LTC3114-1 40V, 1A Synchronous Buck-Boost DC/DC Converter with Programmable Output Current DESCRIPTION FEATURES Regulates VOUT Above, Below or Equal to VIN n Single Inductor n Wide V Range: 2.2V to 40V IN n Wide V OUT Range: 2.7V to 40V n 1A Output Current in Buck Mode n 0.5A Output Current, V = 3.6V, V IN OUT = 5V n Programmable Average Output Current n Up to 96% Efficiency n Burst Mode(R) Operation, 30A No-Load I Q n Current Mode Control n 1.2MHz Ultralow Noise PWM n Accurate RUN Pin Threshold n Thermally Enhanced, 16-lead 3mm x 5mm DFN and TSSOP Packages n AEC-Q100 Qualified for Automotive Applications n APPLICATIONS 24V/28V Industrial Power Supply 12V Lead-Acid to 12V Regulator n High Power LED Driver n 12V/24V Solar Panel Battery Charging Systems n Automotive Power Systems n n The LTC(R)3114-1 is a versatile, wide operating voltage range synchronous monolithic buck-boost DC/DC converter with programmable average output current. The LTC3114-1's proprietary buck-boost PWM control circuitry delivers low noise operation across the entire operating voltage range. Current mode control ensures exceptional line and load transient responses. Synchronous, internal MOSFET switches and pin selectable Burst Mode operation maintain high efficiency across the entire range of load current. Average output current is programmed with a standard resistor and provides the basis for wide input range, high efficiency charging systems or constant current, high efficiency LED drive. Regulator turn-on is programmable through the accurate RUN pin. Quiescent current is just 3A in shutdown. Overtemperature protection, short-circuit protection and soft-start are integrated. The LTC3114-1 is offered in 16-lead 3mm x 5mm x 0.75mm DFN and 16 lead TSSOP (FE) packages. All registered trademarks and trademarks are the property of their respective owners. Protected by U.S. patents, including 6404251, 6166527. TYPICAL APPLICATION Efficiency vs Input Voltage 6.8H VIN 2.7V TO 40V 33nF 10F 20k SW1 SW2 BST2 BST1 LTC3114-1 VIN PVOUT PVIN RUN PROG MODE GND LDO PLDO FB VC PGND 68nF 4.7F 4700pF 90 2M VOUT 5V 1A 30F V > 5V IN EFFICIENCY (%) 68nF 95 499k 85 80 75 ILOAD = 300mA ILOAD = 600mA 27.4k 31141 TA01a 70 1 10 INPUT VOLTAGE (V) 40 31141 TA01b Rev. D Document Feedback For more information www.analog.com 1 LTC3114-1 ABSOLUTE MAXIMUM RATINGS (Note 1) VIN, PVIN, PVOUT......................................... -0.3V to 45V VBST1......................................VSW1 - 0.3V to VSW1 + 6V VBST2......................................VSW2 - 0.3V to VSW2 + 6V VRUN.............................................. -0.3V to (VIN + 0.3V) Voltage, All Other Pins.................................. -0.3V to 6V Operating Junction Temperature Range (Notes 2, 4) LTC3114E-1/LTC3114I-1...................... -40C to 125C LTC3114H-1........................................ -40C to 150C LTC3114MP-1...................................... -55C to 150C Storage Temperature Range....................-65C to 150C Lead Temperature (Soldering, 10 Sec) FE Package........................................................ 300C PIN CONFIGURATION TOP VIEW TOP VIEW PGND 1 16 MODE PGND 1 16 MODE SW2 2 15 SW1 SW2 2 15 SW1 PVOUT 3 14 PVIN PVOUT 3 14 PVIN RUN 4 13 BST1 RUN 4 PROG 5 12 BST2 PROG 5 VC 6 11 PLDO VC 6 11 PLDO FB 7 10 VIN FB 7 10 VIN GND 8 9 GND 8 9 17 PGND LDO DHC PACKAGE 16-LEAD (5mm x 3mm) PLASTIC DFN TJMAX = 150C, JA = 43C/W (4-LAYER BOARD), JC = 4C/W EXPOSED PAD (PIN 17) IS PGND, MUST BE SOLDERED TO PCB FOR RATED THERMAL PERFORMANCE 17 PGND 13 BST1 12 BST2 LDO FE PACKAGE 16-LEAD PLASTIC TSSOP TJMAX = 150C, JA = 38C/W EXPOSED PAD (PIN 17) IS PGND, MUST BE SOLDERED TO PCB FOR RATED THERMAL PERFORMANCE ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3114EDHC-1#PBF LTC3114EDHC-1#TRPBF 31141 16-Lead (5mm x 3mm) Plastic DFN -40C to 125C LTC3114IDHC-1#PBF LTC3114IDHC-1#TRPBF 31141 16-Lead (5mm x 3mm) Plastic DFN -40C to 125C LTC3114HDHC-1#PBF LTC3114HDHC-1#TRPBF 31141 16-Lead (5mm x 3mm) Plastic DFN -40C to 150C LTC3114MPDHC-1#PBF LTC3114MPDHC-1#TRPBF 31141 16-Lead (5mm x 3mm) Plastic DFN -55C to 150C LTC3114EFE-1#PBF LTC3114EFE-1#TRPBF 3114FE-1 16-Lead Plastic TSSOP -40C to 125C LTC3114IFE-1#PBF LTC3114IFE-1#TRPBF 3114FE-1 16-Lead Plastic TSSOP -40C to 125C LTC3114HFE-1#PBF LTC3114HFE-1#TRPBF 3114FE-1 16-Lead Plastic TSSOP -40C to 150C LTC3114MPFE-1#PBF LTC3114MPFE-1#TRPBF 3114FE-1 16-Lead Plastic TSSOP -55C to 150C 2 Rev. D For more information www.analog.com LTC3114-1 ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE AUTOMOTIVE PRODUCTS** LTC3114EDHC-1#WPBF LTC3114EDHC-1#WTRPBF 31141 16-Lead (5mm x 3mm) Plastic DFN -40C to 125C LTC3114IDHC-1#WPBF LTC3114IDHC-1#WTRPBF 31141 16-Lead (5mm x 3mm) Plastic DFN -40C to 125C LTC3114IFE-1#WPBF LTC3114IFE-1#WTRPBF 3114FE-1 16-Lead Plastic TSSOP -40C to 125C LTC3114EFE-1#WPBF LTC3114EFE-1#WTRPBF 3114FE-1 16-Lead Plastic TSSOP -40C to 125C Contact the factory for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Tape and reel specifications. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix. **Versions of this part are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. These models are designated with a #W suffix. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for thesemodels. ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25C (Note 2). VIN = 24V, VOUT = 5V, unless otherwise noted. PARAMETER CONDITIONS MIN VIN Operating Voltage VLDO 2.7V, -55C to 0C VLDO 2.7V, 0C to 150C l l 2.3 2.2 Output Operating Voltage (Note 5) l 2.7 Undervoltage Lockout Threshold on LDO VLDO Rising l 2.3 VIN Quiescent Current in Shutdown VIN Quiescent Current in Burst Mode Operation FB = 1.4V, Non-Bootstrapped (Note 6) Oscillator Frequency l 1000 TYP 2.5 MAX 40 40 V V 40 V 2.7 V 3 A 50 A 1200 Oscillator Frequency Variation VIN = 12V to 36V Feedback Voltage Measured on FB Feedback Voltage Line Regulation VIN = 2.7V to 40V, Measured on FB 0.2 Error Amplifier Transconductance VC Current = 5A 120 FB Pin Input Current FB = 1V 1400 0.1 l 0.98 UNITS 1.0 1 kHz %/V 1.02 V % S 50 nA VC Source Current VC = 0.6V -12 A VC Sink Current VC = 0.6V 12 A RUN Pin Threshold--Accurate RUN Pin Rising l 1.185 RUN Pin Hysteresis 1.205 1.29 140 Run Pin Threshold--Logic l PROG Current Switch D Current = 1A Switch D Current = 500mA Switch D Current = 100mA (Note 3) PROG Current Gain Ratio of PROG Current to SWD Current Inductor Current Limit (Note 3) 0.3 0.7 1.1 V 38 18 2 40 20 4 42 22 6 A A A 40 PROG Voltage Threshold l V mV A/A 0.90 0.925 0.95 V 1.3 1.7 2.3 A Overload Current Limit VOUT = 0V (Note 3) 2.6 A IZERO Inductor Current Limit (Note 3) 100 mA Maximum Duty Cycle Percentage of Period SW2 is Low in Boost Mode Percentage of Period SW1 is High in Boost Mode l l 95 88 % % Minimum Duty Cycle Percentage of Period SW1 is High in Buck Mode l 90 85 0 % Rev. D For more information www.analog.com 3 LTC3114-1 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25C (Note 2). VIN = 24V, VOUT = 5V, unless otherwise noted. N-Channel Switch Resistance Switch A (from PVIN to SW1) Switch B (from SW1 to PGND) Switch C (from SW2 to PGND) Switch D (from PVOUT to SW2) 250 250 250 250 N-Channel Switch Leakage LDO Output Voltage ILDO = 10mA LDO Load Regulation ILDO = 1mA to 10mA LDO Line Regulation ILDO = 1mA, VIN = 10V to 40V LDO Current Limit VLDO = 2.5V l 4.2 40 SW1 and SW2 Forced Low Time H = PWM Mode, L = Burst Mode Operation Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3114-1 is tested under pulsed load conditions such that TJ TA. The LTC3114E-1 is guaranteed to meet performance specifications from 0C to 85C junction temperature. Specifications over the -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3114I-1 specifications are guaranteed over the -40C to 125C operating junction temperature range. The LTC3114H-1 specifications are guaranteed over the -40C to 150C operating junction temperature range. The LTC3114MP-1 specifications are guaranteed over the -55C to 150C operating junction temperature range. High junction temperatures degrade operating lifetime; operating lifetime is derated for junction temperatures greater than 125C. The maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal resistance and other environmental factors. The junction temperature (TJ in degrees Celsius) is calculated from the ambient temperature (TA in degrees Celsius) and the power dissipation (PD in Watts) according to the following formula: TJ = TA + (PD * JA) where JA is the thermal impedance of the package. 4 0.1 10 4.4 4.6 0.8 Soft-Start Time MODE Pin Logic Threshold m m m m l 0.5 A V % 0.2 % 65 mA 2 ms 100 ns 0.9 1.3 V Note 3: Current measurements are performed when the LTC3114-1 is not switching. The current limit values measured in operation will be somewhat higher due to the propagation delay of the comparators. The LTC3114-1 is tested in a proprietary non-switching test mode. Note 4: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. The maximum rated junction temperature will be exceeded when this protection is active. Continuous operation above the specified absolute maximum operating junction temperature may impair device reliability or permanently damage the device. Note 5: Operating output voltage can be programmed as low as 1.0V nominal if the accurate programmable output current limit feature is not required. Note 6: Connecting LDO/PLDO to the regulated 5V output (bootstrapping), reduces quiescent current substantially. Typical no-load quiescent current for 12V VIN to 5V VOUT is 30A, if boostrapped. Rev. D For more information www.analog.com LTC3114-1 TYPICAL PERFORMANCE CHARACTERISTICS 95 90 90 85 85 80 80 70 65 60 55 40 0.001 75 70 65 60 VIN = 5V VIN = 12V VIN = 24V VIN = 36V 50 45 0.01 0.1 LOAD CURRENT (A) 40 0.001 1 0.01 0.1 LOAD CURRENT (A) 31141 G01 90 OUTPUT CURRENT (A) EFFICIENCY (%) 75 70 VIN = 5V VIN = 12V VIN = 24V VIN = 36V 65 60 0.0001 0.001 0.01 0.1 LOAD CURRENT (A) 70 1 1 1.35 1.25 1.15 1.05 0.95 0.85 0.75 0.65 0.55 0.45 0.35 0.25 0.15 0.05 160 20 VOUT = 5V VOUT = 12V VOUT = 24V 1 10 INPUT VOLTAGE (V) 100 90 80 70 LOAD INCREASING LOAD DECREASING 60 50 1 10 INPUT VOLTAGE (V) 40 31141 G07 120 100 80 60 20 40 VOUT = 5V VOUT = 12V 1 10 INPUT VOLTAGE (V) No-Load Input Current vs VIN, PWM Mode 15 10 5 VOUT = 5V VOUT = 12V 1 10 INPUT VOLTAGE (V) 40 31141 G08 40 31141 G06 OUTPUT CURRENT (mA) INPUT CURRENT (mA) LOAD CURRENT (mA) 110 No-Load Input Current vs VIN, Burst Mode Enabled 40 150 120 40 140 160 140 10 INPUT VOLTAGE (V) 31141 G05 Burst Mode Operation Threshold vs VIN 130 1 31141 G03 Maximum Load Current vs VIN 31141 G04 170 80 75 INPUT CURRENT (A) 95 80 85 31141 G02 24V Output Efficiency vs Load 85 ILOAD = 200mA ILOAD = 400mA ILOAD = 600mA ILOAD = 1A 90 55 VIN = 3.6V VIN = 12V VIN = 24V VIN = 36V 45 95 EFFICIENCY (%) 75 50 12V Output Efficiency vs VIN 12V Output Efficiency vs Load 95 EFFICIENCY (%) EFFICIENCY (%) 5V Output Efficiency vs Load (TA = 25C unless otherwise specified) 