INTEGRATED CIRCUITS DATA SHEET TDA8567Q 4 x 25 W BTL quad car radio power amplifier Product specification Supersedes data of 1997 Feb 12 File under Integrated Circuits, IC01 1998 Sep 23 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q FEATURES GENERAL DESCRIPTION * Requires very few external components The TDA8567Q is an integrated class-B output amplifier in a 23-lead Single-In-Line (SIL) plastic power package. It contains four amplifiers in BTL configuration, each with a gain of 26 dB. The output power is 4 x 25 W in a 4 load. * High output power * Low output offset voltage * Fixed gain * Diagnostic facility (distortion, short-circuit and temperature pre-warning) APPLICATIONS * The device is primarily developed for car radio applications. * Good ripple rejection * Mode select switch (operating, mute and standby) * Load dump protection * Short-circuit safe to ground and to VP and across the load * Low power dissipation in any short-circuit condition * Thermally protected * Reverse polarity safe * Electrostatic discharge protection * No switch-on/switch-off plop * Flexible leads * Low thermal resistance * Pin compatible with the TDA8568Q, except for the gain. QUICK REFERENCE DATA SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT VP operating supply voltage 6 14.4 18 V IORM repetitive peak output current - - 7.5 A Iq(tot) total quiescent current - 230 - mA Istb standby current - 0.2 100 A Isw switch-on current - - 80 A Zi input impedance 25 30 - k Po output power THD = 10% - 25 - W SVRR supply voltage ripple rejection Rs = 0 - 60 - dB cs channel separation Rs = 10 k - 50 - dB 25 26 27 dB Rs = 0 - - 120 V - - 150 mV Gv closed loop voltage gain Vn(o) noise output voltage VO DC output offset voltage ORDERING INFORMATION PACKAGE TYPE NUMBER NAME DESCRIPTION VERSION TDA8567Q DBS23P plastic DIL-bent-SIL power package; 23 leads (straight lead length 3.2 mm) SOT411-1 1998 Sep 23 2 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q BLOCK DIAGRAM handbook, full pagewidth IN1 MODE VP1 VP2 15 1 8 10 VP3 VP4 16 23 + 2 - OUT1+ 30 k + 4 - IN2 OUT1- Vref 11 + 7 - OUT2+ 30 k + SGND 12 TDA8567Q IN3 5 - 13 DIAGNOSTIC + 9 17 - OUT2- VDIAG OUT3+ 30 k + 19 - IN4 OUT3- Vref 14 + 22 - OUT4+ 30 k + 20 - 3 PGND1 6 PGND2 18 21 PGND3 PGND4 Fig.1 Block diagram. 1998 Sep 23 3 OUT4- MGG153 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q PINNING SYMBOL PIN DESCRIPTION VP1 1 supply voltage 1 OUT1+ 2 output 1+ PGND1 3 power ground 1 OUT1- 4 output 1- OUT2- 5 output 2- PGND2 6 OUT2+ handbook, halfpage VP1 1 OUT1+ 2 PGND1 3 OUT1- 4 power ground 2 OUT2- 5 7 output 2+ PGND2 6 VP2 8 supply voltage 2 OUT2+ 7 VDIAG 9 diagnostic output VP2 8 IN1 10 input 1 VDIAG 9 IN2 11 input 2 SGND 12 signal ground IN3 13 input 3 IN4 14 input 4 MODE 15 mode select switch input IN3 13 VP3 16 supply voltage 3 IN4 14 OUT3+ 17 output 3+ PGND3 18 power ground 3 OUT3- 19 output 3- OUT4- 20 output 4- PGND4 21 power ground 4 OUT4+ 22 output 4+ OUT3- 19 VP4 23 supply voltage 4 OUT4- 20 IN1 10 IN2 11 SGND 12 TDA8567Q MODE 15 VP3 16 OUT3+ 17 PGND3 18 PGND4 21 OUT4+ 22 VP4 23 MGG152 Fig.2 Pin configuration. 1998 Sep 23 4 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q FUNCTIONAL DESCRIPTION SHORT-CIRCUIT DIAGNOSTIC The TDA8567Q contains four identical amplifiers which can be used for bridge applications. The gain of each amplifier is fixed at 26 dB. When a short-circuit occurs at one or more outputs to ground or to the supply voltage, the output stages are switched off until the short-circuit is removed and the device is switched on again, with a delay of approximately 10 ms after removal of the short-circuit. During this short-circuit condition, pin 9 is continuously LOW. Mode select switch (pin 15) * Standby: low supply current (<100 A) When a short-circuit occurs across the load of one or more channels, the output stages are switched off during approximately 10 ms. After that time it is checked during