Series M Miniature Rockers
B62
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
General Specifications
Electrical Capacity (Resistive Load)
Power Level (silver): 6A @ 125V AC & 3A @ 250V AC
4A @ 30V DC for On-None-On; 3A @ 30V DC for all other circuits
Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Logic/Power Level (gold over silver): Combines silver & gold ratings
Note: Find additional explanation of dual rating & operating range in Supplement section.
Other Ratings
Contact Resistance: 10 milliohms maximum for silver; 20 milliohms maximum for gold
Insulation Resistance: 1,000 megohms minimum @ 500V DC
Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts and case for 1 minute minimum
Mechanical Life: 50,000 operations minimum
Electrical Life: 25,000 operations minimum for silver; 50,000 operations minimum for gold;
50,000 operations minimum for silver at 3A @ 125V AC
Angle of Throw: 25°
Materials & Finishes
Actuator Clip & Mounting Frame: Stainless Steel
Body Frame: Stainless steel
Case: Diallyl phthalate resin (UL94V–0)
Movable Contactor: Phosphor bronze with silver or gold plating
Movable Contacts: Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A)
Stationary Contacts: Silver with silver plating (code W); copper or brass with gold plating (code G);
or silver with gold plating (code A)
Terminals: Copper or brass with silver plating; or copper or brass with gold plating
Environmental Data
Operating Temp Range: –30°C through +85°C (–22°F through +185°F)
Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F)
Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Processing
Soldering: Wave Soldering (PC version) for Gold: See Profile A in Supplement section.
Manual Soldering for Gold: See Profile A in Supplement section.
Wave Soldering (PC version) for Silver: See Profile B in Supplement section.
Manual Soldering for Silver: See Profile B in Supplement section.
Note: Actuator must be in OFF (center) position while soldering.
Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
Flammability Standards: UL94V–0 for case
UL: File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” or “/CUL ” before first dash in part number to order UL recognized switch.
All models recognized at 6A @ 125V AC, 3A @ 250V AC or 0.4VA maximum @ 28V DC maximum.
CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch.
Add “/C” before first dash in part number to order CSA certified switch.
All models certified at 6A @ 125V AC or 3A @ 250V AC or 0.4VA maximum @ 28V maximum.
3/13/17
Series M
Miniature Rockers
B63
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
Distinctive Characteristics
Three methods of panel mounting: flat frame for flush with face or subpanel,
snap-in, and PCB.
High insulating barriers increase isolation of circuits in multipole devices
and provide added protection to contact points.
The molded diallyl phthalate case has a UL 94V-0
flammability rating.
Epoxy sealed terminals prevent entry of solder flux
and other contaminants.
Prominent external insulating barriers increase
insulation resistance and dielectric strength.
Bias guard prevents misalignment of contacts;
interlocking of actuator block with rocker and
internal guide does not allow transmission of
diagonal force on rocker to reach contact
mechanism.
Clinching of the frame to the case well above the base
and terminals provides 1,500V dielectric strength.
Actual Size
Flat Frame Mount Page B83
Bracket PC Mount Page B72
Snap-in Mount Page B64
Series M Snap-In Mount Miniature Rockers
B64
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
TYPICAL SWITCH ORDERING EXAMPLE
M20
Contact Materials & Ratings
WSilver; Rated
6A @ 125V AC & 3A @ 250V AC
GGold; Rated
0.4VA max @ 28V AC/DC max
A
Gold over Silver; Rated
6A @ 125V AC & 0.4VA max @
28V AC/DC max
Terminals
01 Solder Lug
02 Quick Connect
03 .250” (6.35mm)
Straight PC
05 .425” (10.8mm)
Wirewrap
06 .750” (19.05mm)
Wirewrap
07 .964” (24.5mm)
Wirewrap
08 1.062” (27.0mm)
Wirewrap
Poles
1SPDT
2DPDT
SP3T
Rockers & Paddles
F.450” (11.43mm) Wide Rocker
G.450” (11.43mm) Wide Paddle
S.453” (11.5mm) False
Illluminated Rocker in Black only
01 F
1 2
Circuits
2ON NONE ON
3ON OFF ON
5ON NONE (ON)
8(ON) OFF (ON)
9ON OFF (ON)
4ON ON ON
6(ON) ON (ON)
7ON ON (ON)
( ) = Momentary
3-ON circuits
*
*
*
*
Rocker & Paddle
Colors
ABlack
BWhite
CRed
EYellow
FGreen
GBlue
HGray
Snap-in Frame
SPDT
ON-NONE-ON Circuit
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
M2012TJW01-FC-1A
Red .450” (11.43mm)
Wide Rocker
Solder Lug Terminals
Silver Contacts with
6–Amp Rating
Mounting Frame
TJ Snap-in Frame
TJ WC
Black Bezel without LED
Series M
Snap-In Mount Miniature Rockers
B65
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
TYPICAL SWITCH ORDERING EXAMPLE
1 A
Snap-in Frame
SPDT ON-NONE-ON Circuit
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
M2012TJW01-FC-3A-CF
Solder Lug Terminals
Silver Contacts with
6–Amp Rating
Black Bezel with
2 Round LEDs
Top LED Red
Bottom LED Green
ABlack
BWhite
EYellow
FGreen
GBlue
HGray
1Bezel without LED
LED ColorsBezel ColorsOptional Bezels
2Bezel with 1 Round LED ABlack
ABlack
1 LED
CRed
FGreen
2 LEDs
Top LED Bottom LED
CRed CRed
EYellow EYellow
FGreen FGreen
Red .450” (11.43mm)
Wide Rocker
3Bezel with 2 Round LEDs
4Bezel with 2 Rectangular
LEDs
IMPORTANT:
Switches are supplied without UL, cULus & CSA marking unless specified.
UL, cULus & CSA recognized only when ordered with marking on the switch.
Specific models, ratings, & ordering instructions are noted on the General
Specifications page.
Series M Snap-In Mount Miniature Rockers
B66
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
For 3 Throw (3-On)
Connected Terminals & Schematic
Pole Model Down Center Up External Connection
SP
M2024
M2026
M2027
ON
(ON)
ON
ON
ON
ON
ON
(ON)
(ON)
2-3 5-6 2-3 5-4 2-1 5-4
External
connection
must be made
during field
installation.
The SP3T model utilizes a double pole
base.
(out)
63
2
14
5
(out)(out)
External
Conn
Common
(in)
Rocker Position
( ) = Momentary Connected Terminals Throw & Schematics
Pole Model
Down Center Up Down Center Up
SP
M2012
M2013
M2015
M2018
M2019
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
2-3 OPEN 2-1
SPDT
DP
M2022 ON NONE ON
2-3 5-6 OPEN 2-1 5-4
DPDT
M2023 ON OFF ON
M2025 ON NONE (ON)
M2028 (ON) OFF (ON)
M2029 ON OFF (ON)
Note: Terminal numbers are not
actually on the switch.
POLES & CIRCUITS
2 (COM)
1
3
4
613
25(COM)
MOUNTING FRAME
Snap-in Frame
TJ
Panel Thickness without Bezel: .039” ~ .126” (1.0mm ~ 3.2mm)
Panel Thickness with Bezel: .039” ~ .098” (1.0mm ~ 2.5mm)
CONTACT MATERIALS & RATINGS
Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC
Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum
Note: See Supplement section to find complete explanation of operating range.
Gold over Silver Power Level
or Logic Level
6A @ 125V AC
or 0.4VA maximum @ 28V AC/DC maximum
Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the
same application. See Supplement section to find complete explanation of dual rating and operating range.