760 720 680 640 600 560 520 480 440 400 360 320 280 240 Average Output Current vs VIN, RPROG R = 25k R = 50k R = 100k 1 10 INPUT VOLTAGE (V) 40 31141 G09 Rev. D For more information www.analog.com 5 LTC3114-1 TYPICAL PERFORMANCE CHARACTERISTICS (TA = 25C unless otherwise specified) VIN = 12V 0.75 VIN = 12V RPROG = 64.7k 10 OUTPUT VOLTAGE (V) 0 Output Voltage Load Regulation 0.50 0.25 0 -0.25 -0.50 -1.25 -1.50 -0.1 10 INPUT VOLTAGE (V) 1 7.25 7.00 6.75 6.50 6.25 1 10 INPUT VOLTAGE (V) VIN = 40V LDO DROPOUT VOLTAGE (mV) LDO VOLTAGE (V) 40 4.430 VIN = 5V 0 30 60 90 TEMPERATURE (C) 120 150 31141 G16 6 6.50 6.00 5.50 5.00 4.50 4.00 31141 G15 1.160 ILDO = 5mA 70 60 50 40 30 -60 -30 5.5 4.1 3.4 4.8 LDO, PLDO VOLTAGE (V) 2.7 Oscillator Frequency vs Temperature 4.410 -30 VOUT = 5V 7.50 3.50 OSCILLATOR FREQUENCY (MHz) 80 4.440 1000 7.00 LDO Dropout Voltage vs Temperature 4.460 4.400 -60 8.00 31141 G14 4.490 4.420 8.50 7.50 LDO Voltage vs Temperature 4.450 10 100 LOAD CURRENT (mA) Combined LDO, PLDO Supply Current vs LDO VOUT = 12V 7.75 6.00 40 4.470 1 31141 G12 Combined LDO, PLDO Supply Current vs VIN 31141 G13 4.480 -0.4 0.1 COMBINED LDO, PLDO CURRENT (mA) COMBINED LDO, PLDO CURRENT (mA) CHANGE IN VOUT NORMALIZED TO VIN = 2.7V (%) 8.00 VOUT = 5V VOUT = 12V VOUT = 5V VOUT = 12V 31141 G11 0.3 0 0 -0.3 -2.00 -55 -35 -15 5 25 45 65 85 105 125 145 TEMPERATURE (C) Output Voltage Line Regulation 0.1 0.1 -0.2 -1.00 31141 G10 0.2 0.2 -0.1 -0.75 -1.75 20 CHANGE IN VOUT NORMALIZED TO 100A (%) 1.00 PROG REGULATION VOLTAGE NORMALIZED TO 1V (%) AVERAGE OUTPUT CURRENT (mA) 440 420 400 380 360 340 320 300 280 260 240 220 200 180 160 140 120 100 PROG Regulation Voltage vs Temperature Average Output Current vs VOUT 0 30 60 90 TEMPERATURE (C) 120 150 31141 G17 1.140 1.120 1.100 1.080 1.060 -60 VIN = 3V VIN = 24V VIN = 40V -30 0 30 60 90 TEMPERATURE (C) 120 150 31141 G18 Rev. D For more information www.analog.com LTC3114-1 TYPICAL PERFORMANCE CHARACTERISTICS (TA = 25C unless otherwise specified) RUN Pin Threshold vs Temperature 8 VIN = 24V VIN = 12V 7 RUN PIN CURRENT (A) RUN PIN THRESHOLD (V) 1.228 1.226 1.224 1.222 1.220 1.218 6 5 -30 0 30 60 90 TEMPERATURE (C) 120 -0.32 5 0 10 15 20 25 30 RUN PIN VOLTAGE (V) 0.35 0.33 0.31 0.29 0.27 0.25 0.23 0.21 120 150 1.800 -30 0 30 60 90 TEMPERATURE (C) 1.750 1.725 1.700 1.675 1.650 -60 -30 0 30 60 90 TEMPERATURE (C) 120 31141 G21 2.70 150 VIN = 24V 2.65 2.60 2.55 2.50 2.45 2.40 -60 -30 0 30 60 90 TEMPERATURE (C) 31141 G23 120 150 120 31141 G24 SW1/SW2 Minimum Low Times vs Temperature VIN = 24V 150 120 Inductor Overload Current Limit Threshold vs Temperature 1.775 Inductor Zero Current Threshold vs Temperature SW1/SW2 Minimum Low Times vs LDO 170 VIN = 24V IN APPLICATION 160 109 106 103 114 MINIMUM LOW TIME (ns) 112 MINIMUM LOW TIME (ns) INDUCTOR ZERO CURRENT THRESHOLD (mA) -0.40 -60 VIN = 24V 31141 G22 115 40 INDUCTOR OVERLOAD CURRENT LIMIT THRESHOLD (A) INDUCTOR CURRENT LIMIT THRESHOLD (A) POWER SWITCH RESISTANCE A/D () 0.37 0 30 60 90 TEMPERATURE (C) 35 Inductor Current Limit Threshold vs Temperature VIN = 24V -30 0 31141 G20 Power Switch Resistance vs Temperature 0.19 -60 0.08 -0.24 2 31141 G19 0.39 VIN = 24V 0.16 -0.16 3 0 150 0.24 -0.08 4 1 1.216 -60 0.41 FB Voltage vs Temperature NORMAIZED FB VOLTAGE (% CHANGE FROM 25C) 1.230 RUN Pin Current vs RUN Pin Voltage 108 102 96 150 140 130 120 110 100 100 -60 -30 0 30 60 90 TEMPERATURE (C) 120 150 31141 G25 90 -60 -30 0 30 60 90 TEMPERATURE (C) 120 150 90 2.7 3.4 4.1 4.8 5.5 LDO VOLTAGE (V) 31141 G26 31141 G27 Rev. D For more information www.analog.com 7 LTC3114-1 TYPICAL PERFORMANCE CHARACTERISTICS (TA = 25C unless otherwise specified) Load Transient in Buck Mode, 100mA to 600mA Load Transient in Boost Mode, 100mA to 600mA LOAD CURRENT 500mA/DIV LOAD CURRENT 500mA/DIV VOUT 200mV/DIV VOUT 200mV/DIV VIN = 14V VOUT = 5V 1ms/DIV 31141 G28 1ms/DIV 31141 G29 31141 G31 31141 G30 Output Voltage Ripple in PWM Mode VOUT 20mV/DIV VOUT 100mV/DIV 1ms/DIV VIN = 14V 200s/DIV LOAD = 10mA FRONT PAGE CIRCUIT 5V Output Voltage Response to Fast Line Transient (4V to 28V in 10s) VIN 10V/DIV VOUT 50mV/DIV 8 VOUT 50mV/DIV VIN = 3.6V VOUT = 5V Burst Mode Operation to PWM Mode Output Voltage Response LOAD CURRENT 500mA/DIV Output Voltage Ripple in Burst Mode Operation 50s/DIV 31141 G32 500ns/DIV 31141 G33 Rev. D For more information www.analog.com LTC3114-1 BLOCK DIAGRAM VIN PVIN SW2 SW1 LDO 4.4V PLDO REVERSE BLOCKING LDO PVOUT INDUCTOR ISENSE MA MD MB PGND OUTPUT CURRENT SENSE MC 0.1A - + PGND 10A IZERO LTC3114-1 GATE DRIVERS BST1 IOUT 25k + - BST2 RUN 1.2V VIN 2.1V LDO 2.5V + - + - + - AVERAGE CURRENT AMP + - PWM VOLTAGE ERROR AMP + - MODE PROG 1V FB 1V VC 1.2MHz OSCILLATOR SOFT-START 1V BIAS GENERATOR BANDGAP REFERENCE POR OVERTEMPERATURE PROTECTION GND PGND 31141 BD Rev. D For more information www.analog.com 9 LTC3114-1 PIN FUNCTIONS PGND (Pin 1, Exposed Pad Pin 17): Power Ground Connections. The PGND pin must be electrically connected to a power ground plane in the application. The exposed pad is an additional power ground connection in parallel with Pin 1. Optimal thermal performance requires that the exposed pad be soldered to the PC board and preferably to a ground plane. SW2 (Pin 2): Buck-Boost Converter Power Switch Pin. This pin is connected to one side of the buck-boost inductor. PVOUT (Pin 3): Buck-Boost Converter Power Output. This pin should be connected to a low ESR capacitor of at least 10F. The capacitor should be placed as close to the IC as possible and should have a short return path to PGND. In applications subject to output short circuits through an inductive load, it is recommended that a Schottky diode be installed from ground (anode) to PVOUT (cathode) to limit the extent that PVOUT is driven below ground during the short-circuit transient. RUN (Pin 4): Input to Enable and Disable the IC and Set Custom Input Undervoltage Lockout (UVLO) Thresholds. The RUN pin can be driven by an external logic signal to enable and disable the IC. In addition, the voltage on this pin can be set by a resistive voltage divider connected to the input voltage in order to provide accurate turn-on and turn-off (UVLO) thresholds. The IC is enabled if RUN exceeds 1.2V nominally. Once enabled, the UVLO threshold has built-in hysteresis of approximately 100mV, so turn-off will occur when the voltage on RUN drops to below 1.1V nominally. To continuously enable the IC, RUN can be tied directly to the input voltage up to the absolute maximum rating. PROG (Pin 5): Output Current Programming Pin and Output of the Switch D Current Sense Amplifier. A current proportional to the current in switch D, the buck-boost converter output current, is delivered from PROG. The PROG current magnitude is approximately ISWD/25000. Connect a parallel resistor and capacitor from PROG to 10 GND to generate a voltage proportional to output current. In applications where this voltage is used to control average output current, the resistor value should be set such that the desired average output current produces 1V on PROG and is given by: RPROG() = 1V * 25000 IOUT ( A ) Alternatively, the voltage on PROG can be connected to an A/D converter and used for system diagnostic functions. Refer to the Applications Information section for complete details on how to select the proper values for RPROG and CPROG. VC (Pin 6): Error Amplifier Output. A frequency compensation network must be connected between VC and GND to stabilize the buck-boost converter. Refer to the Applications Information section for details. FB (Pin 7): Feedback Voltage Input. A resistor divider connected to this pin sets the output voltage for the buckboost converter. The nominal FB voltage is 1V. Care should be taken in the routing of the connection to this pin to minimize the possibility of stray coupling from the SW pins. VOUT is determined by the following relationship: VOUT (V)=1+RTOP/RBOT where RTOP is connected from PVOUT to FB and RBOT is connected from FB to GND GND (Pin 8): Signal Ground. This pin is the ground connection for the control circuitry of the IC and must be tied to ground in the application. LDO (Pin 9): Low Voltage Supply Input for the IC Control Circuitry. This pin powers internal IC control circuitry and must be connected to the LDO pin in the application. A 4.7F or larger bypass capacitor must be connected between this pin and ground. Pins LDO and PLDO must be connected together in the application. VIN (Pin 10): LDO Supply Connection. This pin provides power to the internal VCC regulator. Pins VIN and PVIN must be connected together in the application. If the trace connecting VIN and PVIN is of substantial length, a 1F capacitor should be connected from VIN to GND as close to the IC pins as possible. Rev. D For more information www.analog.com LTC3114-1 PIN FUNCTIONS PLDO (Pin 11): Internal LDO Regulator Output. PLDO is the output of the internal linear regulator that generates the LDO rail from VIN. PLDO is also used as the supply connection to the power switch gate drivers. Pins PLDO and LDO must be connected together in the application. BST2 (Pin 12): Flying Capacitor Pin for SW2. This pin must be connected to SW2 through a 68nF capacitor. BST2 is used to generate the gate driver rail for power switch D. Make the PCB trace from BST2 to the boost capacitor as short and direct as possible. BST1 (Pin 13): Flying Capacitor Pin for SW1. This pin must be connected to SW1 through a 68nF capacitor. BST1 is used to generate the gate driver rail for power switch A. Make the PCB trace from BST2 to the boost capacitor as short and direct as possible. PVIN (Pin 14): Power Input for the Buck-Boost Converter. A 10F or larger capacitor must be connected between PVIN and GND as close to the IC as possible. The bypass capacitor ground connection should via directly down to the PCB ground plane. Pins PVIN and VIN must be connected together in the application. SW1 (Pin 15): Buck-Boost Power Converter Switch Pin. This pin is connected to one side of the buck-boost inductor. MODE (Pin 16): Burst Mode/PWM Mode Control Pin. Forcing MODE high causes the IC to operate in continuous fixed frequency PWM mode. The nominal switching frequency in PWM mode is 1.2MHz. Forcing MODE low enables Burst Mode operation. Burst Mode operation improves efficiency at light loads by only activating the buck-boost converter as needed to maintain the nominal regulated output voltage. If MODE is low, the converter will automatically transition to PWM mode if the load current increases. OPERATION INTRODUCTION The LTC3114-1 is a monolithic, current mode, buck-boost DC/DC converter that can operate over a wide voltage range of 2.2V to 40V and provide up to 1A to the load. Internal, low RDS(ON) N-channel DMOS power switches reduce solution complexity and maximize efficiency. A proprietary switch control algorithm allows the buckboost converter to maintain output voltage regulation with