18-Bit, 1.33 MSPS PulSAR 10.5 mW ADC in MSOP/LFCSP AD7984 Data Sheet FEATURES APPLICATION DIAGRAM 2.9V TO 5V 2.5V IN+ REF VDD VIO SDI AD7984 10V, 5V, .. IN- ADA4941 SCK SDO GND CNV 1.8V TO 5V 3- OR 4-WIRE INTERFACE (SPI, CS DAISY CHAIN) 06973-001 18-bit resolution with no missing codes Throughput: 1.33 MSPS Low power dissipation: 10.5 mW at 1.33 MSPS INL: 2.25 LSB maximum Dynamic range: 99.7 dB typical True differential analog input range: VREF 0 V to VREF with VREF between 2.9 V to 5.0 V Allows use of any input range Easy to drive with the ADA4941 No pipeline delay Single-supply 2.5 V operation with 1.8 V/2.5 V/3 V/5 V logic interface Proprietary serial interface SPI/QSPI/MICROWIRETM/DSP compatible Ability to daisy-chain multiple ADCs and busy indicator 10-lead MSOP (MSOP-8 size) and 10-lead 3 mm x 3 mm LFCSP, SOT-23 size Figure 1. GENERAL DESCRIPTION The AD79841 is an 18-bit, successive approximation, analog-todigital converter (ADC) that operates from a single power supply, VDD. It contains a low power, high speed, 18-bit sampling ADC and a versatile serial interface port. On the CNV rising edge, the AD7984 samples the voltage difference between the IN+ and IN- pins. The voltages on these pins usually swing in opposite phases between 0 V and VREF. The reference voltage, REF, is applied externally and can be set independent of the supply voltage, VDD. APPLICATIONS Battery-powered equipment Data acquisition systems Medical instruments Seismic data acquisition systems The SPI-compatible serial interface also features the ability, using the SDI input, to daisy-chain several ADCs on a single 3-wire bus and provides an optional busy indicator. It is compatible with 1.8 V, 2.5 V, 3 V, and 5 V logic, using the separate VIO supply. The AD7984 is available in a 10-lead MSOP or a 10-lead LFCSP with operation specified from -40C to +85C. 1 Protected by U.S. Patent 6,703,961. Table 1. MSOP, LFCSP 14-/16-/18-Bit PulSAR(R) ADC Type 14-Bit 16-Bit 18-Bit 1 100 kSPS AD7940 AD7680 AD7683 AD7684 AD7988-1 AD7989-1 250 kSPS AD79421 AD76851 AD76871 AD7694 AD76911 400 kSPS to 500 kSPS AD79461 AD76861 AD76881 AD76931 AD7988-5 AD76901 AD7989-5 1000 kSPS ADC Driver AD79801 AD79831 ADA4941-x ADA4841-x AD79821 AD79841 ADA4941-x ADA4841-x Pin-for-pin compatible. Rev. B Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2007-2014 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD7984 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Driver Amplifier Choice ........................................................... 14 Applications ....................................................................................... 1 Single-to-Differential Driver .................................................... 15 Application Diagram ........................................................................ 1 Voltage Reference Input ............................................................ 15 General Description ......................................................................... 1 Power Supply............................................................................... 15 Revision History ............................................................................... 2 Digital Interface .......................................................................... 16 Specifications..................................................................................... 3 CS Mode, 3-Wire Without Busy Indicator ............................. 17 Timing Specifications .................................................................. 5 CS Mode, 3-Wire with Busy Indicator .................................... 18 Absolute Maximum Ratings ............................................................ 6 CS Mode, 4-Wire Without Busy Indicator ............................. 19 ESD Caution .................................................................................. 6 CS Mode, 4-Wire with Busy Indicator .................................... 20 Pin Configurations and Function Descriptions ........................... 7 Chain Mode Without Busy Indicator ...................................... 21 Typical Performance Characteristics ............................................. 8 Chain Mode with Busy Indicator ............................................. 22 Terminology .................................................................................... 11 Application Hints ........................................................................... 23 Theory of Operation ...................................................................... 12 Layout .......................................................................................... 23 Circuit Information .................................................................... 12 Evaluating the AD7984 Performance ...................................... 23 Converter Operation .................................................................. 12 Outline Dimensions ....................................................................... 24 Typical Connection Diagram.................................................... 13 Ordering Guide .......................................................................... 24 Analog Inputs .............................................................................. 14 REVISION HISTORY 7/14--Rev. A to Rev. B Changed QFN (LFCSP) to LFCSP .............................. Throughout Changes to Features Section and Table 1 ...................................... 