19-0117; Rev 1; 11/94 SMA AXI/AV High-Speed, CMOS, Quad, General Description Maxim's H!-201HS is a monolithic, CMOS, quad, single- pole-single-throw (SPST), high-speed analog switch featuring fast switching times (toFF, toN s 5Ons) and tow on resistance (50Q max). It is pin compatible with the industry-standard DG201A. Maxim's new high-voltage silicon-gate technology in- creases the maximum supply-voltage rating to 44V. This improvement allows continuous operation with 20V sup- plies, which is not permitted with the original manufacturer's devices. Maxim's HI-201HS operates from dual supplies ranging from +5V to +20V, or from single supplies from +12V to +20V. Logic levels are TTL-/CMOS-compatible with single or dual supplies within these ranges. Maxims HI-201HS is guaranteed not to latch up if power supplies are disconnected while the analog-switch inputs are present, provided the switch continuous-current ratings are not exceeded. When powered up, the HI-201HS will switch analog signals up to the power-supply rails. Applications Automatic Test Equipment (ATE) Heads-Up Displays Communication Systems Sample-and-Hold Circuits Military Integrator Reset Circuits Functional Diagram SPST Analog Switch Features @ Guaranteed Single-Supply Operation: +12V to +20V @ Guaranteed Dual Supplies: +5V to +20V @ Fast Switching Times: - ton = 30ns torr = 40ns @ Low, 50Q Max On Resistance @ TTL-/CMOS-Compatible @ 44V Max Supply Rating Ordering Information V+ INPUT PAIDAM SOURCE HI-201HS GATEP GATEN ah SWITCH Wee rat LEVEL SHIFTER AND DRIVER rT DRAIN OUTPUT PART TEMP. RANGE PIN-PACKAGE HI3-0201HS-5 OC to +70C 16 Plastic DIP Hi6-0201HS-5 0C to +70C 16 Narrow SO HI1-0201HS-5 OC to +70C 16 CERDIP HI0-0201HS-6 0C to +70C Dice* HI3-0201HS-9 -40C to +85C 16 Plastic DIP HI6-0201HS-9 -40C to +85C 16 Narrow SO H11-0201HS-9 -40C to +85C 16 CERDIP HI4-0201HS-2 -55C to +125C 16 CERDIP H14-0201HS-8 -55C to +125C 20 LCC** * Contact factory for dice specifications. ** Contact factory for availability. Pin Configurations TOP VIEW Al ait <Hil n oumt [2 ry (sl outa m [aI 14 IN2 Ly Aone S vs eno [5] 12] NC. ina [| a] ns aura rH. fn ours wf phe] u SWIT! DIP/SO oN Pin Configurations continued on last page. 1 OFF MA AXIAA Maxim integrated Products 1 SHtOd-IHHI-201HS High-Speed, CMOS, Quad, SPST Analog Switch ABSOLUTE MAXIMUM RATINGS Voltage Referenced to V- VE ee eee ee eee tee ee ee ees 44V GND 20. eee 25V Digital Inputs Vs, Vb (Note 1)... (V-- 4V) to (V+ + 4V) or 30mA (whichever occurs first) Current (any terminal, exceptSorD) ..............- 30mA Continuous Current, SorD 2.0... eee 20mA Peak Current, S or D (pulsed at 1ms, 10% duty cycle max).............. 40mA Continuous Power Dissipation (Ta = +70C, Note 2) 16-Pin DIP (derate 10.53mW/C above +70C)...... 842mW 16-Pin Wide SO (derate 9.52mW/C above +70C) ... 