input voltages that are above, below or equal to the output voltage. Transitions between the step-up or step-down operating modes are seamless and free of transients and subharmonic switching, making this product ideal for noise sensitive applications. The LTC3114-1 operates at a fixed nominal switching frequency of 1.2MHz, which provides an ideal trade-off between small solution size and high efficiency. Current mode control provides inherent input line voltage rejection, simplified compensation and rapid response to load transients. Burst Mode capability is also included in the LTC3114-1 and is user selected via the MODE input pin. In Burst Mode operation, the LTC3114-1 provides exceptional efficiency at light output loading conditions by operating the converter only when necessary to maintain voltage regulation. At higher loads, the LTC3114-1 automatically switches to fixed frequency PWM mode when Burst Mode operation is selected. For 5V VOUT applications, the quiescent current in Burst Mode operation can be as low as 20A with the internal LDO regulator bootstrapped to the output voltage. If the application requires extremely low noise, continuous PWM operation can also be selected via the MODE pin. The LTC3114-1 also features an accurate RUN comparator threshold with hysteresis. This allows the buck-boost DC/DC converter to turn on and off at user-selected VIN voltage thresholds. With a wide voltage range and programmable output current or monitoring capabilities, the LTC3114-1 is well suited for many demanding power conversion needs. PROGRAMMABLE AVERAGE OUTPUT CURRENT The LTC3114-1 includes the ability to program an accurate average output current from the buck-boost DC/DC converter. Whether the application is driving high power Rev. D For more information www.analog.com 11 LTC3114-1 OPERATION LEDs, charging batteries, a wide compliance range current source or just providing a well controlled current limit, the LTC3114-1 programmable average output current capability delivers high efficiency and maximum flexibility. The output current limit level is independent of operating mode, (buck or boost), and is active down to approximately 2V on VOUT. Below 2V on VOUT, a secondary foldback current limit circuit is activated to reduce power dissipation. The desired average output current level is programmed with a standard low wattage resistor from PROG to ground. A low loss current sense resistor and accurate current sense amplifier are integrated within the IC, greatly simplifying the PCB layout and design. Factory trimming of the output current limit offset and gain provide a high degree of accuracy, typically within 5% of the setpoint. The applications section provides details on how to select the programming resistor, RPROG, for the desired average output current level from the LTC3114-1. improved loop stability and lower output voltage ripple in comparison to the traditional buck-boost converter. Figure1 shows the topology of the LTC3114-1 power stage which is comprised of four N-channel DMOS switches and their associated gate drivers. In PWM mode operation both switch pins transition on every cycle independent of the input and output voltages. In response to the internal control loop command, an internal pulse width modulator generates the appropriate switch duty cycle to maintain regulation of the output voltage. When stepping down from a high input voltage to a lower output voltage, the converter operates in buck mode and switch D remains on for the entire switching cycle except for the minimum switch low duration (typically 50ns). During the switch low duration, switch C is turned on which forces SW2 low and charges the flying capacitor, CBST2. This ensures that the switch D gate driver power supply rail on BST2 is maintained. The duty cycle of switches A and B are adjusted by the PWM to maintain output voltage regulation in buck mode. PWM Mode Operation If the MODE pin is high or if the load current on the converter is high enough to command PWM mode operation with MODE low, the LTC3114-1 operates in a fixed 1.2MHz PWM mode using a current mode control loop. PWM mode minimizes output voltage ripple and yields a low noise switching frequency spectrum. A proprietary switching algorithm provides seamless transitions between operating modes and eliminates discontinuities in the average inductor current, inductor ripple current and loop transfer function throughout all modes of operation. These advantages result in increased efficiency, CBST1 BST1 If the input voltage is lower than the output voltage, the converter operates in boost mode. Switch A remains on for the entire switching cycle except for the minimum switch low duration (typically 100ns). During the switch low duration, switch B is turned on which forces SW1 low and charges the flying capacitor, CBST1. This ensures that the switch A gate driver power supply rail on BST1 is maintained. The duty cycle of switches C and D are adjusted by the PWM to maintain output voltage regulation in boost mode. CBST2 L PVIN SW1 BST2 SW2 PVOUT PLDO PLDO A D LTC3114-1 PLDO B PGND PLDO C PGND 31141 F01 Figure1. Power Stage Schematic 12 Rev. D For more information www.analog.com LTC3114-1 OPERATION Oscillator divider connected to the FB pin and provides an output, VC, that is used by the current mode control loop to command the appropriate inductor current level. To ensure stability, external frequency compensation components (CP1, CP2 and RZ) must be installed between VC and ground. The procedure for determining these components is provided in the Applications Information section of this data sheet. VC is internally connected to the noninverting input of a high gain, integrating, operational amplifier, referred to in Figure2, as the average current amp. The inverting input of the average current amplifier is connected to the inductor current sense circuit through a gain setting resistor (RCS1) and to its output (VIA) through an internal frequency compensation network comprised of RCS2, CCS1 and CCS2. The average current amplifier's output provides the cycle-by-cycle duty cycle command into the buck-boost PWM circuitry. The LTC3114-1 operates from an internal oscillator with a nominal fixed frequency of 1.2MHz. This allows the DC/DC converter efficiency to be maximized while still using small external components. Current Mode Control The LTC3114-1 utilizes average current mode control for the pulse width modulator as shown in Figure2. Current mode control, both average and the better known peak method, enjoy some benefits compared to other control methods including: simplified loop compensation, rapid response to load transients and improved rejection of line voltage transients. Referring to Figure2, an internal high gain transconductance error amplifier monitors VOUT through a voltage RA 250m VDS SENSE VIN L1 SWA SWD PVOUT VDS SENSE VOUT COUT SWC RCOESR SWB RLOAD INDUCTOR ISENSE gm = 111A/V RX CCS2 C D RCS2 PWM CONTROL LOGIC VIA AVERAGE CURRENT AMP RTOP CCS1 + - B ACTIVE RANGE OF VC = 135mV TO 1V + - A RCS1 RBOT FB gm 1V VOLTAGE ERROR gm = 120S AMP RO = 3.6M VC SOFT-START 1V RZ GND CP1 CP2 31141 F02 Figure2. Average Current Mode Control Loop Rev. D For more information www.analog.com 13 LTC3114-1 OPERATION The noninverting reference level input to the average current amplifier is VC and the feedback or inverting input is driven from the inductor current sensing circuitry. The inductor current sensing circuitry alternately measures the current through switches A and B. The output of the sensing circuitry produces a voltage across resistor RX that resembles the inductor current waveform transformed to a voltage. If there is an increase in the power converter load on VOUT, the instantaneous level of VOUT will drop slightly, which will increase the voltage level on VC by the inverting action of the voltage error amplifier. When the increase on VC first occurs, the output of the current averaging amplifier, VIA, will also increase momentarily to command a larger duty cycle. This duty cycle increase will result in a higher inductor current level, ultimately raising the average voltage across RX. Once the average value of the voltage on RX is equivalent to the VC level, the voltage on VIA will revert very closely to its previous level into the PWM and force the correct duty cycle to maintain voltage regulation at this new higher inductor current level. The average current amplifier is configured as an integrator, so in steady state, the average value of the voltage applied to its inverting input (voltage across RX) will be equivalent to the voltage on its noninverting, VC. As a result, the average value of the inductor current is controlled in order to maintain voltage regulation. The entire current amplifier and PWM can be simplified as a voltage controlled current source, with the driving voltage coming from VC. VC is commonly referred to as the current command for this reason and the voltage on VC is directly proportional to average inductor current, which can prove useful for many applications. The voltage error amplifier monitors the output voltage, VOUT through a voltage divider and makes adjustments to the current command as necessary to maintain regulation. The voltage error amplifier therefore controls the outer voltage regulation loop. The average current amplifier makes adjustments to the inductor current as directed by the voltage error amplifier output via VC and is commonly referred to as the inner current-loop amplifier. The average current mode control technique is similar to peak current mode control except that the average current amplifier, by virtue of its configuration as an integrator, 14 controls average current instead of the peak current. This difference eliminates the peak to average current error inherent to peak current mode control, while maintaining most of the advantages inherent to peak current modecontrol. Average current mode control requires appropriate compensation for the inner current loop unlike peak current mode control. The compensation network must have high DC gain to minimize errors between the commanded average current level and actual, high bandwidth to quickly change the commanded current level following transient load steps and a controlled mid-band gain to provide a form of slope compensation unique to average current mode control. Fortunately, the compensation components required to ensure these sometimes conflicting requirements have been carefully selected and are integrated within the LTC3114-1. With the inner loop compensation fixed internally, compensation of the outer voltage loop as is detailed in the applications section, is similar to well known techniques used with peak current mode control. Inductor Current Sense and Maximum Output Current As part of the current control loop required for current mode control, the LTC3114-1 includes a pair