A
W
G
Panel Cutout for
Single Pole
without Bezel
Panel Cutout for
Double Pole
without Bezel
(18.0)
.710
(12.2)
.480
25°
(4.3)
.170
(2.54) Dia
.100
(15.9)
.626
(12.5)
.492
(15.9)
.626
(13.1)
.516
1 (out) 4 (out) 6 (out)
2 (in)
3
5
External
Connection
2 (in)
5
Connection
1 (out) 4 (out) 6 (out)
2 (in)
3
5
External
Connection
Series M
Snap-In Mount Miniature Rockers
B67
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
TERMINALS
ROCKERS & PADDLES
01
03
05
08
07
06
Solder Lug 02 .062” (1.57mm) Wide
Quick Connect
.425” (10.8mm)
Wirewrap or Extended PC
.750” (19.05mm)
Wirewrap or Extended PC
.964” (24.5mm)
Wirewrap or Extended PC
1.062” (27.0mm)
Wirewrap or Extended PC
.250” (6.35mm)
Straight PC
If using as extended PC terminal, refer to
the above footprints.
Dimension A = terminal lengths as shown
beside the terminal codes
at the left.
Single Pole Double Pole
(6.35)
.250
Epoxy Seal
Thk = (0.8)
.031
(1.57)
.062
Epoxy Seal
(2.0)
.079 (2.0)
.079
(4.0)
.157
(1.1)
.043
Thk = (0.8)
.031
Epoxy Seal
(4.8)
.189
(6.35)
.250
(1.17)
.046
Thk = (0.8)
.031
Thk = (0.8)
.031
Epoxy Seal
A
(1.27)
.050
(4.7) Ty
p
.185
(4.8)
.189
(1.8) Dia Typ
.073
1
2
36
5
4
(4.7) Typ
.185
(1.8) Dia Ty
p
.073
1
2
3
AT4150
.450” (11.43mm)
Wide Rocker
F
Black
A
Cap Colors
Available: White
BRed
CYellow
EGreen
FBlue
G
Material: Polyamide
Finish: Matte
Colors Available:
A, B, C, E, F, G, H
Gray
H
AT4151
.450” (11.43mm)
Wide Paddle
G
Material: Polyamide
Finish: Matte
Colors Available:
A, B, C, E, F, G, H
AT466 .453” (11.5mm)
False Illuminated Rocker
S
Rocker False Illuminator
Material: Polycarbonate Acrylonitrile Butadiene Styrene
Finish: Glossy
Colors: Black White and Red
When a bezel is selected with AT466, glossy polycarbonate AT207 is supplied.
(6.3)
.248
(9.19)
.362 (11.43)
.450
(7.11)
.280
(1.8)
.071 (11.8)
.465
(11.8)
.465
(16.36)
.644
(11.43)
.450
(2.36)
.093
(1.8)
.071
(5.84) R
.230
(8.6)
.339 (11.3)
.445
(7.7)
.303
(1.8)
.071
(11.8)
.465
(11.5)
.453
Series M Snap-In Mount Miniature Rockers
B68
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
Yellow
E
OPTIONAL SNAP-IN BEZELS & BEZEL COLORS
AT2107 Bezel
1
Black
A
White
B
Green
F
Blue
G
Material: Polyamide
Finish: Matte
Gray
H
AT208 Bezel
for AT070 LED
2
Material:
Polycarbonate
Finish: Glossy
Contact factory
for matte finish.
AT212 Bezel
for AT617 LED
3
Material:
Polycarbonate
Finish:
Semi-glossy
AT213 Bezel
for AT618 LED
4
Material:
Polycarbonate
Finish:
Semi-glossy
Bezel Assembly
45°
Tab
Tab
1. Pry out tab on bezel to
a 45° angle.
2. Insert switch frame under
tab and snap on bezel.
3. Push tab back into place. 4. Snap assembled bezel
and switch into panel.
(11.8)
.465
(21.5)
.846
(12.0)
.472
(15.6)
.614
(2.2)
.087
(30.2)
1.19
(19.0)
.748
(12.0)
.472
(11.8)
.465
(13.5)
.531
(15.6)
.614
(5.4) Dia
.213
(2.2)
.087
(21.5) Sq
.846
(11.8)
.465
(10.0)
.394
(12.0)
.472
(2.2)
.087
(7.8)
.307
(3.0) Dia Typ
.118
(8.0)
.315
(11.8)
.465
(10.0)
.394 (12.0)
.472
(2.2)
.087
(7.8)
.307
(21.5) Sq
.846
(5.0) Typ
.197
(8.0)
.315
(2.0) Typ
.079
Black
A
Black
A
Black
A
LED colors & specifications
on next page.
LED colors &
specifications
on next page.
LED colors &
specifications
on next page.
(15.9)
.626
(15.9)
.626
A
Single Pole Double Pole
A(12.5)mm
.492”
(13.1)mm
.516”
Single Pole Double Pole
A(12.5)mm
.492”
(13.1)mm
.516”
B(6.25)mm
.246”
(6.55)mm
.258”
(15.9)
.626
(13.8)
.543
(8.8) Dia
.346
B
A
(15.9)
.626
A
(15.9)
.626
A
Single Pole Double Pole
A(18.4)mm
.724”
(18.7)mm
.736”
Single Pole Double Pole
A(18.4)mm
.724”
(18.7)mm
.736”
Series M
Snap-In Mount Miniature Rockers
B69
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
Top LED
Bottom LED
Circuit Mark This Side
Top LED
Bottom LED
Circuit Mark This Side
Circuit Mark This Side
AT070 AT617 AT618
Color Red Green Red Yellow Green Red Yellow Green
Maximum Forward Current IFM 25mA 50mA 30mA 30mA 25mA 25mA 30mA 25mA
Typical Forward Current IF20mA 30mA 20mA 20mA 20mA 20mA 20mA 20mA
Forward Voltage VF2.8V 2.1V 2.0V 2.1V 2.25V 2.25V 2.1V 2.2V
Maximum Reverse Voltage VRM 4V 5V 5V 5V 5V 5V 5V 5V
Current Reduction Rate
Above 25°C ∆IF
0.33
mA/°C
0.40
mA/°C
0.40
mA/°C
0.40
mA/°C
0.33
mA/°C
0.33
mA/°C
0.40
mA/°C
0.33
mA/°C
Ambient Temperature Range
(when used with a bezel) –10° ~ +70°C –15° ~ +70°C –25° ~ +70°C
LED COLORS & SPECIFICATIONS
Bezel Orientation on Switch
AT070 LED
For Bezel AT208
with 1 LED
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is independent of switch operation. LED is colored in OFF state.
If the source voltage is greater than the rated voltage of the LED, a ballast resistor must be connected in series with the lamp.
The ballast resistor calculation and more lamp detail are shown in the Supplement section.
(+) (-)
AT617 LED
For Bezel AT212
with 2 Round LEDs
AT618 LED
For Bezel AT213
with 2 Rectangular LEDs
Note: Lead lengths may differ from manufacturing lot to lot. The longer lead is the anode (+).
FE
C
FECC F
(5.08) Dia
.200
(7.7)
.303
(+)
(-)
(5.0)
.197
(3.0) Dia
.118
(+)
(-)
(7.0)
.276
(5.0)
.197
(+)
(-)
LEGENDS
NKK Switches can provide custom legends for caps. Contact factory for more information.
Suggested Printable Area for Cap
AT4150
Recommended Print Method:
Pad Print
Epoxy based ink is recommended.
OFF
ON
(9.91)
.390
(3.36) Ty
p
.132
(11.43)
.450
(0.76) Typ
.030
(0.76)
Typ
.030
(0.38) Typ
.015
(4.5) Typ
.177
Shaded areas are printable areas.
