© Semiconductor Components Industries, LLC, 2012
July, 2012 Rev. 3
1Publication Order Number:
NE5534/D
NE5534, SA5534, SE5534,
NE5534A, SA5534A,
SE5534A
Single Low Noise
Operational Amplifier
The NE/SA/SE5534/5534A are single high-performance low noise
operational amplifiers. Compared to other operational amplifiers,
such as TL083, they show better noise performance, improved output
drive capability, and considerably higher small-signal and power
bandwidths.
This makes the devices especially suitable for application in high
quality and professional audio equipment, in instrumentation and
control circuits and telephone channel amplifiers. The op amps are
internally compensated for gain equal to, or higher than, three. The
frequency response can be optimized with an external compensation
capacitor for various applications (unity gain amplifier, capacitive
load, slew rate, low overshoot, etc.).
Features
Small-Signal Bandwidth: 10 MHz
Output Drive Capability: 600 W, 10 VRMS at VS = "18 V
Input Noise Voltage: 4nVńHz
Ǹ
DC Voltage Gain: 100000
AC Voltage Gain: 6000 at 10 kHz
Power Bandwidth: 200 kHz
Slew Rate: 13 V/ms
Large Supply Voltage Range: "3.0 to "20 V
PbFree Packages are Available
Applications
Audio Equipment
Instrumentation and Control Circuits
Telephone Channel Amplifiers
Medical Equipment
http://onsemi.com
See detailed ordering and shipping information in the package
dimensions section on page 8 of this data sheet.
ORDERING INFORMATION
PIN CONNECTIONS
SOIC8
D SUFFIX
CASE 751
Top View
PDIP8
N SUFFIX
CASE 626
1
8
8
7
6
54
3
2
1BALANCE/
COMPENSATION
V+
OUTPUT
COMPENSATION
BALANCE
INVERTING INPUT
NON-INVERTING
V
D, N Packages
1
8
See general marking information in the device marking
section on page 8 of this data sheet.
DEVICE MARKING INFORMATION
NE5534, SA5534, SE5534, NE5534A, SA5534A, SE5534A
http://onsemi.com
2
1
2
3
4
6
7
5
8
Figure 1. Equivalent Schematic
MAXIMUM RATINGS
Rating Symbol Value Unit
Supply Voltage VS"22 V
Input Voltage VIN "V Supply V
Differential Input Voltage (Note 1) VDIFF "0.5 V
Operating Temperature Range
NE
SA
SE
Tamb 0 to +70
40 to +85
55 to +125
°C
Storage Temperature Range Tstg 65 to +150 °C
Junction Temperature Tj150 °C
Power Dissipation at 25°C
N Package
D Package
PD1150
750
mW
Thermal Resistance, JunctiontoAmbient
N Package
D Package
RqJA 130
158
°C/W
Output Short-Circuit Duration (Note 2) Indefinite
Lead Soldering Temperature (10 sec max) Tsld 230 °C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Diodes protect the inputs against overvoltage. Therefore, unless current-limiting resistors are used, large currents will flow if the differential input
voltage exceeds 0.6 V. Maximum current should be limited to "10 mA.
2. Output may be shorted to ground at VS = "15 V, Tamb = 25°C. Temperature and/or supply voltages must be limited to ensure dissipation rating
is not exceeded.
NE5534, SA5534, SE5534, NE5534A, SA5534A, SE5534A
http://onsemi.com
3
DC ELECTRICAL CHARACTERISTICS (Tamb = 25°C; VS = "15 V, unless otherwise noted.) (Notes 3, 4 and 5)
Characteristic Symbol Test Conditions
NE/SA5534/5534A SE5534/5534A
Unit
Min Typ Max Min Typ Max
VOS 0.5 4.0 0.5 2.0 mV
Offset Voltage Overtemperature 5.0 3.0 mV
DVOS/DT5.0 5.0 mV/°C
IOS 20 300 10 200 nA
Offset Current Overtemperature 400 500 nA
DIOS/DT200 200 pA/°C
IB500 1500 400 800 nA
Input Current Overtemperature 2000 1500 nA
DIB/DT5.0 5.0 nA/°C
Supply Current
Per Op Amp
ICC Overtemperature
4.0
8.0
10
4.0
6.5
9.0
mA
Common Mode Input Range VCM "12 "13 "12 "13 V
Common Mode Rejection Ratio CMRR 70 100 80 100 dB
Power Supply Rejection Ratio PSRR 10 100 10 50 mV/V
Large-Signal Voltage Gain AVOL RL 600 W,
VO = "10 V
Overtemperature
25
15
100
50
25
100
V/mV
Output Swing VOUT RL w 600 W"12 "13 "12 "13 V
Overtemperature "10 "12 "10 "12
RL w 600 W;
