TS-S04D168A November, 2004 Preliminary Specification 10Gb/s XFP Optical Transceiver Module SXP3101SV (IR-2/S-64.2b, 10GBASE-ER/EW, 1550nm EML, PIN-PD) Features u 10Gb/s Serial Optical Interface O High quality and reliability optical device and sub-assemblies O 1550nm EML laser for up to 40km operation single mode fiber O u High sensitivity PIN photodiode and TIA XFP MSA Revision 4.0 Compliant O Easy supply management for hot pluggability O Duplex LC Receptacle O XFP Mechanical Interface with color coded bail latch for easy removal (Bail color: Red) O XFI High Speed Electrical Interface O 2-wire interface for management and diagnostic O u Applications Tx_Disable and Rx_LOS functions u SONET(OC-192)/SDH(STM64) line card u 10GE Ethernet switches and routers SONET OC-192/SDH STM-64 u 10GE Core-routers IEEE802.3ae 10 Gigabit Ethernet u 10GE Storage u Other high speed data connections Multi-Protocol O O u monitoring Low Power Consumption O +3.3V, +5.0V Power Supplies O Power consumption less than 3.5W Framer/Mapper or Ethernet MAC or FC Controlller SER DES SXP3101 (XFP) 10Gb/s XFI electrical signal SXP3101 (XFP) 10Gb/s optical signal SER DES Framer/Mapper or Ethernet MAC or FC Controlller 10Gb/s XFI electrical signal Application Block Diagram SXP3101 Series Sumitomo Electric Industries, Ltd. Page 1 TS-S04D168A November, 2004 Preliminary Specification 1. General Description The SXP3101SV is a very compact 10Gb/s optical transceiver module for serial optical communication applications at 10Gb/s. The SXP3101SV converts a 10Gb/s serial electrical data stream to 10Gb/s optical output signal and a 10Gb/s optical input signal to 10Gb/s serial electrical data streams. The high speed 10Gb/s electrical interface is fully compliant with XFI specification. The SXP3101SV is designed for use in a variety of 10Gb/s SONET/SDH equipment including FEC (9.95Gb/s to 10.7Gb/s) as well as Ethernet LAN (10.3Gb/s) and WAN (9.95Gb/s) applications. The high performance cooled 1550nm EML transmitter and high sensitivity PIN receiver provide superior performance for SONET /SDH and Ethernet applications at up to 40km links. The fully XFP compliant form factor provides hot pluggability, easy optical port upgrades and low EMI emission. 2. Functional Description The SXP3101SV contains a duplex LC connector for the optical interface and a 30-pin connector for the electrical interface. Figure 2.1 shows the functional block diagram of SXP3101SV XFP Transceiver. Transmitter Operation The transceiver module receives 10Gb/s electrical data and transmits the data as an optical signal. The transmitter contains a Clock Data Recovery (CDR) circuit that reduces the jitter of received signal and reshapes the electrical signal before the electrical to optical (E-O) conversion. The optical output power is maintained constant by an automatic power control (APC) circuit. The transmitter output can be turned off by TX disable signal, at TX_DIS pin. When TX_DIS is asserted High, the transmitter is turned off. Receiver Operation The received optical signal is converted to serial electrical data signal. The optical receiver contains a CDR circuits that reshapes and retimes an electrical signal before sending out to the XFI channel (i.e. XFP connector and high speed signal traces). The RX_LOS signal indicates insufficient