762mW 16-Pin CERDIP (derate 10.00mW/"C above +70C) .. 800mMW 20-Pin LCC (derate 9.09mW/"C above +70C) ...... 727mW Operating Temperature Ranges: HI-O201HS-5/-6 . 2. ee eeeee OC to +70C HI-O201HS-9 eee -40C to +85C HI-O201HS-2/-8 2.0... cee ees -55C to +125C Storage Temperature Range .............. -65C to +150C Lead Temperature (soldering, 10sec) .............. +300C Note 1: Signals on Sx, Dx, or INx exceeding V+ or V- are clamped by internal diodes. Limit forward current to maximum current ratings. Note 2: All leads soldered or welded to PC board. Stresses beyond those listed under Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation oi the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (V+ = 15V, V- = -15V, GND = OV, Ta = +25C, unless otherwise noted.) HI-201HS-2/-8 HI-201HS-5/-6/-9 PARAMETER SYMBOL CONDITIONS MIN TYP MAX! MIN TYP max | UNITS (Note 3) (Note 4) (Note 3) (Note 4) | SWITCH Analog-Signal Range | VANALOG -15 15 -15 15 Vv Drain-Source On _ _ _ Resistance (Note 5) "oS (on) | Vo =210V, Vin = 0.8V, Is = IMA 30 50 30 50 Q Source-Off Leakage Vs = 14V,Vo=-14V/; -1 0.01 1 -1 40.01 1 i VIN = 3.0V nA Current Sto) | NIN Vs=-14V,Vp=14v] -1 4002 1 | -1 2002. 1 Drain-Off Leakage , Vin = 30V Vo = 14V,Vg=-14V] -1 +0.01 1 -1 +0.01 1 A Current P (of IN= 3.0 Vo =-14V,Vs=14V | -1 40.02 1 -1 40.02 1 " Drain-On Leakage - ID (on) Vb = -14V, Vin = 0.8V -1 -+0.10 1 -1 0.10 1 nA Current (Note 6) Vp = 14V, Vin = 0.8V 140.15 1 | -1 #016 1 LOGIC INPUT input Current with tiny (WINE 3.0V a 0 1 4 0 1 uA Input Voltage High VIN = 15V 4 1 4 0 1 Input Current with _ . . Input Voltage Low HNL VIN = 0.8V 1 0) 1 1 0 1 pA MAAXIANHigh-Speed, CMOS, Quad, ELECTRICAL CHARACTERISTICS (continued) (V+ = 15V, V- = -15V, GND = OV, Ta = +25C, unless otherwise noted.) SPST Analog Switch HI-201HS-2/-8 HI-201HS-5/-6/-9 PARAMETER SYMBOL CONDITIONS MIN TYP MAX! MIN TYP MAX |UNITS (Note 3) (Note 4) (Note 3) (Note 4) DYNAMIC Turn-On Time ton Figure 6 30 50 30 50 ns . toff . 40 50 40 50 Turn-Off Time Figure 6 ns toff2 150 150 Output Settling Time 180 180 ns Charge Injection Q CL = 1000pF, VGeEN = OV, RGEN = 0Q 10 10 pc Source-Off Capacitance Cs (off) | Vs = OV, VIN = 5V f = 140kHz 10 10 pF Drain-Off Capacitance | Cp (off) | Vs = OV, VIN=5V f = 140kHz 10 10 pF Channel-On CD (on)* Ve= - _4 Capacitance C8 (on) Vp = Vs = OV, VIN= OV | f = 140kHz 30 30 pF Off Isolation VIN = 3VRMS, ZL = 1kQ, f = 100kHz 72 72 dB Crosstalk _ _ (Channel-to-Channel) Vs = 2.0V, f = 100kHz 90 90 dB SUPPLY positive Supply 1+ | Allchannels on or off 30 38 65/ 30 38 65| mA Negative Supply Current I- 1.0 1.0 mA Power-Supply Range for Continuous Vop (Note 5) +4.5 +20 | +45 +20 Vv Operation MAXIAA 3 SH+LOd-IHHI-201HS High-Speed, CMOS, Quad, SPST Analog Switch ELECTRICAL CHARACTERISTICS (V+ = 15V, V- = -15V, GND = OV, Ta = TMIN to