K8C5515EBM-FE1F - Samsung Semiconductor Division

Revision 1.5

K8C54(55)15ET(B)M

- 1 -

NOR FLASH MEMORY

December, 2006

256Mb M-die MLC NOR Specification

INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO SAMSUNG PRODUCTS, AND IS SUB-

JECT TO CHANGE WITHOUT NOTICE.

NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY LICENSE, EXPRESS OR

IMPLIED, BY ESTOPPEL OR OTHERWISE,

TO ANY INTELLECTUAL PROPERTY RIGHTS IN SAMSUNG PRODUCTS OR TECHNOLOGY. ALL INFOR-

MATION IN THIS DOCUMENT IS PROVIDED

ON AS "AS IS" BASIS WITHOUT GUARANTEE OR WARRANTY OF ANY KIND.

1. For updates or additional information about Samsung products, contact your nearest Samsung office.

2. Samsung products are not intended for use in life support, critical care, medical, safety equipment, or similar applications

where Product failure couldresult in loss of life or personal or physical harm, or any military or defense application, or any

governmental procurement to which special terms or provisions may apply.

* Samsung Electronics reserves the right to change products or specification without notice.

Revision 1.5

K8C54(55)15ET(B)M

- 2 -

NOR FLASH MEMORY

December, 2006

Document Title

256M Bit (16M x16) Sync Burst , Multi Bank MLC NOR Flash Memory

Revision History

Revision No.

0.0

0.5

0.6

0.7

0.8

1.0

1.1

1.2

1.3

1.4

1.5

History

Initial

Preliminary

- Added Burst Access time(11ns@66Mhz, 9ns@83Mhz)

- Correct the Active Write Current (typ.15mA, max.30mA --> typ.25mA,

max.40mA)

- Correct tBDH(Data Hold Time from Next Clock Cycle) from

4ns(@66MHz), 2.25ns(@108MHz), 1.5ns(@133MHz) to

3ns(@66MHz), 2ns(@108MHz), 2ns(@133MHz)

- Correct tRDYA(Clock to RDY Setup Time) from 8ns(@83Mhz) to

9ns(@83MHz)

- Correct tRDYS(RDY setup to Clock) from 4ns(@66MHz),

2.25ns(@108MHz), 1.5ns(@133MHz) to 3ns(@66MHz),

2ns(@108MHz), 2ns(@133MHz)

- Correct typo

- Add Ordering Information for Density

56 : 256Mb for 66/83MHz, 57 : 267Mb for 108/133Mhz

- Add Product Classification Table (Table 1-1)

- Change tAVDH(AVD Hold Time from CLK) from 6ns(@66MHz),

5ns(@83MHz) to 2ns(@66/83MHz)

- Delete tOH(Output Hold Time from Address, CE or OE ) from Asynchronous

Read parameter

- CFI note is added (Max Operation frequency : Data 53H is in 66/83Mhz

part

- tAVDO is deleted

- Specification is finalized

Active Asynchronous read Current(@1Mhz) is changed

3mA(typ.),5mA(max.) to 8mA(typ.), 10mA(max.)

'In erase/program suspend followed by resume operation, min. 200ns is

needed for checking the busy status' is added

Frequency information is added to Programmable Wait State at Burst

Mode Configuration Register Table.

"Asynchronous mode may not support read following four sequential invalid

read condition within 200ns." is added

Correct typo

In write buffer programming part, "And from the third cycle to the last cycle

of Write to Buffer command is also required when using Write-Buffer-Pro-

gramming features in Unlock Bypass mode." is added.

2 AC parameters are changed.

At 66MHz and 83MHz, change tBDH form 3ns to 4ns.

At 108MHz and 133MHz, change tBDH form 2ns to 3ns.

Change tCES form 6ns to 5ns at all frequency regions.

Add Synchronous Read Mode Setting by A19

Change tCES form 5ns to 4.5ns at all frequency regions.

Registered as a new part ID, K8C54(55)15ET(B)M.

Ordering Information is updated.

Draft Date

April 1, 2005

September 1, 2005

November 7, 2005

December 7, 2005

April 04,2006

April 25,2006

September 08,2006

October 17, 2006

October 19, 2006

December 04, 2006

December 27, 2006

Remark

Advance

Preliminary

Table of Contents

Revision 1.5

November 2006

K8C54(55)15ET(B)M

- 1 -

NOR FLASH MEMORY

FEATURES 1

GENERAL DESCRIPTION............................................................................................................................................... 1

PIN DESCRIPTION .......................................................................................................................................................... 2

Pin Configuration .............................................................................................................................................................. 3

Ball FBGA VIEW .............................................................................................................................................................. 4

FUNCTIONAL BLOCK DIAGRAM.................................................................................................................................... 4

ORDERING INFORMATION ............................................................................................................................................ 5

PRODUCT INSTRUCTION .............................................................................................................................................. 18

COMMAND DEFINITIONS............................................................................................................................................... 19

DEVICE OPERATION ...................................................................................................................................................... 21

Read Mode ................................................................................................................................................................. 21

Asynchronous Read Mode .................................................................................................................................... 21

Synchronous (Burst) Read Mode .......................................................................................................................... 21

Continuous Linear Burst Read......................................................................................................................... 21

8-, 16-Word Linear Burst Read .................................................................................................................. 21

Programmable Wait State.......................................................................................................................... 22

Handshaking .............................................................................................................................................. 22

Set Burst Mode Configuration Register....................................................................................................................... 22

Programmable Wait State Configuration.................................................................................................... 23

Burst Read Mode Setting........................................................................................................................... 23

RDY Configuration ..................................................................................................................................... 23

Autoselect Mode ......................................................................................................................................................... 23

Standby Mode............................................................................................................................................................. 23

Autosleep Mode .......................................................................................................................................................... 24

Output Disable Mode .................................................................................................................................................. 24

Block Protection & Unprotection ................................................................................................................................. 24

Hardware Reset .......................................................................................................................................................... 24

Software Reset............................................................................................................................................................ 24

Program ...................................................................................................................................................................... 24

Accelerated Program............................................................................................................................................. 25

Write Buffer Programming..................................................................................................................................... 25

Accelerated Write Buffer Programming................................................................................................................. 25

Chip Erase .................................................................................................................................................................. 26

Block Erase................................................................................................................................................................. 26

Unlock Bypass ............................................................................................................................................................ 26

Erase Suspend / Resume ........................................................................................................................................... 26

Program Suspend / Resume....................................................................................................................................... 27

Read While Write Operation ....................................................................................................................................... 27

OTP Block Region....................................................................................................................................................... 27

Low VCC Write Inhibit................................................................................................................................................. 27

Write Pulse “Glitch” Protection.................................................................................................................................... 27

Logical Inhibit .............................................................................................................................................................. 27

Deep Power Down ...................................................................................................................................................... 27

FLASH MEMORY STATUS FLAGS ................................................................................................................................. 29

DQ7 : Data Polling ...................................................................................................................................................... 29

DQ6 : Toggle Bit.......................................................................................................................................................... 29

DQ5 : Exceed Timing Limits........................................................................................................................................ 29

DQ3 : Block Erase Timer ............................................................................................................................................ 30

DQ2 : Toggle Bit 2....................................................................................................................................................... 30

DQ1 : Buffer Program Abort Indicator ......................................................................................................................... 30

RDY: Ready ................................................................................................................................................................ 30

Commom Flash Memory Interface ................................................................................................................................... 31

ABSOLUTE MAXIMUM RATINGS ................................................................................................................................... 33

Table of Contents

Revision 1.5

November 2006

K8C54(55)15ET(B)M

- 2 -

NOR FLASH MEMORY

RECOMMENDED OPERATING CONDITIONS ( Voltage reference to GND ) ................................................................ 34

DC CHRACTERISTICS .................................................................................................................................................... 34

CAPACITANCE(TA = 25 ×C, VCC = 1.8V, f = 1.0MHz)................................................................................................... 34

AC TEST CONDITION ..................................................................................................................................................... 35

AC CHARACTERISTICS................................................................................................................................................. 35

Synchronous/Burst Read ..................................................................................................................................... 35

Asynchronous Read.................................................................................................................................................... 38

Erase/Program Operation ........................................................................................................................................... 41

Erase/Program Performance ...............................................................................................................................42

Crossing of First Word Boundary in Burst Read Mode..................................................................................................... 47

Case1 : Start from "16N" address group..................................................................................................................... 48

Case2 : Start from "16N+2" address group................................................................................................................. 48

Case3 : Start from "16N+3" address group................................................................................................................. 49

Case4 : Start from "16N+15" address group............................................................................................................... 49

Case5 : Start from "16N+15" address group............................................................................................................... 50

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 1 -

NOR FLASH MEMORY

256M Bit (16M x16) Synch Burst , Multi Bank MLC NOR Flash Memory

FEATURES

GENERAL DEK8C54SCRIPTION

The K8C54(55)15E featuring single 1.8V power supply is a 256Mbit Burst Multi Bank Flash Memory organized as 16Mx16. The memory

architecture of the device is designed to divide itsK8C55 memory arrays into 259 blocks with independent hardware protection. This block

architecture provides highly flexible erase and program capability. The K8C54(55)15E NOR Flash consists of sixteen banks. This device is

capable of reading data from one bank while programming or erasing in the other bank.

Regarding read access time, the K8C5415E provides an 11ns burst access time and an 100ns initial access time at 66MHz.

At 83Mhz, the K8C5415E provides an 9ns burst access time and an 100ns initial access time at 83MHz. At 108Mhz, the K8C5515E provides

an 7ns burst access time and an 100ns initial access time at 83MHz. At 133MHz, the K8C5515E provides an 6ns burst access time and 100ns

initial access time. The device performs a program operation in units of 16 bits (Word) and erases in units of a block. Single or multiple blocks

can be erased. The block erase operation is completed within typically 0.6sec. The device requires 25mA as program/erase current in the

extended temperature ranges.

The K8C54(55)15E NOR Flash Memory is created by using Samsung's advanced CMOS process technology.

• Single Voltage, 1.7V to 1.95V for Read and Write operations

• Organization

- 16,777,216 x 16 bit ( Word Mode Only)

• Read While Program/Erase Operation

• Multiple Bank Architecture

- 16 Banks (16Mb Partition)

• OTP Block : Extra 512-Word block

• Read Access Time (@ CL=30pF)

- Asynchronous Random Access Time : 100ns

- Synchronous Random Access Time :100ns

- Burst Access Time :

11ns(66Mhz) / 9ns(83Mhz) / 7ns (108MHz) / 6ns (133MHz)

• Burst Length :

- Continuous Linear Burst

- Linear Burst : 8-word & 16-word with No-wrap & Wrap

• Block Architecture

- Four 16Kword blocks and two hundreds fifty-five 64Kword blocks

- Bank 0 contains four 16 Kword blocks and fifteen 64Kword blocks

- Bank 1 ~ Bank 15 contain two hundred forty 64Kword blocks

• Reduce program time using the VPP

• Support 32 words Buffer Program

• Power Consumption (Typical value, CL=30pF)

- 16-word Synchronous Read Current : 35mA at 133MHz

- Program/Erase Current : 25mA

- Read While Program/Erase Current : 45mA

- Standby Mode/Auto Sleep Mode : 30uA

• Block Protection/Unprotection

- Using the software command sequence

- Last two boot blocks are protected by WP=VIL

- All blocks are protected by VPP=VIL

• Handshaking Feature

- Provides host system with minimum latency by monitoring RDY

• Erase Suspend/Resume

• Program Suspend/Resume

• Unlock Bypass Program/Erase

• Hardware Reset (RESET)

• Deep Power Down Mode

• Data Polling and Toggle Bits

- Provides a software method of detecting the status of program

or erase completion

• Endurance

100K Program/Erase Cycles Minimum

• Data Retention : 10 years

• Extended Temperature : -25°C ~ 85°C

• Support Common Flash Memory Interface

• Low Vcc Write Inhibit

• Package : 167-Ball FBGA type, 10.5mm x 14.0mm

0.8mm ball pitch

1.4mm (Max.) Thickness

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 2 -

NOR FLASH MEMORY

PIN DESCRIPTION

SAMSUNG ELECTRONICS CO., LTD. reserves the right to change products and specifications without notice.

Pin Name Pin Function

A0 - A23 Address Inputs

DQ0 - DQ15 Data input/output

CE Chip Enable

OE Output Enable

RESET Hardware Reset Pin

VPP Accelerates Programming

WE Write Enable

WP Hardware Write Protection Input

CLK Clock

RDY Ready Output

AVD Address Valid Input

DPD Deep Power Down

Vcc Power Supply

VSS Ground

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 3 -

NOR FLASH MEMORY

Pin Configuration

DNU DNU DNU DNU DNU

NC VSS NC A17 VCC NC NC WE NC VSS NC NC

WP A1 A4 A7 VPP NC NC VSS A9 A15 A22 NC

NC A2 A5 A18 A21 RESET A20 A10 A11 A14 A23

NC A3 A6 NC NC CLK NC A19 A12 A13 NC VSS

NC VSS NC NC NC AVD NC A8 NC NC NC NC

NC NC NC NC NC NC A16 NC NC NC NC NC

NC NC NC NC NC NC DPD DQ13 NC NC NC NC

NC NC NC NC NC NC DQ8 DQ9 NC NC NC VSS

NC VSS NC NC NC A0 DQ4 NC NC NC NC NC

NC NC NC NC NC DQ1 DQ11 DQ12 DQ6 NC NC NC

NC VSS NC CE DQ0 DQ2 DQ10 DQ5 DQ14 DQ7 DQ15 NC

VCC VSS NC OE VCCQ VCCQ DQ3 NC VCCQ VCCQ NC VCC

NC NC NC VSS NC NC NC VSS NC VSS NC NC

DNU DNU DNU DNU DNU DNU

123456789101112

167-FBGA : Top View (Ball Down)

RDY

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 4 -

NOR FLASH MEMORY

Ball FBGA VIEW

0.80

4.40

(Datum A)

0.80

5.60

0.80x14=11.20

14.00±0.10

12345689101112 7

(Datum B)

0.80x11=8.80

10.50±0.10 A

#A1 INDEX MARK

14.00±0.10

10.50±0.10

14.00±0.10

0.32±0.05

1.30±0.10

0.45±0.05

TOP VIEW BOTTOM VIEW

0.10 MAX

#A1

167-∅ 0.45±0.05

0.20 M A B

∅

FUNCTIONAL BLOCK DIAGRAM

Vcc

Vss

RESET

RDY

Interface

Bank

Control

Dec

Y Dec Latch &

Control

Latch &

Control

Dec

Y Dec

Erase

Control

Program

Control

High

Voltage

Gen.