optical power for reliable signal reception at the receiver. Management Interface A 2-wire interface (SCL, SDA) is used for serial ID, digital diagnostics and other control /monitor functions. The address of XFP transceiver is 1010000x. MOD_DESEL signal can be used in order to support multiple XFP modules on the same 2-wire interface bus. SXP3101 Series Sumitomo Electric Industries, Ltd. Page 2 TS-S04D168A November, 2004 Preliminary Specification VCC5 5.0V VCC3 3.3V SXP3101SV EA TOSA EA Driver Signal Conditioner TDP/TDN Optical Output TEC Control P_DOWN /RST TX_DIS Bias Control Circuit INTb I2C Data SDA I2C Clock SCL MOD_NR uC System Tx Power,Tx Bias Rx Power, LOS MOD-DESEL Current Monitor RX_LOS REFCLKP 100ohm REFCLKN Signal Conditioner with LIA RDP/RDN MOD_Abs ROSA with TIA Optical Input Figure 2.1. Functional Block Diagram 3. Package Dimensions Figure 3.1 shows the package dimensions of SXP3101SV. SXP3101SV is designed to be complaint with XFP MSA specification. Package dimensions are specified in section 6.3 of the XFP MSA specification Rev. 4.0. * Bail c o l o r i s R e d . Unit : mm Figure 3.1. Package Dimensions SXP3101 Series Sumitomo Electric Industries, Ltd. Page 3 TS-S04D168A November, 2004 Preliminary Specification 4. 4.1. Pin Assignment and Pin Description XFP Transceiver Electrical Pad Layout Toward Bezel 1 GND 30 GND 2 VEE5 (not in use) 29 TDP 3 Mod_DESEL 28 TDN 4 INTERRUPTb 27 GND 5 TX_DIS 26 GND 6 VCC5 25 REFCLKN 7 GND 24 REFCLKP 8 VCC3 23 GND 9 VCC3 22 VCC2 (not in use) 10 SCL 21 P_DOWN/RST 11 SDA 20 VCC2 (not in use) 12 MOD_ABS 19 GND 13 MOD_NR 18 RDP 14 RX_LOS 17 RDN 15 GND 16 GND Bottom of XFP PCB (as view hrough top of PCB) Top of XFP PCB (Top View) Figure 4.1 XFP Transceiver Electrical Pad Layout 4.2. Host PCB XFP Pinout Toward Bezel 1 GND 2 VEE5 (not in use) 3 Mod_DESEL 4 INTERRUPTb 5 TX_DIS 6 VCC5 7 GND 8 VCC3 9 VCC3 10 SCL 11 SDA 12 MOD_ABS 13 MOD_NR 14 RX_LOS 15 GND 30 TDP 29 TDN 28 GND 27 GND 26 REFCLKP 25 REFCLKN 24 GND 23 VCC2 (not in use) 22 P_DOWN/RST 21 VCC2 (not in use) 20 GND 19 RDP 18 RDN 17 GND 16 GND HOST PCB Top View Figure 4.2 Host PCB XFP Pinout SXP3101 Series Sumitomo Electric Industries, Ltd. Page 4 TS-S04D168A November, 2004 Preliminary Specification 4.3. Pin Descriptions Table 4.3 Pin Description Pin# Name Logic 1 GND LVTTL-I 2 VEE5 3 MOD_DESEL Description Note Module Ground 1 -5.2V Power Supply; not in use 3 Module De-select; When held Low allows module to LVTTL-I respond to 2-wire serial interface Indicates presence of an important condition, which can be read over the 2-wire serial interface. This pin is an 4 INTERRUPTb LVTTL-O 2 open collector output and must be pulled up to host_Vcc on the host board. Transmitter Disable; When asserted High, transmitter 5 TX_DIS LVTTL-I output is turned off. This pin is pulled up to VCC3 in the module 6 VCC5 +5V Power Supply 7 GND Module Ground 8 VCC3 +3.3V Power Supply 9 VCC3 +3.3V Power Supply 10 SCL 1 2-wire serial interface clock. Host shall use a pull-up I/O 2 resistor connected to host_Vcc of +3.3V. 2-wire serial interface data. Host shall use a pull-up 11 SDA I/O 2 resistor connected to host_Vcc of +3.3V. Indicates Module is not present. Host shall pull up this 12 MOD_ABS LVTTL-O pin, and grounded in the module. "High" when the XFP 2 module is absent from a host board. Module not ready; When High, Indicates Module 13 MOD_NR LVTTL-O Operational Fault. This pin is an open collector and 2 must be pulled to host_Vcc on the host board. Receiver Loss of Signal; When high, indicates insufficient optical input power to the module. This pin is an open 14 RX_LOS LVTTL-O 2 collector and must be pulled to host_Vcc on the host board. 