Series M Snap-In Mount Miniature Rockers
B70
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
TYPICAL SWITCH DIMENSIONS
Snap-in Frame • Solder Lug Single Pole
M2012TJW01-FC
Snap-in Frame • Solder Lug Double Pole
M2022TJW01-FC
Snap-in Frame • Solder Lug Single Pole
Snap-in Frame • Solder Lug Double Pole
M2012TJW01-GC
M2022TJW01-GC
(18.0)
.709
(11.43)
.450
(12.2)
.480
25°
(2.8)
.110
(4.9)
.194
(0.5)
.020
(3.3)
.130
(7.1)
.279
(9.4)
.371
(4.5)
.177
(0.5)
.020
(0.8) Typ
.031
(4.7) Typ
.185
(1.1) x (2.0) Typ
.043 x .079
Circuit Mark
This Side
3
2
1
(13.0)
.512
(2.0) Typ
.079
(7.9)
.311
(18.0)
.709
(11.43)
.450
(12.2)
.480
(2.8)
.110
(0.5)
.020
(7.1)
.279
(9.4)
.371
(4.5)
.177
(0.5)
.020
(0.8) Typ
.031
(4.7) Typ
.185
(1.1) x (2.0) Ty
p
.043 x .079
Circuit Mark
This Side
25°
(2.36)
.093 (3.18)
.125
(13.7)
.539
3
2
1
(13.0)
.512
(2.0) Typ
.079
(7.9)
.311
(18.0)
.709
(11.43)
.450
(12.2)
.480
25°
(2.8)
.110
(4.9)
.194
(0.5)
.020
(3.3)
.130
(7.1)
.279
(9.4)
.371
(4.5)
.177
(0.5)
.020
(0.8) Typ
.031
(4.7) Typ
.185
(1.1) x (2.0) Typ
.043 x .079
Circuit Mark
This Side
(13.0)
.512
63
2
5
41
(4.8)
.189
(2.0) Ty
p
.079
(12.7)
.500
(18.0)
.709
(11.43)
.450
(12.2)
.480
(2.8)
.110
(0.5)
.020
(7.1)
.279
(9.4)
.371
(4.5)
.177
(0.5)
.020
(0.8) Typ
.031
(4.7) Typ
.185
(1.1) x (2.0) Ty
p
.043 x .079
Circuit Mark
This Side
25°
(2.36)
.093
(3.18)
.125
(13.7)
.539
63
2
5
41
(13.0)
.512
(4.8)
.189
(2.0) Ty
p
.079
(12.7)
.500
Series M
Snap-In Mount Miniature Rockers
B71
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
TYPICAL SWITCH DIMENSIONS
Single & Double Pole Snap-in Frame • AT2107 Bezel • Solder Lug
M2012TJW01-FC-1A
Double Pole Snap-in Frame • AT208 Bezel • Solder Lug
M2022TJW01-FC-2A-C
Single Pole Snap-in Frame • AT212 Bezel • Solder Lug
Double Pole Snap-in Frame • AT213 Bezel • Solder Lug
M2012TJW01-FC-3A-CF
M2022TJW01-FC-4A-CF
(15.6)
.614
(11.8)
.465
(11.43)
.450
(12.0)
.472
(21.5)
.846
(2.2)
.087
(6.4)
.252
(9.4)
.371
(4.5)
.177
(4.01)
.158
(4.3)
.169
(0.5)
.020
25°
(5.6)
.221
(1.1) x (2.0) Typ
.043 x .079
(4.7) Typ
.185
(0.8) Typ
.031
Circuit Mark
This Side
(13.0)
.512
3
2
1
(7.9)
.311
(2.0)
.079
(14.0)
.551
(5.08) Dia
.200
(30.2)
1.190
(12.0)
.472
(11.43)
.450
(11.8)
.465
(15.6)
.614
(13.5)
.531
(19.0)
.748 Circuit Mark
This Side
25°
(4.9)
.193
(1.1) x (2.0) Typ
.043 x .079
(0.8) Typ
.031
(4.5)
.177
(0.5)
.020
(2.2)
.087
(4.3)
.169
(4.01)
.158
(6.4)
.252
(9.4)
.371
(0.61) Sq
.024
(15.3) Min
.602
(4.7) Typ
.185
(2.5)
.098
63
52
41
(14.0)
.551
(13.0)
.512
(2.0) Typ
.079
(12.7)
.500
(4.8)
.189
(10.0)
.394
(7.8)
.307
(12.0)
.472
(8.0)
.315
(11.43)
.450
(11.8)
.465
(3.0) Dia
Typ
.118
(21.5) Sq
.846
Circuit Mark
This Side
25°
(5.6)
.221
(1.1) x (2.0) Typ
.043 x .079
(0.8) Typ
.031
(4.5)
.177
(0.5)
.020
(2.2)
.087
(4.3)
.169
(4.01)
.158
(6.4)
.252
(9.4)
.371
(4.7) Typ
.185
3
2
1
(7.9)
.311
(2.0)
.079
(14.0)
.551
(13.0)
.512
(10.0)
.394 (7.8)
.307
(12.0)
.472
(8.0)
.315
(2.0)
.079
(11.43)
.450
(11.8)
.465
(21.5) Sq
.846
(5.0)
Typ
.197
Circuit Mark
This Side
25°
(5.6)
.221
(1.1) x (2.0) Typ
.043 x .079
(0.8) Typ
.031
(4.5)
.177
(0.5)
.020
(2.2)
.087
(4.3)
.169
(4.01)
.158
(6.4)
.252
(9.4)
.371
(4.7) Ty
p
.185
3
2
1
(12.7)
.500
(2.0) Typ
.079
(14.0)
.551
(13.0)
.512
6
5
4
(4.8)
.189
(4.8)
.189
(12.7)
.500
(2.0) Typ
.079
63
2
5
41
(13.0)
.512
(14.0)
.551
Series M Bracket PC Mount Miniature Rockers
B72
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
TX
TYPICAL SWITCH ORDERING EXAMPLE
M20
Contact Materials & Ratings
WSilver; Rated
6A @ 125V AC & 3A @ 250V AC
GGold; Rated
0.4VA max @ 28V AC/DC max
A
Gold over Silver; Rated
6A @ 125V AC & 0.4VA max @
28V AC/DC max
G1 3
Circuits
2ON NONE ON
3ON OFF ON
5ON NONE (ON)
8(ON) OFF (ON)
9ON OFF (ON)
4ON ON ON
6(ON) ON (ON)
7ON ON (ON)
( ) = Momentary
3-ON circuits
*
*
*
*
Mounting Frames
TX Narrow Frame
for Small Actuator
TZ Wide Frame
for Large Actuator
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
M2013TXG41-DC
Poles
1SPDT
2DPDT
SP3T
3
3PDT (used only
with terminal codes
30 & 41 & frame
code TX)
4
4PDT
DP3T
(used only with
terminal code 41 &
frame code TX)
SPDT
ON-OFF-ON Circuit
TX Frame with .365” (9.27mm)
Wide Red Rocker
Gold Contacts with
0.4VA Rating
.150” (3.81mm)
Vertical PC Terminals with Support
Series M
Bracket PC Mount Miniature Rockers
B73
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
TYPICAL SWITCH ORDERING EXAMPLE
DPDT
ON-NONE-ON Circuit
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
M2022TZG23-JC
TZ Frame with .595” (15.11mm)
Wide Red Rocker
Terminals For
TX & TZ Frames
Straight PC with Bracket
(1-2 Pole only)
13 .250” (6.35mm) Straight PC with
.465” (11.8mm) Bracket
15 .425” (10.8mm) Straight PC with
.630” (16.0mm) Bracket
17 .964” (24.5mm) Straight PC with
1.150” (29.2mm) Bracket
Straight PC with Reinforced Bracket
(1-2 Pole only)
23 .250” (6.35mm) Straight PC with
.465” (11.8mm) Bracket
25 .425” (10.8mm) Straight PC with
.630” (16.0mm) Bracket
26 .750” (19.05mm) Straight PC with
.953” (24.2mm) Bracket
Gold Contacts with 0.4VA Rating
.250” (6.35mm) Straight PC Terminals
with Reinforced Bracket
Rockers
& Paddles
Small Actuators
(TX Frame)
D.365” (9.27mm)
Wide Rocker
E.365” (9.27mm)
Wide Paddle
F.450” (11.43mm)
Wide Rocker
G.450” (11.43mm)
Wide Paddle
Large Actuators
(TZ Frame)
J.595” (15.11mm)
Wide Rocker
H.595” (15.11mm)
Wide Paddle
Rocker & Paddle
Colors
ABlack
BWhite
CRed
EYellow
FGreen
GBlue
HGray
41 D C
Terminals For
TX Frame Only
Right Angle PC with Support
(1-3 Pole only)
30 .150” (3.81mm) Right Angle PC
Vertical PC with Support
(1-4 Pole)
41 .150” (3.81mm) Vertical PC
IMPORTANT:
Switches are supplied without UL & CSA marking unless specified.
