XC7SET32GW,125 - NXP Semiconductors

1. General description

XC7SET32 is a high-speed Si-gate CMOS device. It provides a 2-input OR function.

2. Features

nSymmetrical output impedance

nHigh noise immunity

nESD protection:

uHBM JESD22-A114E: exceeds 2000 V

uMM JESD22-A115-A: exceeds 200 V

uCDM JESD22-C101C: exceeds 1000 V

nLow power dissipation

nBalanced propagation delays

nSOT353-1 and SOT753 package options

nSpeciﬁed from −40 °C to +125 °C

3. Ordering information

XC7SET32

2-input OR gate

Rev. 01 — 3 September 2009 Product data sheet

Table 1. Ordering information

Type number Package

Temperature range Name Description Version

XC7SET32GW −40 °C to +125 °C TSSOP5 plastic thin shrink small outline package; 5 leads;

body width 1.25 mm SOT353-1

XC7SET32GV −40 °C to +125 °C SC-74A plastic surface-mounted package; 5 leads SOT753

Product data sheet Rev. 01 — 3 September 2009 2 of 11

NXP Semiconductors XC7SET32

2-input OR gate

4. Marking

[1] The pin 1 indicator is located on the lower left corner of the device, below the marking code.

5. Functional diagram

6. Pinning information

6.1 Pinning

Table 2. Marking codes

Type number Marking code[1]

XC7SET32GW gG

XC7SET32GV g32

Fig 1. Logic symbol Fig 2. IEC logic symbol

mna164

mna165

≥1

Fig 3. Logic diagram

mna166

Fig 4. Pin conﬁguration SOT353-1 (TSSOP5) and SOT753 (SC-74A)

XC7SET32

GND Y

001aak116

Product data sheet Rev. 01 — 3 September 2009 3 of 11

NXP Semiconductors XC7SET32

2-input OR gate

6.2 Pin description

7. Functional description

8. Limiting values

[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed.

[2] For both TSSOP5 and SC-74A packages: above 87.5 °C the value of Ptot derates linearly with 4.0 mW/K.

Table 3. Pin description

Symbol Pin Description

B 1 data input

A 2 data input

GND 3 ground (0 V)

Y 4 data output

VCC 5 supply voltage

Table 4. Function table

H = HIGH voltage level; L = LOW voltage level

Inputs Output

ABY

LLL

LHH

HLH

HHH

Table 5. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134).

Symbol Parameter Conditions Min Max Unit

VCC supply voltage −0.5 +7.0 V

VIinput voltage −0.5 +7.0 V

IIK input clamping current VI < −0.5 V −20 - mA

IOK output clamping current VO < −0.5 V or VO>V

CC + 0.5 V [1] -±20 mA

IOoutput current −0.5 V < VO <V

CC + 0.5 V - ±25 mA

ICC supply current - 75 mA

IGND ground current −75 - mA

Tstg storage temperature −65 +150 °C

Ptot total power dissipation Tamb = −40 °C to +125 °C[2] - 250 mW

Product data sheet Rev. 01 — 3 September 2009 4 of 11

NXP Semiconductors XC7SET32

2-input OR gate

9. Recommended operating conditions

10. Static characteristics

Table 6. Recommended operating conditions

Voltages are referenced to GND (ground = 0 V).

Symbol Parameter Conditions Min Typ Max Unit

VCC supply voltage 4.5 5.0 5.5 V

VIinput voltage 0 - 5.5 V

VOoutput voltage 0 - VCC V

Tamb ambient temperature −40 +25 +125 °C

∆t/∆V input transition rise and fall rate - - 20 ns/V

Table 7. Static characteristics

Voltages are referenced to GND (ground = 0 V).

Symbol Parameter Conditions 25 °C−40 °C to +85 °C−40 °C to +125 °C Unit

Min Typ Max Min Max Min Max

VIH HIGH-level

input voltage VCC = 4.5 V to 5.5 V 2.0 - - 2.0 - 2.0 - V

VIL LOW-level

input voltage VCC = 4.5 V to 5.5 V - - 0.8 - 0.8 - 0.8 V

VOH HIGH-level

output voltage VI= VIH or VIL; VCC = 4.5 V

IO=−50 µA 4.4 4.5 - 4.4 - 4.4 - V

IO=−8.0 mA 3.94 - - 3.8 - 3.70 - V

VOL LOW-level

output voltage VI= VIH or VIL; VCC = 4.5 V

IO= 50 µA - 0 0.1 - 0.1 - 0.1 V

IO= 8.0 mA - - 0.36 - 0.44 - 0.55 V

IIinput leakage

current VI= 5.5 Vor GND;