15 GND SXP3101 Series Module Ground Sumitomo Electric Industries, Ltd. Page 5 TS-S04D168A November, 2004 Preliminary Specification Pin# Name 16 GND 17 RDN Logic Description Note Module Ground Receiver Inverted Data Output; AC coupled inside the CML-O module. Receiver Non-Inverted Data Output; AC coupled in side 18 RDP CML-O the module. 19 GND Module Ground 1 20 VCC2 +1.8V Power Supply; not in use 3 Power down; When High, module is limited power mode. Low for normal operation. 21 P_DOWN/RST LVTTL-I Reset; The falling edge indicates complete reset of the module. This pin is pulled up to VCC3 in the module. 22 VCC2 +1.8V Power Supply; not in use 3 23 GND Module Ground 1 24 REFCLKP PECL-I Reference clock Non-Inverted Input; not in use 25 REFCLKN PECL-I Reference clock Inverted Input; not in use 26 GND Module Ground 1 27 GND Module Ground 1 28 TDN Transmitter Inverted Data Input; AC coupled in side the CML-I module. Transmitter Inverted Data Input; AC coupled in side the 29 TDP CML-I module. 30 GND Module Ground 1 Note 1: Module ground pins are isolated from the module case and chassis ground within the module. 2: Shall be pulled up with 4.7k to 10k ohm to a voltage between 3.15V and 3.45V on the host board. 3: Not connected internally. SXP3101 Series Sumitomo Electric Industries, Ltd. Page 6 TS-S04D168A November, 2004 Preliminary Specification 5. Absolute Maximum Ratings and Recommended Operating Conditions Table 5.1. Absolute Maximum Ratings Parameter Strage Temperature Relative Humidity (non-condensation) Operating Case Temperature Short-term operating case temperature Supply Voltage Supply Voltage Voltage on LVTTL Input LVTTL Output Current Voltage on Open Collector Output Receiver Input Optical Power Symbol Tst RH Topc Top-short VCC5 VCC3 Vilvttl Iolvttl Voco Mip Min -40 -5 -10 -0.3 -0.5 -0.5 0 Max 85 85 70 75 6.0 3.6 VCC3+0.5 15 6 3 Unit degC % degC degC V V V mA V dBm Note 1 2 3 Note: 1: Ta: -10 to 60degC with 1.5m/s airflow with an additional heat sink. 2: Performance is not guaranteed. The short term temperature range will not occur continuously, but only during a period of maximum 15 days per year of which 4 days maximum continuously. 3: PIN Receiver Table 5.2. Recommended Operating Conditions and Supply Requirements Parameter Operating Case Temperature Relative Humidity (non-condensing) Power Supply Voltage Power Supply Voltage Power Supply Current Power Supply Current Total Power Consumption SXP3101 Series Symbol Topc Rhop VCC5 VCC3 ICC5 ICC3 Pd Min -5 4.75 3.135 - Max 70 85 5.25 3.465 500 750 3.5 Sumitomo Electric Industries, Ltd. Unit degC % V V mA mA W Note Page 7 TS-S04D168A November, 2004 Preliminary Specification 6. Electrical Interface 6.1. High Speed Electrical Interface XFI Application Reference model Figure 6.1.1 shows the high speed electrical interface (XFI) compliance points. XFI electrical interface is specified for each compliance point in Chapter 3 of the XFP MSA specification. C' C XFP Module