1 Added Patent Note, Note 1 .............................................................. 1 Changes to Power Supply Section ................................................ 15 Changes to Evaluating the AD7984 Performance Section ........ 23 Updated Outline Dimensions ....................................................... 24 Changes to Ordering Guide .......................................................... 24 8/10--Rev. 0 to Rev. A Updated Outline Dimensions ....................................................... 24 Changes to Ordering Guide .......................................................... 24 11/07--Revision 0: Initial Version Rev. B | Page 2 of 24 Data Sheet AD7984 SPECIFICATIONS VDD = 2.5 V, VIO = 2.3 V to 5.5 V, REF = 5 V, TA = -40C to +85C, unless otherwise noted. Table 2. Parameter RESOLUTION ANALOG INPUT Voltage Range Absolute Input Voltage Common-Mode Input Range Analog Input CMRR Leakage Current at 25C Input Impedance ACCURACY No Missing Codes Differential Linearity Error Integral Linearity Error Transition Noise Gain Error, TMIN to TMAX3 Gain Error Temperature Drift Zero Error, TMIN to TMAX3 Zero Temperature Drift Power Supply Sensitivity THROUGHPUT Conversion Rate Transient Response AC ACCURACY Dynamic Range Signal-to-Noise, SNR Spurious-Free Dynamic Range, SFDR Total Harmonic Distortion4, THD Signal-to-(Noise + Distortion), SINAD Conditions Min 18 IN+ - IN- IN+, IN- IN+, IN- fIN = 450 kHz Acquisition phase Typ Max Unit Bits -VREF -0.1 VREF x 0.475 +VREF VREF + 0.1 VREF x 0.525 V V V dB1 nA 18 -1 -2.25 +1.5 +2.25 VREF x 0.5 67 200 See the Analog Inputs section -0.075 -700 VDD = 2.5 V 5% 0.95 0.022 -0.6 100 0.3 90 0 96.5 +700 1.33 290 Full-scale step VREF = 5 V fIN = 1 kHz, VREF = 5 V, TA = 25C fIN = 10 kHz fIN = 10 kHz fIN = 10 kHz, VREF = 5 V, TA = 25C +0.075 99.7 98.5 112.5 -110.5 98 Bits LSB2 LSB2 LSB2 % of FS ppm/C V ppm/C dB1 MSPS ns dB1 dB1 dB1 dB1 dB1 All specifications expressed in decibels are referred to a full-scale input FSR and tested with an input signal at 0.5 dB below full scale, unless otherwise specified. LSB means least significant bit. With the 5 V input range, one LSB is 38.15 V. 3 See Terminology section. These specifications include full temperature range variation but not the error contribution from the external reference. 4 Tested fully in production at fIN = 1 kHz. 1 2 Rev. B | Page 3 of 24 AD7984 Data Sheet VDD = 2.5 V, VIO = 2.3 V to 5.5 V, REF = 5 V, TA = -40C to +85C, unless otherwise noted. Table 3. Parameter REFERENCE Voltage Range Load Current SAMPLING DYNAMICS -3 dB Input Bandwidth Aperture Delay DIGITAL INPUTS Logic Levels VIL VIH VIL VIH IIL IIH DIGITAL OUTPUTS Data Format Pipeline Delay VOL VOH POWER SUPPLIES VDD VIO VIO Range Standby Current1, 2 Power Dissipation Energy per Conversion TEMPERATURE RANGE3 Specified Performance Conditions Min Typ Max Unit 5.1 520 V A 10 2 MHz ns 2.9 1.33 MSPS VIO > 3 V VIO > 3 V VIO 3 V VIO 3 V -0.3 0.7 x VIO -0.3 0.9 x VIO -1 -1 +0.3 x VIO VIO + 0.3 +0.1 x VIO VIO + 0.3 +1 +1 Serial 18 bits, twos complement Conversion results available immediately after completed conversion 0.4 VIO - 0.3 ISINK = +500 A ISOURCE = -500 A 2.375 2.3 1.8 Specified performance VDD and VIO = 2.5 V 1.33 MSPS throughput 2.5 1.1 10.5 7.9 TMIN to TMAX -40 With all digital inputs forced to VIO or GND as required. During acquisition phase. 3 Contact an Analog Devices, Inc., sales representative for the extended temperature range. 1 2 Rev. B | Page 4 of 24 2.625 5.5 5.5 14 +85 V V V V A A V V V V V mA mW nJ/sample C Data Sheet AD7984 TIMING SPECIFICATIONS TA = -40C to +85C, VDD = 2.37 V to 2.63 V, VIO = 2.3 V to 5.5 V, unless otherwise noted.1 Table 4. Parameter Conversion Time: CNV Rising Edge to Data Available Acquisition Time Time Between Conversions CNV Pulse Width (CS Mode) SCK Period (CS Mode) VIO Above 4.5 V VIO Above 3 V VIO Above 2.7 V VIO Above 2.3 V SCK Period (Chain Mode) VIO Above 4.5 V VIO Above 3 V VIO Above 2.7 V VIO Above 2.3 V SCK Low Time SCK High Time SCK Falling Edge to Data Remains Valid SCK Falling Edge to Data Valid Delay VIO Above 4.5 V VIO Above 3 V VIO Above 2.7 V VIO Above 2.3 V CNV or SDI Low to SDO D15 MSB Valid (CS Mode) VIO Above 3 V VIO Above 2.3 V CNV or SDI High or Last SCK Falling Edge to SDO High Impedance (CS Mode) SDI Valid Setup Time from CNV Rising Edge SDI Valid Hold Time from CNV Rising Edge (CS Mode) SDI Valid Hold Time from CNV Rising Edge (Chain Mode) SCK Valid Setup Time from CNV Rising Edge (Chain Mode) SCK Valid Hold Time from CNV Rising Edge (Chain Mode) SDI Valid Setup Time from SCK Falling Edge (Chain Mode) SDI Valid Hold Time from SCK Falling Edge (Chain Mode) SDI High to SDO High (Chain Mode with Busy Indicator) Min 300 250 750 10 Typ Max 500 Unit ns ns ns ns 10.5 12 13 15 ns ns ns ns 11.5 13 14 16 4.5 4.5 3 ns ns ns ns ns ns ns tSCK tSCKL tSCKH tHSDO tDSDO 9.5 11 12 14 ns ns ns ns 10 15 20 ns ns ns ns ns ns ns ns ns ns ns tEN tDIS tSSDICNV tHSDICNV tHSDICNV tSSCKCNV tHSCKCNV tSSDISCK tHSDISCK tDSDOSDI 5 2 0 5 5 2 3 15 See Figure 2 and Figure 3 for load conditions. Y% VIO1 IOL X% VIO1 tDELAY tDELAY VIH2 VIL2 1.4V TO SDO CL 20pF 500A IOH VIH2 VIL2 1FOR VIO 3.0V, X = 90, AND Y = 10; FOR VIO > 3.0V, X = 70, AND Y = 30. VIH AND MAXIMUM VIL USED. SEE DIGITAL INPUTS SPECIFICATIONS IN TABLE 3. 