approximately 50 s to determine whether the short-circuit is still present. Due to this duty cycle of 50 s/10 ms the average current consumption during this short-circuit condition is very low. * Mute: input signal suppressed * Operating: normal on condition. Since this pin has a low input current (<80 A), a low cost supply switch can be applied. To avoid switch-on plops, it is advised to keep the amplifier in the mute mode during 150 ms (charging of the input capacitors at pins 10, 11, 13 and 14). When switching from standby to mute, the slope should be at least 18 V/s. * External timing circuit (see Fig.3). During this short-circuit condition, pin 9 is LOW for 10 ms and HIGH for 50 s (see Fig.5). The protection circuits of all channels are coupled. This means that if a short-circuit condition occurs in one of the channels, all channels are switched off. Consequently, the power dissipation in any short-circuit condition is very low. Diagnostic output (pin 9) TEMPERATURE PRE-WARNING DYNAMIC DISTORTION DETECTOR (DDD) When the virtual junction temperature Tvj reaches 145 C, pin 9 goes LOW. This can be realized by: * Microprocessor control At the onset of clipping of one or more output stages, the dynamic distortion detector becomes active and pin 9 goes LOW. This information can be used to drive a sound processor or DC volume control to attenuate the input signal and so limit the distortion. The output level of pin 9 is independent of the number of channels that are clipping (see Fig.4). OPEN COLLECTOR OUTPUTS The diagnostic pin has an open collector output, so more devices can be tied together. An external pull-up resistor is needed. handbook, halfpage Vo +V handbook, halfpage P MGG155 0 10 k MODE 47 F V9 BZX79C/3.9V VP MGD959 0 Fig.3 Mode select switch circuitry. 1998 Sep 23 t Fig.4 Distortion detector waveform. 5 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q handbook, full pagewidthshort MGG156 circuit current t short-circuit over the load V9 10 ms VP t 50 s Fig.5 Short-circuit waveform. 1998 Sep 23 6 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL VP PARAMETER CONDITIONS supply voltage MIN. MAX. UNIT operating - 18 V non-operating - 30 V load dump protection; during 50 ms; tr 2.5 ms - 45 V Vsc(safe) short-circuit safe voltage - 18 V Vrp reverse polarity voltage - 6 V IOSM non-repetitive peak output current - 10 A IORM repetitive peak output current - 7.5 A Ptot total power dissipation - 60 W Tstg storage temperature -55 +150 C Tamb operating ambient temperature -40 +85 C Tvj virtual junction temperature - 150 C THERMAL CHARACTERISTICS SYMBOL PARAMETER VALUE UNIT Rth j-a thermal resistance from junction to ambient in free air 40 K/W Rth j-c thermal resistance from junction to case (see Fig.6) 1 K/W virtual junction handbook, halfpage OUT1 3.2 K/W OUT2 OUT3 3.2 K/W 3.2 K/W OUT4 3.2 K/W 0.2 K/W case MGG157 Fig.6 Equivalent thermal resistance network. QUALITY SPECIFICATION In accordance with "SNW-FQ-611E". The number of the quality specification can be found in the "Quality Reference Handbook". The handbook can be ordered using the code 9397 750 00192. 1998 Sep 23 7 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q DC CHARACTERISTICS VP = 14.4 V; Tamb = 25 C; measured in Fig.7; unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Supply VP supply voltage note 1 6 14.4 18 V Iq(tot) total quiescent current RL = - 230 360 mA Operating condition V15 mode select switch level 8.5 - VP V I15 mode select switch current V15 = 14.4 V - 30 80 A VO output voltage note 2 - 7.0 - V VO output offset voltage - - 150 mV 3.3 - 6.4 V - 7.0 - V - - 150 mV Mute condition V15 mode select switch level VO output voltage VO output offset voltage note 2 Standby condition V15 mode select switch level 0 - 2 V Istb standby current - 0.2 100 A Diagnostic V9 diagnostic output voltage during any fault condition - - 0.6 V Tvj temperature pre-warning V9 = 0.6 V - 145 - C