D ASIC/ SERDES Receiver O/E Transmitter E/O A Capacitors B' B XFP Connector Figure 6.1.1 XFI Application Reference Model XFI Module Transmitter Input Electrical Interface Specification at B' Table 6.1.1 XFI Transmitter Input Electrical Specification at B' Parameter -B' Reference differential Input Impedance Termination Mismatch Input AC Common mode Voltage symbol Differential Input Return Loss SDD11 Comon Mode Input Return Loss Differential to Common Mode Conversion Total Input Non-DDJ Jitter Total Input Jitter Input Jitter for ITU-T 20kHz-80MHz Input Jitter for ITU-T 4MHz-80MHz SCC11 SCD11 TJtnd TJ Gjin1 Gjin2 X1 Y1 Y2 Eye Mask Min Zd dZm Typ 100 Max 5 25 20 8 See 3 3 10 0.41 0.61 150 50 0.305 60 410 Units Note Ohm % mV(RMS) dB dB dB dB UIp-p UIp-p mUIp-p mUIp-p UI mV mV 1 2 3 4 4 5 Note 1: 0.05-0.1 GHz 2: 0.1-5.5GHz 3: 5.5-12GHz, SDD11(dB)=8-20.66Log10(f/5.5), with f in GHz 4: 0.1-15GHz 5: Eye Mask is defined in Figure 6.1.2 SXP3101 Series Sumitomo Electric Industries, Ltd. Page 8 TS-S04D168A November, 2004 Preliminary Specification XFI Module Receiver Output Electrical Interface Specification at C' Table 6.1.2 XFI Receiver Output Electrical Specification at C' Parameter -C' Reference differential Output Impedance Termination Mismatch Output AC Common mode Voltage Output Rise and Fall time (20%-80%) symbol trh, tfh Differential Output Return Loss SDD22 Comon Mode Input Return Loss Determinstic Jitter Total Jitter SCC22 TJtnd TJ X1 X2 Y1 Y2 Eye Mask Min Typ 100 Zd dZm Max Units Note Ohm % mV(RMS) ps dB dB 5 15 24 20 8 See 3 3 0.18 0.34 0.17 0.42 170 425 dB UIp-p UIp-p UI UI mV mV 1 2 3 4 5 Note 1: 0.05-0.1 GHz 2: 0.1-5.5GHz 3: 5.5-12GHz, SDD11(dB)=8-20.66Log10(f/5.5), with f in GHz 4: 0.1-15GHz 5: Eye Mask is defined in Figure 6.1.3 Y2 Y2 Y1 Y1 0 0 -Y1 -Y1 -Y2 -Y2 0 X1 1-X1 1.0 0 X1 X2 1-X2 1-X1 1.0 Figure 6.1.2 Tranmitter Input Eye Mask Figure 6.1.3 Receiver Output Eye Mask SXP3101 Series Sumitomo Electric Industries, Ltd. Page 9 TS-S04D168A November, 2004 Preliminary Specification XFI Reference Clock Specification Note that the reference clock is not needed for SXP3101SV. The differential reference clock signals if used are internally terminated across a 100Ohm resistance as shown in Figure 2.1. 6. CDR Specification Transmitter CDR Table 6.1 Transmitter CDR Specification Parameter Jitter Transfer Bandwidth Jitter Transfer Peaking symbol Min Typ BW Jp1 Jp2 Max 8 0.1 1 Units Note MHz dB dB 1 2 3 Note 1: In order to meet SONET/SDH jitter transfer requirement, de-jitter PLL will be needed on the host board SerDes. 2: Frequency < 120kHz 3: Frequency > 120kHz Receiver CDR Table 6.2 Receiver CDR Specification Parameter Jitter Transfer Bandwidth Jitter Transfer Peaking symbol Min Typ BW Jp1 Jp2 Max 8 0.1 1 Units Note MHz dB dB 1 2 Note 1: Frequency < 120kHz 2: Frequency > 120kHz SXP3101 Series Sumitomo Electric Industries, Ltd. Page 10 TS-S04D168A November, 2004 Preliminary Specification Table 6.3.1 Low Speed Control and Alarm Signals Electrical Interface Parameter symbol Min 0.0 Vcc-0.5 -0.3 2.0 0.0 Vcc-0.5 -0.3 VCC3*0.7 Capacitance for XFP SCL and SDA I/O pin Vol Voh Vil Vih Vol Voh Vil Vih Ci Total bus capacitive load for SCL and SDA Cb XFP Interrupt, Mod_NR, RX_LOS XFP TX_DIS, P_DOWN/RST XFP SCL and SDA Output XFP SCL and SDA Input Typ Max 0.4 Vcc+0.3 0.8 VCC3+0.3 0.4 Vcc+0.3 VCC3*0.3 VCC3+0.5 14 100 400 Units Note 1 2 3 4 1 2 5 6 V V V V pF pF pF 7 8 Note 1: Pull-up resistor must be connected to host_Vcc on the host board. Iol(max)=3mA 2: Pull-up resistor must be connected to host_Vcc on the host board. 