UL & CSA recognized only when ordered with marking on the switch.
Specific models, ratings and ordering instructions are noted on the
General Specifications page.
Series M Bracket PC Mount Miniature Rockers
B74
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
Rocker Position
( ) = Momentary Connected Terminals Throw & Schematics
Pole Model
Down Center Up Down Center Up
SP
M2012
M2013
*M2015
M2018
*M2019
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
2-3 OPEN 2-1
SPDT
DP
M2022
M2023
*M2025
M2028
*M2029
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
2-3 5-6 OPEN 2-1 5-4
DPDT
3P
M2022
M2023
*M2025
M2028
*M2029
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
2-3 5-6
8-9 OPEN 2-1 5-4
8-7
3PDT
4P
M2042
M2043
*M2045
M2048
*M2049
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
2-3 5-6
8-9 11-12 OPEN 2-1 5-4
8-7 11-10
4PDT
Note: Terminal numbers are not actually
on the switch.
* Reverse circuits available for vertical
mount SP & DP upon request.
POLES & CIRCUITS
11
10
127
9
4
6
1
3
258
(COM)
2 5 (COM) 8
31
64
97
2 (COM)
1
3
4613
25(COM)
For 3 Throw (3-On)
Connected Terminals & Schematics
Pole Model Down Center Up Down Center Up
SP
M2024
M2026
M2027
ON
(ON)
ON
ON
ON
ON
ON
(ON)
(ON)
DP
M2044
M2046
M2047
ON
(ON)
ON
ON
ON
ON
ON
(ON)
(ON)
2-3 5-6 2-3 5-4 2-1 5-4
2-3 5-6 2-3 5-4 2-1 5-4
8-9 11-12 8-9 11-10 8-7 11-10
External connection must be
made during field installation.
The SP3T model utilizes a
double pole base.
External connection must be
made during field installation.
The DP3T model utilizes a
four pole base.
(out)(out)
(out) (out)
(out)
(out)
External
Conn
Common
(in)
Common
(in)
1
2
4710
12 96 3
5811
(out)
63
2
14
5
(out)(out)
External
Conn
Common
(in)
1 (out) 4 (out) 6 (out)
2 (in)
3
5
External
Connection
1 (out) 4 (out) 6 (out)
2 (in)
3
5
External
Connection
1 (out) 4 (out) 6 (out)
2 (in)
3
5
External
Connection
1 (out)
4 (out) 6 (out) 7 (out) 10 (out)
12 (out)
8 (in)2 (in)
39
51
1
External
Connection External
Connection
1 (out)
4 (out) 6 (out) 7 (out) 10 (out)
12 (out)
8 (in)2 (in)
39
51
1
External
Connection
External
Connection
1 (out)
4 (out) 6 (out) 7 (out) 10 (out)
12 (out)
8 (in)2 (in)
39
51
1
External
Connection External
Connection
Series M
Bracket PC Mount Miniature Rockers
B75
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
MOUNTING FRAMES
Narrow Mounting Frame for Small Actuators
with Straight PC Terminals (codes 13, 15, 17, 23, 25, & 26)
or with Angle PC Terminals (codes 30 & 41)
TX
Small Actuators & Panel Cutouts for TX Frame (actuator details on the following pages)
CONTACT MATERIALS & RATINGS
Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC
Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum
Note: See Supplement section to find complete explanation of operating range.
Gold over Silver Power Level
or Logic Level
6A @ 125V AC
or 0.4VA maximum @ 28V AC/DC maximum
Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the
same application. See Supplement section to find complete explanation of dual rating and operating range.
A
W
G
Wide Mounting Frame
for Large Actuators
with Straight PC Terminals
(codes 13, 15, 17, 23, 25, & 26)
TZ
Straight PC Mounting Right Angle PC Mounting Vertical PC Mounting
AT4148 AT4149 AT4150 AT4151
Large Actuators & Panel Cutouts for TZ Frame
(actuator details on the following pages)
(5.08)
.200
(0.4)
Typ
.016
(8.0)
.315
(1.4) Ty
p
.055
(5.08)
.200 25°
(2.54) Dia
.100
(4.37)
.172
25°
(2.54) Dia
.100
(3.5)
.138
(6.0)
.235
(1.27)
.050
(2.75)
.108
25°
(2.54) Dia
.100
25°
(3.5)
.138
(2.54) Dia
.100
AT4156 AT4157
(16.0)
.630
(28.5)
1.122
Direction of Actuation
(12.7)
.500
(12.4)
.490
Direction of Actuation
(10.1)
.398
(17.8)
.701
Direction of Actuation
Series M Bracket PC Mount Miniature Rockers
B76
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
TERMINALS
ROCKERS & PADDLES FOR TX MOUNTING FRAMES
AT4148 .365” (9.27mm)
Wide Rocker
D
Black
A
Cap Colors
Available: White
BRed
CYellow
EGreen
FBlue
G
Material: Polyamide
Finish: Matte
Gray
H
AT4149 .365” (9.27mm)
Wide Paddle
E
Material: Polyamide
Finish: Matte
13
.250” (6.35mm)
Terminal with
.465” (11.8mm)
Bracket
PCB footprints are on the following Typical Switch Dimension pages.
15 17 23 25 26
.750” (19.05mm)
Terminal with
.953” (24.2mm)
Bracket
.425” (10.8mm)
Terminal with
.630” (16.0mm)
Bracket
.250” (6.35mm)
Terminal with
.465” (11.8mm)
Bracket
.964” (24.5mm)
Terminal with
1.150” (29.2mm)
Bracket
.425” (10.8mm)
Terminal with
.630” (16.0mm)
Bracket
For TX and TZ 1-2 Pole
Straight PC Mount with Bracket
AT4150 .450” (11.43mm)
Wide Rocker
F
Material: Polyamide
Finish: Matte
AT4151 .450” (11.43mm)
Wide Paddle
G
Material: Polyamide
Finish: Matte
For TX and TZ 1-2 Pole
Straight PC Mount with Reinforced Bracket
For TX 1-3 Pole Right Angle PC Mount For TX 1-4 Pole Vertical PC Mount
.150” (3.81mm)
Right Angle PC
30 .150” (3.81mm)
Vertical PC
41
(2.36)
.093
(3.18)
.125
(5.84) R
.230
(16.36)
.644
(3.5)
.138
(11.8)
.465
(11.43)
.450
(6.3)
.248
(8.1)
.319
(11.8)
.465
(9.19)
.362
(3.5)
.138
(7.7)
.303
(11.43)
.450
(2.13)
.084
(3.96)
.156
(8.43) R
.332
(3.5)
.138
(18.8)
.740
(16.8)
.661
(9.27)
.365
(7.9)
.311
(8.8)
.346
(6.15)
.242
(3.5)
.138
(13.49)
.531
(16.87)
.664
(9.27)
.365