Bank 1

Cell Array

Bank 0

Address

Bank 1

Address

Bank 0

Cell Array

AVD X

Dec

Y Dec Latch &

Control

Bank 15

Cell Array

Block

Inform

Vpp

Bank 15

Address

CLK

I/O

A0~A23

DQ15

DQ0~

DPD

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 5 -

NOR FLASH MEMORY

ORDERING INFORMATION

Table 1. Product Line-up

Table 1-1. Product Classification

Table 2. K8C54(55)15E DEVICE BANK DIVISIONS

K8C54(55)15ET

Mode Speed Option 1C

(66MHz)

(83MHz)

(108MHz)

(133MHz)

VCC=1.7V-

1.95V

Synchronous/Burst Max. Initial Access Time (tIAA, ns) 100 100 100 100

Max. Burst Access Time (tBA, ns) 11 9 7 6

Asynchronous

Max. Access Time (tAA, ns) 100 100 100 100

Max. CE Access Time (tCE, ns) 100 100 100 100

Max. OE Access Time (tOE, ns) 15 15 15 15

Speed/Boot Option Top Bottom

256Mb for 66/83MHz K8C5415ETM K8C5415EBM

256Mb for 108/133MHz K8C5515ETM K8C5515EBM

Bank 0 Bank 1 ~ Bank 15

Mbit Block Sizes Mbit Block Sizes

16 Mbit Four 16Kwords,

fifteen 64Kwords 240 Mbit Two hundred

forty 64Kwords

K 8 C 54 1 5 E T M - F E 1F

Samsung

NOR Flash Memory

Device Type

MLC Synch Burst Operating Temperature Range

C = Commercial Temp. (0 °C to 70 °C)

E = Extended Temp. (-25 °C to 85 °C)

Block Architecture

T = Top Boot Block

B = Bottom Boot Block

Version

1st Generation

Access Time

Refer to Table 1

Operating Voltage Range

1.7 V to 1.95V

Package

F : FBGA

D : FBGA(Lead Free)

Organization

x16 Organization

Density

54 = 256Mbits for 66/83MHz, MRS

Synch Burst

55 = 256Mbits for 108/133MHz,

MRS Synch Burst

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 6 -

NOR FLASH MEMORY

Table 3-1. Top Boot Block Address Table

Bank Block Block Size (x16) Address Range

Bank 0

BA258 16 Kwords FFC000h-FFFFFFh

BA257 16 Kwords FF8000h-FFBFFFh

BA256 16 Kwords FF4000h-FF7FFFh

BA255 16 Kwords FF0000h-FF3FFFh

BA254 64 kwords FE0000h-FEFFFFh

BA253 64 kwords FD0000h-FDFFFFh

BA252 64 kwords FC0000h-FCFFFFh

BA251 64 kwords FB0000h-FBFFFFh

BA250 64 kwords FA0000h-FAFFFFh

BA249 64 kwords F90000h-F9FFFFh

BA248 64 kwords F80000h-F8FFFFh

BA247 64 kwords F70000h-F7FFFFh

BA246 64 kwords F60000h-F6FFFFh

BA245 64 kwords F50000h-F5FFFFh

BA244 64 kwords F40000h-F4FFFFh

BA243 64 kwords F30000h-F3FFFFh

BA242 64 kwords F20000h-F2FFFFh

BA241 64 kwords F10000h-F1FFFFh

BA240 64 kwords F00000h-F0FFFFh

Bank 1

BA239 64 kwords EF0000h-EFFFFFh

BA238 64 kwords EE0000h-EEFFFFh

BA237 64 kwords ED0000h-EDFFFFh

BA236 64 kwords EC0000h-ECFFFFh

BA235 64 kwords EB0000h-EBFFFFh

BA234 64 kwords EA0000h-EAFFFFh

BA233 64 kwords E90000h-E9FFFFh

BA232 64 kwords E80000h-E8FFFFh

BA231 64 kwords E70000h-E7FFFFh

BA230 64 kwords E60000h-E6FFFFh

BA229 64 kwords E50000h-E5FFFFh

BA228 64 kwords E40000h-E4FFFFh

BA227 64 kwords E30000h-E3FFFFh

BA226 64 kwords E20000h-E2FFFFh

BA225 64 kwords E10000h-E1FFFFh

BA224 64 kwords E00000h-E0FFFFh

Bank 2

BA223 64 kwords DF0000h-DFFFFFh

BA222 64 kwords DE0000h-DEFFFFh

BA221 64 kwords DD0000h-DDFFFFh

BA220 64 kwords DC0000h-DCFFFFh

BA219 64 kwords DB0000h-DBFFFFh

BA218 64 kwords DA0000h-DAFFFFh

BA217 64 kwords D90000h-D9FFFFh

BA216 64 kwords D80000h-D8FFFFh

BA215 64 kwords D70000h-D7FFFFh

BA214 64 kwords D60000h-D6FFFFh

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 7 -

NOR FLASH MEMORY

Table 3-1. Top Boot Block Address Table

Bank Block Block Size (x16) Address Range

Bank 2

BA213 64 kwords D50000h-D5FFFFh

BA212 64 kwords D40000h-D4FFFFh

BA211 64 kwords D30000h-D3FFFFh

BA210 64 kwords D20000h-D2FFFFh

BA209 64 kwords D10000h-D1FFFFh

BA208 64 kwords D00000h-D0FFFFh

Bank 3

BA207 64 kwords CF0000h-CFFFFFh

BA206 64 kwords CE0000h-CEFFFFh

BA205 64 kwords CD0000h-CDFFFFh

BA204 64 kwords CC0000h-CCFFFFh

BA203 64 kwords CB0000h-CBFFFFh

BA202 64 kwords CA0000h-CAFFFFh

BA201 64 kwords C90000h-C9FFFFh

BA200 64 kwords C80000h-C8FFFFh

BA199 64 kwords C70000h-C7FFFFh

BA198 64 kwords C60000h-C6FFFFh

BA197 64 kwords C50000h-C5FFFFh

BA196 64 kwords C40000h-C4FFFFh

BA195 64 kwords C30000h-C3FFFFh

BA194 64 kwords C20000h-C2FFFFh

BA193 64 kwords C10000h-C1FFFFh

BA192 64 kwords C00000h-C0FFFFh

Bank 4

BA191 64 kwords BF0000h-BFFFFFh

BA190 64 kwords BE0000h-BEFFFFh

BA189 64 kwords BD0000h-BDFFFFh

BA188 64 kwords BC0000h-BCFFFFh

BA187 64 kwords BB0000h-BBFFFFh

BA186 64 kwords BA0000h-BAFFFFh

BA185 64 kwords B90000h-B9FFFFh

BA184 64 kwords B80000h-B8FFFFh

BA183 64 kwords B70000h-B7FFFFh

BA182 64 kwords B60000h-B6FFFFh

BA181 64 kwords B50000h-B5FFFFh

BA180 64 kwords B40000h-B4FFFFh

BA179 64 kwords B30000h-B3FFFFh

BA178 64 kwords B20000h-B2FFFFh

BA177 64 kwords B10000h-B1FFFFh

BA176 64 kwords B00000h-B0FFFFh

Bank 5

BA175 64 kwords AF0000h-AFFFFFh

BA174 64 kwords AE0000h-AEFFFFh

BA173 64 kwords AD0000h-ADFFFFh

BA172 64 kwords AC0000h-ACFFFFh

BA171 64 kwords AB0000h-ABFFFFh

BA170 64 kwords AA0000h-AAFFFFh

BA169 64 kwords A90000h-A9FFFFh

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 8 -

NOR FLASH MEMORY

Table 3-1. Top Boot Block Address Table

Bank Block Block Size (x16) Address Range

Bank 5

BA168 64 kwords A80000h-A8FFFFh

BA167 64 kwords A70000h-A7FFFFh

BA166 64 kwords A60000h-A6FFFFh

BA165 64 kwords A50000h-A5FFFFh

BA164 64 kwords A40000h-A4FFFFh

BA163 64 kwords A30000h-A3FFFFh

BA162 64 kwords A20000h-A2FFFFh

BA161 64 kwords A10000h-A1FFFFh

BA160 64 kwords A00000h-A0FFFFh

Bank 6

BA159 64 kwords 9F0000h-9FFFFFh

BA158 64 kwords 9E0000h-9EFFFFh

BA157 64 kwords 9D0000h-9DFFFFh

BA156 64 kwords 9C0000h-9CFFFFh

BA155 64 kwords 9B0000h-9BFFFFh

BA154 64 kwords 9A0000h-9AFFFFh

BA153 64 kwords 990000h-99FFFFh

BA152 64 kwords 980000h-98FFFFh

BA151 64 kwords 970000h-97FFFFh

BA150 64 kwords 960000h-96FFFFh

BA149 64 kwords 950000h-95FFFFh

BA148 64 kwords 940000h-94FFFFh

BA147 64 kwords 930000h-93FFFFh

BA146 64 kwords 920000h-92FFFFh

BA145 64 kwords 910000h-91FFFFh

BA144 64 kwords 900000h-90FFFFh

Bank 7

BA143 64 kwords 8F0000h-8FFFFFh

BA142 64 kwords 8E0000h-8EFFFFh

BA141 64 kwords 8D0000h-8DFFFFh

BA140 64 kwords 8C0000h-8CFFFFh

BA139 64 kwords 8B0000h-8BFFFFh

BA138 64 kwords 8A0000h-8AFFFFh

BA137 64 kwords 890000h-89FFFFh

BA136 64 kwords 880000h-88FFFFh

BA135 64 kwords 870000h-87FFFFh

BA134 64 kwords 860000h-86FFFFh

BA133 64 kwords 850000h-85FFFFh

BA132 64 kwords 840000h-84FFFFh

BA131 64 kwords 830000h-83FFFFh

BA130 64 kwords 820000h-82FFFFh

BA129 64 kwords 810000h-81FFFFh

BA128 64 kwords 800000h-80FFFFh

Bank 8

BA127 64 kwords 7F0000h-7FFFFFh

BA126 64 kwords 7E0000h-7EFFFFh

BA125 64 kwords 7D0000h-7DFFFFh

BA124 64 kwords 7C0000h-7CFFFFh

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 9 -

NOR FLASH MEMORY

Table 3-1. Top Boot Block Address Table

Bank Block Block Size (x16) Address Range

Bank 8

BA123 64 kwords 7B0000h-7BFFFFh

BA122 64 kwords 7A0000h-7AFFFFh

BA121 64 kwords 790000h-79FFFFh

BA120 64 kwords 780000h-78FFFFh

BA119 64 kwords 770000h-77FFFFh

BA118 64 kwords 760000h-76FFFFh

BA117 64 kwords 750000h-75FFFFh

BA116 64 kwords 740000h-74FFFFh

BA115 64 kwords 730000h-73FFFFh

BA114 64 kwords 720000h-72FFFFh

BA113 64 kwords 710000h-71FFFFh

BA112 64 kwords 700000h-70FFFFh

Bank 9

BA111 64 kwords 6F0000h-6FFFFFh

BA110 64 kwords 6E0000h-6EFFFFh

BA109 64 kwords 6D0000h-6DFFFFh

BA108 64 kwords 6C0000h-6CFFFFh

BA107 64 kwords 6B0000h-6BFFFFh

BA106 64 kwords 6A0000h-6AFFFFh

BA105 64 kwords 690000h-69FFFFh

BA104 64 kwords 680000h-68FFFFh

BA103 64 kwords 670000h-67FFFFh

BA102 64 kwords 660000h-66FFFFh

BA101 64 kwords 650000h-65FFFFh

BA100 64 kwords 640000h-64FFFFh

BA99 64 kwords 630000h-63FFFFh

BA98 64 kwords 620000h-62FFFFh

BA97 64 kwords 610000h-61FFFFh

BA96 64 kwords 600000h-60FFFFh

Bank 10

BA95 64 kwords 5F0000h-5FFFFFh

BA94 64 kwords 5E0000h-5EFFFFh

BA93 64 kwords 5D0000h-5DFFFFh

BA92 64 kwords 5C0000h-5CFFFFh

BA91 64 kwords 5B0000h-5BFFFFh

BA90 64 kwords 5A0000h-5AFFFFh

BA89 64 kwords 590000h-59FFFFh

BA88 64 kwords 580000h-58FFFFh

BA87 64 kwords 570000h-57FFFFh

BA86 64 kwords 560000h-56FFFFh

BA85 64 kwords 550000h-55FFFFh

BA84 64 kwords 540000h-54FFFFh

BA83 64 kwords 530000h-53FFFFh

BA82 64 kwords 520000h-52FFFFh

BA81 64 kwords 510000h-51FFFFh

BA80 64 kwords 500000h-50FFFFh

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 10 -

NOR FLASH MEMORY

Table 3-1. Top Boot Block Address Table

Bank Block Block Size (x16) Address Range

Bank 11

BA79 64 kwords 4F0000h-4FFFFFh

BA78 64 kwords 4E0000h-4EFFFFh

BA77 64 kwords 4D0000h-4DFFFFh

BA76 64 kwords 4C0000h-4CFFFFh

BA75 64 kwords 4B0000h-4BFFFFh

BA74 64 kwords 4A0000h-4AFFFFh

BA73 64 kwords 490000h-49FFFFh

BA72 64 kwords 480000h-48FFFFh

BA71 64 kwords 470000h-47FFFFh

BA70 64 kwords 460000h-46FFFFh

BA69 64 kwords 450000h-45FFFFh

BA68 64 kwords 440000h-44FFFFh

BA67 64 kwords 430000h-43FFFFh

BA66 64 kwords 420000h-42FFFFh

BA65 64 kwords 410000h-41FFFFh

BA64 64 kwords 400000h-40FFFFh

Bank 12

BA63 64 kwords 3F0000h-3FFFFFh

BA62 64 kwords 3E0000h-3EFFFFh

BA61 64 kwords 3D0000h-3DFFFFh

BA60 64 kwords 3C0000h-3CFFFFh

BA59 64 kwords 3B0000h-3BFFFFh

BA58 64 kwords 3A0000h-3AFFFFh

BA57 64 kwords 390000h-39FFFFh

BA56 64 kwords 380000h-38FFFFh

BA55 64 kwords 370000h-37FFFFh

BA54 64 kwords 360000h-36FFFFh

BA53 64 kwords 350000h-35FFFFh

BA52 64 kwords 340000h-34FFFFh

BA51 64 kwords 330000h-33FFFFh

BA50 64 kwords 320000h-32FFFFh

BA49 64 kwords 310000h-31FFFFh

BA48 64 kwords 300000h-30FFFFh

Bank 13

BA47 64 kwords 2F0000h-2FFFFFh

BA46 64 kwords 2E0000h-2EFFFFh

BA45 64 kwords 2D0000h-2DFFFFh

BA44 64 kwords 2C0000h-2CFFFFh

BA43 64 kwords 2B0000h-2BFFFFh

BA42 64 kwords 2A0000h-2AFFFFh

BA41 64 kwords 290000h-29FFFFh

BA40 64 kwords 280000h-28FFFFh

BA39 64 kwords 270000h-27FFFFh

BA38 64 kwords 260000h-26FFFFh

BA37 64 kwords 250000h-25FFFFh

BA36 64 kwords 240000h-24FFFFh

BA35 64 kwords 230000h-23FFFFh

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 11 -

NOR FLASH MEMORY

Table 3-1. Top Boot Block Address Table

Table 3-1-1. OTP Block Addresses

After entering OTP Block, any issued addresses should be in the range of OTP block address.