3: Pull-up resistor connected to VCC3 within XFP module. Iil(max)= -10A. 4: Pull-up resistor connected to VCC3 within XFP module. Iih(max)= 10A. 5: Pull-up resistor must be connected to host_Vcc on the host board. Iol(max)= -10A. 6: Pull-up resistor must be connected to host_Vcc on the host board. Iol(max)= 10A. 7: at 400KHz, 3.0kohms, at 100kHz 8.0kohms max 8: at 400KHz, 0.8kohms, at 100kHz 2.0kohms max SXP3101 Series Sumitomo Electric Industries, Ltd. Page 11 TS-S04D168A November, 2004 Preliminary Specification 7. Optical Interface Table 7.1 Optical Interface Transmitter Optical Interface Parameter Operating Data Rate Output Center Wavelength Spectral Width SMSR Average Output Power Disabled Power Extinction Ratio Optical Modulation Amplitude (10G Ethernet) Transmitter and dispersion penalty (10G Ethernet) OMA-TDP (10G Ethernet) Eye Mask 1 (SONET/SDH) Eye Mask 2 (10G Ethernet) Generation Jitter 1 (20kHz - 80MHz) Generation Jitter 2 (50kHz - 80MHz) Generation Jitter 3 (4MHz - 80MHz) RIN Receiver Optical Interface Parameter Operating Data Rate Input Center Wavelength Overload Minimum Sensitivity Sensitivity in OMA Stressed Sensitivity in OMA RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis Optical Path Penalty Optical Return Loss Jitter Tolerance Symbol ltc dl SMSR Po Poff ER OMA TDP OMAtdp RIN Min. 9.95 1530 30 -1 8.2 -1.7 Typ. 1550 Max. 10.75 1565 1 2 -30 3.0 -2.1 GR-253-CORE/ITU-T G.691 IEEE802.3ae 0.15 0.10 0.05 -128 Symbol Min. Typ. Max. 9.95 10.75 lrc 1260 1565 Rovl 0.5 Pmin -14 OMAo -14.1 OMAst -11.3 RLOSa -23 -19 RLOSd -18 RLOSh 0.5 3 PN 2 ORL 27 JTL GR-253-CORE/ITU-T G.783 Unit Gb/s nm nm dB dBm dBm dB dBm dB dBm Note 1 2 2 2 3 3 3 2 3 2, 4 2, 4 2, 4 UIp-p UIp-p UIp-p dB/Hz Unit Gb/s nm dBm dBm dBm dBm dBm dBm dB dB dB Note 1 Note 1 : Data rate tolerance IR-2/S-64.2b, 10GBASE-EW : typ.+/-20ppm 10GBASE-ER : typ.+/-100ppm 2: Measured at 9.95328Gbps, Framed PRBS2^31-1, NRZ 3: Measured at 10.3125Gbps, Non-framed PRBS2^31-1, NRZ 4 : When there is no applied jitter on electrical input to the module SXP3101 Series Sumitomo Electric Industries, Ltd. Page 12 2 2 TS-S04D168A November, 2004 Preliminary Specification 8. Electrical and Optical I/O Signal Relationship Table.8.1 Electrical Input Signal vs. Optical Output Signal Input Signal TDP TDN High Low Low High High High Low Low Optical Output Signal ON (High) OFF (Low) OFF (Low) OFF (Low) Table.8.2 TX_DIS vs. Optical Output Power TX_DIS Low (VIL=-0.3 to 0.8V) Optical Output Power Enabled High (VIH =2.0 to VCC3+0.3V) Disabled (<-30dBm) RX_LOS [V] Voh Vol RXLOSa RXLOSd Optical Input Power [dBm] Figure.8.1 Optical Input Power vs. RX_LOS SXP3101 Series Sumitomo Electric Industries, Ltd. Page 13 TS-S04D168A November, 2004 Preliminary Specification 9. User Interface 9.1. XFP Mechanical Interface XFP Mechanical Interface is specified in the Chapter 6 in the XFP MSA specification. XFP Mechanical Components Figure 8.1 shows the XFP transceiver concept and mechanical components. Figure 9.1 XFP Mechanical Interface Concept and Components XFP Host board Mechanical Layout XFP