Notes 1. The circuit is DC adjusted at VP = 6 to 18 V and AC operating at VP = 8.5 to 18 V. 2. At 18 V < VP < 30 V the DC output voltage 12VP. 1998 Sep 23 8 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q AC CHARACTERISTICS VP = 14.4 V; RL = 4 ; f = 1 kHz; Tamb = 25 C; measured in Fig.7; unless otherwise specified. SYMBOL Po THD PARAMETER output power total harmonic distortion CONDITIONS MIN. TYP. MAX. UNIT THD = 0.5% 16 19 - W THD = 10% 21 25 - W THD = 30% 28 35 - W VP = 13.2 V; THD = 0.5% - 15 - W VP = 13.2 V; THD = 10% - 21 - W Po = 1 W - 0.05 - % V9 0.6 V; note 8 - 10 - % Bp power bandwidth THD = 0.5%; Po = -1 dB with respect to 16 W - 20 to 20000 - Hz fro(l) low frequency roll-off at -1 dB; note 1 - 25 - Hz fro(h) high frequency roll-off at -1 dB 20 - - kHz Gv closed loop voltage gain 25 26 27 dB SVRR supply voltage ripple rejection on; note 2 50 - - dB mute; note 2 50 - - dB standby; note 2 80 - - dB 25 30 38 k on; note 3 - 85 120 V on; note 4 - 100 - V mute; note 5 - 60 - V note 6 45 - - dB - - 1 dB - - 2 mV Zi input impedance Vn(o) noise output voltage cs channel separation Gv channel unbalance Vo output signal in mute note 7 Notes 1. Frequency response externally fixed. 2. Vripple = Vripple(max) = 2 V (p-p); Rs = 0 . 3. B = 20 Hz to 20 kHz; Rs = 0 . 4. B = 20 Hz to 20 kHz; Rs = 10 k. 5. B = 20 Hz to 20 kHz; independent of Rs. 6. PO = 16 W; Rs = 10 k. 7. Vi = Vi(max) = 1 V (RMS). 8. Dynamic Distortion Detector (DDD) active, pin 9 is set to logic 0. 1998 Sep 23 9 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q TEST AND APPLICATION INFORMATION VP handbook, full pagewidth +14.4 V MODE 15 IN1 input 1 VP1 VP2 VP3 VP4 1 8 16 23 10 + 470 nF 100 nF 2 OUT1+ 4 OUT1- 7 OUT2+ 5 OUT2- 9 VDIAG 17 OUT3+ 19 OUT3- 22 OUT4+ 20 OUT4- 2200 F - RL = 4 30 k + - IN2 input 2 Vref 11 + 470 nF - RL = 4 30 k + SGND - 12 10 k TDA8567Q IN3 input 3 13 DIAGNOSTIC + 470 nF +VP diagnostic output - RL = 4 30 k + - IN4 input 4 Vref 14 + 470 nF - RL = 4 30 k + - 3 6 18 21 PGND1 PGND2 PGND3 PGND4 power ground (substrate) MGG158 Special care must be taken in the PCB-layout to separate pin 9 from the pins 10, 11 13 and 14 to minimize the crosstalk between the clip output and the inputs. To avoid switch-on plops, it is advised to keep the amplifier in the mute mode during a period of 150 ms (charging the input capacitors at pin 10, 11, 13 and 14). Fig.7 Application circuit diagram. 1998 Sep 23 10 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q Test information Figures 8 to 13 have the following conditions: VP = 14.4 V; RL = 4 ; f = 1 kHz; 80 kHz filter used; unless otherwise specified. MGD922 60 MGD921 300 handbook, halfpage handbook, halfpage Po (W) IP (mA) 40 200 (1) (2) 20 (3) 100 0 0 8 0 4 8 12 16 12 10 14 16 20 VP (V) VP (V) 18 (1) EIAJ. (2) 10%. (3) 0.5%. Fig.8 IP as a function of VP. Fig.9 Po as a function of VP. MGD923 10 MGD924 10 handbook, halfpage handbook, halfpage THD+N (%) THD+N (%) 1 1 f = 10 kHz 10-1 10-1 1 kHz 10 W 100 Hz 10-2 10 102 103 1W 104 Po (W) 10-2 10 105 Fig.10 THD + N as a function of Po. 1998 Sep 23 102 103 104 f (Hz) 105 Fig.11 THD + N as a function of frequency. 11 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q MGD925 -30 MGD926 -30 handbook, halfpage handbook, halfpage SVRR (dB) cs (dB) -50 -50 -70 -70 (1) (2) -90 10 102 103 104 f (Hz) -90 10 105 102 103 104 f (Hz) (1) channel 1 channel 2, channel 3 channel 4. (2) channels 1 and 2 channels 3 and 4. Fig.13 Channel separation as a function of frequency. Fig.12 SVRR as a function of frequency. 1998 Sep 23 12 105 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q PCB layout 111.76 handbook, full pagewidth 78.74 Pgnd 100 nF 2200 F - VP - - out 4 out1 + + 470 nF 470 nF - - out2 out 3 + + 10 k diag in 1 in sgnd 2 3 mode 4 MGK079 Dimensions in mm. Fig.14 PCB layout (component side). 