Bank Block Block Size (x16) Address Range

Bank 13

BA34 64 kwords 220000h-22FFFFh

BA33 64 kwords 210000h-21FFFFh

BA32 64 kwords 200000h-20FFFFh

Bank 14

BA31 64 kwords 1F0000h-1FFFFFh

BA30 64 kwords 1E0000h-1EFFFFh

BA29 64 kwords 1D0000h-1DFFFFh

BA28 64 kwords 1C0000h-1CFFFFh

BA27 64 kwords 1B0000h-1BFFFFh

BA26 64 kwords 1A0000h-1AFFFFh

BA25 64 kwords 190000h-19FFFFh

BA24 64 kwords 180000h-18FFFFh

BA23 64 kwords 170000h-17FFFFh

BA22 64 kwords 160000h-16FFFFh

BA21 64 kwords 150000h-15FFFFh

BA20 64 kwords 140000h-14FFFFh

BA19 64 kwords 130000h-13FFFFh

BA18 64 kwords 120000h-12FFFFh

BA17 64 kwords 110000h-11FFFFh

BA16 64 kwords 100000h-10FFFFh

Bank 15

BA15 64 kwords 0F0000h-0FFFFFh

BA14 64 kwords 0E0000h-0EFFFFh

BA13 64 kwords 0D0000h-0DFFFFh

BA12 64 kwords 0C0000h-0CFFFFh

BA11 64 kwords 0B0000h-0BFFFFh

BA10 64 kwords 0A0000h-0AFFFFh

BA9 64 kwords 090000h-09FFFFh

BA8 64 kwords 080000h-08FFFFh

BA7 64 kwords 070000h-07FFFFh

BA6 64 kwords 060000h-06FFFFh

BA5 64 kwords 050000h-05FFFFh

BA4 64 kwords 040000h-04FFFFh

BA3 64 kwords 030000h-03FFFFh

BA2 64 kwords 020000h-02FFFFh

BA1 64 kwords 010000h-01FFFFh

BA0 64 kwords 000000h-00FFFFh

OTP

Block Address

A23 ~ A8 Block Size (x16) Address Range*

FFFFh 512words FFFE00h-FFFFFFh

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 12 -

NOR FLASH MEMORY

Table 3-2. Bottom Boot Block Address Table

Bank Block Block Size (x16) Address Range

Bank 15

BA258 64 Kwords FF0000h-FFFFFFh

BA257 64 Kwords FE0000h-FEFFFFh

BA256 64 Kwords FD0000h-FDFFFFh

BA255 64 Kwords FC0000h-FCFFFFh

BA254 64 kwords FB0000h-FBFFFFh

BA253 64 kwords FA0000h-FAFFFFh

BA252 64 kwords F90000h-F9FFFFh

BA251 64 kwords F80000h-F8FFFFh

BA250 64 kwords F70000h-F7FFFFh

BA249 64 kwords F60000h-F6FFFFh

BA248 64 kwords F50000h-F5FFFFh

BA247 64 kwords F40000h-F4FFFFh

BA246 64 kwords F30000h-F3FFFFh

BA245 64 kwords F20000h-F2FFFFh

BA244 64 kwords F10000h-F1FFFFh

BA243 64 kwords F00000h-F0FFFFh

Bank 14

BA242 64 kwords EF0000h-EFFFFFh

BA241 64 kwords EE0000h-EEFFFFh

BA240 64 kwords ED0000h-EDFFFFh

BA239 64 kwords EC0000h-ECFFFFh

BA238 64 kwords EB0000h-EBFFFFh

BA237 64 kwords EA0000h-EAFFFFh

BA236 64 kwords E90000h-E9FFFFh

BA235 64 kwords E80000h-E8FFFFh

BA234 64 kwords E70000h-E7FFFFh

BA233 64 kwords E60000h-E6FFFFh

BA232 64 kwords E50000h-E5FFFFh

BA231 64 kwords E40000h-E4FFFFh

BA230 64 kwords E30000h-E3FFFFh

BA229 64 kwords E20000h-E2FFFFh

BA228 64 kwords E10000h-E1FFFFh

BA227 64 kwords E00000h-E0FFFFh

Bank 13

BA226 64 kwords DF0000h-DFFFFFh

BA225 64 kwords DE0000h-DEFFFFh

BA224 64 kwords DD0000h-DDFFFFh

BA223 64 kwords DC0000h-DCFFFFh

BA222 64 kwords DB0000h-DBFFFFh

BA221 64 kwords DA0000h-DAFFFFh

BA220 64 kwords D90000h-D9FFFFh

BA219 64 kwords D80000h-D8FFFFh

BA218 64 kwords D70000h-D7FFFFh

BA217 64 kwords D60000h-D6FFFFh

BA216 64 kwords D50000h-D5FFFFh

BA215 64 kwords D40000h-D4FFFFh

BA214 64 kwords D30000h-D3FFFFh

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 13 -

NOR FLASH MEMORY

Table 3-2. Bottom Boot Block Address Table

Bank Block Block Size (x16) Address Range

Bank 13

BA213 64 kwords D20000h-D2FFFFh

BA212 64 kwords D10000h-D1FFFFh

BA211 64 kwords D00000h-D0FFFFh

Bank 12

BA210 64 kwords CF0000h-CFFFFFh

BA209 64 kwords CE0000h-CEFFFFh

BA208 64 kwords CD0000h-CDFFFFh

BA207 64 kwords CC0000h-CCFFFFh

BA206 64 kwords CB0000h-CBFFFFh

BA205 64 kwords CA0000h-CAFFFFh

BA204 64 kwords C90000h-C9FFFFh

BA203 64 kwords C80000h-C8FFFFh

BA202 64 kwords C70000h-C7FFFFh

BA201 64 kwords C60000h-C6FFFFh

BA200 64 kwords C50000h-C5FFFFh

BA199 64 kwords C40000h-C4FFFFh

BA198 64 kwords C30000h-C3FFFFh

BA197 64 kwords C20000h-C2FFFFh

BA196 64 kwords C10000h-C1FFFFh

BA195 64 kwords C00000h-C0FFFFh

Bank 11

BA194 64 kwords BF0000h-BFFFFFh

BA193 64 kwords BE0000h-BEFFFFh

BA192 64 kwords BD0000h-BDFFFFh

BA191 64 kwords BC0000h-BCFFFFh

BA190 64 kwords BB0000h-BBFFFFh

BA189 64 kwords BA0000h-BAFFFFh

BA188 64 kwords B90000h-B9FFFFh

BA187 64 kwords B80000h-B8FFFFh

BA186 64 kwords B70000h-B7FFFFh

BA185 64 kwords B60000h-B6FFFFh

BA184 64 kwords B50000h-B5FFFFh

BA183 64 kwords B40000h-B4FFFFh

BA182 64 kwords B30000h-B3FFFFh

BA181 64 kwords B20000h-B2FFFFh

BA180 64 kwords B10000h-B1FFFFh

BA179 64 kwords B00000h-B0FFFFh

Bank 10

BA178 64 kwords AF0000h-AFFFFFh

BA177 64 kwords AE0000h-AEFFFFh

BA176 64 kwords AD0000h-ADFFFFh

BA175 64 kwords AC0000h-ACFFFFh

BA174 64 kwords AB0000h-ABFFFFh

BA173 64 kwords AA0000h-AAFFFFh

BA172 64 kwords A90000h-A9FFFFh

BA171 64 kwords A80000h-A8FFFFh

BA170 64 kwords A70000h-A7FFFFh

BA169 64 kwords A60000h-A6FFFFh

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 14 -

NOR FLASH MEMORY

Table 3-2. Bottom Boot Block Address Table

Bank Block Block Size (x16) Address Range

Bank 10

BA168 64 kwords A50000h-A5FFFFh

BA167 64 kwords A40000h-A4FFFFh

BA166 64 kwords A30000h-A3FFFFh

BA165 64 kwords A20000h-A2FFFFh

BA164 64 kwords A10000h-A1FFFFh

BA163 64 kwords A00000h-A0FFFFh

Bank 9

BA162 64 kwords 9F0000h-9FFFFFh

BA161 64 kwords 9E0000h-9EFFFFh

BA160 64 kwords 9D0000h-9DFFFFh

BA159 64 kwords 9C0000h-9CFFFFh

BA158 64 kwords 9B0000h-9BFFFFh

BA157 64 kwords 9A0000h-9AFFFFh

BA156 64 kwords 990000h-99FFFFh

BA155 64 kwords 980000h-98FFFFh

BA154 64 kwords 970000h-97FFFFh

BA153 64 kwords 960000h-96FFFFh

BA152 64 kwords 950000h-95FFFFh

BA151 64 kwords 940000h-94FFFFh

BA150 64 kwords 930000h-93FFFFh

BA149 64 kwords 920000h-92FFFFh

BA148 64 kwords 910000h-91FFFFh

BA147 64 kwords 900000h-90FFFFh

Bank 8

BA146 64 kwords 8F0000h-8FFFFFh

BA145 64 kwords 8E0000h-8EFFFFh

BA144 64 kwords 8D0000h-8DFFFFh

BA143 64 kwords 8C0000h-8CFFFFh

BA142 64 kwords 8B0000h-8BFFFFh

BA141 64 kwords 8A0000h-8AFFFFh

BA140 64 kwords 890000h-89FFFFh

BA139 64 kwords 880000h-88FFFFh

BA138 64 kwords 870000h-87FFFFh

BA137 64 kwords 860000h-86FFFFh

BA136 64 kwords 850000h-85FFFFh

BA135 64 kwords 840000h-84FFFFh

BA134 64 kwords 830000h-83FFFFh

BA133 64 kwords 820000h-82FFFFh

BA132 64 kwords 810000h-81FFFFh

BA131 64 kwords 800000h-80FFFFh

Bank 7

BA130 64 kwords 7F0000h-7FFFFFh

BA129 64 kwords 7E0000h-7EFFFFh

BA128 64 kwords 7D0000h-7DFFFFh

BA127 64 kwords 7C0000h-7CFFFFh

BA126 64 kwords 7B0000h-7BFFFFh

BA125 64 kwords 7A0000h-7AFFFFh

BA124 64 kwords 790000h-79FFFFh

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 15 -

NOR FLASH MEMORY

Table 3-2. Bottom Boot Block Address Table

Bank Block Block Size (x16) Address Range

Bank 7

BA123 64 kwords 780000h-78FFFFh

BA122 64 kwords 770000h-77FFFFh

BA121 64 kwords 760000h-76FFFFh

BA120 64 kwords 750000h-75FFFFh

BA119 64 kwords 740000h-74FFFFh

BA118 64 kwords 730000h-73FFFFh

BA117 64 kwords 720000h-72FFFFh

BA116 64 kwords 710000h-71FFFFh

BA115 64 kwords 700000h-70FFFFh

Bank 6

BA114 64 kwords 6F0000h-6FFFFFh

BA113 64 kwords 6E0000h-6EFFFFh

BA112 64 kwords 6D0000h-6DFFFFh

BA111 64 kwords 6C0000h-6CFFFFh

BA110 64 kwords 6B0000h-6BFFFFh

BA109 64 kwords 6A0000h-6AFFFFh

BA108 64 kwords 690000h-69FFFFh

BA107 64 kwords 680000h-68FFFFh

BA106 64 kwords 670000h-67FFFFh

BA105 64 kwords 660000h-66FFFFh

BA104 64 kwords 650000h-65FFFFh

BA103 64 kwords 640000h-64FFFFh

BA102 64 kwords 630000h-63FFFFh

BA101 64 kwords 620000h-62FFFFh

BA100 64 kwords 610000h-61FFFFh

BA99 64 kwords 600000h-60FFFFh

Bank 5

BA98 64 kwords 5F0000h-5FFFFFh

BA97 64 kwords 5E0000h-5EFFFFh

BA96 64 kwords 5D0000h-5DFFFFh

BA95 64 kwords 5C0000h-5CFFFFh

BA94 64 kwords 5B0000h-5BFFFFh

BA93 64 kwords 5A0000h-5AFFFFh

BA92 64 kwords 590000h-59FFFFh

BA91 64 kwords 580000h-58FFFFh

BA90 64 kwords 570000h-57FFFFh

BA89 64 kwords 560000h-56FFFFh

BA88 64 kwords 550000h-55FFFFh

BA87 64 kwords 540000h-54FFFFh

BA86 64 kwords 530000h-53FFFFh

BA85 64 kwords 520000h-52FFFFh

BA84 64 kwords 510000h-51FFFFh

BA83 64 kwords 500000h-50FFFFh

Bank 4

BA82 64 kwords 4F0000h-4FFFFFh

BA81 64 kwords 4E0000h-4EFFFFh

BA80 64 kwords 4D0000h-4DFFFFh

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 16 -

NOR FLASH MEMORY

Table 3-2. Bottom Boot Block Address Table

Bank Block Block Size (x16) Address Range

Bank 4

BA79 64 kwords 4C0000h-4CFFFFh

BA78 64 kwords 4B0000h-4BFFFFh

BA77 64 kwords 4A0000h-4AFFFFh

BA76 64 kwords 490000h-49FFFFh

BA75 64 kwords 480000h-48FFFFh

BA74 64 kwords 470000h-47FFFFh

BA73 64 kwords 460000h-46FFFFh

BA72 64 kwords 450000h-45FFFFh

BA71 64 kwords 440000h-44FFFFh

BA70 64 kwords 430000h-43FFFFh

BA69 64 kwords 420000h-42FFFFh

BA68 64 kwords 410000h-41FFFFh

BA67 64 kwords 400000h-40FFFFh

Bank 3

BA66 64 kwords 3F0000h-3FFFFFh

BA65 64 kwords 3E0000h-3EFFFFh

BA64 64 kwords 3D0000h-3DFFFFh

BA63 64 kwords 3C0000h-3CFFFFh

BA62 64 kwords 3B0000h-3BFFFFh

BA61 64 kwords 3A0000h-3AFFFFh

BA60 64 kwords 390000h-39FFFFh

BA59 64 kwords 380000h-38FFFFh

BA58 64 kwords 370000h-37FFFFh

BA57 64 kwords 360000h-36FFFFh

BA56 64 kwords 350000h-35FFFFh

BA55 64 kwords 340000h-34FFFFh

BA54 64 kwords 330000h-33FFFFh

BA53 64 kwords 320000h-32FFFFh

BA52 64 kwords 310000h-31FFFFh

BA51 64 kwords 300000h-30FFFFh

Bank 2

BA50 64 kwords 2F0000h-2FFFFFh

BA49 64 kwords 2E0000h-2EFFFFh

BA48 64 kwords 2D0000h-2DFFFFh

BA47 64 kwords 2C0000h-2CFFFFh

BA46 64 kwords 2B0000h-2BFFFFh

BA45 64 kwords 2A0000h-2AFFFFh

BA44 64 kwords 290000h-29FFFFh

BA43 64 kwords 280000h-28FFFFh

BA42 64 kwords 270000h-27FFFFh

BA41 64 kwords 260000h-26FFFFh

BA40 64 kwords 250000h-25FFFFh

BA39 64 kwords 240000h-24FFFFh

BA38 64 kwords 230000h-23FFFFh

BA37 64 kwords 220000h-22FFFFh

BA36 64 kwords 210000h-21FFFFh

BA35 64 kwords 200000h-20FFFFh

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 17 -

NOR FLASH MEMORY

Table 3-2. Bottom Boot Block Address Table

Table 3-2-1. OTP Block Addresses

After entering OTP Block, any issued addresses should be in the range of OTP block address.