VS = "18 V "15 "16 "15 16
RL w 2.0 kW"13 "13.5 "13 "13.5
Overtemperature "12 "12.5 "12 "12.5
Input Resistance RIN 30 100 50 100 kW
Output Short Circuit Current ISC 38 38 mA
3. For NE5534/5534A, TMIN = 0°C, TMAX = 70°C.
4. For SA5534/5534A, TMIN = 40°C, TMAX = +85°C.
5. For SE5534/5534A, TMIN = 55°C, TMAX = +125°C.
NE5534, SA5534, SE5534, NE5534A, SA5534A, SE5534A
http://onsemi.com
4
AC ELECTRICAL CHARACTERISTICS (Tamb = 25°C; VS = "15 V, unless otherwise noted.)
Characteristic Symbol Test Conditions
NE/SA5534/5534A SE5534/5534A
Unit
Min Typ Max Min Typ Max
Output Resistance ROUT AV = 30 dB
closed-loop
f = 10 kHz;
RL = 600 W;
CC = 22 pF
0.3 0.3 W
Transient Response Voltage-follower,
VIN = 50 mV
RL = 600 W,
CC = 22 pF,
CL = 100 pF
Rise Time tR20 20 ns
Overshoot 20 20 %
Transient Response VIN = 50 mV,
RL = 600 W,
CC = 47 pF,
CL = 500 pF
Rise Time tR50 50 ns
Overshoot 35 35 %
Gain AVf = 10 kHz, CC = 0 6.0 6.0 V/mV
f = 10 kHz,
CC = 22 pF
2.2 2.2
Gain Bandwidth Product GBW CC = 22 pF,
CL = 100 pF
10 10 MHz
Slew Rate SR CC = 0 13 13 V/ms
CC = 22 pF 6.0 6.0
Power Bandwidth VOUT = "10 V,
CC = 0 pF
200 200 kHz
VOUT = "10 V,
CC = 22 pF
95 95
VOUT = "14 V,
RL = 600 W,
CC = 22 pF,
VCC = "18 V
70 70
ELECTRICAL CHARACTERISTICS (Tamb = 25°C; VS = 15 V, unless otherwise noted.)
Characteristic Symbol Test Conditions
NE/SA/SE5534 NE/SA/SE5534A
Unit
Min Typ Max Min Typ Max
Input Noise Voltage VNOISE fO = 30 Hz
fO = 1.0 kHz
7.0
4.0
5.5
3.5
7.0
4.5
nV/Hz
Input Noise Current INOISE fO = 30 Hz
fO = 1.0 kHz
2.5
0.6
1.5
0.4
pA/Hz
Broadband Noise Figure f = 10 Hz to
20 kHz;
RS = 5.0 kW
0.9 dB
Channel Separation f = 1.0 kHz;
RS = 5.0 kW
110 110 dB
NE5534, SA5534, SE5534, NE5534A, SA5534A, SE5534A
http://onsemi.com
5
TYPICAL PERFORMANCE CHARACTERISTICS
GAIN (dB)
(nVńHz
Ǹ)
10 102103104105106107
120
80
40
0
-40
f (Hz)
16
12
8
4
0
04080
102103104105106107
40
30
20
10
0
80
60
40
20
0
-55 -25 0 25 50 75 100 +125 -55 -25 0 25 50 75 100 +125
1,4
1,2
0,8
0,4
0
30
20
10
0
01020
01020
0
2
4
6
102
10
1
101
102
10 102103104
CC(pF)
f (Hz)
f (Hz)
T
amb (oC) T
amb (oC)
TYP TYP
TYP
TYP
TYP
NEG
POS
CC =
0pF
22pF
47pF
CC = 0
CC = 22pF S
(V/ms)
(V)
Vo(p-p)
IO
(mA)
II
(mA)
VIN (V)
IP
IN
(mA)
Vp; -VN (V) Vp; -VN (V)
Figure 2. Open-Loop
Frequency Response
Figure 3. Slew Rate as a
Function of Compensation
Capacitance
GAIN (dB)
60
40
20
0
-20
103104105106107108
f (Hz)
CC = 0; RF = 10kW; RE = 100W
CC = 0; RF = 9kW; RE = 1kW
CC = 22pF; RF = 1kW; RE =
Figure 4. ClosedLoop
Frequency Response
Figure 5. LargeSignal
Frequency Response
Figure 6. Output
ShortCircuit Current
Figure 7. Input Bias
Current
Figure 8. Input CommonMode
Voltage Range
Figure 9. Supply Current
Per Op Amp
Figure 10. Input Noise
Voltage Density
TYPICAL VALUES
58
CC
VS = +15V TYPICAL VALUES
VS = +15V
TYPICAL VALUES
VS = +15V VS = +15V
TYPICAL VALUES IO = 0
NE5534, SA5534, SE5534, NE5534A, SA5534A, SE5534A
http://onsemi.com
6
TYPICAL PERFORMANCE CHARACTERISTICS
RS (W)
(pAńHz
Ǹ)
(nVńHz
Ǹ)
102
10
1
101
102
10 102103104
f (Hz)
TYP
