■Specifications
■Dimensions
※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105°C .
(unit : mm)
■Size List
30
RV : Rated voltage
(SV) : Surge (room temperature)
Specificationsfor
eachseries
4. SPECIFICATIONS FOR EACH SERIES
φd
L
F
15min.
19min.
φD
This is an even lower ESR series based on our SEP series. Suitable for
use with motherboards, servers, VGA, etc.
Lead free-flow is supported.
Marking : Polarity( ), Rated voltage, Rated Capacitance
(Purple) SANYO, OS-CON, Lot.No. SEPC.
4min.
※For the minimum packing quantity, please refer to page 51.
E9
E12
E13
F13
φD+0.5max.
8.0
8.0
8.0
10.0
Lmax. F
9.0
12.0
13.0
13.0
φd±0.05
0.6
0.6
0.6
0.6
3.5±0.5
3.5±0.5
3.5±0.5
5.0±0.5
Size Code
Conductive polymer type
SEPCSeries Large capacitance, low ESR
RV
（SV）
µ
F
2.5
（3.3）4.0
（5.2）6.3
（8.2）16.0
（18.4）
270
470
560
680
820
1500
2700
E9
E9 ， E13
F13
E9 ， E13
E13
F13
E9 ， E13
F13
F13
E12
F13
φd
L
15min. 4min.
19min.
φD
F
E12.E13.F13 Size E9 Size
E9 size flat rubber is used.
（＋）（＋）
Items Characteristics
-55°C to +105°C
M : ±20%
Less than or equal to the value of Table3
Less than or equal to the value of Table3
Less than or equal to the value of Table3
Within ±20%
1.5 times or less than an initial standard
1.5 times or less than an initial standard
Below an initial standard
Within ±20%
1.5 times or less than an initial standard
1.5 times or less than an initial standard
Below an initial standard (after voltage processing)
Within ±5%
Below an initial standard
Below an initial standard
Below an initial standard (after voltage processing)
Category temperature range
Tolerance on rated capacitance
Tangent of loss angle
Leakage current
ESR
Endurance
Damp heat (Steady state)
Characteristics of impedance
ratio at high temp. and low temp.
-55°C
+105°C
∆C/C
tanδ
ESR
Leakage current
∆C/C
tanδ
ESR
Leakage current
∆C/C
tanδ
ESR
Leakage current
Resistance to
soldering heat
Z / Z 20°C
Z / Z 20°C0.75 to 1.25
0.75 to 1.25
120Hz
120Hz
105°C, 2,000h, Rated
voltage applied
60°C, 90% RH,
1,000h,
No-applied voltage
Flow method
(260±5°C X 10s)
※1
Conditions
Based the value at
100KHz，+20°C
After 2 minutes
31
■Table3 SEPC Series Characteristics List
※1 Capacitance tolerance : M ±20%
※2 After 2 minutes
6SEPC470MX
4SEPC560MX
2SEPC560MX
2SEPC820MX
16SEPC270M
6SEPC470M
4SEPC560M
4SEPC680M
2R5SEPC820M
16SEPC470M
6SEPC680M
6SEPC1500M
4SEPC820M
2SEPC2700M
6.3
4
2.5
2.5
16
6.3
4
4
2.5
16
6.3
6.3
4
2.5
470
560
560
820
270
470
560
680
820
470
680
1500
820
2700
8
7
8
7
11
8
7
7
7
10
7
10
7
10
5700
6100
4700
6100
5000
5700
6100
6100
6100
6100
6640
5560
6640
5560
0.10
0.10
0.10
0.10
0.10
0.10
0.10
0.10
0.10
0.10
0.10
0.10
0.10
0.10
592
500
280
500
864
592
500
544
500
1504
857
1890
656
1350
Size
Code Part Number
※1
Rated
ripple current
100kHz (mArms) at 105°C
Tangent of
loss angle
(max.)
Leakage
current (µA)
(max.)※2
Rated
Voltage
(V)
Rated
Capacitance
(
µ
F)
Specificationsfor
eachseries
4. SPECIFICATIONS FOR EACH SERIES
ESR
100kHz to 300kHz
(mΩ) (max.)
Frequency coefficient for ripple current
Frequency
Coefficient 120Hz≦ f ＜1kHz
0.05 1kHz≦ f ＜10kHz
0.3 10kHz≦ f ＜100kHz
0.7 100kHz≦ f ≦500kHz
1
E9
E12
E13
F13