Bank Block Block Size (x16) Address Range

Bank 1

BA34 64 kwords 1F0000h-1FFFFFh

BA33 64 kwords 1E0000h-1EFFFFh

BA32 64 kwords 1D0000h-1DFFFFh

BA31 64 kwords 1C0000h-1CFFFFh

BA30 64 kwords 1B0000h-1BFFFFh

BA29 64 kwords 1A0000h-1AFFFFh

BA28 64 kwords 190000h-19FFFFh

BA27 64 kwords 180000h-18FFFFh

BA26 64 kwords 170000h-17FFFFh

BA25 64 kwords 160000h-16FFFFh

BA24 64 kwords 150000h-15FFFFh

BA23 64 kwords 140000h-14FFFFh

BA22 64 kwords 130000h-13FFFFh

BA21 64 kwords 120000h-12FFFFh

BA20 64 kwords 110000h-11FFFFh

BA19 64 kwords 100000h-10FFFFh

Bank 0

BA18 64 kwords 0F0000h-0FFFFFh

BA17 64 kwords 0E0000h-0EFFFFh

BA16 64 kwords 0D0000h-0DFFFFh

BA15 64 kwords 0C0000h-0CFFFFh

BA14 64 kwords 0B0000h-0BFFFFh

BA13 64 kwords 0A0000h-0AFFFFh

BA12 64 kwords 090000h-09FFFFh

BA11 64 kwords 080000h-08FFFFh

BA10 64 kwords 070000h-07FFFFh

BA9 64 kwords 060000h-06FFFFh

BA8 64 kwords 050000h-05FFFFh

BA7 64 kwords 040000h-04FFFFh

BA6 64 kwords 030000h-03FFFFh

BA5 64 kwords 020000h-02FFFFh

BA4 64 kwords 010000h-01FFFFh

BA3 16 kwords 00C000h-00FFFFh

BA2 16 kwords 008000h-00BFFFh

BA1 16 kwords 004000h-007FFFh

BA0 16 kwords 000000h-003FFFh

OTP

Block Address

A23 ~ A8 Block Size (x16) Address Range*

0000h 512 words 000000h-0001FFh

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 18 -

NOR FLASH MEMORY

PRODUCT INSTRUCTION

The K8C54(55)15E is an 256Mbit (268,435,456 bits) NOR-type Burst Flash memory. The device features 1.8V single voltage power supply

operating within the range of 1.7V to 1.95V. The device is programmed by using the Channel Hot Electron (CHE) injection mechanism which

is used to program EPROMs. The device is erased electrically by using Fowler-Nordheim tunneling mechanism. To provide highly flexible

erase and program capability, the device adapts a block memory architecture that divides its memory array into 259 blocks (64-Kword x255,

16-Kword x 4, ). Programming is done in units of 16 bits (Word). All bits of data in one or multiple blocks can be erased when the device exe-

cutes the erase operation. To prevent the device from accidental erasing or over-writing the programmed data, 259 memory blocks can be

hardware protected. Regarding read access time, at 66MHz, the K8C5415E provides a burst access of 11ns with initial access times of 100ns

at 30pF. At 83MHz, the K8C5415E provides a burst access of 9ns with initial access times of 100ns at 30pF. At 108MHz, the K8C5515E pro-

vides a burst access of 7ns with initial access times of 100ns at 30pF. At 133MHz, the K8C5515E provides a burst access of 6ns with initial

access times of 100ns at 30pF. The command set of K8C54(55)15E is compatible with standard Flash devices. The device uses Chip Enable

(CE), Write Enable (WE), Output Enable (OE) to control asynchronous read and write operation. For burst operations, the device additionally

requires Ready (RDY) and Clock (CLK). Device operations are executed by selective command codes. The command codes to be combined

with addresses and data are sequentially written to the command registers using microprocessor write timing. The command codes serve as

inputs to an internal state machine which controls the program/erase circuitry. Register contents also internally latch addresses and data nec-

essary to execute the program and erase operations. The K8C54(55)15E is implemented with Internal Program/Erase Routines to execute the

program/erase operations. The Internal Program/Erase Routines are invoked by program/erase command sequences. The Internal Program

Routine automatically programs and verifies data at specified addresses. The Internal Erase Routine automatically pre-programs the memory

cell which is not programmed and then executes the erase operation. The K8C54(55)15E has means to indicate the status of completion of

program/erase operations. The status can be indicated via Data polling of DQ7, or the Toggle bit (DQ6). Once the operations have been com-

pleted, the device automatically resets itself to the read mode. The device requires only 35 mA as burst and asynchronous mode read current

and 25 mA for program/erase operations.

Table 4. Device Bus Operations

NOTE

L=VIL (Low), H=VIH (High), X=Don’t Care.

Operation CE OE WE A0-23 DQ0-15 RESET CLK AVD

Asynchronous Read Operation L L H Add In I/O H L L

Write L H Add In I/O H L X

Standby H X X X High-Z H X X

Hardware Reset X X X X High-Z L X X

Load Initial Burst Address L H H Add In X H

Burst Read Operation L L H X Burst

DOUT HH

Terminate Burst Read Cycle H X X X High-Z H X X

Terminate Burst Read Cycle via RESET X X X X High-Z L X X

Terminate Current Burst Read Cycle and Start

New Burst Read Cycle L H H Add In I/O H

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 19 -

NOR FLASH MEMORY

COMMAND DEFINITIONS

The K8C54(55)15E operates by selecting and executing its operational modes. Each operational mode has its own command set. In order to

select a certain mode, a proper command with specific address and data sequences must be written into the command register. Writing incor-

rect information which include address and data or writing an improper command will reset the device to the read mode. The defined valid reg-

ister command sequences are stated in Table 5.

Table 5. Command Sequences

Command Definitions Cycle 1st Cycle 2nd Cycle 3rd Cycle 4th Cycle 5th Cycle 6th Cycle

Asynchronous Read Add 1R A

Data RD

Reset(Note 5) Add 1XXXH

Data F0H

Autoselect

Manufacturer ID(Note 6)

Add 4555H 2AAH (DA)555H (DA)X00H

Data AAH 55H 90H ECH

Autoselect

Device ID(Note 6)

Add

555H 2AAH (DA)555H (DA)X01H

Data AAH 55H 90H Note6

Autoselect

Block Protection Verify(Note 7)

Add 4555H 2AAH (BA)555H (BA)X02H

Data AAH 55H 90H 00H / 01H

Autoselect

Handshaking(Note 6, 8)

Add 4555H 2AAH (DA)555H (DA)X03H

D a t a A A H 5 5 H 9 0 H 0 H / 1 H

Program

Add

555H 2AAH 555H PA

Data AAH 55H A0H PD

Unlock Bypass Add 3555H 2AAH 555H

Data AAH 55H 20H

Unlock Bypass Program(Note 9) Add 2XXX PA

Data A0H PD

Unlock Bypass Block Erase(Note 9)

Add

XXX BA

Data 80H 30H

Unlock Bypass Chip Erase(Note 9) Add 2XXXH XXXH

Data 80H 10H

Unlock Bypass Reset Add 2XXXH XXXH

Data 90H 00H

Chip Erase

Add

555H 2AAH 555H 555H 2AAH 555H

Data AAH 55H 80H AAH 55H 10H

Block Erase Add 6555H 2AAH 555H 555H 2AAH BA

Data AAH 55H 80H AAH 55H 30H

Erase Suspend (Note 10) Add 1(DA)XXXH

Data B0H

Erase Resume (Note 11)

Add

(DA)XXXH

Data 30H

Program Suspend (Note12) Add 1(DA)XXXH

Data B0H

Program Resume (Note11) Add 1(DA)XXXH

Data 30H

Block Protection/Unprotection (Note 13)

Add

XXX XXX ABP

Data 60H 60H 60H

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 20 -

NOR FLASH MEMORY

Table 5. Command Sequences (Continued)

NOTE

1) RA : Read Address , PA : Program Address, RD : Read Data, PD : Program Data , BA : Block Address (A23 ~ A14), DA : Bank Address (A23 ~ A20)

ABP : Address of the block to be protected or unprotected , DI :Die revision ID, CR : Configuration Register Setting,

WBL : Write Buffer Location, WC : Word Count

2) The 4th cycle data of autoselect mode and RD are output data. The others are input data.

3) Data bits DQ15–DQ8 are don’t care in command sequences, except for RD, PD and Device ID.

4) Unless otherwise noted, address bits A23–A11 are don’t cares.

5) The reset command is required to return to read mode.

If a bank entered the autoselect mode during the erase suspend mode, writing the reset command returns that bank to the erase suspend mode.

If a bank entered the autoselect mode during the program suspend mode, writing the reset command returns that bank to the program suspend mode.

If DQ5 goes high during the program or erase operation, writing the reset command returns that bank to read mode or erase suspend mode if that

bank was in erase suspend mode.

6) The 3rd and 4th cycle bank address of autoselect mode must be same.

Device ID Data : "2206H" for Top Boot Block Device, "2207H" for Bottom Boot Block Device

7) Normal Block Protection Verify : 00H for an unprotected block and 01H for a protected block.

OTP Block Protect verify (with OTP Block Address after Entering OTP Block) : 00H for unlocked, and 01H for locked.

8) 0H for handshaking, 1H for non-handshaking

9) The unlock bypass command sequence is required prior to this command sequence.

10) The system may read and program in non-erasing blocks when in the erase suspend mode.

The system may enter the autoselect mode when in the erase suspend mode.

The erase suspend command is valid only during a block erase operation, and requires the bank address.

11) The erase/program resume command is valid only during the erase/program suspend mode, and requires the bank address.

12) This mode is used only to enable Data Read by suspending the Program operation.

13) Set ABP(Address of the block to be protected or unprotected) as either A6 = VIH, A1 = VIH and A0 = VIL for unprotected or A6 = VIL, A1 = VIH

and A0 = VIL for protected.

14) Command is valid when the device is in Read mode or Autoselect mode.

15) For Buffer Program, Firstly Enter "Write to Buffer" Command sequence and then Enter Block Address and Word Count which is the number of word

data will be programmed. Word Count is smaller than the number of data wanted to program by one, Example if 15 words are wanted to program

then WC (Word Count) is 14. After Entering Command, Enter PA/PD’s (Program Addresses/ Program Data). Finally Enter "Program buffer to Flash"

Command sequence, This starts a buffer program operation. This Device supports 32 words Buffer Program.

There is some caution points.

- The number of PA/PD’s which are entered must be same to WC+1

- PA’s which are entered must be same A23~A5 address bits because Buffer Address is A23~A5 address and decided by PA entered firstly.

- If PA which are entered isn’t same Buffer Address, then PA/PD which is entered may not be counted and not stored to Buffer.

- Overwrite for program buffer is also prohibited.

16) Command sequence resets device for next command after aborted write-to-buffer operation.

17) See "Set Burst Mode Configuration Register" for details.

18) On the third cycle, the data should be "C0h", address bits A10-A0 should be 101_0101_0101b, and address bits A18-A11 set the code to be

latched.

Command Definitions Cycle 1st Cycle 2nd Cycle 3rd Cycle 4th Cycle 5th Cycle 6th Cycle

CFI Query (Note 14)

Add 1(DA)X55H

Data 98H

Write to Buffer (Note 15) Add 3555H 2AAH BA BA PA WBL

Data AAH 55H 25H WC PD PD

Program buffer to Flash (Note 15) Add 1BA

Data 29H

Write to Buffer Abort Reset (Note 16)

Add

555H 2AAH XXX

Data AAH 55H F0H

Set Burst Mode Configuration Register (Note 17) Add 3555H 2AAH (CR)555H

Data AAH 55H C0H

Enter OTP Block Region Add 3555H 2AAH XXX

Data AAH 55H 70H

Exit OTP Block Region

Add 4555H 2AAH 555H XXX

Data AAH 55H 75H 00H

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 21 -

NOR FLASH MEMORY

DEVICE OPERATION

The device has inputs/outputs that accept both address and data information. To write a command or command sequence (which includes

programming data to the device and erasing blocks of memory), the system must drive CLK, WE and CE to VIL and OE to VIH when writing

commands or data.

The device provide the unlock bypass mode to save its program time for program operation. Unlike the standard program command sequence

which is comprised of four bus cycles, only two program cycles are required to program a word in the unlock bypass mode. One block, multi-

ple blocks, or the entire device can be erased. Table 3 indicates the address space that each block occupies. The device’s address space is

divided into sixteen banks: Bank 0 contains the boot/parameter blocks, and the other banks(from Bank 1 to 15) consist of uniform blocks. A

“bank address” is the address bits required to uniquely select a bank. Similarly, a “block address” is the address bits required to uniquely select

a block. ICC2 in the DC Characteristics table represents the active current specification for the write mode. The AC Characteristics section con-

tains timing specification tables and timing diagrams for write operations.

Read Mode

The device automatically enters to asynchronous read mode after device power-up. No commands are required to retrieve data in asynchro-

nous mode. After completing an Internal Program/Erase Routine, each bank is ready to read array data. The reset command is required to

return a bank to the read(or erase-suspend-read)mode if DQ5 goes high during an active program/erase operation, or if the bank is in the

autoselect mode.

The synchronous(burst) mode will automatically be enabled on the first rising edge on the CLK input while AVD is held low. That means

device enters from asynchronous read mode to burst read mode using CLK and AVD signal. When the burst read is terminated, the device

return to asynchronous read mode automatically.

Asynchronous Read Mode

For the asynchronous read mode a valid address should be asserted on A0-A23, while driving AVD and CE to VIL. WE should remain at VIH

. The data will appear on DQ0-DQ15. Since the memory array is divided into sixteen banks, each bank remains enabled for read access until

the command register contents are altered.

Address access time (tAA) is equal to the delay from valid addresses to valid output data. The chip enable access time(tCE) is the delay from

the falling edge of CE to valid data at the outputs. The output enable access time(tOE) is the delay from the falling edge of OE to valid data at

the output. To prevent the memory content from spurious altering during power transition, the initial state machine is set for reading array data

upon device power-up, or after a hardware reset.

Synchronous (Burst) Read Mode

The device is capable of continuous linear burst operation and linear burst operation of a preset length. For the burst mode, the system should

determine how many clock cycles are desired for the initial word(tIAA) of each burst access and what mode of burst operation is desired using

"Burst Mode Configuration Register" command sequences. See "Set Burst Mode Configuration" for further details. The status data also can be

read during burst read mode by using AVD signal with a bank address which is programming or erasing. This status data by synchronous

read mode can be output just once and then sychronous read mode will be terminated. To initiate the synchronous read again, a new address

and AVD pulse is needed after the host has completed status reads or the device has completed the program or erase operation.

Note that, after power up, the device enters asynchronous read mode. A19 determine the synchronous burst read mode by setting ’1’.

Continuous Linear Burst Read

The synchronous(burst) mode will automatically be enabled on the first rising edge on the CLK input while AVD is held low. Note that the

device is enabled for asynchronous mode when it first powers up. The initial word is output tIAA after the rising edge of the first CLK cycle. Sub-

sequent words are output tBA after the rising edge of each successive clock cycle, which automatically increase the internal address counter.

Note that the device has internal address boundary that occurs every 16 words. When the device is crossing the first word boundary, addi-

tional clock cycles are needed before data appears for the next address. The number of addtional clock cycle can vary from zero to fourteen

cycles, and the exact number of additional clock cycle depends on the starting address of burst read. The RDY output indicates this condition

to the system by pulsing low. The device will continue to output sequential burst data, wrapping around to address 000000h after it reaches

the highest addressable memory location until the system asserts CE high, RESET low or AVD low in conjunction with a new address.(See

Table 4.) The reset command does not terminate the burst read operation.

If the host system crosses the bank boundary while reading in burst mode, and the accessed bank is not programming or erasing, a additional

clock cycles are needed as previously mentioned. When it accesses the bank is programming or erasing, continuous burst read mode will be

terminated after status data output once.

8-, 16-Word Linear Burst Read

As well as the Continuous Linear Burst Mode, there are two(8 & 16 word) linear wrap & no-wrap mode, in which a fixed number of words are

read from consecutive addresses. In these modes, the addresses for burst read are determined by the group within which the starting

address falls. The groups are sized according to the number of words read in a single burst sequence for a given mode.(See Table. 6)

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 22 -

NOR FLASH MEMORY

Table 6. Burst Address Groups(Wrap mode)

As an example: In wrap mode case, if the starting address in the 8-word mode is 2h, the address range to be read would be 0-7h, and the

wrap burst sequence would be 2-3-4-5-6-7-0-1h. The burst sequence begins with the starting address written to the device, but wraps back to

the first address in the selected group. In a similar manner, 16-word wrap mode begin their burst sequence on the starting address written to

the device, and then wrap back to the first address in the selected address group.

In no-wrap mode case, if the starting address in the 8-word mode is 2h, the no-wrap burst sequence would be 2-3-4-5-6-7-8-9h. The burst

sequence begins with the starting address written to the device, and continue to the 8th address from starting address. In a similar manner,

16-word no-wrap mode begin their burst sequence on the starting address written to the device, and continue to the 16th address from starting

address. Also, when the address cross the word boundary in no-wrap mode, same number of additional clock cycles as continuous linear

mode is needed.