of current sensing circuits that directly measure the buck-boost converter inductor current as shown in Figure2. These circuits measure the voltage dropped across switches A and B separately and produce output currents proportional to the switches' voltage drop. By sensing current in this manner, there is no additional power loss incurred, which improves converter efficiency. The amplifier output terminals are summed together into a common resistor, RX connected to ground. Since switches A and B are never conducting at the same time, the resultant waveform on RX resembles the inductor current. This replica of the inductor current is used as one input to the current averaging amplifier as described in the previous section. The voltage error amplifier output, VC, is internally clamped to a nominal level of 1V. Since the average inductor current is proportional to VC, the 1V clamp level sets the maximum average inductor current that can be programmed by the inner current loop. Taking into account the current sense amplifier's gain and the value of RX, the Rev. D For more information www.analog.com LTC3114-1 OPERATION maximum average inductor current is approximately 1.7A (typical). In buck mode, the output current is approximately equal to the inductor current, IL. IOUT(BUCK) IL * 0.9 The SW1/SW2 forced low time on each switching cycle briefly disconnects the inductor from VOUT and VIN resulting in slightly less output current in either buck or boost mode for a given inductor current. In boost mode, the output current is related to average inductor current and duty cycle by: At VC levels below 135mV, the LTC3114-1 will not command any current because the internal current sense signal has a built-in 135mV offset. Therefore, the active range of VC is between approximately 135mV (zero current) and 1V (full current). In some applications, an external circuit may be used to control the VC voltage level. Any such circuit needs to have the capability to sink or source the approximate 12A provided by the internal error amplifier and to pull below 135mV to disable the current command, if necessary. OVERLOAD CURRENT LIMIT AND ZERO CURRENT COMPARATOR IOUT(BOOST) IL * (1 - D) where D is the converter duty cycle. Since the output current in boost mode is reduced by the duty cycle (D), the output current rating in buck mode is always greater than in boost mode. Also, because boost mode operation requires a higher inductor current for a given output current compared to buck mode, the efficiency in boost mode will be lower due to higher IINDUCTOR2 * RDS(ON) losses in the power switches. This will further reduce the output current capability in boost mode. In either operating mode, however, the inductor peak-to-peak ripple current does not play a major role in determining the output current capability, unlike peak current mode control. With peak current mode control, the maximum output current capability is reduced by the magnitude of inductor ripple current because the peak inductor current level is the control variable, but the average inductor current is what determines the output current. The LTC3114 -1 measures and controls average inductor current, and therefore, the inductor ripple current magnitude has little effect on the maximum current capability in contrast to an equivalent peak current mode converter. Under most conditions in buck mode, the LTC3114 -1 is capable of providing 1A to the load. Under certain conditions, more output current is possible, refer to the Typical Performance Characteristics section for more details. In boost mode, as described previously, the output current capability is related to the boost ratio or duty cycle (D). For a 3.6V VIN to 5V output application, the LTC3114-1 can provide up to 500mA to the load. Refer to the Typical Performance Characteristics section for more detail on output current capability. The internal current sense waveform is also used by the peak overload current (IPEAK) and zero current (IZERO) comparators. The IPEAK current comparator monitors ISENSE and halts converter operation if the inductor current level exceeds its maximum internal threshold, which is approximately 50% above the normal maximum current level commanded by the current control loop. An inductor current level of this magnitude will only occur during a fault, such as an output short circuit or a fast VIN (line) transient. If the IPEAK comparator is engaged, the PWM is halted for the remainder of the switching cycle with SW1 and SW2 held low. If VOUT is less than approximately 1.8V when the peak limit occurs, then a soft-start cycle is initiated. In the event that the current overload is the result of an output short-circuit condition, the LTC31141 will remain in a low frequency restart mode, keeping the on-chip power dissipation to very low levels. If the short circuit is removed, the LTC3114-1 will restart in the normal fashion. The LTC3114-1 exhibits discontinuous inductor current operation at light output loads by virtue of the IZERO comparator circuit under most operating conditions. This improves efficiency at light output loads if PWM mode operation compared to continuous conduction mode. If the internal current sense waveform transitions below the internally set zero current threshold, the LTC3114-1 will disconnect the inductor from VOUT, by shutting off switch D, to prevent discharge of the output capacitor. The IZERO circuitry is reset by the oscillator clock at the end of the switching cycle. The IZERO comparator threshold is set Rev. D For more information www.analog.com 15 LTC3114-1 OPERATION slightly above zero current to compensate for comparator propagation delay. In some cases, the inductor current may reverse slightly if there is a very high voltage output or small inductor resulting in a small amount of residual energy left in the inductor following a zero current event. In this case the LTC3114-1 SW1 waveform will display a characteristic half sine wave between the time at which Izero is detected and when the next switching cycle commences. This is because SWC is the only active (on) switch following an IZERO event and this behavior is not harmful to the LTC3114-1. LDO REGULATOR Burst Mode Operation When the MODE pin is held low, the LTC3114-1 is configured for Burst Mode operation. As a result, the buck-boost DC/DC converter will operate with normal continuous PWM switching above a predetermined minimum output load and will automatically transition to power saving Burst Mode operation below this output load level. Refer to the Typical Performance Characteristics section of this data sheet to determine the Burst Mode transition threshold for various combinations of VIN and VOUT. If MODE is low, at light output loads, the LTC3114-1 will go into a standby or sleep state when the output voltage achieves its nominal regulation level. The sleep state halts PWM switching and powers down all non-essential functions of the IC, significantly reducing the quiescent current of the LTC3114-1. This greatly improves overall power conversion efficiency when the output load is light. Since the converter is not operating in sleep, the output voltage will slowly decay at a rate determined by the output load resistance and the output capacitor value. When the output voltage has decayed by a small amount, typically 1%, the LTC3114-1 will wake and resume normal PWM switching operation until the voltage on VOUT is restored to the previous level. If the load is very light, the LTC31141 may only need to switch for a few cycles to restore VOUT and may sleep for extended periods of time, significantly improving efficiency. Soft-Start The LTC3114-1 soft-start circuit minimizes input current transients and output voltage overshoot on initial power 16 up. The required timing components for soft-start are internal to the LTC3114-1 and produce a nominal softstart duration of approximately 2ms. The internal softstart circuit slowly ramps the error amplifier output, VC. In doing so, the current command of the IC is also slowly increased, starting from zero. It is unaffected by output loading or output capacitor value. Soft-start is reset by undervoltage lockout on both VIN and LDO, the accurate RUN pin comparator, thermal shutdown and the overload current limit as described previously. An internal low dropout regulator generates a nominal 4.4V rail from VIN. The LDO rail powers the internal control circuitry and power device gate drivers of the LTC31141. The LDO regulator is disabled in shutdown to reduce quiescent current and is enabled by forcing the RUN pin above its logic threshold. The LDO regulator includes current-limit protection to safeguard against accidental short-circuiting of the LDO rail. In 5V VOUT applications, the LDO can be driven by VOUT through a Schottky diode, commonly referred to as bootstrapping. Bootstrapping can provide a significant efficiency improvement, particularly when VIN is very high and also allows operation to the minimum rated input voltage of 2.2V. UNDERVOLTAGE LOCKOUT The LTC3114-1 undervoltage lockout (UVLO) circuit disables operation of the internal power switches and keeps other IC functions in a reset state if either the input voltage applied to VIN or the LDO output voltage are below their respective UVLO thresholds. There are two UVLO circuits, one that monitors VIN and another that monitors LDO. The VIN UVLO comparator has a falling voltage threshold of 2.1V (typical). If VIN falls below this level, IC operation is disabled until VIN rises above 2.2V (typical), as long as the LDO voltage is above its UVLO threshold. The LDO UVLO has a falling voltage threshold of 2.4V (typical). If the LDO voltage falls below this threshold, IC operation is disabled until LDO rises above 2.5V (typical) as long as VIN is above its nominal UVLO threshold level. Rev. D For more information www.analog.com LTC3114-1 OPERATION Depending on the particular application, either of these UVLO thresholds could be the limiting factor affecting the minimum input voltage required for operation. The LTC3114-1 LDO regulator uses VIN for its power input. If LDO is not bootstrapped, then there exists a voltage drop or dropout voltage between VIN and LDO. The dropout voltage is proportional to the loading on LDO, which is primarily due to the gate charge and capacitive charging currents inherent to the internal power switches. The loading on LDO and the LDO dropout voltage, therefore, are proportional to VIN and VOUT. For this reason, the minimum input voltage required for operation is limited by the LDO minimum voltage as input voltage (VIN) will always be higher than LDO in the normal (non-bootstrapped) configuration. The Typical Performance Characteristics section of this data sheet provides guidance on the dropout voltage between VIN and LDO over the range of VIN and VOUT. In applications where LDO is bootstrapped (powered by