4. SPECIFICATIONS FOR EACH SERIES Conductive polymer type SEPC Series Large capacitance, low ESR Marking (Purple) Specifications Items Category temperature range Tolerance on rated capacitance Tangent of loss angle Leakage current 1 ESR Characteristics of impedance ratio at high temp. and low temp. Conditions 120Hz 120Hz After 2 minutes Based the value at 100KHz+20C 105C, 2,000h, Rated voltage applied Endurance 60C, 90% RH, 1,000h, No-applied voltage Damp heat (Steady state) Resistance to soldering heat Flow method (2605C X 10s) : Polarity( ), Rated voltage, Rated Capacitance SANYO, OS-CON, Lot.No. SEPC. Characteristics -55C to +105C M : 20% Less than or equal to the value of Table3 Less than or equal to the value of Table3 Less than or equal to the value of Table3 Z / Z 20C 0.75 to 1.25 -55C 0.75 to 1.25 Z / Z 20C +105C C/C Within 20% tan 1.5 times or less than an initial standard ESR 1.5 times or less than an initial standard Leakage current Below an initial standard C/C Within 20% tan 1.5 times or less than an initial standard ESR 1.5 times or less than an initial standard Leakage current Below an initial standard (after voltage processing) C/C Within 5% tan Below an initial standard ESR Below an initial standard Leakage current Below an initial standard (after voltage processing) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105C . Dimensions E12.E13.F13 Size E9 Size d d L F F 15min. D D Specifications for each series This is an even lower ESR series based on our SEP series. Suitable for use with motherboards, servers, VGA, etc. Lead free-flow is supported. 15min. 4min. L 19min. 4min. 19min. E9 size flat rubber is used. Size List RV SV F 270 470 560 680 820 1500 2700 2.5 3.3 RV : Rated voltage (SV) : Surge (room temperature) 4.0 6.3 16.0 5.2 8.2 18.4 E9 E13 E9 E9 E13 E9 E13 E13 F13 E12 F13 F13 F13 F13 For the minimum packing quantity, please refer to page 51. 30 (unit : mm) Size Code D+0.5max. Lmax. F d0.05 E9 E12 E13 F13 8.0 8.0 8.0 10.0 9.0 12.0 13.0 13.0 3.50.5 3.50.5 3.50.5 5.00.5 0.6 0.6 0.6 0.6 4. SPECIFICATIONS FOR EACH SERIES Table3 SEPC Series Characteristics List Size Code Rated Voltage (V) Rated Capacitance (F) ESR 100kHz to 300kHz (m) (max.) Rated ripple current 100kHz (mArms) at 105C Tangent of loss angle (max.) 6SEPC470MX 6.3 470 8 5700 0.10 592 4SEPC560MX 4 560 7 6100 0.10 500 2SEPC560MX 2.5 560 8 4700 0.10 280 2SEPC820MX 2.5 820 7 6100 0.10 500 270 11 5000 0.10 864 Part Number 1 Leakage current (A) (max.)2 E12 16SEPC270M 16 6SEPC470M 6.3 470 8 5700 0.10 592 4SEPC560M 4 560 7 6100 0.10 500 4SEPC680M 4 680 7 6100 0.10 544 2R5SEPC820M 2.5 820 7 6100 0.10 500 470 10 6100 0.10 1504 Specifications for each series E9 E13 16SEPC470M F13 1 2 16 6SEPC680M 6.3 680 7 6640 0.10 857 6SEPC1500M 6.3 1500 10 5560 0.10 1890 4SEPC820M 4 820 7 6640 0.10 656 2SEPC2700M 2.5 2700 10 5560 0.10 1350 Capacitance tolerance : M 20% After 2 minutes Frequency coefficient for ripple current Frequency Coefficient 120Hz f 1kHz 0.05 1kHz f 10kHz 0.3 10kHz f 100kHz 0.7 100kHz f 500kHz 1 31