Programmable Wait State

The programmable wait state feature indicates to the device the number of additional clock cycles that must elapse after AVD is driven from

low to high for burst read mode. Upon power up, the number of total initial access cycles defaults to fourteen.

Handshaking

The handshaking feature allows the host system to simply monitor the RDY signal from the device to determine when the initial word of burst

data is ready to be read. To set the number of initial cycle for optimal burst mode, the host should use the programmable wait state configura-

tion.(See "Set Burst Mode Configuration Register" for details.) The rising edge of RDY after OE goes low indicates the initial word of valid

burst data. Using the autoselect command sequence the handshaking feature may be verified in the device.

Set Burst Mode Configuration Register

The device uses a configuration register to set the various burst parameters : the number of initial cycles for burst and burst read mode. The

burst mode configuration register must be set before the device enter burst mode.

The burst mode configuration register is loaded with a three-cycle command sequences. On the third cycle, the data should be C0h, address

bits A10-A0 should be 101_0101_0101b, and address bits A18-A11 set the code to be latched. The device will power up or after a hardware

reset with the default setting.

Table 7. Burst Mode Configuration Register Table

Note:

Initial wait state should be set according to it’s clock frequency. Table7 recommend the program wait state for each clock frequencies.

Not 100% tested

Burst Mode Group Size Group Address Ranges

8 word 8 words 0-7h, 8-Fh, 10-17h, ....

16 word 16words 0-Fh, 10-1Fh, 20-2Fh, ....

Address Bit Function Settings(Binary)

A19 Read Mode 1 = Synchronous Burst Read Mode

0 = Asynchronous Read Mode (default)

A18 RDY Active 1 = RDY active one clock cycle before data

0 = RDY active with data(default)

A17

Burst Read Mode

000 = Continuous(default)

001 = 8-word linear with wrap

010 = 16-word linear with wrap

011 = 8-word linear with no-wrap

100 = 16-word linear with no-wrap

101~111 = Reserve

A16

A15

A14

Programmable Wait State

0000 = Data is valid on the 4th active CLK edge after AVD transition to VIH(40MHz)

0001 = Data is valid on the 5th active CLK edge after AVD transition to VIH(50MHz)

0010 = Data is valid on the 6th active CLK edge after AVD transition to VIH(54/60MHz)

0011 = Data is valid on the 7th active CLK edge after AVD transition to VIH(66/70MHz)

0100 = Data is valid on the 8th active CLK edge after AVD transition to VIH(80MHz)

0101 = Data is valid on the 9th active CLK edge after AVD transition to VIH(83/90MHz)

0110 = Data is valid on the 10th active CLK edge after AVD transition to VIH(100MHz)

0111 = Data is valid on the 11th active CLK edge after AVD transition to VIH(108/110MHz)

1000 = Data is valid on the 12th active CLK edge after AVD transition to VIH(120MHz)

1001 = Data is valid on the 13th active CLK edge after AVD transition to VIH

1010 = Data is valid on the 14th active CLK edge after AVD transition to VIH(default, at 133MHz)

1011 = Data is valid on the 15th active CLK edge after AVD transition to VIH

1100~1111 = Reserve

A13

A12

A11

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 23 -

NOR FLASH MEMORY

Programmable Wait State Configuration

This feature informs the device the number of clock cycles that must elapse after AVD is driven from low to high before data will be available.

This value is determined by the input frequency of the device. Address bits A14-A11 determine the setting. (See Burst Mode Configuration

Register Table) The Programmable wait state setting instructs the device to set a particular number of clock cycles for the initial access in

burst mode. Note that hardware reset will set the wait state to the default setting, that is 14 initial cycles.

Burst Read Mode Setting

The device supports five different burst read modes : continuous linear mode, 8 and 16 word linear burst modes with wrap and 8 and 16 word

linear burst modes with no-wrap.

RDY Configuration

By default, the RDY pin will be high whenever there is valid data on the output. The device can be set so that RDY goes active one data cycle

before active data. Adddress bit A18 determines this setting. The RDY pin behaves same way in word boundary crossing case.

Table 8. Burst Address Sequences

Autoselect Mode

By writing the autoselect command sequences to the system, the device enters the autoselect mode. This mode can be read only by asyn-

chronous read mode. The system can then read autoselect codes from the internal register(which is separate from the memory array). Stan-

dard asynchronous read cycle timings apply in this mode. The device offers the Autoselect mode to identify manufacturer and device type by

reading a binary code. In addition, this mode allows the host system to verify the block protection or unprotection. Table 5 shows the address

and data requirements. The autoselect command sequence may be written to an address within a bank that is in the read mode, erase-sus-

pend-read mode or program-suspend-read mode. The autoselect command may not be written while the device is actively programming or

erasing in the device. The autoselect command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle

that contains the address and the autoselect command. Note that the block address is needed for the verification of block protection. The sys-

tem may read at any address within the same bank any number of times without initiating another autoselect command sequence. And the

burst read should be prohibited during Autoselect Mode. To terminate the autoselect operation, write Reset command(F0H) into the command

Table 9. Autoselect Mode Description

Standby Mode

When the CE inputs is held at VCC ± 0.2V, and the system is not reading or writing, the device enters Stand-by mode to minimize the power

consumption. In this mode, the device outputs are placed in the high impedence state, independent of the OE input. When the device is in

either of these standby modes, the device requires standard access time (tCE ) for read access before it is ready to read data. If the device is

deselected during erasure or programming, the device draws active current until the operation is completed. ICC5 in the DC Characteristics

Start

Addr.

Burst Address Sequence(Decimal)

Continuous Burst 8-word Burst 16-word Burst

Wrap

0 0-1-2-3-4-5-6... 0-1-2-3-4-5-6-7 0-1-2-3 ... -D-E-F

1 1-2-3-4-5-6-7... 1-2-3-4-5-6-7-0 1-2-3-4 ... -E-F-0

2 2-3-4-5-6-7-8... 2-3-4-5-6-7-0-1 2-3-4-5 ... -F-0-1

No-wrap

0 0-1-2-3-4-5-6... 0-1-2-3-4-5-6-7 0-1-2-3 ... -D-E-F

1 1-2-3-4-5-6-7... 1-2-3-4-5-6-7-8 1-2-3-4 ... -E-F-10

2 2-3-4-5-6-7-8... 2-3-4-5-6-7-8-9 2-3-4-5 ... -F-10-11

Description Address Read Data

Manufacturer ID (DA) + 00H ECH

Device ID (DA) + 01H 2206H(Top Boot Block), 2207H(Bottom Boot Block)

Block Protection/Unprotection (BA) + 02H 01H (protected), 00H (unprotected)

Handshaking (DA) + 03H 0H : handshaking, 1H : non-handshaking

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 24 -

NOR FLASH MEMORY

table represents the standby current specification.

Autosleep Mode

The device features Automatic Sleep Mode to minimize the device power consumption during both asynchronous and burst mode. When

addresses remain stable for tAA+60ns, the device automatically enables this mode. The Automatic sleep mode is depends on the CE, WE and

OE signal, so CE, WE and OE signals are held at any state. In a sleep mode, output data is latched and always available to the system. When

OE is active, the device provides new data without wait time. Automatic sleep mode current is equal to standby mode current.

Output Disable Mode

When the OE input is at VIH , output from the device is disabled. The outputs are placed in the high impedance state.

Block Protection & Unprotection

To protect the block from accidental writes, the block protection/unprotection command sequence is used. On power up, all blocks in the

device are protected. To unprotect a block, the system must write the block protection/unprotection command sequence. The first two cycles

are written: addresses are don’t care and data is 60h. Using the third cycle, the block address (ABP) and command (60h) is written, while

specifying with addresses A6, A1 and A0 whether that block should be protected (A6 = VIL, A1 = VIH, A0 = VIL) or unprotected (A6 = VIH, A1 =

VIH, A0 = VIL). After the third cycle, the system can continue to protect or unprotect additional cycles, or exit the sequence by writing F0h (reset

command).

The device offers three types of data protection at the block level:

• The block protection/unprotection command sequence disables or re-enables both program and erase operations in any block.

• When WP is at VIL, the two outermost blocks are protected.

• When VPP is at VIL, all blocks are protected.

Note that user never float the Vpp and WP, that is, Vpp is always connected with VIH, VIL or VID and WP is VIH or VIL.

Hardware Reset

The device features a hardware method of resetting the device by the RESET input. When the RESET pin is held low(VIL) for at least a period

of tRP, the device immediately terminates any operation in progress, tristates all outputs, and ignores all read/write commands for the duration

of the RESET pulse. The device also resets the internal state machine to asynchronous read mode. To ensure data integrity, the interrupted

operation should be reinitiated once the device is ready to accept another command sequence. The RESET pin may be tied to the system

reset pin. If a system reset occurs during the Internal Program or Erase Routine, the device will be automatically reset to the asynchronous

read mode; this will enable the systems microprocessor to read the boot-up firmware from the Flash memory. If RESET is asserted during a

program or erase operation, the device requires a time of tREADY (during Internal Routines) before the device is ready to read data again. If

RESET is asserted when a program or erase operation is not executing, the reset operation is completed within a time of tREADY (not during

Internal Routines). tRH is needed to read data after RESET returns to VIH. Refer to the AC Characteristics tables for RESET parameters and

to Figure 10 for the timing diagram. When RESET is at logic high, the device is in standard operation. When RESET transitions from logic-low

to logic-high, the device resets all blocks to locked and defaults to the read array mode.

Software Reset

The reset command provides that the bank is reseted to read mode, erase-suspend-read mode or program-suspend-read mode. The

addresses are in Don’t Care state. The reset command may be written between the sequence cycles in an erase command sequence before

erasing begins, or in an program command sequence before programming begins. If the device begins erasure or programming, the reset

command is ignored until the operation is completed. If the program command sequence is written to a bank that is in the Erase Suspend

mode, writing the reset command returns that bank to the erase-suspend-read mode. The reset command valid between the sequence cycles

in an autoselect command sequence. In an autoselect mode, the reset command must be written to return to the read mode. If a bank entered

the autoselect mode while in the Erase Suspend mode, writing the reset command returns that bank to the erase-suspend-read mode. Also, if

a bank entered the autoselect mode while in the Program Suspend mode, writing the reset command returns that bank to the program-sus-

pend-read mode. If DQ5 goes high during a program or erase operation, writing the reset command returns the banks to the read mode. (or

erase-suspend-read mode if the bank was in Erase Suspend)

Program

The K8C54(55)15E can be programmed in units of a word. Programming is writing 0's into the memory array by executing the Internal Pro-

gram Routine. In order to perform the Internal Program Routine, a four-cycle command sequence is necessary. The first two cycles are unlock

cycles. The third cycle is assigned for the program setup command. In the last cycle, the address of the memory location and the data to be

programmed at that location are written. The device automatically generates adequate program pulses and verifies the programmed cell mar-

gin by the Internal Program Routine. During the execution of the Routine, the system is not required to provide further controls or timings. Dur-

ing the Internal Program Routine, commands written to the device will be ignored.

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 25 -

NOR FLASH MEMORY

Note that a hardware reset during a program operation will cause data corruption at the corresponding location.

Accelerated Program

The device provides accelerated program operations through the Vpp input. Using this mode, faster manufacturing throughput at the factory is

possible. When VID is asserted on the Vpp input, the device automatically enters the Unlock Bypass mode, temporarily unprotects any pro-

tected blocks, and uses the higher voltage on the input to reduce the time required for program operations. In accelerated program mode, the

system would use a two-cycle program command sequence for only a word program. By removing VID returns the device to normal operation

mode.

Note that Read While Accelerated Program and Program suspend mode are not guaranteed.

• Program/Erase cycling must be limited below 100cycles for optimum performance.

• Ambient temperature requirements : TA = 30°C±10°C

Write Buffer Programming

Write Buffer Programming allows the system write to a maximum of 32 words in one programming operation. This results in faster effective

programming time than the standard programming algorithms. The Write Buffer Programming command sequence is initi-ated by first writing

two unlock cycles. This is followed by a third write cycle containing the Write Buffer Load command written at the block address in which pro-

gramming will occur. The fourth cycle writes the block address and the number of word locations, minus one, to be programmed. For example,

if the system will program 19 unique address locations, then 12h should be written to the device. This tells the device how many write buffer

addresses will be loaded with data. The number of locations to program cannot exceed the size of the write buffer or the operation will abort.

The fifth cycle writes the first address location and data to be programmed. The write-buffer-page is selected by address bits A23(max.) ~

A5 entered at fifth cycle. All subsequent address/ data pairs must fall within the selected write-buffer-page, so that all subsequent

addresses must have the same address bit A23(max.) ~ A5 as those entered at fifth cycle. Write buffer locations may be loaded in

any order.

Once the specified number of write buffer locations have been loaded, the system must then write the "Program Buffer to Flash" com mand at

the block address. Any other command address/data combination aborts the Write Buffer Programming operation. The device then begins

programming. Data polling should be used while monitoring the last address location loaded into the write buffer. DQ7, DQ6, DQ5, and DQ1

should be monitored to determine the device status during Write Buffer Programming. The write-buffer programming operation can be sus-

pended using the standard program suspend/resume commands. Upon successful completion of the Write Buffer Programming operation, the

device is ready to execute the next command. Note also that an address loaction cannot be loaded more than once into the write-

buffer-page.

The Write Buffer Programming Sequence can be aborted in the following ways:

• Loading a value that is greater than the buffer size(32-words) during then number of word locations to Program step.

(In case, WC > 1FH @Table5 )

• The number of Program address/data pairs entered is different to the number of word locations initially defined with WC (@Table5)

• Writing a Program address to have a different write-buffer-page with selected write-buffer-page

( Address bits A23(max) ~ A5 are different)

• Writing non-exact "Program Buffer to Flash" command

The abort condition is indicated by DQ1 = 1, DQ7 = DATA (for the last address location loaded), DQ6 = toggle, and DQ5=0. A "Write-to-Buffer-

Abort Reset" command sequence must be written to reset the device for the next operation. Note that the third cycle of Write-to-Buffer-Abort

Reset command sequence is required when using Write-Buffer-Programming features in Unlock Bypass mode. And from the third cycle to the

last cycle of Write to Buffer command is also required when using Write-Buffer-Programming features in Unlock Bypass mode. A bit cannot be

programmed from “0” back to a “1.” Attempting to do so may cause the device to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indi-

cate the operation was successful. However, a succeeding read will show that the data is still “0.” Only erase operations can convert a “0” to

a “1."

Accelerated Write Buffer Programming

The device provides accelerated Write Buffer Program operations through the Vpp input. Using this mode, faster manufacturing throughput at

the factory is possible. When VID is asserted on the Vpp input, the device temporarily unprotects any protected blocks, and uses the higher

voltage on the input to reduce the time required for program operations. In accelerated Write Buffer Program mode, the system must enter

"Write to Buffer" and "Program Buffer to Flash" command sequence to be same as them of normal Write Buffer Programming and only can

reduce the program time. Note that the third cycle of "Write to Buffer Abort Reset" command sequence is required in an Accelerated mode.

Note that Read While Accelerated Write Buffer Program and Program suspend mode are not guaranteed.

• Program/Erase cycling must be limited below 100cycles for optimum performance.

• Ambient temperature requirements : TA = 30°C±10°C

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 26 -

NOR FLASH MEMORY

Chip Erase

To erase a chip is to write 1′s into the entire memory array by executing the Internal Erase Routine. The Chip Erase requires six bus cycles to

write the command sequence. The erase set-up command is written after first two "unlock" cycles. Then, there are two more write cycles prior

to writing the chip erase command. The Internal Erase Routine automatically pre-programs and verifies the entire memory for an all zero data

pattern prior to erasing. The automatic erase begins on the rising edge of the last WE pulse in the command sequence and terminates when

DQ7 is "1". After that the device returns to the read mode.