VOUT through a Schottky diode or auxiliary power rail), the minimum input voltage for operation (after start-up) will be limited only by the VIN UVLO threshold (2.1V typical). Please note that if the bootstrap voltage is derived from the LTC3114-1 VOUT and not an independent power rail, then the minimum input voltage required for initial start-up is still limited by the minimum LDO voltage (2.6V typical). RUN PIN COMPARATOR In addition to serving as a logic-level input to enable certain functions of the IC, the RUN pin includes an accurate internal comparator that allows it to be used to set custom rising and falling on/off thresholds with the addition of an external resistor divider. When RUN is driven above its logic threshold (0.7V typical), the LDO regulator is enabled, which provides power to the internal control circuitry of the IC. If the voltage on RUN is increased further so that it exceeds the RUN comparator accurate analog threshold (1.2V nominal), all functions of the buckboost converter will be enabled and a startup sequence will ensue. VIN LTC3114-1 R1 RUN ACCURATE THRESHOLD 1.2V - + ENABLE SWITCHING 0.7V - + ENABLE LDO AND CONTROL CIRCUITS R2 LOGIC THRESHOLD 31141 F03 Figure3. Accurate RUN Pin Comparator If RUN is brought below the accurate comparator threshold, the buck-boost converter will inhibit switching, but the LDO regulator and control circuitry will remain powered unless RUN is brought below its logic threshold. Therefore, in order to completely shut down the IC and reduce the VIN current to 3A (typical), it is necessary to ensure that RUN is brought below its worst-case lowlogic threshold of 0.3V. RUN is a high voltage input and can be tied directly to VIN to continuously enable the IC when the input supply is present. Also note that RUN can be driven above VIN or VOUT as long as it stays within the operating range of the IC, that is, less than 40V. If RUN is forced above 5V, it will sink a small current as given by the following equation: IRUN VRUN - 5V 5M With the addition of an optional resistor divider as shown in Figure 3, the RUN pin can be used to establish a user-programmable turn on and turn off threshold. The buck-boost converter is enabled when the voltage on RUN reaches 1.205V (nominal). Therefore, the turn-on voltage threshold on VIN is given by: R1 VTURNON = 1.205V 1+ R2 Once the converter is enabled, the RUN comparator includes a built-in hysteresis of approximately 140mV, so that the turn-off threshold will be approximately 8.33% lower than the turn-on threshold. Put another way, the internal threshold level for the RUN comparator looks like 1.1V after the IC is enabled. Rev. D For more information www.analog.com 17 LTC3114-1 OPERATION The RUN comparator is relatively noise insensitive, but there may be cases dues to PCB layout, very large value resistors for R1 and R2 or proximity to noisy components where noise pickup is unavoidable and may cause the turn on or turn off of the IC to be intermittent. In these cases, a filter capacitor can be added across R2 to ensure proper operation. THERMAL CONSIDERATIONS The power switches of the LTC3114-1 are designed to operate continuously with currents up to the internal current limit thresholds. However, when operating at high current levels, there may be significant heat generated within the IC. In addition, the LDO regulator can generate a significant amount of heat when VIN is very high. This adds to the total power dissipation of the IC. As described elsewhere in this data sheet, bootstrapping of the LDO for 5V output applications can essentially eliminate the LDO power dissipation term and significantly improve efficiency. As a result, careful consideration must be given to the thermal environment of the IC in order to provide a means to remove heat from the IC and ensure that the LTC3114-1 is able to provide its full rated output current. Specifically, the exposed die attach pad of both the DHC and FE packages must be soldered to a copper layer on the PCB to maximize the conduction of heat out of the IC package. This can be accomplished by utilizing multiple vias from the die attach pad connection underneath the IC package to other PCB layer(s) containing a large copper plane. A typical board layout incorporating these concepts is shown in Figure4. Start-Up Into a Pre-Biased VOUT Some applications require the LTC3114-1 to start up into an output voltage (VOUT), that is pre-biased by an external source to some level. It is desirable at LTC3114-1 start-up to minimize current taken from the pre-bias voltage source and VOUT storage capacitor to prevent VOUT glitches and currents fed backwards into the VIN power source of the LTC3114-1. If the LTC3114-1 VIN voltage is higher than the pre-biased VOUT, indicating buck mode operation, then there will be minimal reverse current at start-up. However, if the LTC3114-1 VIN voltage is lower than the pre-biased VOUT, indicating boost mode operation, then it is possible for a brief, but substantial reverse current to be taken by the LTC3114-1 from VOUT. The duration of this reverse current is approximately 100s to 200s. The magnitude is inversely proportional to the VIN voltage and dependent upon external component values. Prevention of pre-biased VOUT reverse current in boost mode can be achieved in two ways. The preferred method is to ensure that the pre-biased VOUT voltage level is set higher than the nominal VOUT regulation level. For example, if VOUT is pre-biased to 13V, then setting the VOUT regulation voltage of the LTC3114-1 to less than 13V, taking into account error margins, will result in negligible or zero reverse current at start-up. If this is not possible, then a Schottky diode can be connected in series between VOUT of the LTC3114-1 and the converter output to block reverse current . If the IC die temperature exceeds approximately 165C, overtemperature shutdown will be invoked and all switching will be inhibited. The part will remain disabled until the die temperature cools by approximately 10C. The softstart circuit is re-initialized in overtemperature shutdown to provide a smooth recovery when the IC die temperature cools enough to resume operation. 18 Rev. D For more information www.analog.com LTC3114-1 OPERATION Top Layer 2nd Layer Bottom Layer 3rd Layer Figure4. Typical 4 Layer PC Board Layout Rev. D For more information www.analog.com 19 LTC3114-1 APPLICATIONS INFORMATION A standard application circuit for the LTC3114-1 is shown on the front page of this data sheet. The appropriate selection of external components is dependent upon the required performance of the IC in each particular application given considerations and trade-offs such as PCB area, input and output voltage range, output voltage ripple, required efficiency, thermal considerations and cost. This section of the data sheet provides some basic guidelines and considerations to aid in the selection of external components and the design of the applications circuit. LDO Capacitor Selection The LDO output of the LTC3114-1 is generated from VIN by a low dropout linear regulator. The LDO regulator has been designed for stable operation with a wide range of output capacitors. For most applications, a low ESR capacitor of at least 4.7F should be used. The capacitor should be located as close to the PLDO pin as possible and connected to the LDO pin and ground through the shortest traces possible. PLDO is the regulator output and is also the internal supply pin for the gate drivers and boost rail charging diodes. The LDO pin is the supply connection for the remainder of the control circuitry. The LDO and PLDO pins must be connected together on the PCB. If the connecting trace cannot be made short, an additional 0.1F bypass capacitor should be connected between the LDO pin and ground as close to the package pins as possible. Inductor Selection The choice of inductor used in LTC3114-1 application circuits influences the maximum deliverable output current, the converter bandwidth, the magnitude of the inductor current ripple and the overall converter efficiency. The inductor must have a low DC series resistance or output current capability and efficiency will be compromised. Larger inductor values reduce inductor current ripple but will not increase output current capability as is the case with peak current mode control as described in the Maximum Output Current section of this data sheet. Larger value inductors also tend to have a higher DC series resistance for a given case size, which will have a negative impact on efficiency. Larger values of inductance will also lower the right half plane (RHP) zero frequency when operating in boost mode, which requires the converter bandwidth to 20 be set lower in frequency, slowing the converter's response to load transients. Nearly all LTC3114-1 application circuits deliver the best performance with an inductor value between 4.7H and 15H. Buck mode-only applications can use the larger inductor values as they are unaffected by the RHP zero, while mostly boost applications generally require inductance on the low end of this range depending on how deep they will operate in boost mode. Regardless of inductor value, the saturation current rating should be selected such that it is greater than the worst-case average inductor current plus half of the ripple current. The peak-to-peak inductor current ripple for each operational mode can be calculated from the following formula, where f is the switching frequency (1.2MHz), L is the inductance in H and tLOW is the switch pin minimum low time in s. The switch pin minimum low time is typically 0.05s. IL(P-P)(BUCK) = VOUT VIN - VOUT 1 - tLOW Amps L VIN f IL(P-P)(BOOST) = VIN VOUT - VIN 1 - tLOW Amps L VOUT f It should be noted that the worst-case inductor peak-topeak inductor ripple current occurs when the duty cycle in buck mode is maximum (highest VIN) and in boost mode when the duty cycle is 50% (VOUT = 2 * VIN). As an example, if VIN (minimum) = 3.6V and VIN (maximum) = 40V, VOUT = 5V and L = 6.8H, the peak-to-peak inductor ripples at the voltage extremes (40V VIN for buck and 3.6V VIN for boost) are: Buck = 504mA peak-to-peak Boost = 116mA peak-to-peak One-half of this inductor ripple current must be added to the highest expected average inductor current in order to select the proper saturation current rating for the inductor. In addition to its influence on power conversion efficiency, the inductor DC resistance can also impact the maximum output current capability of the buck-boost converter particularly at low input voltages. In buck mode, the output current of the buck-boost converter is primarily limited by the inductor current reaching the average current limit Rev. D For more information www.analog.com LTC3114-1 APPLICATIONS INFORMATION threshold defined by VC. However, in boost mode, especially at large step-up ratios, the output current capability can