Figure 11. Input Noise
Current Density
10 102103104105106
Figure 12. Total Input
Noise Density
01020
RS (W)
Figure 13. Broadband Input
Noise Voltage
Vn(rms)
In(rms)
106
105
104
103
102
10
1
101
102
Vn(rms)
(mV)
102
10
1
101
102
10Hz
1kHz
THERMAL NOISE
OF SOURCE
RESISTANCE
10Hz TO 20kHz
200Hz TO 4kHz
TYPICAL VALUES TYPICAL VALUES
NE5534, SA5534, SE5534, NE5534A, SA5534A, SE5534A
http://onsemi.com
7
TEST LOAD CIRCUITS
CC
RS
RE
VI
100kW
22kW
600W
25W
RF
1
8
5
7
6
4
3
2
-
+
+
-
2
3
8
5
6
100pF
V+
V-
Figure 14. Frequency Compensation and
Offset Voltage Adjustment Circuit
Figure 15. Closed-Loop Frequency Response
5534
5534
CC
(nVńHz
Ǹ)
(nVńHz
Ǹ)
CAL
OSC
POWER
SUPPLY
CAL
METER
+VCC -VCC
+40dB
10kW
100W
TEST BOARD
GND
1WDUT
+
-
BANDPASS
AT 1kHz
BANDPASS
AT 30Hz
Figure 16. Noise Test Block Diagram
NE5534, SA5534, SE5534, NE5534A, SA5534A, SE5534A
http://onsemi.com
8
SA5234xN
AWL
YYWWG
PDIP8
N SUFFIX
CASE 626
SOIC8
D SUFFIX
CASE 751
x = Blank or A
A = Assembly Location
WL, L = Wafer Lot
YY, Y = Year
WW, W = Work Week
G or G= PbFree Package
MARKING DIAGRAMS
N5234
ALYWA
G
1
8
S5234
ALYWA
G
1
8
S5234
ALYW
G
1
8
NE5234xN
AWL
YYWWG
SE5234xN
AWL
YYWWG
ORDERING INFORMATION
Device Description Temperature Range Shipping
NE5534AD 8Pin Plastic Small Outline (SO8) Package 0 to +70°C98 Units / Rail
NE5534ADG 8Pin Plastic Small Outline (SO8) Package (PbFree) 0 to +70°C98 Units / Rail
NE5534ADR2 8Pin Plastic Small Outline (SO8) Package 0 to +70°C2500 / Tape & Reel
NE5534ADR2G 8Pin Plastic Small Outline (SO8) Package (PbFree) 0 to +70°C2500 / Tape & Reel
NE5534AN 8Pin Plastic Dual InLine Package (PDIP8) 0 to +70°C50 Units / Rail
NE5534ANG 8Pin Plastic Dual InLine Package (PDIP8) (PbFree) 0 to +70°C50 Units / Rail
NE5534D 8Pin Plastic Small Outline (SO8) Package 0 to +70°C98 Units / Rail
NE5534DG 8Pin Plastic Small Outline (SO8) Package (PbFree) 0 to +70°C98 Units / Rail
NE5534DR2 8Pin Plastic Small Outline (SO8) Package 0 to +70°C2500 / Tape & Reel
NE5534DR2G 8Pin Plastic Small Outline (SO8) Package (PbFree) 0 to +70°C2500 / Tape & Reel
NE5534N 8Pin Plastic Dual InLine Package (PDIP8) 0 to +70°C50 Units / Rail
NE5534NG 8Pin Plastic Dual InLine Package (PDIP8) (PbFree) 0 to +70°C50 Units / Rail
SA5534AD 8Pin Plastic Small Outline (SO8) Package 40 to +85°C98 Units / Rail
SA5534ADG 8Pin Plastic Small Outline (SO8) Package (PbFree) 40 to +85°C98 Units / Rail
SA5534ADR2 8Pin Plastic Small Outline (SO8) Package 40 to +85°C2500 / Tape & Reel
SA5534ADR2G 8Pin Plastic Small Outline (SO8) Package (PbFree) 40 to +85°C2500 / Tape & Reel
SA5534AN 8Pin Plastic Dual InLine Package (PDIP8) 40 to +85°C50 Units / Rail
SA5534ANG 8Pin Plastic Dual InLine Package (PDIP8) (PbFree) 40 to +85°C50 Units / Rail
SA5534N 8Pin Plastic Dual InLine Package (PDIP8) 40 to +85°C50 Units / Rail
SA5534NG 8Pin Plastic Dual InLine Package (PDIP8) (PbFree) 40 to +85°C50 Units / Rail
SE5534AN 8Pin Plastic Dual InLine Package (PDIP8) 55 to +125°C50 Units / Rail