Series M
Bracket PC Mount Miniature Rockers
B77
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
ROCKERS & PADDLES FOR TZ MOUNTING FRAMES
OPTIONAL SNAP-IN PANEL FRAMES
Black
A
Cap Colors
Available: White
BRed
CYellow
EGreen
FBlue
GGray
H
AT4156 .595” (15.11mm)
Wide Rocker
JAT4157 .595” (15.11mm)
Wide Paddle
H
(6.68)
.263
(15.62)
.615
(17.9)
.705
(25.04)
.986
(9.9)
.390
(2.3
)
.090
(6.68)
.263
(19.43)
.765
(15.62)
.615
(2.3
)
.090
(12.0)
.472
(12.8)
.504
(15.11)
.595
(11.0)
.433
(23.01)
.906
(6.5)
.256
(8.4)
.331
(3.5)
.138
(26.78)
1.054
(14.33)
.564
(15.11)
.595
(29.82)
1.174
(26.8)
1.055
(2.36)
.093
(4.75)
.187
(13.5) R
.531
(7.3)
.287
(3.5)
.138
Material: Polyamide
Finish: Matte
Material: Polyamide
Finish: Matte
AT064-1
Accommodates .047” ~ .090”
(1.2 ~ 2.3mm) panel thickness
Material: Polyamide
Finish: Matte
Color: Black
Mounted separately from switches
Cutout Tolerances:
Dimension A:
.797” ~ .803” (20.24 ~ 20.4mm)
Dimension B:
.495” ~ .505” (12.57 ~ 12.83mm)
Used with AT4148 Rocker and AT4149 Paddle
Used with AT4150 Rocker and AT4151 Paddle
AT064-2
Accommodates .062” ~ .125”
(1.57 ~ 3.18mm) panel thickness
AT065-2
Accommodates .062” ~ .125”
(1.57 ~ 3.18mm) panel thickness
AT065-1
Accommodates .047” ~ .090”
(1.2 ~ 2.3mm) panel thickness
Material: Polyamide
Finish: Matte
Color: Black
Mounted separately from switches
Cutout Tolerances:
Dimension A:
.595” ~ .605” (15.11 ~ 15.37mm)
Dimension B:
.495” ~ .500” (12.57 ~ 12.7mm)
AT064–1 Enlarged Detail
AT065–1 Enlarged Detail AT065–2 Enlarged Detail
A
B
A
B
Series M Bracket PC Mount Miniature Rockers
B78
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
(8.0)
.315
(1.17)
Typ
.046
(1.17)
Typ
.046
(12.7)
.500
(4.8)
.189
(3.2) Typ
.126
(4.8) Typ
.189
BRACKET
LENGTH
(1.17)
Typ
.046
(1.17)
Typ
.046
(9.1)
.358
BRACKET
LENGTH
(4.8)
.189
(4.8) Ty
p
.189
(6.35) Typ
.250
(12.7)
.500
TYPICAL SWITCH DIMENSIONS
Straight PC • Bracket
Straight PC • Reinforced Bracket
M2012TXG13-DC
M2012TXG23-DC
Single
Pole
Single
Pole
Double
Pole
Double
Pole
Terminal
Code:
Terminal
Length:
Bracket
Length:
13 .250” (6.35mm) .465” (11.8mm)
15 .425” (10.8mm) .630” (16.0mm)
17 .964” (24.5mm) 1.150” (29.2mm)
Terminal
Code:
Terminal
Length:
Bracket
Length:
23 .250” (6.35mm) .465” (11.8mm)
25 .425” (10.8mm) .630” (16.0mm)
26 .750” (19.05mm) .953” (24.2mm)
2
14
5
63
(1.6) Typ
.063
(2.4) Typ
.095
(7.9) Typ
.311
(4.7) Typ
.185
(1.8) Dia
Typ
.073
(1.5) Dia
Typ
.059
C
L
2
1
3
(1.6) Typ
.063
(7.9) Typ
.311
(4.7) Typ
.185
(1.8) Dia Typ
.073
(1.5) Dia
Typ
.059
(4.7) Typ
.185
2
1
3
(3.18) Typ
.125
(9.53) Typ
.375
(1.8) Dia
Typ
.073
(1.5) Dia
Typ
.059
(4.7) Typ
.185
(2.4) Typ
.095
2
14
5
6
3
(3.18) Typ
.125
(9.53) Typ
.375
(1.8) Dia
Typ
.073
(1.5) Dia
Typ
.059
C
L
25°
(6.15)
.242
(3.5)
.138
TERMINAL
LENGTH
(0.5) Typ
.020
(0.8) Typ
.031
(4.7) Typ
.185 (15.8)
.622
(8.8)
.346
123
Circuit Mar
k
This Side
123
(8.8)
.346
25°
(6.15)
.242
(3.5)
.138
TERMINAL
LENGTH
(0.5) Typ
.020
(0.8) Typ
.031
(4.7) Typ
.185 (19.05)
.750
Circuit Mar
k
This Side
Series M
Bracket PC Mount Miniature Rockers
B79
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
TYPICAL SWITCH DIMENSIONS
Single Pole .150” (3.81mm) Right Angle PC
M2012TXG30-DC
Double Pole .150” (3.81mm) Right Angle PC
M2022TXG30-DC
Three Pole .150” (3.81mm) Right Angle PC
M2032TXG30-DC
(5.08)
.200
(1.4) Typ
.055
(2.85)
.112
(6.4)
.252
Shown in
Down Position
(9.27)
.365
(1.27) Ty
p
.050
(0.4) Typ
.016
(3.81)
.150
Pivot
(6.15)
.242
(4.0)
.157
(8.8)
.346
(12.7)
.500
6
5
4
123
(12.7)
.500
(4.3)
.169
(0.8) Typ
.031
(4.7) Typ
.185
(13.0)
.512
(1.8) Dia Typ
.073
21
3
(4.7) Typ
.185
(2.54) Typ
.100
(12.7)
.500
54
6
(3.81)
.150
(5.41)
.213
(2.85)
.112
(5.08)
.200
(1.4) Typ
.055
Shown in
Down Position
Pivot
(1.27)
.050
(12.7)
.500
(8.8)
.346
(6.15)
.242
(0.4)
.016 (5.5)
.217
(4.0)
.157
(9.27)
.365
123
(13.0)
.512
(7.9)
.311
(4.3)
.169
(0.8) Typ
.031
(4.7) Ty
p
.185
(4.7) Typ
.185
(1.8) Dia Ty
p
.073
123
(12.7)
.500
(2.54) Typ
.100
(8.8)
.346
(2.85)
.112
(5.08)
.200
(1.4) Typ
.055
Shown in
Down Position
Pivot
(1.27) Ty
p
.050
(3.81) Typ
.150
(14.35)
.565
(4.5)
.177
(0.4)
.016
(6.15)
.242
(8.8)
.346
(9.27)
.365
789
654
123
(4.3)
.169
(17.5)
.689
(13.0)
.512
(0.8) Typ
.031
(4.7) Typ
.185
21
3
(4.7) Typ
.185
(2.54) Typ
.100
(14.35)
.565
(1.8) Dia Typ
.073
54
6
87
9
(3.81) Ty
p
.150
Series M Bracket PC Mount Miniature Rockers
B80
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
TYPICAL SWITCH DIMENSIONS
.150” (3.81mm) Vertical PC Single Pole
M2012TXG41-DC
.150” (3.81mm) Vertical PC Three Pole
M2032TXG41-DC
.150” (3.81mm) Vertical PC Four Pole
M2042TXG41-DC
M2022TXG41-DC
.150” (3.81mm) Vertical PC Double Pole
(9.27)
.365
(5.08)
.200
(0.4)
Typ
.016
25°
(9.1)
.360
(2.74)
.108
(6.15)
.242
(5.97)
.235
(1.27)
.050
(12.7)
.500
(3.18)
.125
(3.5)
.138
(8.8)
.346
(0.8) Typ
.031
(3.81) Typ
.150
Shown in
Down Position
(7.9)
.311
(1.27)
.050
(13.0)
.512
(9.27)
.365
(5.08)
.200
(0.4)
Typ
.016
25°
(9.1)
.360
(2.74)
.108
(6.15)
.242
(5.97)
.235
(1.27)
.050
(12.7)
.500
(3.18)
.125
(3.5)
.138
(8.8)
.346
(0.8) Typ
.031
(3.81) Typ
.150
Shown in
Down Position
6
5
41
2
3
(13.0)
.512
(12.7)
.500
(4.8)
.189
(1.27) Ty
p
.050
(9.27)
.365
(5.08)
.200
(0.4)
Typ
.016
(2.74)
.108