2MINIMUM Figure 2. Load Circuit for Digital Interface Timing Figure 3. Voltage Levels for Timing Rev. B | Page 5 of 24 06973-003 500A 06973-002 1 Symbol tCONV tACQ tCYC tCNVH tSCK AD7984 Data Sheet ABSOLUTE MAXIMUM RATINGS Table 5. Parameter Analog Inputs IN+, IN- to GND1 Supply Voltage REF, VIO to GND VDD to GND VDD to VIO Digital Inputs to GND Digital Outputs to GND Storage Temperature Range Junction Temperature JA Thermal Impedance 10-Lead MSOP 10-Lead LFCSP JC Thermal Impedance 10-Lead MSOP 10-Lead LFCSP Lead Temperatures Vapor Phase (60 sec) Infrared (15 sec) 1 Rating -0.3 V to VREF + 0.3 V or 130 mA -0.3 V to +6.0 V -0.3 V to +3.0 V +3 V to -6 V -0.3 V to VIO + 0.3 V -0.3 V to VIO + 0.3 V -65C to +150C 150C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION 200C/W 48.7C/W 44C/W 2.96C/W 215C 220C See the Analog Inputs section for an explanation of IN+ and IN-. Rev. B | Page 6 of 24 Data Sheet AD7984 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS VDD 2 10 VIO AD7984 9 SDI TOP VIEW (Not to Scale) 8 SCK 7 SDO 6 CNV IN+ 3 IN- 4 GND 5 IN- 4 GND 5 06973-004 REF 1 VDD 2 IN+ 3 AD7984 (EXPOSED PAD)* 9 SDI 8 SCK 7 SDO 6 CNV *EXPOSED PADDLE CAN BE CONNECTED TO GROUND. Figure 4. 10-Lead MSOP Pin Configuration 06973-005 10 VIO REF 1 Figure 5. 10-Lead LFCSP Pin Configuration Table 6. Pin Function Descriptions Pin No. 1 Mnemonic REF Type1 AI 2 3 4 5 6 VDD IN+ IN- GND CNV P AI AI P DI 7 8 9 SDO SCK SDI DO DI DI 10 VIO P 1 Description Reference Input Voltage. The REF range is 2.9 V to 5.1 V. This pin is referred to the GND pin and should be decoupled closely to the GND pin with a 10 F capacitor. Power Supply. Differential Positive Analog Input. Differential Negative Analog Input. Power Supply Ground. Convert Input. This input has multiple functions. On its rising edge, it initiates the conversions and selects the interface mode of the part: chain mode or CS mode. In CS mode, the SDO pin is enabled when CNV is low. In chain mode, the data should be read when CNV is high. Serial Data Output. The conversion result is output on this pin. It is synchronized to SCK. Serial Data Clock Input. When the part is selected, the conversion result is shifted out by this clock. Serial Data Input. This input provides multiple features. It selects the interface mode of the ADC as follows: Chain mode is selected if SDI is low during the CNV rising edge. In this mode, SDI is used as a data input to daisy-chain the conversion results of two or more ADCs onto a single SDO line. The digital data level on SDI is output on SDO with a delay of 18 SCK cycles. CS mode is selected if SDI is high during the CNV rising edge. In this mode, either SDI or CNV can enable the serial output signals when low. If SDI or CNV is low when the conversion is complete, the busy indicator feature is enabled. Input/Output Interface Digital Power. Nominally at the same supply as the host interface (1.8 V, 2.5 V, 3 V, or 5 V). AI = analog input, DI = digital input, DO = digital output, and P = power. Rev. B | Page 7 of 24 AD7984 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS VDD = 2.5 V, REF = 5.0 V, VIO = 3.3 V. 2.0 2.0 POSITIVE DNL: +0.63LSB NEGATIVE DNL: -0.34LSB 1.5 1.0 1.0 0.5 0.5 0 0 -0.5 -0.5 -1.0 -1.0 -1.5 -1.5 -2.0 0 65536 196608 131072 06973-038 DNL (LSB) 1.5 06973-032 INL (LSB) POSITIVE INL: +1.07LSB NEGATIVE INL: -0.73LSB -2.0 262144 0 65536 131072 CODE 262144 196608 CODE Figure 6. Integral Nonlinearity vs. Code Figure 9. Differential Nonlinearity vs. Code 60k 60k 55354 50k COUNTS 32350 31003 30k 20k 30k 20k 16593 14653 0 0 0 7 326 1C 1D 1E 1F 5708 326 20 21 22 23 24 25 6 0 0 26 27 28 06973-041 5992 0 0 2 69 1D 1E 1F 20 0 1801 CODE IN HEX 21 1378 37 22 23 24 25 26 27 0 0 28 29 06973-042 10k 10k CODE IN HEX Figure 7. Histogram of a DC Input at the Code Center Figure 10. Histogram of a DC Input at the Code Transition 0 100 fS = 1.33MSPS fIN = 10kHz -20 99 SNR = 98.2dB THD = -110.6dB SFDR = 112.5dB SINAD = 98.0dB -40 98 97 SNR (dB) -60 -80 -100 -120 96 95 94 93 -140 -160 -180 0 100 200 300 400 500 06973-039 92 06973-033 AMPLITUDE (dB of Full Scale) 48266 40k 40k COUNTS 48273 50k 91 90 -10 600 FREQUENCY (kHz) -9 -8 -7 -6 -5 -4 -3 INPUT LEVEL (dB of Full Scale) Figure 8. FFT Plot Figure 11. SNR vs. Input Level Rev. B | Page 8 of 24 -2 -1 0 Data Sheet AD7984 100 18 -100 17 -105 SNR 95 16 THD (dB) 90 ENOB (Bits) SNR, SINAD (dB) SINAD -110 ENOB 15 3.0 4.0 3.5 4.5 14 5.5 5.0 -120 2.5 06973-043 80 2.5 -115 REFERENCE VOLTAGE (V) 06973-045 85 3.0 3.5 4.0 4.5 5.5 5.0 REFERENCE VOLTAGE (V) Figure 12. SNR, SINAD, and ENOB vs. Reference Voltage Figure 15. THD vs. Reference Voltage 100 -100 98 96 THD (dB) SNR (dB) -105 94 -110 -115 -35 -15 5 25 45 65 85 -120 -55 105 06973-046 90 -55 06973-044 92 -35 TEMPERATURE (C) -15 5 25 45 65 85 105 125 TEMPERATURE (C) Figure 13. SNR vs. Temperature Figure 16. THD vs. Temperature 100 -80 -85 THD (dB) -90 90 -95 -100 -105 85 80 1 10 100 06973-040 -110 06973-034 SINAD (dB) 95 -115 1 1000 FREQUENCY (kHz) 10 100 FREQUENCY (kHz) Figure 14. SINAD vs. Frequency Figure 17. THD vs. Frequency Rev. B | Page 9 of 24 1000 AD7984 Data Sheet 2.5 2.5 IVDD OPERATING CURRENTS (mA) 1.5 1.0 IREF 0.5 0 2.375 2.425 2.475 2.575 2.525 1.5 1.2 IVDD + IVIO 1.1 1.0 0.9 0.8 0.7 06973-036 STANDBY CURRENTS (mA) 1.3 0.6 5 25 45 0.5 -35 -15 5 25 45 65 85 105 Figure 20. Operating Currents vs. Temperature 1.4 -15 IREF TEMPERATURE (C) Figure 18. Operating Currents vs. Supply -35 1.0 0 -55 2.625 VDD VOLTAGE (V) 0.5 -55 1.5 IVIO 06973-035 IVIO 2.0 06973-037 OPERATING CURRENTS (mA) IVDD 2.0 65 85 105 125 TEMPERATURE (C) Figure 19. Standby Currents vs. Temperature Rev. B | Page 10 of 24 125 Data Sheet AD7984 TERMINOLOGY Integral Nonlinearity Error (INL) INL refers to the deviation of each individual code from a line drawn from negative full scale through positive full scale. The point used as negative full scale occurs 1/2 LSB before the first code transition. Positive full scale is defined as a level 11/2 LSB beyond the last code transition. The deviation is measured from the middle of each code to the true straight line (see Figure 22). Differential Nonlinearity Error (DNL) In an ideal ADC, code transitions are 1 LSB apart. DNL is the maximum deviation from this ideal value. It is often specified in terms of resolution for which no missing codes are guaranteed. Zero Error Zero error is the difference between the ideal midscale voltage, that is, 0 V, from the actual voltage producing the midscale output code, that is, 0 LSB. Gain Error The first transition (from 100 ... 