J type. A178 G 4.35 5.35 7.35 9.35 4.35 5.35 7.35 9.35 4.35 5.35 7.35 9.35 4.35 5.35 7.35 9.35 4.35 5.35 7.35 9.35 H 5.45 6.45 8.45 10.45 5.45 6.45 8.45 10.45 5.45 6.45 8.45 10.45 5.45 6.45 8.45 10.45 5.45 6.45 8.45 10.45 RoHS YES The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8, FX8C Series0.6mm Pitch Stacking Height 3mm to 16mm Connector Receptacle (two-piece Connection Product) [FX8C-**/**S11-SVJ] Unit:mm Part Number CL No. Number of Contacts A B C D E F FX8C-060/060S11-SVJ(71) 578-0901-7-71 602 31.70 24.60 23.05 20.80 17.40 22.20 FX8C-080/080S11-SVJ(71) 578-0903-2-71 802 37.70 30.60 29.05 26.80 23.40 28.20 FX8C-100/100S11-SVJ(71) 578-0905-8-71 1002 43.70 36.60 35.05 32.80 29.40 34.20 FX8C-120/120S11-SVJ(71) 578-0906-0-71 1202 49.70 42.60 41.05 38.80 35.40 40.20 FX8C-140/140S11-SVJ(71) 578-0907-3-71 1402 55.70 48.60 47.05 44.80 41.40 46.20 RoHS YES Note 1: The two-piece connection product is packaged by tray. Note 2: Tray packaging product is not for board placement with automatic equipment. [FX8C-**/**S11-SV5J] Unit:mm Part Number CL No. Number of Contacts A B C D E F FX8C-060/060S11-SV5J(71) 578-0921-4-71 602 31.70 24.60 23.05 20.80 17.40 22.20 FX8C-080/080S11-SV5J(71) 578-0923-0-71 802 37.70 30.60 29.05 26.80 23.40 28.20 FX8C-100/100S11-SV5J(71) 578-0925-5-71 1002 43.70 36.60 35.05 32.80 29.40 34.20 FX8C-120/120S11-SV5J(71) 578-0926-8-71 1202 49.70 42.60 41.05 38.80 35.40 40.20 FX8C-140/140S11-SV5J(71) 578-0927-0-71 1402 55.70 48.60 47.05 44.80 41.40 46.20 RoHS YES Note 1: The two-piece connection product is packaged by tray. Note 2: Tray packaging product is not for board placement with automatic equipment. BPCB mounting pattern A179 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8, FX8C Series0.6mm Pitch Stacking Height 3mm to 16mm Connector BDetailed Figure After Joint Removal (Single Product in two-piece Connection Product) A180 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8, FX8C Series0.6mm Pitch Stacking Height 3mm to 16mm Connector BConnector Precautions 1. Tolerance Clearance on Mating Side The effective contact length of the product is set to 2.0mm. Please use the product so as to set to less than 12mm the clearance between the header and the receptacle in the mating process. 2. Fixation Between Mounting Boards If this product is fixed only by mating force, Please consider the fixing method so as not to apply loads such as vibration, shock and so on. 3. Stacking General Tolerance in Mating Stack Amm A +0.3 -0.2 mm Note: Please Note that the above tolerance of the stacking height doesn't include the solder paste thickness. 4. Handling Two-piece Connection Product Both joint bar edges of the two-piece connection product are fixed by joints, while the mating process can't be performed in that state. Before the mating process, please remove the joint bars as if pull it up. (Don't remove the joint bars before mounting on the board. ) Before removing joint bar After removing joint bar 5. Mounting Temperature Profile (Reference) 260 (MAX 250c) 240 220c 220 200c 200 Temperature 180 160 140 150c (c) 0 HRS test conditions Test boardGlass epoxy 161mm100mm1.6mm thick Solder method :Reflow Solder composition :Paste, 96.5%Sn/3%Ag/0.5%Cu Metal mask : 0.15mm thick Reflow cycles : 2 cycles 90120s Pre-heating time (150 to 200c) MAX 60s Soldering Time (220c min.) Time (Second) The temperature profile is based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume/thickness and board size/thickness. Consult your solder paste and equipment manufacturer for specific recommendations. 6. Cautions This product is made as the thin formed product in order to be miniaturized. A181 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8, FX8C Series0.6mm Pitch Stacking Height 3mm to 16mm Connector BPackaging Type Packaging Type Number of Contacts Packaged Product Pieces Tube packaging Sales Unit 60 contacts 80 contacts 100 contacts 120 contacts 140 contacts 21 pieces 17 pieces 14 pieces 12-pieces 10pieces Deliver the multiplied pieces. (Example) In case of 20 contacts,21 pieces, 4two-pieces,... 550mm2mm Total Tube Length 44mm Tape Width Product Pitch 12mm Embossed Tape Packaging Emboss Reel Diameter Refer to the table on page A183 in this catalog. Packaged Product Pieces Refer to the table on page A183 in this catalog. Sales Unit Per reel *The above packaging type is , as listed for the single product only. In addition, the packaging type of the two-piece connection product is the tray packaging. BPackaging Specification [Tube packaging] Header [FX8-**P-SV (91)] [FX8-**P-SV1 (91)] [FX8-**P-SV2 (91)] [FX8-**P-SV4 (91)] [FX8-**P-SV6 (91)] Receptacle [FX8C-**S-SV (91)] [FX8C-**S-SV5 (91)] P/S Header Receptacle A182 Part Number 56mm A FX8C-**P-SV0 (91) 9 FX8C-**P-SV1 (91) 10 FX8C-**P-SV2 (91) 11 FX8C-**P-SV4 (91) 13 FX8C-**P-SV6 (91) 15 FX8C-**S-SV0 (91) 7.4 FX8C-**S-SV5 (91) 12.4 72mm The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FX8, FX8C Series0.6mm Pitch Stacking Height 3mm to 16mm Connector [Embossed Tape Package] Carrier Size Pattern Unit: mm P/S Header Receptacle Part Number A B C D E Product Pieces FX8C-**P-SV0 (92) 5.5 7.9 5.2 1.2 O370 1000 pieces FX8C-**P-SV1 (92) 5.5 7.9 6.2 1.2 O370 1000 pieces FX8C-**P-SV2 (92) 5.5 7.9 7.2 1.2 O330 0500 pieces FX8C-**P-SV4 (92) 5.5 7.9 9.2 1.2 O370 0500 pieces Note 2 FX8C-**P-SV6 (92) 5.5 7.9 11.2 1.2 O370 0500 pieces FX8C-**S-SV0 (92) 6.0 8.4 4.3 1.2 O330 1000 pieces Note 1 FX8C-**S-SV5 (92) 6.0 8.4 9.3 1.2 O370 0500 pieces Note 2 ** : Number of Contacts (Note 1) Reel State Size Pattern (FREE) Note 1: E dimension for FX8C-140S-SV(92) is O370, core dia. is O100. Note 2: E dimension for FX8C-120P-SV2(92), FX8C-120S-SV5(92), FX8C-140S-SV5(92) is O380. A183