(6.15)
.242
(5.97)
.235
(1.27)
.050
(14.35)
.565
(3.81) Typ
.150
(3.18)
.125
(0.8) Typ
.031
(3.5)
.138
(8.8)
.346
(9.1)
.360
25°
Shown in
Down Position
6
5
41
2
3
9
8
7
(13.0)
.512
(17.5)
.689
(1.27) Ty
p
.050
(4.8) Typ
.189
6
5
41
2
3
9
8
7
10
11
12
(13.0)
.512
(1.27) Ty
p
.050
(4.8) Typ
.189
(22.3)
.878
(2.74)
.108
(6.15)
.242
(5.97)
.235
(1.27)
.050
(14.35)
.565
(3.81) Typ
.150
(3.18)
.125
(0.8) Typ
.031
(3.5)
.138
(8.8)
.346
(9.1)
.360
25°
Shown in
Down Position
(9.27)
.365
(5.08)
.200
(0.4) Typ
.016
(1.8) Dia Typ
.073
2
1
3
(4.8) Typ
.189
(2.54) Typ
.100
(14.35)
.565
5
4
6
(3.81) Typ
.150
9
8
710
11
12
(1.8) Dia Typ
.073
2
1
3
(4.8) Typ
.189
(2.54) Typ
.100
(14.35)
.565
5
4
6
(3.81) Ty
p
.150
9
8
7
(2.4) Typ
.094
(1.8) Dia Typ
.073
1
2
3
(12.7)
.500
(2.54) Typ
.100
(3.81) Ty
p
.150
4
5
6
(12.7)
.500
(1.8) Dia Typ
.073
2
1
3
(2.54) Typ
.100
(3.81) Typ
.150
Series M
Bracket PC Mount Miniature Rockers
B81
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
(8.0)
.315
(1.17)
Typ
.046
(1.17)
Typ
.046
BRACKET
LENGTH
(4.8) Typ
.189
(4.8)
.189
(3.2) Typ
.126
(12.7)
.500
(9.1)
.358
(1.17)
Typ
.046
(1.17)
Typ
.046
BRACKET
LENGTH
(4.8) Ty
p
.189
(6.35) Typ
.250
(4.8)
.189
(12.7)
.500
TYPICAL SWITCH DIMENSIONS
Straight PC • Bracket
Straight PC • Reinforced Bracket
M2012TZG13-JC
M2012TZG23-JC
Single
Pole
Single
Pole
Double
Pole
Double
Pole
Terminal
Code:
Terminal
Length:
Bracket
Length:
13 .250” (6.35mm) .465” (11.8mm)
15 .425” (10.8mm) .630” (16.0mm)
17 .964” (24.5mm) 1.150” (29.2mm)
Terminal
Code:
Terminal
Length:
Bracket
Length:
23 .250” (6.35mm) .465” (11.8mm)
25 .425” (10.8mm) .630” (16.0mm)
26 .750” (19.05mm) .953” (24.2mm)
2
14
5
63
(1.6) Typ
.063
(2.4) Typ
.095
(7.9) Typ
.311
(4.7) Typ
.185
(1.8) Dia
Typ
.073
(1.5) Dia
Typ
.059
C
L
2
1
3
(1.6) Typ
.063
(7.9) Typ
.311
(4.7) Typ
.185
(1.8) Dia
Typ
.073
(1.5) Dia
Typ
.059
(4.7) Typ
.185
2
1
3
(3.18) Typ
.125
(9.53) Typ
.375
(1.8) Dia
Typ
.073
(1.5) Dia
Typ
.059
(4.7) Typ
.185
(2.4) Typ
.095
2
14
5
6
3
(3.18) Typ
.125
(9.53) Typ
.375
(1.8) Dia
Typ
.073
(1.5) Dia
Typ
.059
C
L
25°
123
TERMINAL
LENGTH
(3.5)
.138
(15.8)
.622
(0.6) Typ
.024
(0.8) Typ
.031
(4.7) Typ
.185
(11.0)
.433
(6.6)
.260
Circuit Mar
k
This Side
(19.05)
.750
123
TERMINAL
LENGTH
(3.5)
.138
(0.5) Typ
.020
(0.8) Typ
.031
(4.7) Typ
.185
(6.6)
.260
25°
(11.0)
.433
Circuit Mar
k
This Side
Series M Bracket PC Mount Miniature Rockers
B82
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
LEGENDS
NKK Switches can provide custom legends for caps. Contact factory for more information.
Suggested Printable Area for Cap
AT4148 AT4150
Shaded areas are printable areas.
Recommended Print Method:
Pad Print
Epoxy based ink is recommended.
OFF
ON
OFF
ON
AT4156
OFF
ON
(9.27)
.365
(7.75)
.305
(5.76) Ty
p
.227
(6.9)
Typ
.272
(0.76)
Typ
.030
(0.76) Typ
.030
(0.38) Typ
.015
(9.91)
.390
(3.36) Ty
p
.132
(11.43)
.450
(0.76) Typ
.030
(0.76)
Typ
.030
(0.38) Typ
.015
(4.5)
Typ
.177
(15.11)
.595
(13.59)
.535
(11.18)
Typ
.440
(10.03) Ty
p
.395
(0.76) Typ
.030
(0.76) Typ
.030
(0.38) Typ
.015
Series M
Flat Frame Mount Miniature Rockers
B83
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
TN
TYPICAL SWITCH ORDERING EXAMPLE
M20
SPDT
ON-NONE-ON Circuit
Contact Materials
& Ratings
WSilver; Rated 6A @ 125V
AC & 3A @ 250V AC
GGold; Rated 0.4VA max @
28V AC/DC max
A
Gold over Silver; Rated
6A @ 125V AC & 0.4VA
max @ 28V AC/DC max
Red .365” (9.27mm)
Wide Rocker
Terminals
01 Solder Lug
03 .250” (6.35mm)
Straight PC
.272” (6.9mm) Wide
Flat Frame
Silver Contacts
with 6-Amp Rating
Rockers & Paddles
Small Actuators (TN Frame)
D.365” (9.27mm)
Wide Rocker
E.365” (9.27mm)
Wide Paddle
F.450” (11.43mm)
Wide Rocker
G.450” (11.43mm)
Wide Paddle
Large Actuators (TY Frame)
J.595” (15.11mm)
Wide Rocker
H.595” (15.11mm)
Wide Paddle
Rocker & Paddle
Colors
ABlack
BWhite
CRed
EYellow
FGreen
GBlue
HGray
W1 012
Circuits
2ON NONE ON
3ON OFF ON
5ON NONE (ON)
8(ON) OFF (ON)
9ON OFF (ON)
4ON ON ON
6(ON) ON (ON)
7ON ON (ON)
( ) = Momentary
3-ON circuits
*
*
*
*
Mounting Frames
TN .272” (6.9mm) Wide
Flat Frame
TY .504” (12.8mm) Wide
Flat Frame
D C
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
M2012TNW01-DC
Poles
1SPDT
2DPDT
SP3T
33PDT
44PDT
DP3T
Solder Lug Terminals
IMPORTANT:
Switches are supplied without UL & CSA marking unless specified.
UL & CSA recognized only when ordered with marking on the switch.
Specific models, ratings and ordering instructions are noted on the
General Specifications page.
Series M Flat Frame Mount Miniature Rockers
B84
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
Rocker Position
( ) = Momentary Connected Terminals Throw & Schematics
Pole Model
Down Center Up Down Center Up
SP
M2012
M2013
M2015
M2018
M2019
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
2-3 OPEN 2-1
SPDT
DP
M2022
M2023
M2025
M2028
M2029
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
2-3 5-6 OPEN 2-1 5-4
DPDT
3P
M2032
M2033
M2035
M2038
M2039
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
2-3 5-6
8-9 OPEN 2-1 5-4
8-7
3PDT
4P
M2042
M2043
M2045
M2048
M2049
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
2-3 5-6
8-9 11-12 OPEN 2-1 5-4
8-7 11-10
4PDT
Note: Terminal numbers are not actually
on the switch.