00 to 100 ... 01) should occur at a level 1/2 LSB above nominal negative full scale (-4.999981 V for the 5 V range). The last transition (from 011 ... 10 to 011 ... 11) should occur for an analog voltage 11/2 LSB below the nominal full scale (+4.999943 V for the 5 V range). The gain error is the deviation of the difference between the actual level of the last transition and the actual level of the first transition from the difference between the ideal levels. Spurious-Free Dynamic Range (SFDR) SFDR is the difference, in decibels (dB), between the rms amplitude of the input signal and the peak spurious signal. Effective Number of Bits (ENOB) ENOB is a measurement of the resolution with a sine wave input. It is related to SINAD as follows: ENOB = (SINADdB - 1.76)/6.02 and is expressed in bits. Noise-Free Code Resolution Noise-free code resolution is the number of bits beyond which it is impossible to distinctly resolve individual codes. It is calculated as Noise-Free Code Resolution = log2(2N/Peak-to-Peak Noise) and is expressed in bits. Effective Resolution Effective resolution is calculated as Effective Resolution = log2(2N/RMS Input Noise) and is expressed in bits. Total Harmonic Distortion (THD) THD is the ratio of the rms sum of the first five harmonic components to the rms value of a full-scale input signal and is expressed in decibels. Dynamic Range Dynamic range is the ratio of the rms value of the full scale to the total rms noise measured with the inputs shorted together. The value for dynamic range is expressed in decibels. It is measured with a signal at -60 dBF so that it includes all noise sources and DNL artifacts. Signal-to-Noise Ratio (SNR) SNR is the ratio of the rms value of the actual input signal to the rms sum of all other spectral components below the Nyquist frequency, excluding harmonics and dc. The value for SNR is expressed in decibels. Signal-to-(Noise + Distortion) Ratio (SINAD) SINAD is the ratio of the rms value of the actual input signal to the rms sum of all other spectral components that are less than the Nyquist frequency, including harmonics but excluding dc. The value of SINAD is expressed in decibels. Aperture Delay Aperture delay is the measurement of the acquisition performance and is the time between the rising edge of the CNV input and when the input signal is held for a conversion. Transient Response Transient response is the time required for the ADC to accurately acquire its input after a full-scale step function is applied. Rev. B | Page 11 of 24 AD7984 Data Sheet THEORY OF OPERATION IN+ SWITCHES CONTROL LSB MSB REF 131,072C 65,536C 2C 4C C SW+ C BUSY COMP GND 131,072C 65,536C 2C 4C C CONTROL LOGIC C OUTPUT CODE LSB MSB SW- 06973-011 CNV IN- Figure 21. ADC Simplified Schematic CIRCUIT INFORMATION The AD7984 is a fast, low power, single-supply, precise, 18-bit ADC using a successive approximation architecture and is capable of converting 1,330,000 samples per second (1.33 MSPS). The AD7984 provides the user with an on-chip track-and-hold and does not exhibit any pipeline delay or latency, making it ideal for multiple multiplexed channel applications. The AD7984 can be interfaced to any 1.8 V to 5 V digital logic family. It is available in a 10-lead MSOP or a tiny 10-lead LFCSP that allows space savings and flexible configurations. It is pin-for-pin-compatible with the 18-bit AD7982. CONVERTER OPERATION The AD7984 is a successive approximation ADC based on a charge redistribution DAC. Figure 21 shows the simplified schematic of the ADC. The capacitive DAC consists of two identical arrays of 18 binary-weighted capacitors, which are connected to the two comparator inputs. During the acquisition phase, terminals of the array tied to the input of the comparator are connected to GND via SW+ and SW-. All independent switches are connected to the analog inputs. Therefore, the capacitor arrays are used as sampling capacitors and acquire the analog signal on the IN+ and IN- inputs. When the acquisition phase is complete and the CNV input goes high, a conversion phase is initiated. When the conversion phase begins, SW+ and SW- are opened first. The two capacitor arrays are then disconnected from the inputs and connected to the GND input. Therefore, the differential voltage between the inputs IN+ and IN- captured at the end of the acquisition phase is applied to the comparator inputs, causing the comparator to become unbalanced. By switching each element of the capacitor array between GND and REF, the comparator input varies by binary-weighted voltage steps (VREF/2, VREF/4 ... VREF/262,144). The control logic toggles these switches, starting with the MSB, to bring the comparator back into a balanced condition. After the completion of this process, the part returns to the acquisition phase, and the control logic generates the ADC output code and a busy signal indicator. Because the AD7984 has an on-board conversion clock, the serial clock, SCK, is not required for the conversion process. Rev. B | Page 12 of 24 Data Sheet AD7984 Transfer Functions Table 7. Output Codes and Ideal Input Voltages Description FSR - 1 LSB Midscale + 1 LSB Midscale Midscale - 1 LSB -FSR + 1 LSB -FSR 011 ... 