also be limited by the total resistive losses in the power stage. These losses include, switch resistances, inductor DC resistance and PCB trace resistance. Avoid inductors with a high DC resistance (DCR) as they can degrade the maximum output current capability from what is shown in the Typical Performance Characteristics section and from the Typical Application circuits. As a guideline, the inductor DCR should be significantly less than the typical power switch resistance of 250m. The only exceptions are applications that have a maximum output current much less than what the LTC3114-1 is capable of delivering. Different inductor core materials and styles have an impact on the size and price of an inductor at any given current rating. Shielded construction is generally preferred as it minimizes the chances of interference with other circuitry. The choice of inductor style depends upon the price, sizing, and EMI requirements of a particular application. Table1 provides a small sampling of inductors that are well suited to many LTC3114-1 applications. Output Capacitor Selection A low effective series resistance (ESR) output capacitor should be connected at the output of the buck-boost converter in order to minimize output voltage ripple. Multilayer ceramic capacitors are an excellent option as they have low ESR and are available in small footprints. The capacitor value should be chosen large enough to reduce the output voltage ripple to acceptable levels. Neglecting the capacitor's ESR and ESL (effect series inductance), the peak-to-peak output voltage ripple can be calculated by the following formula, where f is the frequency in MHz (1.2MHz for the LTC3114 -1), COUT is the capacitance in F, tLOW is the switch pin minimum low time in us (0.1s for the LTC3114-1) and ILOAD is the output current in Amps. VP-P(BUCK) = ILOADtLOW Volts COUT VP-P(BOOST) = ILOAD VOUT - VIN + tLOW fVIN Volts fCOUT VOUT Table1. Representative Surface Mount Inductors PART NUMBER VALUE DCR MAX DC (H) (m) CURRENT (A) SIZE (mm) WxLxH Coilcraft LPS6225 LPS6235 MSS1038 D03316P 4.7 6.8 22 15 65 75 70 50 3.2 2.8 3.3 3.0 6.2 x 6.2 x 2.5 6.2 x 6.2 x 3.5 10.2 x 10.5 x 3.8 12.9 x 9.4 x 5.2 Cooper-Bussmann CD1-150-R DR1030-100-R FP3-8R2-R DR1040-220-R 15 10 8.2 22 50 40 74 54 3.6 3.18 3.4 2.9 10.5 x 10.4 x 4.0 10.3 x 10.5 x 3.0 7.3 x 6.7 x 3.0 10.3 x 10.5 x 4.0 Panasonic ELLCTV180M ELLATV100M 18 10 30 23 3.0 3.3 12 x 12 x 4.2 10 x 10 x 4.2 Sumida CDRH8D28/HP CDR10D48MNNP CDRH8D28NP 10 39 4.7 78 105 24.7 3.0 3.0 3.4 8.3 x 8.3 x 3 10.3 x 10.3 x 5 8.3 x 8.3 x 3 Taiyo-Yuden NR10050T150M 15 46 3.6 9.8 x 9.8 x 5 TOKO B1047AS-6R8N B1179BS-150M 892NAS-180M 6.8 15 18 36 56 42 2.9 3.3 3.0 7.6 x 7.6 x 5 10.3 x 10.3 x 4 12.3 x 12.3 x 4.5 Wurth 7447789004 7440650068 744771133 744066150 4.7 6.8 33 15 33 33 49 40 2.9 3.6 2.7 3.2 7.3 x 7.3 x 3.2 10 x 10 x 3 12 x 12 x 6 10 x 10 x 3.8 Examining the previous equations reveal that the output voltage ripple increases with load current and is generally higher in boost mode than in buck mode. Note that these equations only take into account the voltage ripple that occurs from the inductor current to the output being discontinuous. They provide a good approximation to the ripple at any significant load current but underestimate the output voltage ripple at very light loads where the output voltage ripple is dominated by the inductor current ripple. In addition to the output voltage ripple generated across the output capacitance, there is also output voltage ripple produced across the internal resistance of the output capacitor. The ESR-generated output voltage ripple is proportional to the series resistance of the output capacitor and is given by the following expressions where RESR is Rev. D For more information www.analog.com 21 LTC3114-1 APPLICATIONS INFORMATION the series resistance of the output capacitor and all other terms as previously defined. VP-P(BUCK) = ILOADRESR I R Volts 1- tLOW f LOAD ESR VP-P(BOOST) = V ILOADRESRVOUT ILOADRESR OUT Volts VIN (1- tLOW f ) VIN In most LTC3114-1 applications, an output capacitor between 10F and 22F will work well. Input Capacitor Selection The PVIN pin carries the full inductor current and provides power to internal control circuits in the IC. To minimize input voltage ripple and ensure proper operation of the IC, a low ESR bypass capacitor with a value of at least 6.8F should be located as close to the pin as possible. The traces connecting this capacitor to PVIN and the ground plane should be made as short as possible. The VIN pin provides power to the LDO regulator and other internal circuitry. If the PCB trace connecting PVIN to VIN is long, it is recommended to add an additional small 0.1F bypass capacitor near the VIN pin. When powered through long leads or from a high ESR power source, a larger value bulk input capacitor may be required. In such applications, a 47F to 100F electrolytic capacitor in parallel with a 1F ceramic capacitor generally yields a high performance, low cost solution. Recommended Input and Output Capacitors The capacitors used to filter the input and output of the LTC3114-1 must have low ESR and must be rated to handle the large AC currents generated by the switching converters. This is important to maintain proper functioning of the IC and to reduce output voltage ripple. There are many capacitor types that are well suited to these applications including multilayer ceramic, low ESR tantalum, OS-CON and POSCAP technologies. In addition, there are certain types of electrolytic capacitors such as solid aluminum organic polymer capacitors that are designed for low ESR and high AC currents and these are also well suited to some LTC3114-1 applications. Table2 provides a partial listing of appropriate capacitors to use with the LTC31141. The 22 Table2. Representative Bypass and Output Capacitors MANUFACTURER, PART NUMBER AVX 12103D226MAT2A VALUE (F) VOLTAGE (V) SIZE L x W x H (mm), TYPE, ESR 22 25 TPME226K050R0075 22 50 3.2 x 2.5 x 2.79 X5R Ceramic 7.3 x 4.3 x 4.1 Tantalum, 75m Kemet C2220X226K3RACTU 22 25 A700D226M016ATE030 22 16 Murata GRM32ER71E226KE15L 22 25 3.2 x 2.5 x 2.5 X7R Ceramic Nichicon PLV1E121MDL1 82 25 8 x 8 x 12 Alum. Polymer, 25m Panasonic ECJ-4YB1E226M 22 25 3.2 x 2.5 x 2.5 X5R Ceramic Sanyo 25TQC22MV 22 25 16TQC100M 100 16 25SVPF47M 47 25 7.3 x 4.3 x 3.1 POSCAP, 50m 7.3 x 4.3 x 1.9 POSCAP, 45m 6.6 x 6.6 x 5.9 OS-CON, 30m Taiyo Yuden UMK325BJ106MM-T 10 50 TMK325BJ226MM-T 22 25 TDK KTJ500B226M55BFT00 22 50 C5750X7R1H106M 10 50 CKG57NX5R1E476M 47 25 Vishay 94SVPD476X0035F12 47 35 5.7 x 5.0 x 2.4 X7R Ceramic 7.3 x 4.3 x 2.8 Alum. Polymer, 30m 3.2 x 2.5 x 2.5 X5R Ceramic 3.2 x 2.5 x 2.5 X5R Ceramic 6.0 x 5.3 x 5.5 X7R Ceramic 5.7 x 5.0 x 2.0 X7R Ceramic 6.5 x 5.5 x 5.5 X5R Ceramic 10.3 x 10.3 x 12.6 OS-CON, 30m choice of capacitor technology is primarily dictated by a trade-off between size, leakage current and cost. In backup power applications, the input or output capacitor might be a super or ultra capacitor with a capacitance value measuring in the Farad range. The selection criteria in these Rev. D For more information www.analog.com LTC3114-1 APPLICATIONS INFORMATION applications are generally similar except that voltage ripple is generally not a concern. Some capacitors exhibit a high DC leakage current which may preclude their consideration for applications that require a very low quiescent current in Burst Mode operation. Ceramic capacitors are often utilized in switching converter applications due to their small size, low ESR and low leakage currents. However, many ceramic capacitors intended for power applications experience a significant loss in capacitance from their rated value as the DC bias voltage on the capacitor increases. It is not uncommon for a small surface mount capacitor to lose more than 50% of its rated capacitance when operated near its maximum rated voltage. This effect is generally reduced as the case size is increased for the same nominal value capacitor. As a result, it is often necessary to use a larger value capacitance or a higher voltage rated capacitor than would ordinarily be required to actually realize the intended capacitance at the operating voltage of the application. X5R and X7R dielectric types are recommended as they exhibit the best performance over the wide operating range and temperature of the LTC3114-1. To verify that the intended capacitance is achieved in the application circuit, be sure to consult the capacitor vendor's curve of capacitance versus DC bias voltage. Programming Custom VIN Turn-On and Turn-Off Thresholds approximately 8.33% of the programmed turn-on threshold level given in the previous equation. Bootstrapping the LDO Regulator The high and low side gate drivers are powered through the PLDO rail, which is generated from the input voltage, VIN, through an internal linear regulator. In some applications, especially at high input voltages, the power dissipation in the linear regulator can become a major contributor to thermal heating of the IC. The Typical Performance Characteristics section of this data sheet provides data on the LDO/PLDO current and resulting power loss versus VIN and VOUT. A significant performance advantage can be attained in applications where converter output voltage (VOUT) is programmed to 5V, if VOUT is used to power the LDO/PLDO rails. Powering the LDO/PLDO rails in this manner is referred to as bootstrapping. This can be done by connecting a Schottky diode from VOUT to LDO/PLDO as shown in Figure5. With the bootstrap diode installed, the gate driver currents are supplied by the buck-boost converter at high efficiency rather than through the internal linear regulator. The internal linear regulator contains reverse blocking circuitry that allows LDO/PLDO pins to be driven slightly above their nominal regulation level with only a very slight amount of reverse current. Please note that the bootstrapping supply (either VOUT or a separate regulator) must be limited to less than 5.7V. With the addition of an external resistor divider connected to the input voltage as shown in Figure3, the RUN pin can be used to program the input voltage at which the LTC3114-1 is enabled and disabled. For a rising input voltage, the LTC3114-1 is enabled when VIN reaches the threshold given by the following equation, where R1 and R2 are the values of the resistor divider resistors specified in k: R1+ R2 VTH(RISING) = 1.2 Volts R2 Once the IC is enabled, it will remain so until the input voltage drops below the comparator threshold by the hysteresis voltage of approximately 100mV, measured on the RUN pin. Therefore, the amount of hysteresis is PVOUT VOUT LTC3114-1 LDO PLDO 4.7F 31141 F05 Figure5. Bootstrapping PLDO and LDO Average Output Current Limit Programming The LTC3114-1 includes an average output current programming feature that transforms the LTC3114-1 into a wide voltage compliance range, high