Host Board Layout is specified in the Figure 35 of the XFP MSA specification (Rev. 4.0). Host Board XFP Connector Footprint and Layout Host board XFP connector layout is specified in the Figure 36 of the XFP MSA Specification (Rev. 4.0). XFP Datum Alignment and Be zel Design XFP datum alignment (depth) is specified in the Figure 30 of the XFP MSA specification (Rev. 4.0). The recommended bezel design is specified in the Figure 37 of the XFP MSA specification (Rev. 4.0). XFP Connector and XFP Cage Assembly The XFP 30-contact connector mechanical specification is shown in Figure 39 of the XFP MSA specification (Rev. 4.0) The XFP Cage Assembly mechanical specification is shown in the Figure 41 of the XFP MSA specification (Rev. 4.0). SXP3101 Series Sumitomo Electric Industries, Ltd. Page 14 TS-S04D168A November, 2004 Preliminary Specification 9.2. Management Interface XFP 2-Wire Serial Interface Protocol XFP 2-wire serial interface is specified in the Chapter 4 of the XFP MSA specification. The XFP 2-wire serial interface is used for serial ID, digital diagnostics, and certain control functions. The 2-wire serial interface is mandatory for all XFP modules. The 2-wire serial interface address of the XFP module is 1010000X(A0h). In order to access to multiple modules on the same 2-wire serial bus, the XFP has a MOD_DESEL (module deselect pin). This pin (which is pull high or deselected in the module) must be held low by the host to select of interest and allow communication over 2-wire serial interface. The module must not respond to or accept 2-wire serial bus instructions unless it is selected. XFP Management Interface XFP Managed interface is specified in the Chapter 5 of the XFP MSA specification. Figure 8.2 shows the structure of the memory map. The normal 256 Byte address space is divided into lower and upper blocks of 128 Bytes. The lower block of 128 Byte is always directly available and is used for the diagnostics and control functions that must be accessed repeatedly. Multiple blocks of memories are available in the upper 128 Bytes of the address space. These are individually addressed through a table select Byte which the user enters into a location in the lower address space. The upper address space tables are used for less frequently accessed functions and control space for future standards definition. 0- Digital Diagnostic functions 118 128- 119-122 4 Btyte Password Change 123-126 4 Btyte Password Entry 127 Page Select Byte Entry 128- Reserved for Future Diagnostic Functions 255 XFP MSA Serial ID Data 223 224 255 Table 00h 128- Vendor Specific ID Data Table 01h 128- User EEPROM Data (not protected) 255 128- Vendor Specific Functions 255 Table 02h Reserved 255 Table 03h-7Fh Table 80h-FFh Figure 9.2 2-wire Serial Interface Memory Map SXP3101 Series Sumitomo Electric Industries, Ltd. Page 15 TS-S04D168A November, 2004 Preliminary Specification 9.3. A/D Accuracy and Values Table 9.3.1 A/D Accuracy Data Address Parameter Relative Units Display Note accuracy Signed 2's complement Junction temperature of NA integer degC monitoring IC. Accuracy 96-97 Temperature +/-3degC 98-99 100-101 Reserved Tx Bias 102-103 Tx Power 104-105 Rx Power 106-107 Vcc +/-10% NA +/-2dB@BOL (Note1) +/-1dB (Range: -1 to +2dBm (Note2) +/-2dB@BOL (Note1) +/-1dB (Range: -16 to (Note2) +0.5dBm) +/-3% NA