111 011 ... 110 011 ... 101 1 2 Analog Input VREF = 5 V +4.999962 V +38.15 V 0V -38.15 V -4.999962 V -5 V Digital Output Code (Hex) 0x1FFFF1 0x00001 0x00000 0x3FFFF 0x20001 0x200002 This is also the code for an overranged analog input (VIN+ - VIN- above VREF - VGND). This is also the code for an underranged analog input (VIN+ - VIN- below VGND). TYPICAL CONNECTION DIAGRAM 100 ... 010 100 ... 001 100 ... 000 -FSR -FSR + 1 LSB -FSR + 0.5 LSB +FSR - 1 LSB +FSR - 1.5 LSB ANALOG INPUT Figure 23 shows an example of the recommended connection diagram for the AD7984 when multiple supplies are available. 06973-012 Figure 22. ADC Ideal Transfer Function V+ REF1 2.5V 10F2 100nF V+ 1.8V TO 5V 100nF 15 0 TO VREF REF 2.7nF VDD V- AD7984 4 V+ 15 ADA48412, 3 SCK SDO IN- VREF TO 0 VIO SDI IN+ GND 3-WIRE INTERFACE CNV 2.7nF V- 4 NOTES 1SEE VOLTAGE REFERENCE INPUT SECTION FOR REFERENCE SELECTION. 2C REF IS USUALLY A 10F CERAMIC CAPACITOR (X5R). SEE RECOMMENDED LAYOUT IN FIGURE 40 AND FIGURE 41. 3SEE DRIVER AMPLIFIER CHOICE SECTION. 4OPTIONAL FILTER. SEE ANALOG INPUTS SECTION. Figure 23. Typical Application Diagram with Multiple Supplies Rev. B | Page 13 of 24 06973-013 ADC CODE (TWOS COMPLEMENT) The ideal transfer characteristic for the AD7984 is shown in Figure 22 and Table 7. AD7984 Data Sheet ANALOG INPUTS Figure 24 shows an equivalent circuit of the input structure of the AD7984. The two diodes, D1 and D2, provide ESD protection for the analog inputs, IN+ and IN-. Care must be taken to ensure that the analog input signal does not exceed the reference input voltage (REF) by more than 0.3 V. If the analog input signal exceeds this level, the diodes become forward-biased and start conducting current. These diodes can handle a forward-biased current of 130 mA maximum. However, if the supplies of the input buffer (for example, the supplies of the ADA4841 in Figure 23) are different from those of REF, the analog input signal may eventually exceed the supply rails by more than 0.3 V. In such a case (for example, an input buffer with a shortcircuit), the current limitation can be used to protect the part. When the source impedance of the driving circuit is low, the AD7984 can be driven directly. Large source impedances significantly affect the ac performance, especially THD. The dc performances are less sensitive to the input impedance. The maximum source impedance depends on the amount of THD that can be tolerated. The THD degrades as a function of the source impedance and the maximum input frequency. DRIVER AMPLIFIER CHOICE Although the AD7984 is easy to drive, the driver amplifier must meet the following requirements: * REF D1 RIN CIN The noise generated by the driver amplifier must be kept as low as possible to preserve the SNR and transition noise performance of the AD7984. The noise from the driver is filtered by the AD7984 analog input circuit's 1-pole, lowpass filter made by RIN and CIN or by the external filter, if one is used. Because the typical noise of the AD7984 is 36.24 V rms, the SNR degradation due to the amplifier is IN+ OR IN- D2 06973-014 CPIN GND SNR LOSS Figure 24. Equivalent Analog Input Circuit The analog input structure allows the sampling of the true differential signal between IN+ and IN-. By using these differential inputs, signals common to both inputs are rejected. 85 CMRR (dB) 80 * * 70 1 10 100 FREQUENCY (kHz) 1000 10000 06973-015 65 60 Figure 25. Analog Input CMRR vs. Frequency During the acquisition phase, the impedance of the analog inputs (IN+ or IN-) can be modeled as a parallel combination of capacitor, CPIN, and the network formed by the series connection of RIN and CIN. CPIN is primarily the pin capacitance. RIN is typically 400 and is a lumped component composed of serial resistors and the on resistance of the switches. CIN is typically 30 pF and is mainly the ADC sampling capacitor. During the sampling phase, where the switches are closed, the input impedance is limited to CPIN. RIN and CIN make a 1-pole, low-pass filter that reduces undesirable aliasing effects and limits noise. where: f-3dB is the input bandwidth, in megahertz, of the AD7984 (10 MHz) or the cutoff frequency of the input filter, if one is used. N is the noise gain of the amplifier (for example, 1 in buffer configuration). eN is the equivalent input noise voltage of the op amp, in nV/Hz. 90 75 36.24 = 20 log 36.24 2 + f -3dB (Ne N ) 2 2 For ac applications, the driver should have a THD performance commensurate with the AD7984. For multichannel multiplexed applications, the driver amplifier and the AD7984 analog input circuit must settle for a full-scale step onto the capacitor array at an 18-bit level (0.0004%, 4 ppm). In the data sheet of the amplifier, settling at 0.1% to 0.01% is more commonly specified. This may differ significantly from the settling time at an 18-bit level and should be verified prior to driver selection. Table 8. Recommended Driver Amplifiers Amplifier ADA4941-x ADA4841-x AD8021 AD8022 OP184 AD8655 AD8605, AD8615 Rev. B | Page 14 of 24 Typical Application Very low noise, low power single-to-differential Very low noise, small, and low power Very low noise and high frequency Low noise and high frequency Low power, low noise, and low frequency 5 V single supply, low noise 5 V single supply, low power Data Sheet AD7984 If an unbuffered reference voltage is used, the decoupling value depends on the reference used. For instance, a 22 F (X5R, 1206 size) ceramic chip capacitor is appropriate for optimum performance using a low temperature drift ADR43x reference. SINGLE-TO-DIFFERENTIAL DRIVER For applications using a single-ended analog signal, either bipolar or unipolar, the ADA4941-x single-ended-todifferential driver allows for a differential input into the part. The schematic is shown in Figure 26. R1 and R2 set the attenuation ratio between the input range and the ADC range (VREF). R1, R2, and CF are chosen depending on the desired input resistance, signal bandwidth, antialiasing, and noise contribution. For example, for the 10 V range with a 4 k impedance, R2 = 1 k and R1 = 4 k. R3 and R4 set the common mode on the IN- input, and R5 and R6 set the common mode on the IN+ input of the ADC. The common mode should be close to VREF/2. For example, for the 10 V range with a single supply, R3 = 8.45 k, R4 = 11.8 k, R5 = 10.5 k, and R6 = 9.76 k. R5 R6 R3 R4 +5V REF 10F +5.2V +2.5V Regardless, there is no need for an additional lower value ceramic decoupling capacitor (for example, 100 nF) between the REF and GND pins. POWER SUPPLY The AD7984 uses two power supply pins: a core supply (VDD) and a digital input/output interface supply (VIO). VIO allows direct interface with any logic between 1.8 V and 5.5 V. To reduce the number of supplies needed, VIO and VDD can be tied together. The AD7984 is independent of power supply sequencing between VIO and VDD. Additionally, it is very insensitive to power supply variations over a wide frequency range, as shown in Figure 27. 95 REF OUTN 15 2.7nF 15 IN VDD 90 AD7984 2.7nF OUTP 85 IN- GND FB ADA4941 -0.2V 75 R2 06973-016 R1 80 CF 70 65 Figure 26. Single-Ended-to-Differential Driver Circuit VOLTAGE REFERENCE INPUT 60 The AD7984 voltage reference input, REF, has a dynamic input impedance and should therefore be driven by a low impedance source with efficient decoupling between the REF and GND pins, as explained in the Layout section. When REF is driven by a very low impedance source (for example, a reference buffer using the AD8031 or the AD8605), a 10 F (X5R, 0805 size) ceramic chip capacitor is appropriate for optimum performance. Rev. B | Page 15 of 24 1 10 100 FREQUENCY (kHz) Figure 27. PSRR vs. Frequency 1000 06973-017 100nF IN+ REF PSRR (dB) 100nF 10V, 5V, .. If desired, a reference-decoupling capacitor with values as small as 2.2 F can be used with a minimal impact on performance, especially DNL. AD7984 Data Sheet DIGITAL INTERFACE Although the AD7984 has a reduced number of pins, it offers flexibility in its serial interface modes. When in CS mode, the AD7984 is compatible with SPI, QSPITM, digital hosts, and DSPs. In this mode, the AD7984 can use either a 3-wire or 4-wire interface. A 3-wire interface using the CNV, SCK, and SDO signals minimizes wiring connections useful, for instance, in isolated applications. A 4-wire interface using the SDI, CNV, SCK, and SDO signals allows CNV, which initiates the conversions, to be independent of the readback timing (SDI). This is useful in low jitter sampling or simultaneous sampling applications. When in chain mode, the AD7984 provides a daisy-chain feature using the SDI input for cascading multiple ADCs on a single data line similar to a shift register. The mode in which the part operates depends on the SDI level when the CNV rising edge occurs. The CS mode is selected if SDI is high, and the chain mode is selected if SDI is low. The SDI hold time is such that when SDI and CNV are connected, the chain mode is always selected. In either mode, the AD7984 offers the option of forcing a start bit in front of the data bits. This start bit can be used as a busy signal indicator to interrupt the digital host and trigger the data reading. Otherwise, without a busy indicator, the user must timeout the maximum conversion time prior to readback. The busy indicator feature is enabled * * Rev. B | Page 16 of 24 In CS mode if CNV or SDI is low when the ADC conversion ends (see Figure 31 and Figure 35). In chain mode if SCK is high during the CNV rising edge (see Figure 39). Data Sheet AD7984 CS MODE, 3-WIRE WITHOUT BUSY INDICATOR high for the maximum possible conversion time to avoid the generation of the busy signal indicator. When the conversion is complete, the AD7984 enters the acquisition phase and goes into standby mode. When CNV goes low, the MSB is output onto SDO. The remaining data bits are clocked by subsequent SCK falling edges. The data is valid on both SCK edges. Although the rising edge can be used to capture the data, a digital host using the SCK falling edge allows a faster reading rate, provided it has an acceptable hold time. After the 18th SCK falling edge or when CNV goes high (whichever occurs first), SDO returns to high impedance. This mode is usually used when a single AD7984 is connected to an SPI-compatible digital host. The connection diagram is shown in Figure 28, and the corresponding timing is given in Figure 29. With SDI tied to VIO, a rising edge on CNV initiates a conversion, selects the CS mode, and forces SDO to high impedance. When