VCC = 0 V to 5.5 V - - 0.1 - 1.0 - 2.0 µA

ICC supply current VI=V

CC or GND; IO = 0 A;

VCC = 5.5 V - - 1.0 - 10 - 40 µA

∆ICC additional

supply current per input pin; VI= 3.4 V;

other inputs at VCC or GND;

IO= 0 A; VCC = 5.5 V

- - 1.35 - 1.5 - 1.5 mA

CIinput

capacitance - 1.5 10 - 10 - 10 pF

Product data sheet Rev. 01 — 3 September 2009 5 of 11

NXP Semiconductors XC7SET32

2-input OR gate

11. Dynamic characteristics

[1] tpd is the same as tPLH and tPHL.

[2] Typical values are measured at VCC = 5.0 V.

[3] CPD is used to determine the dynamic power dissipation PD(µW).

PD=C

PD ×VCC2×fi+∑(CL×VCC2×fo) where:

fi= input frequency in MHz;

fo= output frequency in MHz;

CL= output load capacitance in pF;

VCC = supply voltage in V.

Table 8. Dynamic characteristics

GND = 0 V. For waveform see Figure 5. For test circuit see Figure 6.

Symbol Parameter Conditions 25 °C−40 °C to +85 °C−40 °C to +125 °C Unit

Min Typ Max Min Max Min Max

tpd propagation

delay A and B to Y;

see Figure 5;

VCC = 4.5 V to 5.5 V

[1]

[2]

CL= 15 pF - 3.3 6.9 1.0 8.0 1.0 9.0 ns

CL= 50 pF - 4.8 7.9 1.0 9.0 1.0 10 ns

CPD power

dissipation

capacitance

per buffer;

CL=50pF;f=1 MHz;

VI= GND to VCC

[3] -17- - - - - pF

Product data sheet Rev. 01 — 3 September 2009 6 of 11

NXP Semiconductors XC7SET32

2-input OR gate

12. Waveforms

Measurement points are given in Table 9.

Fig 5. The input (A and B) to output (Y) propagation delays

mna167

A, B input

Y output

tPHL tPLH

Table 9. Measurement points

Type number Input Output

VIVMVM

XC7SET32 GND to 3.0 V 1.5 V 0.5 × VCC

Test data is given in Table 10.

Deﬁnitions for test circuit:

CL = Load capacitance including jig and probe capacitance.

RT = Termination resistance should be equal to output impedance Zo of the pulse generator.

Fig 6. Load circuitry for switching times

mna101

VCC

VIVO

RTCL

PULSE

GENERATOR DUT

Table 10. Test data

Type Input Load Test

VItr, tfCL

XC7SET32 3.0 V ≤3.0 ns 15 pF, 50 pF tPLH, tPHL

Product data sheet Rev. 01 — 3 September 2009 7 of 11

NXP Semiconductors XC7SET32

2-input OR gate

13. Package outline

Fig 7. Package outline SOT353-1 (TSSOP5)

UNIT A1

max. A2A3bpLHELpwyv

ceD(1) E(1) Z(1) θ

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

mm 0.1

01.0

0.8 0.30

0.15 0.25

0.08 2.25

1.85 1.35

1.15 0.65

1.3 2.25

2.0 0.60

0.15 7°

0°

0.1 0.10.30.425

DIMENSIONS (mm are the original dimensions)

Note

1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.

0.46

0.21

SOT353-1 MO-203 SC-88A 00-09-01

03-02-19

0.15

(A3)

detail X

vMA

1.5 3 mm0

scale

TSSOP5: plastic thin shrink small outline package; 5 leads; body width 1.25 mm SOT353-1

1.1

Product data sheet Rev. 01 — 3 September 2009 8 of 11

NXP Semiconductors XC7SET32

2-input OR gate

Fig 8. Package outline SOT753 (SC-74A)

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

SOT753 SC-74A

wBM

detail X

vMA

0 1 2 mm

scale

132

Plastic surface-mounted package; 5 leads SOT753

UNIT A1bpcDEHELpQywv

mm 0.100

0.013 0.40

0.25 3.1

2.7

0.26

0.10 1.7

1.3

0.95 3.0

2.5 0.2 0.10.2

DIMENSIONS (mm are the original dimensions)

0.6

0.2 0.33

0.23

1.1

0.9

02-04-16

06-03-16

Product data sheet Rev. 01 — 3 September 2009 9 of 11

NXP Semiconductors XC7SET32

2-input OR gate

14. Abbreviations

15. Revision history

Table 11. Abbreviations

Acronym Description

CDM Charged Device Model

DUT Device Under Test

ESD ElectroStatic Discharge

HBM Human Body Model

MM Machine Model

Table 12. Revision history

Document ID Release date Data sheet status Change notice Supersedes

XC7SET32_1 20090903 Product data sheet - -

Product data sheet Rev. 01 — 3 September 2009 10 of 11

NXP Semiconductors XC7SET32

2-input OR gate

16. Legal information

16.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term ‘short data sheet’ is explained in section “Deﬁnitions”.