POLES & CIRCUITS
11
10
127
9
4
6
1
3
258
(COM)
2 5 (COM) 8
316497
2 (COM)
1
3
4613
25(COM)
For 3 Throw (3-On)
Connected Terminals & Schematics
Pole Model Down Center Up Down Center Up
SP
M2024
M2026
M2027
ON
(ON)
ON
ON
ON
ON
ON
(ON)
(ON)
DP
M2044
M2046
M2047
ON
(ON)
ON
ON
ON
ON
ON
(ON)
(ON)
2-3 5-6 2-3 5-4 2-1 5-4
2-3 5-6 2-3 5-4 2-1 5-4
8-9 11-12 8-9 11-10 8-7 11-10
External connection must be
made during field installation.
The SP3T model utilizes a
double pole base.
External connection must be
made during field installation.
The DP3T model utilizes a
four pole base.
(out)(out)
(out) (out)
(out)
(out)
External
Conn
Common
(in)
Common
(in)
1
2
4710
12 96 3
5811
(out)
63
2
14
5
(out)(out)
External
Conn
Common
(in)
1 (out) 4 (out) 6 (out)
2 (in)
3
5
External
Connection
1 (out) 4 (out) 6 (out)
2 (in)
3
5
External
Connection
1 (out) 4 (out) 6 (out)
2 (in)
3
5
External
Connection
1 (out)
4 (out) 6 (out) 7 (out) 10 (out)
12 (out)
8 (in)2 (in)
39
51
1
External
Connection External
Connection
1 (out)
4 (out) 6 (out) 7 (out) 10 (out)
12 (out)
8 (in)2 (in)
39
51
1
External
Connection
External
Connection
1 (out)
4 (out) 6 (out) 7 (out) 10 (out)
12 (out)
8 (in)2 (in)
39
51
1
External
Connection External
Connection
Series M
Flat Frame Mount Miniature Rockers
B85
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
MOUNTING FRAMES
.272” (6.9mm)
Wide Flat Frame
TN
Small Actuators & Panel Cutouts for TN Frame (actuator details on the following pages)
TY
Mounting hardware kit HK-1, as shown on the
following page, must be ordered separately.
AT4148 AT4149 AT4150 AT4151
Large Actuators & Panel Cutout for TY Frame
(actuator details on the following pages)
AT4156 AT4157
Mounting hardware kit HK-2, as shown on the
following page, must be ordered separately.
.504” (12.8mm)
Wide Flat Frame
(0.6)
.024
(3.5)
.138
(6.9)
.272
(29.5)
1.161
(23.8)
.937
(2.4) Dia Typ
.094
(3.2) Dia
Typ
.126
(12.8)
.504
(41.3)
1.626
(34.9)
1.374
(0.6)
.024
(3.5)
.138
(16.0)
.630
(28.5)
1.122
(34.9)
1.374
(3.5) Dia Ty
p
.138
(23.8)
.937
(12.7)
.500
(12.4)
.490
(2.6) Dia Ty
p
.102
(17.8)
.701
(23.8)
.937
(2.6) Dia Ty
p
.102
(10.1)
.398
Series M Flat Frame Mount Miniature Rockers
B86
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
CONTACT MATERIALS & RATINGS
Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC
Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum
Note: See Supplement section to find complete explanation of operating range.
Gold over Silver Power Level
or Logic Level
6A @ 125V AC
or 0.4VA maximum @ 28V AC/DC maximum
Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the
same application. See Supplement section to find complete explanation of dual rating and operating range.
A
W
G
TERMINALS
01
03
Solder Lug
.250” (6.35mm)
Straight PC
Single Pole Double Pole Three Pole Four Pole
Epoxy Seal
(2.0)
.079 (2.0)
.079
(4.0)
.157
(1.1)
.043
Thk = (0.8)
.031
(4.8) Typ
.189
(4.7) Ty
p
.185
(1.8) Dia Typ
.073
1
2
36
5
47
8
9
(4.8) Typ
.189
(4.7) Typ
.185
(1.8) Dia Ty
p
.073
1
2
36
5
47
8
912
11
10
(4.7) Typ
.185
(1.8) Dia Ty
p
.073
1
2
3
MOUNTING FRAMES (CONTINUED)
Optional Hardware Kits
for Subpanel or Face Panel Mounting
Frame
Panel
Thickness
Standoff
Length
Hardware
Kit Number
TN Frame .125” (3.175mm) .233” (5.918mm) ATHK-1
TY Frame .125” (3.175mm) .312” (7.925mm) ATHK-2
Hardware kits include:
2 stainless steel screws, 2 hex nuts, 2 lockwashers, & 2 standoffs
STANDOFF
LENGTH
Face Panel Mounting Subpanel Mounting
Flat frame devices may
also be mounted to the
face panel. Standoffs
are used to recess the
actuator and achieve
an attractive front panel
appearance.
These devices are especially
designed for subpanel mounting.
When installed on a mounting
plate behind the panel, hardware
is completely concealed and
the front panel retains a clean,
attractive appearance.
Optional Snap-in Panel Frames
Further
details are
shown in
the previous
bracketed
PC mount
subsection.
AT064-1
AT064-2
AT065-1
AT065-2
Epoxy Seal
(4.8)
.189
(6.35)
.250
(1.17)
.046
Thk = (0.8)
.031
(4.7) Ty
p
.185
(4.8)
.189
(1.8) Dia Typ
.073
1
2
36
5
4
Series M
Flat Frame Mount Miniature Rockers
B87
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
AT4148 .365” (9.27mm)
Wide Rocker
D
Material: Polyamide
Finish: Matte
AT4149 .365” (9.27mm)
Wide Paddle
E
Material: Polyamide
Finish: Matte
AT4150 .450” (11.43mm)
Wide Rocker
F
Material: Polyamide
Finish: Matte
AT4151 .450” (11.43mm)
Wide Paddle
G
Material: Polyamide
Finish: Matte
(2.36)
.093
(3.18)
.125
(5.84)
R
.230
(16.36)
.644
(3.5)
.138
(11.8)
.465
(11.43)
.450
(6.3)
.248
(8.1)
.319
(11.8)
.465
(9.19)
.362
(3.5)
.138
(7.7)
.303
(11.43)
.450
(2.13)
.084
(3.96)
.156
(8.43)
R
.332
(3.5)
.138
(18.8)
.740
(16.8)
.661
(9.27)
.365
(7.9)
.311
(8.8)
.346
(6.15)
.242
(3.5)
.138
(13.49)
.531
(16.87)
.664
(9.27)
.365
ROCKERS & PADDLES
Black
A
Cap Colors
Available: White
BRed
CYellow
EGreen
FBlue
GGray
H
AT4156 .595” (15.11mm)
Wide Rocker
JAT4157 .595” (15.11mm)
Wide Paddle
H
(15.11)
.595
(11.0)
.433
(23.01)
.906
(6.5)
.256
(8.4)
.331
(3.5)
.138
(26.78)
1.054
(14.33)
.564
(15.11)
.595
(29.82)
1.174
(26.8)
1.055
(2.36)
.093
(4.75)
.187
(13.5) R
.531
(7.3)
.287
(3.5)
.138
Material: Polyamide
Finish: Matte
Material: Polyamide