a conversion is initiated, it continues until completion irrespective of the state of CNV. This can be useful, for example, to bring CNV low to select other SPI devices, such as analog multiplexers; however, CNV must be returned high before the minimum conversion time elapses and then held CONVERT DIGITAL HOST CNV VIO SDI AD7984 DATA IN SDO 06973-018 SCK CLK Figure 28. CS Mode, 3-Wire Without Busy Indicator Connection Diagram (SDI High) SDI = 1 tCYC tCNVH CNV ACQUISITION tCONV tACQ CONVERSION ACQUISITION tSCK tSCKL 1 2 3 16 tHSDO 18 tSCKH tDSDO tEN SDO 17 D17 D16 D15 tDIS D1 D0 Figure 29. CS Mode, 3-Wire Without Busy Indicator Serial Interface Timing (SDI High) Rev. B | Page 17 of 24 06973-019 SCK AD7984 Data Sheet CS MODE, 3-WIRE WITH BUSY INDICATOR When the conversion is complete, SDO goes from high impedance to low impedance. With a pull-up on the SDO line, this transition can be used as an interrupt signal to initiate the data reading controlled by the digital host. The AD7984 then enters the acquisition phase and goes into standby mode. The data bits are then clocked out, MSB first, by subsequent SCK falling edges. The data is valid on both SCK edges. Although the rising edge can be used to capture the data, a digital host using the SCK falling edge allows a faster reading rate, provided it has an acceptable hold time. After the optional 19th SCK falling edge or when CNV goes high (whichever occurs first), SDO returns to high impedance. This mode is usually used when a single AD7984 is connected to an SPI-compatible digital host having an interrupt input. The connection diagram is shown in Figure 30, and the corresponding timing is given in Figure 31. With SDI tied to VIO, a rising edge on CNV initiates a conversion, selects the CS mode, and forces SDO to high impedance. SDO is maintained in high impedance until the completion of the conversion irrespective of the state of CNV. Prior to the minimum conversion time, CNV can be used to select other SPI devices, such as analog multiplexers, but CNV must be returned low before the minimum conversion time elapses and then held low for the maximum possible conversion time to guarantee the generation of the busy signal indicator. If multiple AD7984s are selected at the same time, the SDO output pin handles this contention without damage or induced latch-up. Meanwhile, it is recommended to keep this contention as short as possible to limit extra power dissipation. CONVERT VIO CNV AD7984 DATA IN SDO IRQ SCK 06973-020 SDI DIGITAL HOST 47k VIO CLK Figure 30. CS Mode, 3-Wire with Busy Indicator Connection Diagram (SDI High) SDI = 1 tCYC tCNVH CNV ACQUISITION tCONV tACQ CONVERSION ACQUISITION tSCK tSCKL 1 2 3 17 tHSDO 18 19 tSCKH tDSDO SDO D17 D16 tDIS D1 D0 Figure 31. CS Mode, 3-Wire with Busy Indicator Serial Interface Timing (SDI High) Rev. B | Page 18 of 24 06973-021 SCK Data Sheet AD7984 CS MODE, 4-WIRE WITHOUT BUSY INDICATOR but SDI must be returned high before the minimum conversion time elapses and then held high for the maximum possible conversion time to avoid the generation of the busy signal indicator. When the conversion is complete, the AD7984 enters the acquisition phase and goes into standby mode. Each ADC result can be read by bringing its SDI input low, which consequently outputs the MSB onto SDO. The remaining data bits are then clocked by subsequent SCK falling edges. The data is valid on both SCK edges. Although the rising edge can be used to capture the data, a digital host using the SCK falling edge allows a faster reading rate, provided it has an acceptable hold time. After the 18th SCK falling edge or when SDI goes high (whichever occurs first), SDO returns to high impedance and another AD7984 can be read. This mode is usually used when multiple AD7984s are connected to an SPI-compatible digital host. A connection diagram example using two AD7984s is shown in Figure 32, and the corresponding timing is given in Figure 33. With SDI high, a rising edge on CNV initiates a conversion, selects the CS mode, and forces SDO to high impedance. In this mode, CNV must be held high during the conversion phase and the subsequent data readback (if SDI and CNV are low, SDO is driven low). Prior to the minimum conversion time, SDI can be used to select other SPI devices, such as analog multiplexers, CS2 CS1 CONVERT CNV AD7984 SDO SDI AD7984 SCK DIGITAL HOST SDO SCK 06973-022 SDI CNV DATA IN CLK Figure 32. CS Mode, 4-Wire Without Busy Indicator Connection Diagram tCYC CNV ACQUISITION tCONV tACQ CONVERSION ACQUISITION tSSDICNV SDI(CS1) tHSDICNV SDI(CS2) tSCK tSCKL 1 2 16 3 tHSDO 18 19 20 34 35 36 tDSDO tEN SDO 17 tSCKH D17 D16 D15 tDIS D1 D0 D17 D16 Figure 33. CS Mode, 4-Wire Without Busy Indicator Serial Interface Timing Rev. B | Page 19 of 24 D1 D0 06973-023 SCK AD7984 Data Sheet CS MODE, 4-WIRE WITH BUSY INDICATOR but SDI must be returned low before the minimum conversion time elapses and then held low for the maximum possible conversion time to guarantee the generation of the busy signal indicator. When the conversion is complete, SDO goes from high impedance to low impedance. With a pull-up on the SDO line, this transition can be used as an interrupt signal to initiate the data readback controlled by the digital host. The AD7984 then enters the acquisition phase and goes into standby mode. The data bits are then clocked out, MSB first, by subsequent SCK falling edges. The data is valid on both SCK edges. Although the rising edge can be used to capture the data, a