[3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status

information is available on the Internet at URL http://www.nxp.com.

16.2 Deﬁnitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modiﬁcations or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liability for the consequences of

use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and title. A short data sheet is intended

for quick reference only and should not be relied upon to contain detailed and

full information. For detailed and full information see the relevant full data

sheet, which is available on request via the local NXP Semiconductors sales

ofﬁce. In case of any inconsistency or conﬂict with the short data sheet, the

full data sheet shall prevail.

16.3 Disclaimers

General — Information in this document is believed to be accurate and

reliable. However, NXP Semiconductors does not give any representations or

warranties, expressed or implied, as to the accuracy or completeness of such

information and shall have no liability for the consequences of use of such

information.

Right to make changes — NXP Semiconductors reserves the right to make

changes to information published in this document, including without

limitation speciﬁcations and product descriptions, at any time and without

notice. This document supersedes and replaces all information supplied prior

to the publication hereof.

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suitable for use in medical, military, aircraft,

space or life support equipment, nor in applications where failure or

malfunction of an NXP Semiconductors product can reasonably be expected

to result in personal injury, death or severe property or environmental

damage. NXP Semiconductors accepts no liability for inclusion and/or use of

NXP Semiconductors products in such equipment or applications and

therefore such inclusion and/or use is at the customer’s own risk.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. NXP Semiconductors makes no

representation or warranty that such applications will be suitable for the

speciﬁed use without further testing or modiﬁcation.

Limiting values — Stress above one or more limiting values (as deﬁned in

the Absolute Maximum Ratings System of IEC 60134) may cause permanent

damage to the device. Limiting values are stress ratings only and operation of

the device at these or any other conditions above those given in the

Characteristics sections of this document is not implied. Exposure to limiting

values for extended periods may affect device reliability.

Terms and conditions of sale — NXP Semiconductors products are sold

subject to the general terms and conditions of commercial sale, as published

at http://www.nxp.com/proﬁle/terms, including those pertaining to warranty,

intellectual property rights infringement and limitation of liability, unless

explicitly otherwise agreed to in writing by NXP Semiconductors. In case of

any inconsistency or conﬂict between information in this document and such

terms and conditions, the latter will prevail.

No offer to sell or license — Nothing in this document may be interpreted

or construed as an offer to sell products that is open for acceptance or the

grant, conveyance or implication of any license under any copyrights, patents

or other industrial or intellectual property rights.

Export control — This document as well as the item(s) described herein

may be subject to export control regulations. Export might require a prior

authorization from national authorities.

16.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks

are the property of their respective owners.

17. Contact information

For more information, please visit: http://www.nxp.com

For sales ofﬁce addresses, please send an email to: salesaddresses@nxp.com

Document status[1][2] Product status[3] Deﬁnition

Objective [short] data sheet Development This document contains data from the objective speciﬁcation for product development.

Preliminary [short] data sheet Qualiﬁcation This document contains data from the preliminary speciﬁcation.

Product [short] data sheet Production This document contains the product speciﬁcation.

NXP Semiconductors XC7SET32

2-input OR gate

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 3 September 2009

Document identifier: XC7SET32_1

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section ‘Legal information’.

18. Contents

1 General description. . . . . . . . . . . . . . . . . . . . . . 1

2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

3 Ordering information. . . . . . . . . . . . . . . . . . . . . 1

4 Marking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

5 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2

6 Pinning information. . . . . . . . . . . . . . . . . . . . . . 2

6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3

7 Functional description . . . . . . . . . . . . . . . . . . . 3

8 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 3

9 Recommended operating conditions. . . . . . . . 4

10 Static characteristics. . . . . . . . . . . . . . . . . . . . . 4

11 Dynamic characteristics . . . . . . . . . . . . . . . . . . 5

12 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

13 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . 7

14 Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . . 9

15 Revision history. . . . . . . . . . . . . . . . . . . . . . . . . 9

16 Legal information. . . . . . . . . . . . . . . . . . . . . . . 10

16.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 10

16.2 Deﬁnitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

16.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 10

16.4 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 10

17 Contact information. . . . . . . . . . . . . . . . . . . . . 10

18 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11