efficiency, constant current source. A resistor from PROG to ground programs the desired level of average output current up to 1A. Potential uses include high brightness LED driving and constant current battery or capacitor charging. Rev. D For more information www.analog.com 23 LTC3114-1 APPLICATIONS INFORMATION A simplified diagram of the average output current programming circuitry is shown in the Block Diagram. An internal sense resistor, RS, and low offset amplifier directly measure current in the VOUT path and produce a small fraction of this current out of the PROG pin. Accordingly, a resistor and filtering capacitor connected from PROG to ground produce a voltage proportional to average output current on PROG. An internal transconductance amplifier compares the PROG voltage to the fixed 1V internal reference. If the PROG voltage tries to exceed the 1V reference level, this amplifier will pull down on VC and take command of the PWM. As described earlier, VC is the current command voltage, so limiting VC in this manner will also limit output current. The resulting average output current is given by the following equation: IOUT(AVG) 25,000 * 1V RPROG where: RPROG = 24.9k to 100k. The largest recommended PROG pin resistor is 100k. Values of RPROG larger than 100k may latch-off the LTC3114-1 if VOUT is forced to less than 2V by an external load. This is generally not an issue for battery charging applications, but may prevent the charging of very large capacitors. In some general purpose power supply applications, this latch-off behavior may be desirable and in these cases, values of RPROG > 100k are acceptable to use. The gain of 25,000 is generated internal to the LTC31141 and is factory trimmed to provide the best accuracy at 500mA of output current. The accuracy of the programmed output current is best at the high end of the range as the residual internal current sense amplifier offset becomes a smaller percentage of the total current sense signal amplitude with increasing current. The provided electrical specifications define the PROG pin current accuracy over a range of output currents. Selecting the capacitor, CPROG, to put in parallel with RPROG is a trade-off between response time, output current ripple and interaction with the normal output voltage control loop. In general, if speed is not a concern as is the case for most current sourcing applications, then CPROG should be made at least 3 times higher than the voltage error amplifier compensation capacitor, CP1, described 24 in the Compensation section of this data sheet. This will ensure minimal to no interaction when the transition occurs between voltage regulation mode and output current regulation mode. In current sourcing applications, the maximum output compliance voltage of the LTC3114-1 is set by the voltage error amplifier dividers resistors as it is for standard voltage regulation applications. For LED drivIng applications, select the VOUT divider resistors for a clamping level 1V to 2V higher than the expected forward voltage drop of the LED string. The average output current circuitry can also be used to monitor, rather than control the output current. To do this, select an RPROG value that will limit the voltage on the PROG pin to 0.8V or less at the highest output current expected in the application. Connect a 20k resistor and 33nF capacitor from PROG to ground if the function is not going to be used to provide a higher level of protection against inadvertent short-circuit conditions on VOUT. Compensation of the Buck-Boost Converter The LTC3114-1 utilizes average current mode control to regulate the output voltage. Average current mode control has two loops that require frequency compensation, the inner average current loop and the outer voltage loop. The compensation for the inner average current loop is fixed within the LTC3114-1 in order to provide the highest possible bandwidth over the wide operating range of the LTC3114-1. Therefore, the only control loop that requires compensation design is the outer voltage loop. As will be shown, compensation design of the outer loop is similar to the techniques used in well known peak current mode control devices. The LTC3114-1 utilizing average current mode control can be conceptualized in its simplest form as a voltage-controlled current source (VCCS), driving the output load formed primarily by RLOAD and COUT, as shown in Figure6. The error amplifier output (VC), provides the command input to the VCCS. The full-scale range of VC is 0.865V (135mV to 1V). With a full-scale command on VC, the LTC3114-1 buck-boost converter will generate an average 1.7A of inductor current (typical) from the converterfor a For more information www.analog.com Rev. D LTC3114-1 APPLICATIONS INFORMATION + - VOUT VOLTAGE ERROR AMP gm + - VOLTAGE CONTROLLED CURRENT SOURCE FB 1V RTOP 1.7M RBOT 100k COUT 22F RCOSER 0.01 RLOAD 18 1V GND RZ CP1 2 * RLOAD * COUT CP2 31141 F06 Figure6. Simplified Representation of Average Current Mode Control Loop transconductance gain of 1.97A/V. Similar to peak current mode control, the inner average current mode control loop effectively turns the inductor into a current source over the frequency range of interest, resulting in a frequency response from the power stage that exhibits a single pole (-20dB/decade) roll off. The output capacitor (COUT) and load resistance (RLOAD) form the normally dominant low frequency pole and the effective series resistance of the output capacitor and its capacitance form a zero, usually at a high enough frequency to be ignored. A potentially troublesome right half plane zero (RHPZ) is also encountered if the LTC3114-1 is operated in boost mode. The RHPZ causes an increase in gain, like a zero, but a decrease in phase, like a pole. This will ultimately limit the maximum converter bandwidth that can be achieved with the LTC3114-1. The RHPZ is not present when operating in buck mode. The overall open loop gain at DC is the product of the following terms: Voltage Error Amp Gain: gm * RO = 120s * 3.6M = 432V/V (not adjustable) Voltage Divider Gain: Output Load Pole(P1): 1 VC gm = 1.7A/0.865V The frequency dependent terms that affect the loop gain include: VFB 1V = VOUT VOUT (determined by the application, VFB is the reference voltage for the voltage error amplifier) Current Loop Transconductance: (application dependent) Error Amplifier Compensation (2 Poles and 1 Zero): These are the design variables available Right Half Plane Zero (RHPZ): boost mode only (determined by maximum load, VIN, VOUT and inductor) Current Amplifier Compensation Components (Fixed Internal to the LTC3114-1) The internal current amplifier and inner current loop have a much higher bandwidth than the overall loop, however, unlike an ideal VCCS with a flat gain versus frequency characteristic, the inner loop exhibits gain peaking in the range of approximately 2kHz to 20kHz that is an artifact of the fixed current amplifier compensation. This gain peaking has the effect of pushing out the overall loop crossover frequency, while providing some phase margin boost as well. As long as there is sufficient margin between the loop crossover frequency and the worst-case RHPZ frequency, then stable operation over all conditions is relatively easy to achieve. The design parameters for compensation design will focus on the series resistor and capacitors connected from VC to ground (RZ, CP1 and CP2). The general goal is to provide a phase boost using the compensation network zero in order to maximize the bandwidth and phase margin of the converter. Being a buck-boost converter, the target loop crossover frequency for the compensation design will be dictated by the highest boost ratio and load current that is expected as this will result in the lowest RHPZ frequency. An illustrative example is provided next that will derive the compensation components for a typical LTC3114-1 application. Compensation Example 1.7A GC = = 1.97A/V (not adjustable) 0.865V Load Resistance (RLOAD) (determined by the application) This section will demonstrate how to derive and select the compensation components for a typical LTC3114-1 application. Designing compensation for other applications For more information www.analog.com Rev. D 25 LTC3114-1 APPLICATIONS INFORMATION is simply a matter of substituting different values in the equations provided and reviewing the Bode plots, making minor adjustments as needed. Since the compensation design procedure uses a simplified model of the LTC3114-1, the results from the following compensation design should always be verified with time domain step load response tests to validate the effectiveness of the compensation design. It is assumed that the value and type of output capacitor will be selected based on the guidelines provided elsewhere in this data sheet. Particular attention needs to be paid to the voltage bias effect on ceramic capacitors typically used for output bypassing. Similarly, it is assumed that the inductor value and current rating has been selected as well based on the application requirements. VIN = 9V to 36V VOUT = 12V Maximum IOUT (boost mode) = 700mA, RLOAD (min) = 12V/0.7A = 17.1 Maximum IOUT (buck mode) = 1A, RLOAD (min) = 12 COUT = 44F L = 10H Since this application includes boost mode operation, the first step is to calculate the worst-case RHPZ frequency as this will dictate the maximum loop bandwidth for the converter: VIN2 * RLOAD (Hz) VOUT2 * 2 * L substituting the values mentioned earlier yields: RHPZ(f) = 9V 2 * 17.1 12V 2 * 2 * 10H = 153.1kHz In order to account for internal IC component variations, it is good practice to set the converter bandwidth or crossover frequency at least three times lower than the RHPZ frequency to avoid excessive phase loss from the RHPZ when operating in boost mode. In some instances such 26 The system poles and zeros are as follows: 1 ; Output Load Pole (P1) = 2 * R LOAD * COUT buck mode, where RLOAD = output resistance. In boost mode this equation is slightly different: 2 (2 * RLOAD * COUT ) , but with the reduced output current capability in boost (higher RLOAD), the load pole location is about the same. Example Application Details: RHPZ(f) = as higher output voltage applications, an even greater separation between the loop crossover frequency and the RHPZ frequency may be necessary. In this example design, we'll plan to achieve a loop bandwidth (fCC) of 29kHz or approximately one-fifth the RHPZ frequency. 1 Error Amp Pole (P2) = 2 * R * C ; ( EA C) this pole is very close to DC, REA = error amp output resistance, which is approximately 3.6M. It has no impact on the compensation design, but is included here for completeness. 