TMAX, unless otherwise noted.) HI-201HS-2/-8 HI-201HS-5/-6/-9 PARAMETER SYMBOL CONDITIONS MIN TYP MAX! MIN TYP MAX | UNITS (Note 3) (Note 4) (Note 3) (Note 4) SWITCH Analog-Signal Range | VANALOG -15 15 -15 15 Rea eienco Note 5) | "28 (on) | Vo = 410V, Vin = 0.8V, Is = 1mA 75 _ m1 a 7 Vs = 14V, Vp = -14 -100 100 -50 50 Curent n IS (off) | VIN=3.0V ve = -14V, Vb = av 100 100 | -50 50 | ine! Vp = 14V, Vg = -14V | -100 100 -50 50 Curent age Dio) | VIN=3.0V Yb =-14V, 7" = 14v | -100 100 | -50 50 | Drain-On Leakge I> com Vp = -14V, Vin = 0.8V -100 100 | -50 so | urrent (Note 6) Vo = 14V, Vin = 0.8V -100 100 | -50 50 LOGIC INPUT Input Current with tN VIN = 3.0V 71.0 1.0 | -1.0 1.0 WA Input Voltage High Vin = 15V -1.0 1.0] -1.0 4.0 net Voltage Lew Int | Vin=0.8V 1.0 1.0 | -1.0 1.0 | pA DYNAMIC Turn-On Time ton See Figure 6 75 75 ns Turn-Off Time toff See Figure 6 | 75 75 ns SUPPLY Positive Supply Current I+ Alf channels on or off 10 10 mA Negative Supply Current I- All channels on or off 6 6 mA Note 3: The algebraic convention where the most negative value is a minimum and the most positive a maximum is used in this data sheet. Note 4: Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing. Note 5: Electrical characteristics, such as on resistance, will change when power supplies other than+15V are used. Note 6: ID(on) is leakage from driver into on switch. MAAXLANHigh-Speed, CMOS, Quad, Protecting Against Fault Conditions Fault conditions occur when power supplies are turned off and input signals are still present, or when overvol- tages occur at the inputs during normal operation. In either case, source-to-body diodes can be forward biased and conduct current from the signal source. If this current must be kept at low (1A) levels, we recommend adding external protection diodes (Figure 1). SPST Analog Switch To provide protection for overvoltages up to 20V above the supplies, place a 1N4001 or 1N914 type diode in series with the positive and negative supplies, as shown in Figure 1. Adding these diodes will reduce the analog- signal range to 1V below the positive supply and 1V above the negative supply. 1mA G] 6] Vo Ch ) [2] 15] RON=sma | Ve > ingoor [3] 14] IN4001 Vv 4{4] ama fis] ig +180 [5] 2] OUT IN [6] 13] | MAAXLAR kd HO] AN HI-207HS [3] [9] Figure 1. Protection Against Fault Conditions Figure 2. On Resistance IN * ouT MAAXLAA HI-201HS \S(OFF) 'D(OFF) IN OuT : SADDAM e HI-201HS +4v +14y \D(ON) L = Hv 7 = Figure 3. On Leakage Current MAXLAN Figure 4. Off Leakage Current SH+4Od-IHHigh-Speed, CMOS, Quad, SPST Analog Switch i) Pin Configurations (continued) TOP VIEW re LOGIC "0" = SWITCH ON pigita, YAH =3 WN INPUT / ~ 50% 50% z= . 