Block Erase

To erase a block is to write 1′s into the desired memory block by executing the Internal Erase Routine. The Block Erase requires six bus cycles

to write the command sequence shown in Table 5. After the first two "unlock" cycles, the erase setup command (80H) is written at the third

cycle. Then there are two more "unlock" cycles followed by the Block Erase command. The Internal Erase Routine automatically pre-programs

and verifies the entire memory prior to erasing it. The block address is latched on the rising edge of AVD , while the Block Erase command is

latched on the rising edge of WE. Multiple blocks can be erased sequentially by writing the sixth bus-cycle. Upon completion of the last cycle

for the Block Erase, additional block address and the Block Erase command (30H) can be written to perform the Multi-Block Erase. For the

Multi-Block Erase, only sixth cycle(block address and 30H) is needed.(Similarly, only second cycle is needed in unlock bypass block erase.)

An 50us (typical) "time window" is required between the Block Erase command writes. The Block Erase command must be written within the

50us "time window", otherwise the Block Erase command will be ignored. The 50us "time window" is reset when the falling edge of the WE

occurs within the 50us of "time window" to latch the Block Erase command. During the 50us of "time window", any command other than the

Block Erase or the Erase Suspend command written to the device will reset the device to read mode. After the 50 us of "time window", the

Block Erase command will initiate the Internal Erase Routine to erase the selected blocks. Any Block Erase address and command following

the exceeded "time window" may or may not be accepted. No other commands will be recognized except the Erase Suspend command during

Block Erase operation.

Unlock Bypass

The K8C54(55)15E provides the unlock bypass mode to save its operation time. This mode is possible for program, block erase and chip

erase operation. There are two methods to enter the unlock bypass mode. The mode is invoked by the unlock bypass command sequence or

the assertion of VID on VPP pin. Unlike the standard program/erase command sequence that contains four bus cycles, the unlock bypass pro-

gram/erase command sequence comprises only two bus cycles. The unlock bypass mode is engaged by issuing the unlock bypass command

sequence which is comprised of three bus cycles. Writing first two unlock cycles is followed by a third cycle containing the unlock bypass com-

mand (20H). Once the device is in the unlock bypass mode, the unlock bypass program/erase command sequence is necessary. The unlock

bypass program command sequence is comprised of only two bus cycles; writing the unlock bypass program command (A0H) is followed by

the program address and data. This command sequence is the only valid one for programming the device in the unlock bypass mode. Also,

The unlock bypass erase command sequence is comprised of two bus cycles; writing the unlock bypass block erase command(80H-30H) or

writing the unlock bypass chip erase command(80H-10H). This command sequences are the only valid ones for erasing the device in the

unlock bypass mode. The unlock bypass reset command sequence is the only valid command sequence to exit the unlock bypass mode. The

unlock bypass reset command sequence consists of two bus cycles. The first cycle must contain the data (90H). The second cycle contains

only the data (00H). Then, the device returns to the read mode.

To enter the unlock bypass mode in hardware level, the VID also can be used. By assertion VID on the VPP pin, the device enters the unlock

bypass mode. Also, the all blocks are temporarily unprotected when the device using the VID for unlock bypass mode. To exit the unlock

bypass mode, just remove the asserted VID from the VPP pin.(Note that user never float the Vpp, that is, Vpp is always connected with VIH, VIL

or VID.).

Erase Suspend / Resume

The Erase Suspend command interrupts the Block Erase to read or program data in a block that is not being erased. Also, it is possible to pro-

tect or unprotect of the block that is not being erased in erase suspend mode. The Erase Suspend command is only valid during the Block

Erase operation including the time window of 50 us. The Erase Suspend command is not valid while the Chip Erase or the Internal Program

Routine sequence is running. When the Erase Suspend command is written during a Block Erase operation, the device requires a maximum

of 20 us(recovery time) to suspend the erase operation. Therefore system must wait for 20us(recovery time) to read the data from the bank

which include the block being erased. Otherwise, system can read the data immediately from a bank which don’t include the block being

erased without recovery time(max. 20us) after Erase Suspend command. And, after the maximum 20us recovery time, the device is availble

for programming data in a block that is not being erased. But, when the Erase Suspend command is written during the block erase time win-

dow (50 us) , the device immediately terminates the block erase time window and suspends the erase operation. The system may also write

the autoselect command sequence when the device is in the Erase Suspend mode. When the Erase Resume command is executed, the

Block Erase operation will resume. When the Erase Suspend or Erase Resume command is executed, the addresses are in Don't Care state.

In erase suspend followed by resume operation, min. 200ns is needed for checking the busy status.

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 27 -

NOR FLASH MEMORY

Program Suspend / Resume

The device provides the Program Suspend/Resume mode. This mode is used to enable Data Read by suspending the Program operation.

The device accepts a Program Suspend command in Program mode(including Program operations performed during Erase Suspend) but

other commands are ignored. After input of the Program Suspend command, 5us is needed to enter the Program Suspend Read mode.

Therefore system must wait for 5us(recovery time) to read the data from the bank which include the block being programmed. Othwewise,

system can read the data immediately from a bank which don't include block being programmed without ecovery time(max. 5us) after Pro-

gram Suspen command. Like an Erase Suspend mode, the device can be returned to Program mode by using a Program Resume command.

In the program suspend mode, protect/unprotect command is prohibited. In program suspend followed by resume operation, min. 200ns

is needed for checking the busy status.

Read While Write Operation

The device is capable of reading data from one bank while writing in the other banks. This is so called the Read While Write operation. An

erase operation may also be suspended to read from or program to another location within the same bank(except the block being erased).

The Read While Write operation is prohibited during the chip erase operation. Figure 17 shows how read and write cycles may be initiated for

simultaneous operation with zero latency. Refer to the DC Characteristics table for read-while-write current specifications.

OTP Block Region

The OTP Block feature provides a 512-word Flash memory region that enables permanent part identification through an Electronic Serial

Number (ESN). The OTP Block is customer lockable and shipped with itself unlocked, allowing customers to untilize the that block in any man-

ner they choose. The customer-lockable OTP Block has the Protection Verify Bit (DQ0) set to a "0" for Unlocked state or a "1" for Locked state.

The system accesses the OTP Block through a command sequence (see "Enter OTP Block / Exit OTP Block Command sequence" at Table8).

After the system has written the "Enter OTP Block" Command sequence, it may read the OTP Block by using the addresses

(FFFF80h~FFFFFFh) normally and may check the Protection Verify Bit (DQ0) by using the "Autoselect Block Protection Verify" Command

sequence with OTP Block address. This mode of operation continues until the system issues the "Exit OTP Block" Command suquence, a

hardware reset or until power is removed from the device. On power-up, or following a hardware reset, the device reverts to sending com-

mands to main blocks. Note that the Accelerated function and unlock bypass modes are not available when the OTP Block is enabled.

Customer Lockable

In a Customer lockable device, The OTP Block is one-time programmable and can be locked only once. Note that the Accelerated program-

ming and Unlock bypass functions are not available when programming the OTP Block. Locking operation to the OTP Block is started by writ-

ing the "Enter OTP Block" Command sequence, and then the "Block Protection" Command seqeunce (Table 5) with an OTP Block address.

The Locking operation has to be above 100us. "Exit OTP Block" commnad sequence and Hardware reset makes locking operation finished

and then exiting from OTP Block after 30us.

The OTP Block Lock operation must be used with caution since, once locked, there is no procedure available for unlocking and

none of the bits in the OTP Block space can be modified in any way.

Suspend and resume operation are not supported during OTP protect, nor is OTP protect supported during any suspend opera-

tions.

Low VCC Write Inhibit

To avoid initiation of a write cycle during Vcc power-up and power-down, a write cycle is locked out for Vcc less than VLKO. If the Vcc < VLKO

(Lock-Out Voltage), the command register and all internal program/erase circuits are disabled. Under this condition the device will reset itself

to the read mode.Subsequent writes will be ignored until the Vcc level is greater than VLKO. It is the user’s responsibility to ensure that the con-

trol pins are logically correct to prevent unintentional writes when Vcc is above VLKO.

Write Pulse “Glitch” Protection

Noise pulses of less than 5ns (typical) on OE, CE, AVD or WE do not initiate a write cycle.

Logical Inhibit

Write cycles are inhibited by holding any one of OE = VIL , CE = VIH or WE = VIH. To initiate a write cycle, CE and WE must be a logical zero

while OE is a logical one.

Deep Power Down

In order to reduce the power consumption of the device, it shall a deep power down mode inplemented on a seperate pin. The deep power

down mode is active when the deep power down signal is activated, high state. In deep power down the device shall turn off all circuitry in

order to reach a power consumption of 2uA(Tpy). The device shall exit the deep power down mode within 70us after that the deep power

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 28 -

NOR FLASH MEMORY

down signal has been de-activated, set to low. In deep power down the state of the device chip select shall have no impact on the device

power consumption. All programming capabilities of the device are inhibited.

At the power up, the device shall accept any order of activation of the reset and deep power down signal. The device shall respond within the

specified time for the signal that was deactivated/activated latest. The deep power down mode is activated when DPD pin high state only. If

DPD is asserted during a program or erase operation, the device requires a time of tDP(During Internal Routines) before the device is ready to

enter DPD mode.

Deep Power Down (DPD)

NOTE

Not 100% tested.

SWITCHING WAVEFORMS

Figure 1. DPD Timings

Parameter Symbol All Speed Options Unit

Min Typ Max

DPD Pin High(NOT During Internal Routines)

to DPD Mode (Note) tDP 100 - - ns

DPD Pin High(During Internal Routines)

to DPD Mode (Note) tDP 20 - - µs

DPD Low Time Before Read (Note) twkup 75 --

µs

twkup

CE, OE

DPD

tDP

twkup

CE, OE

Reset Timings NOT during Internal Routines

Reset Timings during Internal Routines

≈≈

tDP

DPD

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 29 -

NOR FLASH MEMORY

FLASH MEMORY STATUS FLAGS

The K8C54(55)15E has means to indicate its status of operation in the bank where a program or erase operation is in processes. Address

must include bank address being executed internal routine operation. The status is indicated by raising the device status flag via correspond-

ing DQ pins. The status data can be read during burst read mode by using AVD signal with a bank address. That means status read is sup-

ported in synchronous mode. If status read is performed, the data provided in the burst read is identical to the data in the initial access. To

initiate the synchronous read again, a new address and AVD pulse is needed after the host has completed status reads or the device has

completed the program or erase operation. The corresponding DQ pins are DQ7, DQ6, DQ5, DQ3, DQ2 and DQ1.

Table 10. Hardware Sequence Flags

NOTE

1) DQ2 will toggle when the device performs successive read operations from the erase/program suspended block.

2) If DQ5 is High (exceeded timing limits), successive reads from a problem block will cause DQ2 to toggle.

3) Note that DQ7 during Write-to-Buffer-Programming indicates the data-bar for DQ7 data for the last loaded write-buffer address location.

DQ7 : Data Polling

When an attempt to read the device is made while executing the Internal Program, the complement of the data is written to DQ7 as an indica-

tion of the Routine in progress. When the Routine is completed an attempt to access to the device will produce the true data written to DQ7.

When a user attempts to read the block being erased, DQ7 will be low. If the device is placed in the Erase/Program Suspend Mode, the status

can be detected via the DQ7 pin. If the system tries to read an address which belongs to a block that is being erase suspended, DQ7 will be

high. And, if the system tries to read an address which belongs to a block that is being program suspended, the output will be the true data of

DQ7 itself. If a non-erase-suspended or non-program-suspended block address is read, the device will produce the true data to DQ7. If an

attempt is made to program a protected block, DQ7 outputs complements the data for approximately 1µs and the device then returns to the

Read Mode without changing data in the block. If an attempt is made to erase a protected block, DQ7 outputs complement data in approxi-

mately 100us and the device then returns to the Read Mode without erasing the data in the block.

DQ6 : Toggle Bit

Toggle bit is another option to detect whether an Internal Routine is in progress or completed. Once the device is at a busy state, DQ6 will tog-

gle. Toggling DQ6 will stop after the device completes its Internal Routine. If the device is in the Erase/Program Suspend Mode, an attempt to

read an address that belongs to a block that is being erased or programmed will produce a high output of DQ6. If an address belongs to a

block that is not being erased or programmed, toggling is halted and valid data is produced at DQ6. If an attempt is made to program a pro-

tected block, DQ6 toggles for approximately 1us and the device then returns to the Read Mode without changing the data in the block. If an

attempt is made to erase a protected block, DQ6 toggles for approximately 100µs and the device then returns to the Read Mode without eras-

ing the data in the block.

DQ5 : Exceed Timing Limits

If the Internal Program/Erase Routine extends beyond the timing limits, DQ5 will go High, indicating program/erase failure.

Status DQ7 DQ6 DQ5 DQ3 DQ2 DQ1

In Progress

Programming DQ7 Toggle 0 0 1 0

Block Erase or Chip Erase 0 Toggle 0 1 Toggle 0

Erase Suspend Read Erase Suspended

Block 1100

Toggle

(Note 1) 0

Erase Suspend Read Non-Erase Suspended

Block Data Data Data Data Data Data

Erase Suspend

Program

Non-Erase Suspended

Block DQ7 Toggle 0 0 1 0

Program Suspend Read Program Suspended

Block DQ7 1 0 0 Toggle

(Note 1) 0

Program Suspend Read Non- program

Suspended Block Data Data Data Data Data Data

Exceeded

Time Limits

Programming DQ7 Toggle 1 0 No Toggle 0

Block Erase or Chip Erase 0 Toggle 1 1 (Note 2) 0

Erase Suspend Program DQ7 Toggle 1 0 No Toggle 0

Write-to-

Buffer

(Note3)

BUSY state DQ7 Toggle 0 0 No Toggle 0

Exceeded Timing Limits DQ7 Toggle 1 0 No Toggle 0

ABORT State DQ7 Toggle 0 0 No Toggle 1

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 30 -

NOR FLASH MEMORY

DQ3 : Block Erase Timer

The status of the multi-block erase operation can be detected via the DQ3 pin. DQ3 will go High if 50µs of the block erase time window

expires. In this case, the Internal Erase Routine will initiate the erase operation.Therefore, the device will not accept further write commands

until the erase operation is completed. DQ3 is Low if the block erase time window is not expired. Within the block erase time window, an addi-

tional block erase command (30H) can be accepted. To confirm that the block erase command has been accepted, the software may check

the status of DQ3 following each block erase command.

DQ2 : Toggle Bit 2

The device generates a toggling pulse in DQ2 only if an Internal Erase Routine or an Erase/Program Suspend is in progress. When the device

executes the Internal Erase Routine, DQ2 toggles only if an erasing block is read. Although the Internal Erase Routine is in the Exceeded

Time Limits, DQ2 toggles only if an erasing block in the Exceeded Time Limits is read. When the device is in the Erase/Program Suspend

mode, DQ2 toggles only if an address in the erasing or programming block is read. If a non-erasing or non-programmed block address is read

during the Erase/Program Suspend mode, then DQ2 will produce valid data. DQ2 will go High if the user tries to program a non-erase sus-

pend block while the device is in the Erase Suspend mode.

DQ1 : Buffer Program Abort Indicator

DQ1 indocates whether a Write-to-Buffer operation was aborted. Under these conditions DQ1 produces a "1". The system must issue the

Write-to-Buffer-Abort-Reset command sequence to return the device to reading array data.