1 ; (2 * RZ * CP1) RZ and CP1 are the error amp compensation components that will be selected. Compensation Zero (Z1) = Ignoring very high frequency output capacitor ESR zero and secondary high frequency error amp pole, the system has two poles and one zero. The error amp pole (P2) is always near DC and we have little influence on it. The output load pole (P1) will move depending on buck-boost converter load resistance. The highest frequency for P1, the output load pole, is at maximum load current (minimum RLOAD). If we design the error amp zero (Z1) frequency so that it coincides with P1(max), then we will get the maximum phase benefit from the compensation network at full load and enough phase boost at lighter loads for stable operation and a single pole response where the loop crosses zero dB. Rev. D For more information www.analog.com LTC3114-1 APPLICATIONS INFORMATION Assuming the error amp zero is designed as just described, at frequencies above P2 (and Z1), the closed-loop gain of our system simplifies to: GCL = GCS * RLOAD * gm * RZ VOUT GCS is the inner current loop closed-loop transconductance = 1.97A/V RLOAD is the minimum load resistance in ohms gm is the transconductance of the error amplifier, 120S RZ is the compensation zero setting resistor (one of our design variables) VOUT is the output voltage Our desired closed-loop frequency (fCC) defined earlier is 29kHz. Assuming that we have a single pole response in our system, we can express the ratio of the closed-loop crossover frequency to fP1 in the buck mode of operation as follows: fCC GCS * RLOAD * gm * Rz = fP1 VO If the inner current loop were an ideal VCCS, then the previously derived compensation would be sufficient to stabilize the converter. However, the inner current loop utilizes an operational amplifier with an integral compensation network, which contributes an additional zero and pole in the power stage response, the gain peaking, as described previously. The effect of the additional zero/pole pair pushes out fCC, our crossover frequency, beyond what was predicted by the previous calculations. A simplified approach to calculating our compensation components then is to re-use the previous equations but scale fCC, the cross over frequency, by a scaling factor (), which will account for the gain boost present in the system: fCC = fCC * ( ), where = 0.42 3 So, in our example, this results in: We can now calculate RZ by rearranging the previous equation: RZ = RZ = 407k, CP1 = 1.3nF, but please continue reading as this is not the final answer. where: Quickly substituting our values in the above equations yields: fCC = 29kHz * ( 0.42) = 4.06kHz 3 Using the new value of fCC in the previous equations for RZ and CC yields: fCC * VOUT * 2 * COUT GCS * gm 4.06kHz * 12V * 2 * 44F 1.97A 120A * V V RZ = 56.9k, use 56.2k RZ = It's important to note that the value of RZ is proportional to the overall crossover frequency, fCC. If we later want to adjust fCC lower, for example, RZ can be lowered in value and CP1 increased proportionally to keep the compensation zero at the same frequency. As mentioned previously, we will place the zero at frequency P1, yielding: R *C 1 CP1 = or more simply, LOAD OUT 2 * RZ * fP1 RZ where Rl is the minimum load resistance in buck mode, 12 in this example. 12 * 44F 56.2k CP1 = 9.4nF, use 10nF CP1 = CP2 is usually chosen to be a small value around 10pF as it is meant to filter out high frequency switching frequency related components. Keep in mind that this analysis assumes that the zero provided by the output capacitor and its ESR is at a frequency much higher than fCC. Rev. D For more information www.analog.com 27 LTC3114-1 TYPICAL APPLICATIONS 9V to 36V VIN to 12V VOUT Regulator 10H 68nF VIN 9V TO 36V SW1 SW2 BST2 BST1 LTC3114-1 VIN PVOUT 10F 33nF PVIN RUN PROG MODE 20k GND LDO PLDO 68nF FB VC PGND 2M 4.7F 10nF 10pF VOUT 12V AT 1A, VIN > 12V 44F 12V AT 0.7A, VIN > 9V 182k 56.2k 31141 TA02a INDUCTOR: WURTH 744 065 100 Efficiency vs Input Voltage 95 Load Step Response ILOAD = 350mA 94 EFFICIENCY (%) 93 LOAD CURRENT 500mA/DIV 92 91 90 VOUT 200mV/DIV 89 88 VIN = 15V 100mA to 700mA 87 86 85 8 12 16 20 24 28 32 INPUT VOLTAGE (V) 36 1ms/DIV 31141 TA02c 40 31141 TA02b 28 Rev. D For more information www.analog.com LTC3114-1 TYPICAL APPLICATIONS 6V to 40V VIN to 24V VOUT Regulator 15H 68nF VIN 6V TO 40V SW1 SW2 BST1 BST2 LTC3114-1 VIN PVOUT 10F 33nF PVIN RUN PROG MODE 20k GND LDO PLDO 68nF 2M 4.7F FB VC PGND 10nF 10pF VOUT 24V AT 1A, VIN > 24V 22F 24V AT 0.2A, VIN = 6V 86.6k 39.2k 31141 TA03a INDUCTOR: WURTH 744 066 150 Efficiency vs Load Current 95 90 12V VIN Synchronous Boost Operation with Inrush Current Limiting at Start-Up and Output Disconnect in Shutdown VIN = 12V 85 RUN PIN 2V/DIV EFFICIENCY (%) 80 75 INPUT CURRENT 1A/DIV 70 65 VOUT 10V/DIV 60 55 50 10ms/DIV 31141 TA03c 45 40 0.1 1 10 100 LOAD CURRENT (mA) 1000 31141 TA03b Rev. D For more information www.analog.com 29 LTC3114-1 TYPICAL APPLICATIONS Constant Current/Constant Voltage Lead-Acid Battery Charger VBATT FLOAT LEVEL -30C 14.5V 0C 14.03V 25C 13.8V 50C 13.48V 6.8H 68nF VIN 2.7V TO 40V 10F 33nF 24.9k 68nF SW1 SW2 BST2 BST1 LTC3114-1 VIN PVOUT PVIN RUN D1 LDO PLDO NTC 68k FB VC PROG MODE GND + 44F 2M 4.7F 6-CELL LEAD-ACID BATTERY 220k 10nF PGND 1A CONSTANT CHARGING CURRENT WHEN BELOW FLOAT LEVEL 31141 TA04a 56.2k TEMPERATURE COMPENSATION 164k NTC: VISHAY NTCS0603E3683 HT 68k NOMINAL AT 25C INDUCTOR: COILCRAFT MSS1048-682NL D1: ON SEMI MBRS260T3G Constant Current High Brightness LED Driver 15H 68nF VIN 9V TO 40V 500mA: R1 = 49.9k 350mA: R1 = 71.5k ADJUST R1 FOR DIMMING SW1 SW2 BST2 BST1 LTC3114-1 VIN PVOUT 10F PVIN RUN LDO PLDO FB VC PROG MODE R1 71.5k GND 3.3nF PGND 68nF 500mA CONSTANT CURRENT, VIN > 11V 350mA CONSTANT CURRENT, VIN > 9V CONSTANT CURRENT DOWN TO 2V D1 4.7F 0.47F 44F 1M 71.5k 31.6k 31141 TA05a VOLTAGE DIVIDER LIMITS VOUT TO 15V IN CASE OF OPEN LED INDUCTOR: WURTH 744 066 150 D1: ON SEMI MBRS260T3G Efficiency vs Input Voltage, 350mA Drive Current 95 94 EFFICIENCY (%) 93 92 91 90 89 88 87 86 85 8 12 16 20 24 28 32 INPUT VOLTAGE (V) 36 40 31141 TA05b 30 Rev. D For more information www.analog.com LTC3114-1 PACKAGE DESCRIPTION DHC Package 16-Lead Plastic DFN (5mm x 3mm) (Reference LTC DWG # 05-08-1706 Rev O) 0.65 0.05 3.50 0.05 1.65 0.05 2.20 0.05 (2 SIDES) PACKAGE OUTLINE 0.25 0.05 0.50 BSC 4.40 0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 5.00 0.10 (2 SIDES) R = 0.20 TYP 3.00 0.10 (2 SIDES) 9 R = 0.115 TYP 0.40 0.10 16 1.65 0.10 (2 SIDES) PIN 1 TOP MARK (SEE NOTE 6) PIN 1 NOTCH 0.200 REF 0.75 0.05 0.00 - 0.05 8 1 0.25 0.05 0.50 BSC (DHC16) DFN 1103 4.40 0.10 (2 SIDES) BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WJED-1) IN JEDEC PACKAGE OUTLINE MO-229 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE Rev. D For more information www.analog.com 31 LTC3114-1 PACKAGE DESCRIPTION FE Package 16-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1663 Rev L) Exposed Pad Variation BB DETAIL A 4.70 (.185) 3.70 (.146) 0.56 (.022) REF 4.90 - 5.10* (.193 - .201) 3.70 0.15 (.146 .006) NOTE 5 16 1514 13 12 1110 0.53 (.021) REF DETAIL A IS THE PART OF THE LEAD FRAME FEATURE FOR REFERENCE ONLY NO MEASUREMENT PURPOSE 9 NOTE 5 6.60 0.10 2.94 3.05 (.116) (.120) 4.50 0.10 DETAIL A SEE NOTE 4 2.94 0.15 6.40 0.15 (.116 .006) (.252 .006) 1.05 0.10 0.65 BSC 0.45 0.05 1 2 3 4 5 6 7 8 RECOMMENDED SOLDER PAD LAYOUT 4.30 - 4.50* (.169 - .177) 0.09 - 0.20 (.0035 - .0079) 0.25 REF 0.50 - 0.75 (.020 - .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 3. DRAWING NOT TO SCALE 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT 32 1.10 (.0433) MAX 0 - 8 0.65 (.0256) BSC 0.195 - 0.30 (.0077 - .0118) TYP 0.05 - 0.15 (.002 - .006) FE16 (BB) TSSOP REV L 1216 5. BOTTOM EXPOSED PADDLE MAY HAVE METAL PROTRUSION IN THIS AREA. THIS REGION MUST BE FREE OF ANY EXPOSED TRACES OR VIAS ON PCB LAYOUT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE Rev. D For more information www.analog.com LTC3114-1 REVISION HISTORY REV DATE DESCRIPTION PAGE NUMBER A 11/14 Corrected Part Marking Table for TSSOP Package Option. 2 B 03/16 Clarified Min VIN on Electrical Characteristics. 3 Clarified FB (Pin 7) description, BST2 (Pin 12) and BST1 (Pin 13) description. 9 Added High Transient Input Voltage Applications section. 17 Clarified Average Output Current Limit Programming section. 23 Added optional diode to Typical Applications. 17-30 Added LTC3118 to Related Parts. 34 1, 3 C 07/19 Add AEC-Q100 Qualification and Orderable Part Numbers D 05/20 Added patent number to end of paragraph description. 1 Added #W_FE temp grades to part list (I, E). 3 Schottky diode recommendation to PVOUT. 10 Striked out "High transient Input Voltage Applications". 18 Removed D1 from schematic. 28 Removed D1 part number description from schematic. 28 Removed D1 from schematic. 29 Removed D1 part number description from schematic. 29 Removed D2 from schematics. 30 Removed D2 part number description from schematics. 30 Removed D1 from schematic. 34 Removed D1 part number description from schematic. 34 Rev. D Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license For is granted implication or otherwise under any patent or patent rights of Analog Devices. moreby information www.analog.com 33 LTC3114-1 TYPICAL APPLICATION Wide VIN Range 5V, 1A Regulator with Bootstrapped LDO and Custom UVLO Threshold 6.8H 68nF VIN 3.75V TO 40V ON: VIN > 4V OFF: VIN < 3.75V 10F SW1 SW2 BST1 BST2 LTC3114-1 VIN PVOUT 1.4M PVIN RUN LDO PLDO 68nF 4.7F IMPROVES EFFICIENCY AT HIGH VIN BAT54 604k 10nF 2M FB VC PROG MODE 20k VOUT 5V AT 1A 30F VIN > 5V GND PGND 499k 4700pF 27.4k 10pF 31141 TA06 INDUCTOR: WURTH 744 065 0068 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC3534 7V, 500mA (IOUT), 1MHz Synchronous Buck-Boost DC/DC Converter 94% Efficiency, VIN: 2.4V to 7V, VOUT: 1.8V to 7V, IQ = 25A, ISD < 1A, DFN and GN Packages LTC3112 2.5A (IOUT), Synchronous Buck-Boost DC/DC Converter VIN: 2.7V to 15V, VOUT: 2.5V to 14V, IQ = 40A, ISD < 1A, DFN and TSSOP Packages LTC3115-1 40V, 2A Synchronous Buck-Boost DC/DC Converter VIN, VOUT: 2.7V to 40V, IQ = 30A, ISD = 3A, DFN and TSSOP Packages LTC3785 10A (IOUT), High Efficiency, 1MHz Synchronous, No RSENSETM VIN: 2.7V to 10V, VOUT: 2.7V to 10V, IQ = 86A, ISD < 15A, QFN Package Buck-Boost DC/DC Controller LTC3789 Buck-Boost DC/DC Controller 96% Efficiency, VIN: 4.5V to 38V, VOUT: 0.8V to 38V, 4mm x 5mm QFN and SSOP Packages LTM(R)4605 4.5V to 20V, 10A Buck-Boost Module(R) Regulator High Power Buck-Boost Module Regulator LTC3129 15.75V, 200mA Buck-Boost DC/DC Converter with 1.3A IQ VIN: 2.42V to 15.75V, VOUT: 1.4V to 15V, IQ = 1.3A, ISD = 10nA, DFN and MS Packages LTC3129-1 15.75V, 200mA Buck-Boost DC/DC Converter with 1.3A IQ and Programmable Output Voltages VIN: 2.42V to 15.75V, VOUT: Pin Programmable 2.5V to 15V, IQ = 1.3A, ISD = 10nA, DFN and MS Packages LTC3118 10V, 2A Synchronous Buck-Boost DC/DC Converter with Low Loss Dual Input PowerPathTM VIN: 2.2V to 10V, VOUT: 2.0V to 16V, IQ = 50A, ISD<1A, 4mmx5mm QFN and TSSOP Packages 34 Rev. D 05/20 www.analog.com For more information www.analog.com ANALOG DEVICES, INC. 2020