Finish: Matte
For TN Frame
For TY Frame
Series M Flat Frame Mount Miniature Rockers
B88
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
TYPICAL SWITCH DIMENSIONS
TN Frame • Solder Lug Single Pole
M2012TNW01-DC
TN Frame • Solder Lug Three Pole
M2032TNW01-DC
TN Frame • Solder Lug Four Pole
M2042TNW01-DC
M2022TNW01-DC
TN Frame • Solder Lug Double Pole
(23.8)
.937
(29.5)
1.161
(6.9)
.272
(9.27)
.365
(2.4) Dia Typ
.094
(4.7) Typ
.185
(0.8) Typ
.031
(3.5)
.138
(12.3)
.484
25°
(1.1) x (2.0) Ty
p
.043 x. 079
(0.5)
.020
(4.5)
.177
(10.3)
.406
(0.6)
.024
(7.9)
.311
(9.65)
.380
Circuit Mark
This Side
1
2
3
(13.0)
.512
(7.9)
.311
(2.0)
.079
(23.8)
.937
(29.5)
1.161
(9.27)
.365
(6.9)
.272
(2.4) Dia Typ
.094
(4.7) Typ
.185
(0.8) Typ
.031
(3.5)
.138
(12.3)
.484
25°
(1.1) x (2.0) Typ
.043 x. 079
(0.5)
.020
(4.5)
.177
(0.6)
.024
(7.9)
.311
(9.65)
.380
Circuit Mark
This Side
(10.3)
.406
6
5
41
2
3
(13.0)
.512
(2.0) Typ
.079
(12.7)
.500
(4.8)
.189
(23.8)
.937
(29.5)
1.161
(9.27)
.365
(6.9)
.272
(2.4) Dia Typ
.094
(4.7) Typ
.185
(1.1) x (2.0) Typ
.043 x .079
(0.8) Typ
.031
(0.5)
.020
(0.6)
.024
(7.9)
.311
(12.3)
.484 (3.5)
.138
25°
Circuit Mark
This Side
(9.65)
.380
(12.4)
.488
(4.5)
.177
6
5
41
2
39
8
7
(13.0)
.512
(4.8) Typ
.189
(17.5)
.689
(2.0) Typ
.079
(23.8)
.937
(29.5)
1.161
(9.27)
.365
(6.9)
.272
(2.4) Dia Typ
.094
(4.7) Typ
.185
(1.1) x (2.0) Typ
.043 x .079
(0.8) Typ
.031
(0.5)
.020
(0.6)
.024
(7.9)
.311
(12.3)
.484 (3.5)
.138
25°
Circuit Mark
This Side
(9.65)
.380 (12.4)
.488
(4.5)
.177
6
5
41
2
39
8
710
11
12
(13.0)
.512
(22.3)
.878
(4.8) Typ
.189
(2.0) Typ
.079
Series M
Flat Frame Mount Miniature Rockers
B89
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable Toggles
B
Rockers
Touch Tilt
www.nkkswitches.com
TYPICAL SWITCH DIMENSIONS
TY Frame • Solder Lug
M2012TYW01-JC
Three Pole TY Frame • Solder Lug
M2032TYW01-JC
Four Pole TY Frame • Solder Lug
M2042TYW01-JC
Single Pole Double Pole
(34.9)
1.374
(41.3)
1.626
(15.11)
.595
(12.8)
.504
(3.2) Dia Typ
.126 (14.5)
.571 (3.5)
.138
25°
(8.4)
.331
(0.6)
.024
(0.5)
.020
(10.0)
.394
(12.1)
.476 (4.5)
.177
(0.8) Typ
.031
(4.7) Typ
.185
(1.1) x (2.0) Typ
.043 x .079
Circuit Mark
This Side
6
5
41
2
39
8
7
(13.0)
.512
(4.8) Ty
p
.189
(17.5)
.689
(2.0) Typ
.079
6
5
41
2
39
8
710
11
12
(13.0)
.512
(22.3)
.878
(4.8) Ty
p
.189
(2.0) Typ
.079
(14.5)
.571 (3.5)
.138
25°
(8.4)
.331
(0.6)
.024
(0.5)
.020
(10.0)
.394
(12.1)
.476
(4.5)
.177
(0.8) Typ
.031
(4.7) Typ
.185
(1.1) x (2.0) Typ
.043 x .079
Circuit Mark
This Side
(34.9)
1.374
(41.3)
1.626
(15.11)
.595
(12.8)
.504
(3.2) Dia Typ
.126
(34.9)
1.374
(41.3)
1.626
(15.11)
.595
(12.8)
.504
(3.2) Dia Typ
.126
25°
(0.8) Typ
.031
(4.7) Typ
.185
(10.0)
.394
(10.0)
.394
(4.5)
.177
(0.5)
.020
(0.6)
.024
(8.4)
.331
(14.5)
.571 (3.5)
.138
(1.1) x (2.0) Typ
.043 x .079
Circuit Mark
This Side
1
2
3
(7.9)
.311
(2.0)
.079
(13.0)
.512
6
5
41
2
3
(4.8)
.189
(2.0) Typ
.079
(13.0)
.512
Double pole has barrier between terminals.
Series M Flat Frame Mount Miniature Rockers
B90
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable
B
Rockers
Touch Tilt Toggles
www.nkkswitches.com
LEGENDS
NKK Switches can provide custom legends for caps. Contact factory for more information.
Suggested Printable Area for Caps
AT4148 AT4150
Shaded areas are printable areas.
Recommended Print Method:
Pad Print
Epoxy based ink is recommended.
OFF
ON
OFF
ON
AT4156
OFF
ON
(9.27)
.365
(7.75)
.305
(5.76) Ty
p
.227
(6.9)
Typ
.272
(0.76)
Typ
.030
(0.76) Typ
.030
(0.38) Typ
.015
(9.91)
.390
(3.36) Ty
p
.132
(11.43)
.450
(0.76) Typ
.030
(0.76)
Typ
.030
(0.38) Typ
.015
(4.5)
Typ
.177
(15.11)
.595
(13.59)
.535
(11.18)
Typ
.440
(10.03) Ty
p
.395
(0.76) Typ
.030
(0.76) Typ
.030
(0.38) Typ
.015
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
NKK Switches:
M2012TXG41-DC M2012TXG30-DC M2028TXW13-DF M2012TXW15-DH M2012TXW30-FA M2012TZG23-JB
M2013TXG30-DA M2018TXG13-DA M2018TXW13-EA M2019TXG30-FA M2022TXG13-DA M2022TXW13-DA
M2022TXW13-FA M2022TXW13-GA M2022TXW23/U-DB M2023TXG41-FA M2032TXW30-DA M2022TXG15/108-
KA-RO M2012TXW41-FC M2013TXG13-DC M2015TXG23-DA M2018TXG13-DB M2018TXG13-FB M2018TXG41-
EC M2018TXW13-FB M2018TXW13/UC M2018TXW13/UC-GA M2018TZW13-JE M2019TXG13-GB M2022TXG13-
DC M2022TZW13 M2022TZW13-JB M2022TZW13/UC M2023TXW13-EA M2023TXW13-FA M2024TXW13-EB
M2026TXG13-GA M2028TXG13-DC M2028TXG13-FC M2047TXG41-DA M2012TXW15-DA-RO M2012TXG15-DA-
RO M2023TXW15-DA-RO M2023TXG15-DA-RO M2013TXW25-DA M2013TXW25-DF M2013TXW25-DC
M2022TXG30-DC M2018TXW13/CUL-GA M2022TXW23-DG M2022TXG30-DB M2029TXG41-DA
M2012TXG13/108-DA-RO M2012TZW23/U-JB M2015TZG23-JH M2019TXG13-DA-RO M2022TXW41-FA
M2032TXG30-DC M2027TXG30-DA M2012TZW23/U-JC M2012TXG13-GA M2015TXG13-EB M2019TXG45-DA
M2039TXA41 M2039TXA41-DA M2023TXA13-DH M2023TXG30-FA M2022TXW30-EA M2023TXW13-DH
M2012TXW13-GB M2015TXG13-GB M2029TXW30-DC M2029TXW13-DC M2028TXW13-GA M2018TXW13-EE
M2018TXW03 M2012TXW30/UC/328-DA M2023TXG13-DB M2025TXW13 M2013TXW41-DA M2012TXW13-DE
M2018TXW30 M2022TXG13-DB M2039TXW41-DA M2012TXW45/U M2018TXG41-FA M2015TXW41
M2022TZW24 M2012TXG41-FA M2018TXW26 M2029TXW13-GA M2013TXW30-DA M2012TXG13-GB
M2013TXG13-FA M2015TXG23-FH M2018TXG41 M2012TXG23-DB M2022TZW13-JH M2033TXW41
M2012TXW26-DA