x2A Specified by nominal value x0.1W Average Power x0.1W At specified transmitter wavelength. x100V 3.3V Only Table 9.3.2 A/D Values Byte Bit Name Description 96 All Temperature MSB 97 98-99 100 101 102 103 104 105 106 107 108 109 All All All All All All All All All All All All Temperature LSB Tx Bias MSB Tx Bias LSB Tx Power MSB Tx Power LSB Rx Power MSB Rx Power LSB Vcc MSB Vcc LSB AUX 2 MSB AUX 2 LSB Signed 2's complement integer temperature (-40 to +125degC) based on internal temperature measurement Fractional part of temperature(count/256) Reserved Measured Laser Bias Current in mA. Bias current is full 16 bit value *2A. (Full range of 0 to 131mA) Measured Tx output power in mW. Tx power is full 16 bit value *0.1W. (Full range of -40 to +8.2dBm) Measured Rx input power in mW. Tx power is full 16 bit value *0.1W. (Full range of -40 to +8.2dBm) Internally measured transceiver supply voltage. Vcc is full 16 bit value*100V. (Full range of 0 to +6.55 Volts) TBD Note1. Over specified temperature and voltage Note2. Over specified temperature and voltage range over the life of the product into a fixed measurement system SXP3101 Series Sumitomo Electric Industries, Ltd. Page 16 TS-S04D168A November, 2004 Preliminary Specification 9.4. Address Serial ID Memory Map (Data Field - Page 01h) Size (Bytes) Name 128 1 Identifier 129 1 Ext. Indentifier 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 1 Connector 8 Tranciver 1 1 1 1 1 1 1 1 1 16 Encoding BR-Min BR-Max Length (SMF)-km Length (E-50 m) Length (50 m) Length (62.5 m) Length (Copper) Device Tech Vendor name 1 CDR Support 3 Vendor OUI 16 Vendor PN 2 Vendor rev 2 Wavelength 2 Wavelength Tolerance 1 1 Max Case Temp CC_BASE Hex ASC Base ID Filed 06 90 07 22 00 00 00 00 20 00 00 B0 64 6C 28 00 00 00 00 74 53 S 75 u 6D m 69 i 74 t 6F o 6D m 6F o 45 E 6C l 65 e 63 c 74 t 72 r 69 i 63 c F0 00 00 5F 53 S 58 X 50 P 33 3 31 1 30 0 31 1 53 S 56 V 20 20 20 20 20 20 20 41 to 5A A to Z 20 79 18 0F A0 46 Note2 Description Address XFP module 3.5W Max With CDR LC Connector 10GBASE-ER/EW S-64.2b 64B/66B, SONET Scrambled, NRZ 9.95Gbps 10.75Gbps 40km Variable 1550nm @ RT +/-20nm (Note1) 70degC 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 Size (Bytes) Name Hex ASC Extended ID Field AF 96 Power Supply A8 00 4 16 Description 3.5W 1.5W (Note3) 500mA/800mA (Note4) Vendor SN Year Month 8 Date Code Note6 Day Lot 220 1 Diagnostic Monitoring Type 08 221 1 Enhanced Options 60 222 223 1 1 Aux Monitoring 70 CC_EXT Note7 Vendor Specific ID Fileds No BER Support Average Power Optional Soft TX_Disable Optional Soft P_down +3.3V Support Voltage 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Note1.The guaranteed +/- range of transmitter output wavelength under all normal operating conditions. Note2. Address 191 is check sum of bytes 128 to 190. Note3. Maximum total power dissipation in power down mode Note4. +1.8V/-5.2V is not in use. Note5. Address 196 to 211 Vendor Serial Number Note6. Address 212 to 219 Date code Note7. Address 223 is check sum of bytes 192 to 222. SXP3101 Series Sumitomo Electric Industries, Ltd. Page 17 TS-S04D168A November, 2004 Preliminary Specification Supply filter Host +5.0V 0.1uF Host +3.3V 0.1uF Host +1.8V (not in use) 0.1uF Host -5.2V (not in use) 0.1uF 4.7uH 22uF 4.7uH 22uF 4.7uH 22uF 4.7uH 