2 8 S = 8 5 Val =0V ox z226 r ya - & Z t ON 90% IN1 4 1a IN2 SWITCH OV - OUTPUT 's MAXUM 17 Vs NC. 6 HI-201HS 16 NC. GND 7 15 NC. IN4 8 14 IN3 SWITCHING TEST CIRCUIT (ton1; torFt1, toFF2) V4 =+15V 13] eoeorese Fagoe?e SWITCH SWITCH 3 = 3 INPUT 3 2 OUTPUT VIN= H10V of Vo AL Lec ! CL i 350F MAAXMLAA = LOGIC HI-201HS INPUT o | = = RL GND v-e-tgy YO" C_ INCLUDES Crixture + CPROBE PIN NUMBERS ARE FOR DIP PACKAGE. Figure 6. Switching-Time Test Circuit \ MAXIMA 6High-Speed, CMOS, Quad, SPST Analog Switch Package Information oim |__INCHES MILLIMETERS . , MIN | MAX | MIN | MAX D }~- 1 | A - 0.200 - 5.08 . 1 Ai | 0.015 | 0.38 - 4, A , A3 a2 | 0.125 | 0.175 | 3.18 | 4.45 a A2 i A3 | 0.055 | 0.080 | 1.40 | 2.03 im : 8 | 0.016 | 0.022 | 0.41 | 0.56 i 1 B1 | 0.045 | 0.065-| 1.14 | 1.65 ' \ c | 0.008 | 0.012 | 0.20 | 0.30 Load R sage i Di | 0.005 | 0.080 | 0.13 | 2.03 Y Settle O 15 " E | 0.300 | 0.325 | 7.62 | 8.26 co 1 | 0.240 | 0.310 | 610 | 7.87 e B1 <_-eA> e_| 0.100 - 2.54 = B Tea | 0.300 | - 7.62 = eB_ eB | |o400[ - 10.16 | D1 L | o.415 | 0.150 | 292 | 3.81 mao /earar . INCHES _ [MILLIMETERS Plastic DIP DIM pins| iN MAX T MIN | MAX PLASTIC D | 8 10.348 {0.300 | 6.64 | 9.91 DUAL-IN-LINE D | 14 [0.735 | 0.765 | 18.67 | 19.43 D | 16 {0.745 | 0.765 | 18.92 | 19.43 PACKAGE D | 18 [0.885 | 0.915 | 22.48 | 23.24 (0.300 in.) D | 20 11.015 | 1.045 | 25.78 | 26.54 D | 24 [1.14 | 1.265 [28.96 | 32.13 pina |___INCHES MILLIMETERS MIN | MAX | MIN | MAX A | 0.053 | 0.069 | 1.95 | 1.75 D_r Ai | 0.004 | 0.010 | 0.10 | 0.25 iy ae B | 0.014 | 0.019 | 0.35 | 0.49 ,A t-o ors c | 0.007 | 0.010 | 019 | 0.25 )u TL L LL E | 0.150 | 0.157 | 3.80 | 4.00 iS 0.101mm + 4 e 0.050 1.27 lel elle, H | 0.228 | 0.244 | 5.80 | 6.20 B c L~ i | oo16 | 0.050 | 040 [ 1.27 9/9/99 INCHES [MILLIMETERS Pe SO DIM PINS in| MAX |_MIN | MAX SMALL OUTLINE 8 | 0.189 [0.197 | 4.80 | 5.00 4 H PACKAGE 14 | 0.937 [0.344 | 6.55 | 8.75 . 16 | 0.386 |0.394 | 9.80 | 10.00 (0.150 in.) noua MAAXILM 7 SHlLOc-IHHI-201HS High-Speed, CMOS, Quad, SPST Analog Switch Package Information (continued) INCHES MILLIMETERS DIM ain | MAX [MIN | MAX + E1 A = 0.200 = 5.08 E B | 0.014 | 0.023 | 0.36 | 0.58 A | . . Bi | 0.038 | 0.065 | 0.97 | 1.65 -_ p__+| TI C | 0.008 | 0.015] 020 | 0.38 E | 0.220 | 0310 | 559 | 7.87 | | 1 | 0.290 | 0.320 | 7.37 | 8.13 0.100 2.54 ! ous ft L_| 0.125 | 0.200 | 3.18 | 5.08 esl L1 | 0.150 - 3.81 = i L Ce Qa [ 0.015 | 0.070 | 0.38 | 1.78 Ss - 0.098 - 2.49 B 81 | 0.005 - 0.13 - | ~~ st | a s oim [pins INCHES _| MILLIMETERS CERDIP MIN | MAX | MIN | MAX do | sa | - jo405| - [10.29 CERAMIC DUAL-IN-LINE D 14 - 0.785 - 19.94 PACKAGE D{i6!] - |os4o} - |21.34 . D|ia| - joseo}| - [24.38 (0.300 in.) po [20| - |1060| - [26.92 D [24] - [1.280] - {3251 Maxim cannot assure responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 8 Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 1994 Maxim Integrated Products Printed USA MAAXIM. isa registered trademark of Maxim Integrated Products.