SE5534ANG 8Pin Plastic Dual InLine Package (PDIP8) (PbFree) 55 to +125°C50 Units / Rail
SE5534N 8Pin Plastic Dual InLine Package (PDIP8) 55 to +125°C50 Units / Rail
SE5534NG 8Pin Plastic Dual InLine Package (PDIP8) (PbFree) 55 to +125°C50 Units / Rail
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
NE5534, SA5534, SE5534, NE5534A, SA5534A, SE5534A
http://onsemi.com
9
PACKAGE DIMENSIONS
SOIC8 NB
CASE 75107
ISSUE AK
1.52
0.060
7.0
0.275
0.6
0.024
1.270
0.050
4.0
0.155
ǒmm
inchesǓ
SCALE 6:1
*For additional information on our PbFree strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
SEATING
PLANE
1
4
58
N
J
X 45_
K
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 75101 THRU 75106 ARE OBSOLETE. NEW
STANDARD IS 75107.
A
BS
D
H
C
0.10 (0.004)
DIM
A
MIN MAX MIN MAX
INCHES
4.80 5.00 0.189 0.197
MILLIMETERS
B3.80 4.00 0.150 0.157
C1.35 1.75 0.053 0.069
D0.33 0.51 0.013 0.020
G1.27 BSC 0.050 BSC
H0.10 0.25 0.004 0.010
J0.19 0.25 0.007 0.010
K0.40 1.27 0.016 0.050
M0 8 0 8
N0.25 0.50 0.010 0.020
S5.80 6.20 0.228 0.244
X
Y
G
M
Y
M
0.25 (0.010)
Z
Y
M
0.25 (0.010) ZSXS
M
____
NE5534, SA5534, SE5534, NE5534A, SA5534A, SE5534A
http://onsemi.com
10
PACKAGE DIMENSIONS
PDIP8
N SUFFIX
CASE 62605
ISSUE M
14
58
F
NOTE 5
D
e
b
L
A1
A
E3
E
A
TOP VIEW
CSEATING
PLANE
0.010 CA
SIDE VIEW
END VIEW
END VIEW
NOTE 3
DIM MIN NOM MAX
INCHES
A−−−− −−−− 0.210
A1 0.015 −−−− −−−−
b0.014 0.018 0.022
C0.008 0.010 0.014
D0.355 0.365 0.400
D1 0.005 −−−− −−−−
e0.100 BSC
E0.300 0.310 0.325
L0.115 0.130 0.150
−−−− −−−− 5.33
0.38 −−−− −−−−
0.35 0.46 0.56
0.20 0.25 0.36
9.02 9.27 10.02
0.13 −−−− −−−−
2.54 BSC
7.62 7.87 8.26
2.92 3.30 3.81
MIN NOM MAX
MILLIMETERS
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. DIMENSION E IS MEASURED WITH THE LEADS RE-
STRAINED PARALLEL AT WIDTH E2.
4. DIMENSION E1 DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
E1 0.240 0.250 0.280 6.10 6.35 7.11
E2
E3 −−−− −−−− 0.430 −−−− −−−− 10.92
0.300 BSC 7.62 BSC
E1
D1
M
8X
e/2
E2
c
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/PatentMarking.pdf . SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products
for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including
without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different
applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical
experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components
in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product
could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall
indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney
fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was
negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws
and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 8002829855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81358171050
NE5534/D
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 3036752175 or 8003443860 Toll Free USA/Canada
Fax: 3036752176 or 8003443867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your loc
a
Sales Representative