22uF Vcc5 0.1uF Vcc3 0.1uF Vcc2 XFP Connector 9.5. XFP Module 0.1uF Vee5 0.1uF Figure 9.5 Supply Filter 9.6. Recommended Electrical Interface Figure 9.6 Recommended Electrical Interface SXP3101 Series Sumitomo Electric Industries, Ltd. Page 18 TS-S04D168A November, 2004 Preliminary Specification 10. Qualification Testing SXP3101SV 10Gb/s transceiver is qualified to Sumitomo Electric Industries internal design and manufacturing standards. Telecordia GR-468-CORE reliability test standards, using methods per MIL-STD-883 for mechanical integrity, endurance, moisture, flammability and ESD thresholds, are followed. 11. Laser Safety Information SXP3101SV OC-192 transceiver uses a semiconductor laser system that is classified as Class 1 laser products per the Laser Safety requirements of FDA/CDRH, 21 CFR1040.10 and 1040.11. These products have also been tested and certified as Class 1 laser products per IEC 60825-1 International standards. Caution _______________________________________________________________________________ If this product is used under conditions not recommended in the specification or is used with unauthorized revision, the classification for laser product safety is invalid. Reclassify the product at your responsibility and take appropriate safety measures. _______________________________________________________________________________ 12. Electromagnetic Compatibility (Pending) EMI (Emission) SXP3101SV is designed to meet FCC Class B limits for emissions and noise immunity per CENELEC EN50 081 and 082 specifications. RF Immunity SXP3101SV has an immunity to operate when tested in accordance with IEC 61000-4-3 (80- 1000MHz, Test Level 3) and GR-1089. Electrostatic Discharge (ESD) Immunity SXP3101SV has an immunity against direct and indirect ESD when tested accordance with IEC 61000-4-2. SXP3101 Series Sumitomo Electric Industries, Ltd. Page 19 TS-S04D168A November, 2004 Preliminary Specification 13. Ordering Information 13.1. Part Numbering System SXP 3101 SV Model Number 3101 PREFIX Application Code SV: SONET IR-2/SDH S-64.2b 10GBASE-ER/EW 13.2. Evaluation Board Kit For test purposes, Evaluation Board model number SK3101A and SP3101A may be ordered to use with the SXP3101 Series transceivers. SK3101A : SPX3101 XFP evaluation board SP3101A : XFP 2-wire serial interface evaluation kit 13.3. Ordering Number Code Table 13. SXP3101 Application Code P/N Distance SXP3101SV 40km SXP3101 Series Fiber E/O STD-SMF 1.55mm EML O/E ITU-T G.691 Telecordia GR-253 IEEE 802.3ae PIN S-64.2b IR-2 10GBASEER/EW Sumitomo Electric Industries, Ltd. Page 20 TS-S04D168A November, 2004 Preliminary Specification 14. Contact Information U.S.A. ExceLight Communications, 4021 Stirrup Creek Drive, Suite 200 Durham, NC 27703 Tel. +1-919-361-1600 / Fax. +1-919-361-1619 E-mail: info@excelight.com http://www.excelight.com Europe Sumitomo Electric Europe Ltd., 220, Centennial Park, Elstree, Herts, WD6 3SL, United Kingdom Tel. +44-208-953-8681 Fax. +44-208-207-5950 E-mail: photonics@sumielectric.com http://www.sumielectric.com Japan Sumitomo Electric Industries, Ltd. 1, Taya-cho, Sakae-ku, Yokohama, 244-8588 Tel. +81-45-853-7154 / Fax. +81-45-851-1932 E-mail: product-info@ppd.sei.co.jp http://www.sei.co.jp/Electro-optic/index.html SXP3101 Series Sumitomo Electric Industries, Ltd. Page 21