RDY: Ready

Normally the RDY signal is used to indicate if new burst data is available at the rising edge of the clock cycle or not. If RDY is low state, data

is not valid at expected time, and if high state, data is valid. Note that, if CE is low and OE is high, the RDY is high state.

Figure 2. Data Polling Algorithms F

igure 3. Toggle Bit Algorithms

Start

DQ7 = Data ?

DQ5 = 1 ?

Fail Pass

Yes

DQ7 = Data ?

Yes

Read(DQ0~DQ7)

Valid Address

Read(DQ0~DQ7)

Valid Address

Start

DQ6 = Toggle ?

DQ5 = 1 ?

Fail Pass

DQ6 = Toggle ?

Yes

Read twice(DQ0~DQ7)

Valid Address

Read(DQ0~DQ7)

Valid Address

Yes Yes

Read(DQ0~DQ7)

Valid Address

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 31 -

NOR FLASH MEMORY

Commom Flash Memory Interface

Common Flash Momory Interface is contrived to increase the compatibility of host system software. It provides the specific information of the

device, such as memory size and electrical features. Once this information has been obtained, the system software will know which command

sets to use to enable flash writes, block erases, and control the flash component.

When the system writes the CFI command(98H) to address 55H , the device enters the CFI mode. And then if the system writes the address

shown in Table 11, the system can read the CFI data. Query data are always presented on the lowest-order data outputs(DQ0-7) only. In

word(x16) mode, the upper data outputs(DQ8-15) is 00h. To terminate this operation, the system must write the reset command.

Table 11. Common Flash Memory Interface Code

Description Addresses

(Word Mode) Data

Query Unique ASCII string "QRY"

10H

11H

12H

0051H

0052H

0059H

Primary OEM Command Set 13H

14H

0002H

0000H

Address for Primary Extended Table 15H

16H

0040H

0000H

Alternate OEM Command Set (00h = none exists) 17H

18H

0000H

Address for Alternate OEM Extended Table (00h = none exists) 19H

1AH

0000H

Vcc Min. (write/erase)

D7-D4: volt, D3-D0: 100 millivolt 1BH 0017H

Vcc Max. (write/erase)

D7-D4: volt, D3-D0: 100 millivolt 1CH 0019H

Vpp(Acceleration Program) Supply Minimum

00 = Not Supported, D7 - D4 : Volt, D3 - D0 : 100mV 1DH 0085H

Vpp(Acceleration Program) Supply Maximum

00 = Not Supported, D7 - D4 : Volt, D3 - D0 : 100mV 1EH 0095H

Typical timeout per single word write 2N us 1FH 0008H

Typical timeout for Max buffer write 2N us(00H = not supported) 20H 0009H

Typical timeout per individual block erase 2N ms 21H 000AH

Typical timeout for full chip erase 2N ms(00H = not supported) 22H 0012H

Max. timeout for word write 2N times typical 23H 0001H

Max. timeout for buffer write 2N times typical 24H 0001H

Max. timeout per individual block erase 2N times typical 25H 0004H

Max. timeout for full chip erase 2N times typical(00H = not supported) 26H 0000H

Device Size = 2N byte 27H 0019H

Flash Device Interface description 28H

29H

0000H

Max. number of byte in multi-byte write = 2N2AH

2BH

0006H

0000H

Number of Erase Block Regions within device 2CH 0002H

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 32 -

NOR FLASH MEMORY

Table 11. Common Flash Memory Interface Code (Continued)

* Max. Operating Clock Frequency : Data is 53H in 66/83Mhz part (K8C5415ET(B)M)

Description Addresses

(Word Mode) Data

Erase Block Region 1 Information

Bits 0~15: y+1=block number

Bits 16~31: block size= z x 256bytes

2DH

2EH

2FH

30H

0003H

0000H

0080H

0000H

Erase Block Region 2 Information

31H

32H

33H

34H

00FEH

0000H

0002H

Erase Block Region 3 Information

35H

36H

37H

38H

0000H

Erase Block Region 4 Information

39H

3AH

3BH

3CH

0000H

Query-unique ASCII string "PRI"

40H

41H

42H

0050H

0052H

0049H

Major version number, ASCII 43H 0030H

Minor version number, ASCII 44H 0030H

Address Sensitive Unlock(Bits 1-0)

0 = Required, 1= Not Required

Silcon Revision Number(Bits 7-2)

45H 0000H

Erase Suspend

0 = Not Supported, 1 = To Read Only, 2 = To Read & Write 46H 0002H

Block Protect

00 = Not Supported, 01 = Supported 47H 0001H

Block Temporary Unprotect 00 = Not Supported, 01 = Supported 48H 0000H

Block Protect/Unprotect scheme 00 = Not Supported, 01 = Supported 49H 0001H

Simultaneous Operation

00 = Not Supported, 01 = Supported 4AH 0001H

Burst Mode Type 00 = Not Supported, 01 = Supported 4BH 0001H

Page Mode Type

00 = Not Supported, 01 = 4 Word Page 02 = 8 Word Page 4CH 0000H

Top/Bottom Boot Block Flag

02H = Bottom Boot Device, 03H = Top Boot Device 4DH 0003H

Max. Operating Clock Frequency (MHz )* 4EH 0085H

RWW(Read While Write) Functionality Restriction (00H = non exists , 01H = exists) 4FH 0000H

Handshaking

00 = Not Supported at both mode, 01 = Supported at Sync. Mode

10 = Supported at Async. Mode, 11 = Supported at both Mode

50H 0001H

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 33 -

NOR FLASH MEMORY

ABSOLUTE MAXIMUM RATINGS

NOTE

1) Minimum DC voltage is -0.5V on Input/ Output pins. During transitions, this level may fall to -2.0V for periods <20ns.

Maximum DC voltage is Vcc+0.6V on input / output pins which, during transitions, may overshoot to Vcc+2.0V for periods <20ns.

2) Minimum DC input voltage is -0.5V on VPP . During transitions, this level may fall to -2.0V for periods <20ns.

Maximum DC input voltage is +9.5V on VPP which, during transitions, may overshoot to +12.0V for periods <20ns.

3) Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to the conditions

detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect reliability.

Parameter Symbol Rating Unit

Voltage on any pin relative to VSS

Vcc Vcc -0.5 to +2.5

VPP VIN

-0.5 to +9.5

All Other Pins -0.5 to +2.5

Temperature Under Bias Commercial Tbias

-10 to +125 °C

Extended -25 to +125

Storage Temperature Tstg -65 to +150 °C

Short Circuit Output Current IOS 5mA

Operating Temperature TA (Commercial Temp.) 0 to +70 °C

TA (Extended Temp.) -25 to + 85 °C

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 34 -

NOR FLASH MEMORY

RECOMMENDED OPERATING CONDITIONS ( Voltage reference to GND )

DC CHRACTERISTICS

NOTE

1) Maximum ICC specifications are tested with VCC = VCCmax.

2) ICC active while Internal Erase or Internal Program is in progress.

3) Device enters automatic sleep mode when addresses are stable for tAA + 60ns.

CAPACITANCE(TA = 25 °C, VCC = 1.8V, f = 1.0MHz)

NOTE

Capacitance is periodically sampled and not 100% tested.

Parameter Symbol Min Typ. Max Unit

Supply Voltage VCC 1.7 1.8 1.95 V

Supply Voltage VSS 000V

Parameter Symbol Test Conditions Min Typ Max Unit

Input Leakage Current ILI VIN=VSS to VCC, VCC=VCCmax - 1.0 - + 1.0 µA

VPP Leakage Current ILIP VCC=VCCmax , VPP=9.5V - - 35 µA

Output Leakage Current ILO VOUT=VSS to VCC, VCC=VCCmax, OE=VIH - 1.0 - + 1.0 µA

Active Burst Read Current ICCB1 CE=VIL, OE=VIH (@133MHz) - 35 55 mA

Active Asynchronous

Read Current ICC1 CE=VIL, OE=VIH

10MHz - 35 55 mA

1MHz - 8 10 mA

Active Write Current (Note 2) ICC2 CE=VIL, OE=VIH, WE=VIL, VPP=VIH -2540mA

Read While Write Current ICC3 CE=VIL, OE=VIH -4570mA

Accelerated Program Current ICC4 CE=VIL, OE=VIH , VPP=9.5V - 20 30 mA

Standby Current ICC5 CE= RESET=VCC ± 0.2V - 30 110 µA

Standby Current During Reset ICC6 RESET = VSS ± 0.2V - 30 110 µA

Automatic Sleep Mode(Note 3) ICC7 CE=VSS ± 0.2V, Other Pins=VIL or VIH

VIL = VSS ± 0.2V, VIH = VCC ± 0.2V -30110µA

Deep Power Down Mode Icc8 - 2 20 µA

Input Low Voltage VIL -0.5 - 0.4 V

Input High Voltage VIH VCC-0.4 - VCC+0.4 V

Output Low Voltage VOL IOL = 100 µA , VCC=VCCmin - - 0.1 V

Output High Voltage VOH IOH = -100 µA , VCC=VCCmin VCC-0.1 - - V

Voltage for Accelerated Program VID 8.5 9.0 9.5 V

Low VCC Lock-out Voltage VLKO 1.0 - - V

Vpp current in program/erase Ivpp Vpp = 9.5V - 0.8 5 mA

Vpp = 1.95V - - 50 µA

Item Symbol Test Condition Min Max Unit

Input Capacitance CIN VIN=0V - 4 pF

Output Capacitance COUT VOUT=0V - 6 pF

Control Pin Capacitance CIN2 VIN=0V -4pF

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 35 -

NOR FLASH MEMORY

AC TEST CONDITION

NOTE

If clock rising time is longer than 1ns, (tr/2-0.5)ns should be added to the parameter. Assumed input rise and fall time (tr & tf) = 1ns.

If tr & tf is longer than 1ns, transient time compensation should be considered,i.e., [(tr + tf)/2-1]ns should be added to the parameter.

AC CHARACTERISTICS

Synchronous/Burst Read

NOTE

Not 100% tested.

Parameter Value

Input Pulse Levels 0V to VCC

Input Rise and Fall Times 1ns*

Input and Output Timing Levels VCC/2

Output Load CL = 30pF

Parameter Symbol

(66 MHz)

(83 MHz)

(108 MHz)

(133 MHz) Unit

Min Max Min Max Min Max Min Max

Initial Access Time tIAA - 100 - 100 - 100 - 100 ns

Burst Access Time Valid Clock

to Output Delay tBA -11-9-7- 6ns

AVD Setup Time to CLK tAVDS 5-4-4-2.5-ns

AVD Hold Time from CLK tAVDH 2-2-2-2 -ns

Address Setup Time to CLK tACS 5-4-4-2.5-ns

Address Hold Time from CLK tACH 6-5-2-2 -ns

Data Hold Time from Next

Clock Cycle tBDH 4-4-3-3 -ns

Output Enable to RDY valid tOER -11-9-7- 6ns

CE Disable to High Z tCEZ - 15 - 15 - 15 - 15 ns

OE Disable to High Z tOEZ - 15 - 15 - 15 - 15 ns

CE Setup Time to CLK tCES 4.5 - 4.5 - 4.5 - 4.5 - ns

CLK to RDY Setup Time tRDYA -11-9-7- 6ns

RDY Setup Time to CLK tRDYS 3-3-2-2 -ns

CLK High or Low Time tCLKH/L 3.5 - 3 - 2.5 - 2.5 - ns

CLK Fall or Rise Time tCLKHCL -3-3-2- 1ns

VCC

VCC/2 VCC/2

Input Pulse and Test Point

Input & Output

Test Point

Output Load

Device

Under

Tes t

* CL = 30pF including scope

and Jig capacitance

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 36 -

NOR FLASH MEMORY

SWITCHING WAVEFORMS

Figure 4. Continuous Burst Mode Read (133 MHz)

Figure 5. Continuous Burst Mode Read (108 MHz)

tCES

tAVDS

tAVDH

tACS

tACH

tIAA

tOER

tBA

tBDH

tCEZ

tOEZ

Hi-Z

≈ ≈ ≈ ≈ ≈ ≈ ≈ ≈

tRDYS

7.5ns typ(133MHz).

CLK

AVD

DQ0:

DQ15

RDY

14 cycles for initial access shown.

CR setting : A14=1, A13=0, A12=1, A11=0

Da Da+n

Da+1 Da+2 Da+3 Da+4 Da+5 Da+6

≈ ≈ ≈ ≈ ≈ ≈ ≈ ≈

tCES

tAVDS

tAVDH

tACS

tACH

tIAA

tOER

tBA

tBDH

tCEZ

tOEZ

Hi-Z

Da Da+1 Da+2 Da+n

Da+3

≈ ≈ ≈ ≈ ≈ ≈≈ ≈

tRDYS

9.25ns typ(108MHz).

Da+4 Da+5 Da+6

11 cycles for initial access shown.

CR setting : A14=0, A13=1, A12=1, A11=1

CLK

AVD

DQ0:

DQ15

RDY

A0-A23

≈ ≈ ≈ ≈ ≈ ≈≈ ≈

≈

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 37 -

NOR FLASH MEMORY

SWITCHING WAVEFORMS

Figure 6. 8 word Linear Burst Mode with Wrap Around (133 MHz)

Figure 7. 8 word Linear Burst with RDY Set One Cycle Before Data (Wrap Around Mode, CR setting : A18=1)

tCES

tAVDS

tAVDH

tACS

tACH

tIAA

tOER

tBA

tBDH

Hi-Z

tRDYS

7.5ns typ(133MHz).

CLK

AVD

DQ0:

DQ15

RDY

A0-A23

14 cycles for initial access shown.

CR setting : A14=1, A13=0, A12=1, A11=0

D7 D0 D1 D2 D3 D4 D5 D6 D7 D0

≈ ≈ ≈ ≈

≈≈ ≈

≈≈

tCES

tAVDS

tAVDH

tACS

tACH

tIAA

tOER

tBA

tBDH

Hi-Z

tRDYS

7.5ns typ(133MHz).

CLK

AVD

DQ0:

DQ15

RDY

A0-A23

14 cycles for initial access shown.

CR setting : A14=1, A13=0, A12=1, A11=0

D7 D0 D1 D2 D3 D4 D5 D6 D7 D0

tRDYA

≈ ≈ ≈ ≈

≈≈ ≈

≈≈

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 38 -

NOR FLASH MEMORY

SWITCHING WAVEFORMS

Figure 8. 8 word Linear Burst Mode (No Wrap Case)

AC CHARACTERISTICS

Asynchronous Read

NOTE

Not 100% tested.

Parameter Symbol All Speed option Unit

Min Max

Access Time from CE Low tCE - 100 ns

Asynchronous Access Time tAA - 100 ns

AVD Low Setup Time to CE Enable tAVDCS 0-ns

AVD Low Hold Time from CE Disable tAVDCH 0-ns

Output Enable to Output Valid tOE -15ns

Output Enable Hold

Time

Read

tOEH

0-ns

Toggle and Data Polling 10 - ns

Output Disable to High Z(Note) tOEZ -15ns

tCES

tAVDS

tAVDH

tACS

tACH

tIAA

tOER

tBA

tBDH

tCEZ

tOEZ

Hi-Z

tRDYS

7.5ns typ(133MHz).

CLK

AVD

DQ0:

DQ15

RDY

A0-A23

14 cycles for initial access shown.

CR setting : A14=1, A13=0, A12=1, A11=0

D7 D14

D8 D9 D10 D11 D12 D13

≈ ≈ ≈ ≈ ≈≈ ≈

≈

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 39 -

NOR FLASH MEMORY

SWITCHING WAVEFORMS

Asynchronous Mode Read

NOTE

VA=Valid Read Address, RD=Read Data.