1998 Sep 23 13 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q 111.76 handbook, full pagewidth 78.74 Pgnd 100nF 2200 F - VP - - out 4 out1 + + 470 nF 470 nF - - out2 out 3 + mode in 4 in sgnd 3 2 diag + 10 k 1 MGK080 Dimensions in mm. Fig.15 PCB layout (soldering side). 1998 Sep 23 14 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q PACKAGE OUTLINE DBS23P: plastic DIL-bent-SIL power package; 23 leads (straight lead length 3.2 mm) SOT411-1 non-concave Dh x D Eh view B: mounting base side d A2 A5 A4 E2 B j E E1 L2 L3 L1 1 23 L e1 Z bp e c Q v M w M e2 m 0 5 10 mm scale DIMENSIONS (mm are the original dimensions) UNIT A 2 mm A4 A5 bp c D (1) d D h E (1) e e1 e2 12.2 4.6 1.15 1.65 0.75 0.55 30.4 28.0 12 2.54 1.27 5.08 11.8 4.3 0.85 1.35 0.60 0.35 29.9 27.5 Eh E1 E2 j L L1 L2 L3 m Q v w x Z (1) 6 10.15 6.2 1.85 3.6 14.0 10.7 2.4 4.3 2.1 0.6 0.25 0.03 45 1.43 9.85 5.8 1.65 2.8 13.0 9.9 1.6 0.78 1.8 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION REFERENCES IEC JEDEC EIAJ ISSUE DATE 96-10-11 98-02-20 SOT411-1 1998 Sep 23 EUROPEAN PROJECTION 15 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. Repairing soldered joints Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 C, contact may be up to 5 seconds. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "Data Handbook IC26; Integrated Circuit Packages" (order code 9398 652 90011). Soldering by dipping or by wave The maximum permissible temperature of the solder is 260 C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 1998 Sep 23 16 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q NOTES 1998 Sep 23 17 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q NOTES 1998 Sep 23 18 Philips Semiconductors Product specification 4 x 25 W BTL quad car radio power amplifier TDA8567Q NOTES 1998 Sep 23 19 Philips Semiconductors - a worldwide company Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 160 1010, Fax. +43 160 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 689 211, Fax. +359 2 689 102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S, Tel. +45 32 88 2636, Fax. +45 31 57 0044 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615800, Fax. +358 9 61580920 France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex, Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427 Germany: Hammerbrookstrae 69, D-20097 HAMBURG, Tel. +49 40 23 53 60, Fax. +49 40 23 536 300 Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS, Tel. +30 1 4894 339/239, Fax. +30 1 4814 240 Hungary: see Austria India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia: PT Philips Development Corporation, Semiconductors Division, Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510, Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080 Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3, 20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5077 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Pakistan: see Singapore Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA, Tel. +48 22 612 2831, Fax. +48 22 612 2327 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000, Tel. +27 11 470 5911, Fax. +27 11 470 5494 South America: Al. Vicente Pinzon, 173, 6th floor, 04547-130 SAO PAULO, SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 821 2382 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 93 301 6312, Fax. +34 93 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZURICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +66 2 745 4090, Fax. +66 2 398 0793 Turkey: Talatpasa Cad. No. 5, 80640 GULTEPE/ISTANBUL, Tel. +90 212 279 2770, Fax. +90 212 282 6707 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 625 344, Fax.+381 11 635 777 For all other countries apply to: Philips Semiconductors, International Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 Internet: http://www.semiconductors.philips.com (c) Philips Electronics N.V. 1998 SCA60 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands 545102/750/02/pp20 Date of release: 1998 Sep 23 Document order number: 9397 750 04369