AVD should be held VIL in asynchronous read mode.

Asynchronous mode may not support read following four sequential invalid read condition within 200ns.

Figure 9. Asynchronous Mode Read

AC CHARACTERISTICS

Hardware Reset(RESET)

NOTE

Not 100% tested.

Parameter Symbol All Speed Options Unit

Min Max

RESET Pin Low(During Internal Routines)

to Read Mode (Note) tReady -20

µs

RESET Pin Low(NOT During Internal Routines)

to Read Mode (Note) tReady - 500 ns

RESET Pulse Width*tRP 200 - ns

Reset High Time Before Read (Note) tRH 200 - ns

RESET Low to Standby Mode tRPD 20 - µs

tOE

Valid RD

tCE

tOEH

tOEZ

DQ0-DQ15

A0-A23

tAA

CLK VIL

AVD

tAVDCS tAVDCH

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 40 -

NOR FLASH MEMORY

SWITCHING WAVEFORMS

Figure 10. Reset Timings

tRH

CE, OE

RESET

tRP

tReady

CE, OE

RESET

tRP

Reset Timings NOT during Internal Routines

Reset Timings during Internal Routines

≈ ≈

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 41 -

NOR FLASH MEMORY

AC CHARACTERISTICS

Erase/Program Operation

NOTE

1) Not 100% tested.

2) Internal programming algorithm is optimized for Buffer Program, so Normal word programming or Single word Buffer Program use

Buffer Program algorithm.

3) Internal programming algorithm for supporting Accelerated mode uses a method to double the number of words programmed

simultaneously.

4) Typical 32-words Buffer Program time pays due regard to that Each program data pattern ("11", "10". "01", "00") has a same

portion in 32 words Buffer.

Parameter Symbol All speed options Unit

Min Typ Max

WE Cycle Time(Note 1) tWC 100 - - ns

Address Setup Time tAS 0--ns

Address Hold Time tAH 60 - - ns

Data Setup Time tDS 60 - - ns

Data Hold Time tDH 0--ns

Read Recovery Time Before Write tGHWL 0--ns

CE Setup Time tCS 0--ns

CE Hold Time tCH 0--ns

WE Pulse Width tWP 60 - - ns

WE Pulse Width High tWPH 40 - - ns

Latency Between Read and Write Operations tSR/W 0--ns

Word Programming Operation (Note 2) tPGM -80-

µs

Single word Buffer Program (Note 2) tPGM_BP -80-

µs

32 words Buffer Program (Note 4) tPGM_BP -320-

µs

Accelerated Programming Operation (Note 3) tACCPGM -80-

µs

Accelerated Single word Buffer Program (Note 3) tACCPGM_BP -80-

µs

Accelerated 32 words Buffer Program (Note 4) tACCPGM_BP -128-

µs

Block Erase Operation tBERS -0.6-sec

VPP Rise and Fall Time tVPP 500 - - ns

VPP Setup Time (During Accelerated Programming) tVPS 1--

µs

VCC Setup Time tVCS 50 - - µs

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 42 -

NOR FLASH MEMORY

Erase/Program Performance

NOTE

1) 25°C, VCC = 1.8V, 100,000 cycles, typical pattern.

2) System-level overhead is defined as the time required to execute the two or four bus cycle command necessary to program each

word.

3) 100K Program/Erase Cycle in all Bank

SWITCHING WAVEFORMS

Program Operations

NOTE

1) PA = Program Address, PD = Program Data, VA = Valid Address for reading status bits.

2) “In progress” and “complete” refer to status of program operation.

3) A16–A23 are don’t care during command sequence unlock cycles.

4) Status reads in this figure is asynchronous read, but status read in synchronous mode is also supported.

Figure 11. Program Operation Timing

Parameter Limits Unit Comments

Min. Typ. Max.

Block Erase Time 64 Kword - 0.6 3.0

sec Includes 00h programming

prior to erasure

16 Kword - 0.3 1.5

Chip Erase Time - 154 771

Accelerated Block Erase Time

64 Kword - 0.4 3.0

16 Kword - 0.2 1.5

Accelerated Chip Erase Time - 103 771

Word Programming Time - 80 550

µs / word Excludes system level over-

head

32 words Buffer Programming Time - 10 32

Accelerated Word Programming Time - 80 550

Accelerated 32 words Buffer Programming Time - 4 22

Chip Programming Time - 168 537 sec Excludes system level over-

head

Accelerated Chip Programming Time - 68 370

Program Command Sequence (last two cycles)

A0:A23

CLK

tAH

tDS

tDH

tCH

tWP

tCS

tWPH

tWC

tPGM

tVCS

PA VA VA

Progress Complete

PDA0h

555h

DQ0-DQ15

VCC

Read Status Data

VIL

≈ ≈ ≈ ≈ ≈ ≈ ≈

tAS

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 43 -

NOR FLASH MEMORY

SWITCHING WAVEFORMS

Buffer Program Operations

NOTE

1) BA = Block Address, WC = Word Count, PA = Program Address, PD = Program Data, VA = Valid Address for reading status bits.

2) Sequential PA_1, PA_2, ... , PA_N must have same address bits A23(max.) ~ A5 as PA_0 entered firstly

3) The number of Program/Data pairs entered must be same as WC+1 because WC = N.

4) “In progress” and “complete” refer to status of program operation.

5) A16–A23 are don’t care during command sequence unlock cycles.

6) Status reads in this figure is asynchronous read, but status read in synchronous mode is also supported.

Figure 12. Buffer Program Operation Timing

A0:A23

CLK

tAS

tAH

tDS

tWP

tCS

tWPH

tWC

tVCS

AAh

DQ0:

DQ15

VCC

≈≈ ≈ ≈ ≈ ≈

55h 25h WC PD_0 PD_1 PD_N 29h

≈

BA BA PA_0 PA_1 PA_N BA

tPGM_BP

Buffer Program Command Sequence Word Count Program Address/Data pairs (WC+1) "Buffer to Flash"

555h 2AAh

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 44 -

NOR FLASH MEMORY

SWITCHING WAVEFORMS

Erase Operation

NOTE

1) BA is the block address for Block Erase.

2) Address bits A16–A23 are don’t cares during unlock cycles in the command sequence.

3) Status reads in this figure is asynchronous read, but status read in synchronous mode is also supported.

Figure 13. Chlp/Block Erase Operations

SWITCHING WAVEFORMS

Unlock Bypass Program Operations(Accelerated Program)

Erase Command Sequence (last two cycles)

A0:A23

tDS

tDH

tCH

tBERS

tVCS

BA VA VA

Progress Complete

30h55h

2AAh

DQ0-DQ15

VCC

Read Status Data

555h for

chip erase

10h for

chip erase

tWP

tCS

tWPH

tWC

CLK VIL

≈ ≈ ≈ ≈ ≈ ≈ ≈

tAH

tAS

VPP

DQ0:

DQ15

1us tVPS

VIL or VIH

VID

tVPP

Don’t Care A0h PD Don’t Care

Don’t Care

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 45 -

NOR FLASH MEMORY

Unlock Bypass Block Erase Operations

NOTE

1) VPP can be left high for subsequent programming pulses.

2) Use setup and hold times from conventional program operations.

3) Conventional Program/Erase commands as well as Unlock Bypass Program/Erase commands can be used when the VID is

applied to Vpp.

Figure 14. Unlock Bypass Operation Timings

SWITCHING WAVEFORMS

Data Polling Operations

NOTE

VA = Valid Address. When the Internal Routine operation is complete, and Data Polling will output true data.

Figure 15. Data Polling Timings (During Internal Routine)

A0:A23

VPP

DQ0:

DQ15

1us tVPS

VIL or VIH

VID

tVPP

Don’t Care 80h 30h Don’t Care

555h for

chip erase

10h for

chip erase

Don’t Care

tCES

tAVDS

tAVDH

tACS

tACH

tIAA

Hi-Z

CLK

AVD

DQ0:

DQ15

RDY

A0-A23

≈ ≈ ≈ ≈ ≈ ≈

tRDYS

Status Data

≈ ≈ ≈

≈≈≈ ≈ ≈ ≈

Status Data

≈ ≈ ≈

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 46 -

NOR FLASH MEMORY

Toggle Bit Operations

NOTE

VA = Valid Address. When the Internal Routine operation is complete, the toggle bits will stop toggling.

Figure 16. Toggle Bit Timings(During Internal Routine)

SWITCHING WAVEFORMS

Read While Write Operations

NOTE

Breakpoints in waveforms indicate that system may alternately read array data from the “non-busy bank” and checking the status of the program or erase opera-

tion in the “busy” bank.

Figure 17. Read While Write Operation

tAVDS

tAVDH

tACS

tACH

tIAA

Hi-Z

CLK

AVD

DQ0:

DQ15

RDY

≈ ≈ ≈ ≈ ≈ ≈

tRDYS

Status Data

≈ ≈ ≈

≈≈≈ ≈ ≈ ≈

Status Data

≈ ≈ ≈

tWC

DQ0:

AVD

DQ15

A0-A23

PD/30h AAh

PA/BA RA RA

RD RD

Last Cycle in

Program or

Block Erase

Command Sequence

Read status in same bank

and/or array data from other bank

tRC tRC tWC

tOE

tOEH

tWPH tWP tAA

tOEH

tDS tDH

tSR/W

tAS

tAH

tGHWL

Command Sequences

Program or Erase

Begin another

≈ ≈ ≈ ≈ ≈ ≈

555h

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 47 -

NOR FLASH MEMORY

Crossing of First Word Boundary in Burst Read Mode

The additional clock insertion for word boundary is needed only at the first crossing of word boundary. This means that no addtional clock

cycle is needed from 2nd word boundary crossing to the end of continuous burst read. Also, the number of addtional clock cycle for the first

word boundary can vary from zero to fourteen cycles, and the exact number of additional clock cycle depends on the starting address of burst

read and programmable wait state settings. For example, if the starting address is 16N+15 (the worst case) and programmable wait state set-

ting(A<14:11>) is "0011" (which means data is valid on the 7th active CLK edge after AVD transition to Vih), six additional clock cycle is

needed.

Similarly, if the starting address is 16N+15 (the worst case) and programmable wait state setting(A<14:11>) is "0010" (which means data is

valid on the 6th active CLK edge after AVD transition to Vih), five additional clock cycle is needed.

Below table shows the starting address vs. addtional clock cycles for first word boundary.

Starting Address vs. Additional Clock Cycles for first word boundary

NOTE

Address bit A<14:11> means the programmable wait state on burst mode configuration register. Refer to Table 7.

Srarting

Address

Group for

Burst Read

The Residue of

(Address/16)

LSB Bits

Address

Additional Clock Cycles for First Word Boundary (note1)

A<14:11> "0000"

Valid data : 4th

CLK

A<14:11> "0001"

Valid data : 5th

CLK

A<14:11> "0010"

Valid data : 6th

CLK

... A<14:11> "1011"

Valid data : 15th CLK

16N 0 0000 0 cycle 0 cycle 0 cycle ... 0 cycle

16N+1 1 0001 0 cycle 0 cycle 0 cycle ... 0 cycle

16N+2 2 0010 0 cycle 0 cycle 0 cycle ... 1 cycle

16N+3 3 0011 0 cycle 0 cycle 0 cycle ... 2 cycle

16N+4 4 0100 0 cycle 0 cycle 0 cycle ... 3 cycle

16N+5 5 0101 0 cycle 0 cycle 0 cycle ... 4 cycle

16N+6 6 0110 0 cycle 0 cycle 0 cycle ... 5 cycle

16N+7 7 0111 0 cycle 0 cycle 0 cycle ... 6 cycle

16N+8 8 1000 0 cycle 0 cycle 0 cycle ... 7 cycle

16N+9 9 1001 0 cycle 0 cycle 0 cycle ... 8 cycle

16N+10 10 1010 0 cycle 0 cycle 0 cycle ... 9 cycle

16N+11 11 1011 0 cycle 0 cycle 1 cycle ... 10 cycle

16N+12 12 1100 0 cycle 1 cycle 2 cycle ... 11 cycle

16N+13 13 1101 1 cycle 2 cycle 3 cycle ... 12 cycle

16N+14 14 1110 2 cycle 3 cycle 4 cycle ... 13 cycle

16N+15 15 1111 3 cycle 4 cycle 5 cycle ... 14 cycle

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 48 -

NOR FLASH MEMORY

Case1 : Start from "16N" address group

NOTE

1) Address boundry occurs every 16 words beginning at address 000000FH , 000001FH , 000002FH , etc.

2) Address 0000000H is also a boundry crossing.

3) No additional clock cycles are needed except for 1st boundary crossing.

Figure 18. Crossing of first word boundary in burst read mode.

Case2 : Start from "16N+2" address group

14th rising edge CLK

CR setting : A14=1, A13=0, A12=1, A11=0

RDY

CLK

Data Bus

AVD

tCEZ

tOEZ

OER

00 0D 11 12 13 14

No Additional Cycle for First Word Boundary

0E 0F 10

≈≈≈≈≈

A0-A23

≈ ≈

0D 11 12 1310

0C 0E 0F

≈≈≈

RDY

CLK

AVD

tCEZ

tOEZtOER

02 0E 11 12 13 14

Additional 1 Cycle for First Word Boundary

0F 10

14th rising edge CLK

CR setting : A14=1, A13=0, A12=1, A11=0

≈

≈≈

≈

Data Bus

A0-A23

≈ ≈

0E 11 12 1310

0D 0F

≈≈≈

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 49 -

NOR FLASH MEMORY

Case3 : Start from "16N+3" address group

NOTE

1) Address boundry occurs every 16 words beginning at address 000000FH , 000001FH , 000002FH , etc.

2) Address 0000000H is also a boundry crossing.

3) No additional clock cycles are needed except for 1st boundary crossing.

Figure 19. Crossing of first word boundary in burst read mode.

Case4 : Start from "16N+15" address group

NOTE

1) Address boundry occurs every 16 words beginning at address 000000FH , 000001FH , 000002FH , etc.

2) Address 0000000H is also a boundry crossing.

3) No additional clock cycles are needed except for 1st boundary crossing.

Figure 20. Crossing of first word boundary in burst read mode.

RDY

CLK

AVD

tCEZ

tOEZtOER

03 0F 11 12 13 14

Additional 2 Cycle for First Word Boundary

≈

≈≈

≈

CR setting : A14=1, A13=0, A12=1, A11=0

Data Bus

A0-A23

≈ ≈

0F 11 12 1310

≈≈≈

RDY

CLK

AVD

tOER

0F 10 11

Additional 14 Cycle for First Word Boundary

14th rising edge CLK

CR setting : A14=1, A13=0, A12=1, A11=0

≈

Data Bus

A0-A23

≈ ≈

≈ ≈ ≈ ≈ ≈≈≈

10 11

≈≈

≈

Revision 1.5

December 2006

K8C54(55)15ET(B)M

- 50 -

NOR FLASH MEMORY

Case5 : Start from "16N+15" address group

NOTE

1) Address boundry occurs every 16 words beginning at address 000000FH , 000001FH , 000002FH , etc.

2) Address 0000000H is also a boundry crossing.

3) No additional clock cycles are needed except for 1st boundary crossing.

4) RDY setting behaves same way both case in crossing a word boundary and valid data on the output.

Figure 21. Crossing of first word boundary in burst read mode.

14th rising edge CLK

CR setting : A14=1, A13=0, A12=1, A11=0

A18=1(RDY set One cycle before data)

RDY

CLK

AVD

tOER

0F 10 11

Additional 14 Cycle for First Word Boundary

≈

≈≈

≈

Data Bus

A0-A23

≈ ≈

≈ ≈ ≈ ≈ ≈≈≈

10 11

≈≈

≈