digital host using the SCK falling edge allows a faster reading rate, provided it has an acceptable hold time. After the optional 19th SCK falling edge or SDI going high (whichever occurs first), SDO returns to high impedance. This mode is usually used when a single AD7984 is connected to an SPI-compatible digital host with an interrupt input and when it is desired to keep CNV, which is used to sample the analog input, independent of the signal used to select the data reading. This independence is particularly important in applications where low jitter on CNV is desired. The connection diagram is shown in Figure 34, and the corresponding timing is given in Figure 35. With SDI high, a rising edge on CNV initiates a conversion, selects the CS mode, and forces SDO to high impedance. In this mode, CNV must be held high during the conversion phase and the subsequent data readback. (If SDI and CNV are low, SDO is driven low.) Prior to the minimum conversion time, SDI can be used to select other SPI devices, such as analog multiplexers, CS1 CONVERT VIO CNV AD7984 DATA IN SDO IRQ SCK 06973-024 SDI DIGITAL HOST 47k CLK Figure 34. CS Mode, 4-Wire with Busy Indicator Connection Diagram tCYC CNV ACQUISITION tCONV tACQ CONVERSION ACQUISITION tSSDICNV SDI tSCK tHSDICNV tSCKL 2 1 3 tHSDO 17 18 19 tSCKH tDIS tDSDO tEN SDO D17 D16 D1 Figure 35. CS Mode, 4-Wire with Busy Indicator Serial Interface Timing Rev. B | Page 20 of 24 D0 06973-025 SCK Data Sheet AD7984 CHAIN MODE WITHOUT BUSY INDICATOR readback. When the conversion is complete, the MSB is output onto SDO and the AD7984 enters the acquisition phase and goes into standby mode. The remaining data bits stored in the internal shift register are clocked by subsequent SCK falling edges. For each ADC, SDI feeds the input of the internal shift register and is clocked by the SCK falling edge. Each ADC in the chain outputs its data MSB first, and 18 x N clocks are required to read back the N ADCs. The data is valid on both SCK edges. Although the rising edge can be used to capture the data, a digital host using the SCK falling edge will allow a faster reading rate and consequently more AD7984s in the chain, provided the digital host has an acceptable hold time. The maximum conversion rate may be reduced due to the total readback time. This mode can be used to daisy-chain multiple AD7984s on a 3-wire serial interface. This feature is useful for reducing component count and wiring connections, for example, in isolated multiconverter applications or for systems with a limited interfacing capacity. Data readback is analogous to clocking a shift register. A connection diagram example using two AD7984s is shown in Figure 36, and the corresponding timing is given in Figure 37. When SDI and CNV are low, SDO is driven low. With SCK low, a rising edge on CNV initiates a conversion, selects the chain mode, and disables the busy indicator. In this mode, CNV is held high during the conversion phase and the subsequent data CONVERT CNV AD7984 SDO SDI DIGITAL HOST AD7984 DATA IN SDO B SCK A SCK 06973-026 SDI CNV CLK Figure 36. Chain Mode Without Busy Indicator Connection Diagram SDIA = 0 tCYC CNV ACQUISITION tCONV tACQ CONVERSION ACQUISITION tSCK tSCKL tSSCKCNV SCK 1 tHSCKCNV 2 3 16 18 17 tSSDISCK 19 20 DA17 DA16 34 35 36 DA1 DA0 tSCKH tHSDISCK tEN SDOA = SDIB DA17 DA16 DA15 DA1 DA0 DB17 DB16 DB15 DB1 DB0 SDOB Figure 37. Chain Mode Without Busy Indicator Serial Interface Timing Rev. B | Page 21 of 24 06973-027 tHSDO tDSDO AD7984 Data Sheet CHAIN MODE WITH BUSY INDICATOR completed their conversions, the SDO pin of the ADC closest to the digital host (see the AD7984 ADC labeled C in Figure 38) is driven high. This transition on SDO can be used as a busy indicator to trigger the data readback controlled by the digital host. The AD7984 then enters the acquisition phase and goes into standby mode. The data bits stored in the internal shift register are clocked out, MSB first, by subsequent SCK falling edges. For each ADC, SDI feeds the input of the internal shift register and is clocked by the SCK falling edge. Each ADC in the chain outputs its data MSB first, and 18 x N + 1 clocks are required to read back the N ADCs. Although the rising edge can be used to capture the data, a digital host using the SCK falling edge allows a faster reading rate and, consequently, more AD7984s in the chain, provided the digital host has an acceptable hold time. This mode can also be used to daisy-chain multiple AD7984s on a 3-wire serial interface while providing a busy indicator. This feature is useful for reducing component count and wiring connections, for example, in isolated multiconverter applications or for systems with a limited interfacing capacity. Data readback is analogous to clocking a shift register. A connection diagram example using three AD7984s is shown in Figure 38, and the corresponding timing is given in Figure 39. When SDI and CNV are low, SDO is driven low. With SCK high, a rising edge on CNV initiates a conversion, selects the chain mode, and enables the busy indicator feature. In this mode, CNV is held high during the conversion phase and the subsequent data readback. When all ADCs in the chain have CONVERT SDI CNV AD7984 SDO SDI CNV AD7984 SDO SDI AD7984 B SCK A SCK DIGITAL HOST SDO DATA IN C SCK IRQ 06973-028 CNV CLK Figure 38. Chain Mode with Busy Indicator Connection Diagram tCYC ACQUISITION tCONV tACQ ACQUISITION CONVERSION tSSCKCNV SCK tSCKH 1 2 tSSDISCK tHSCKCNV tEN SDOA = SDIB 3 4 tSCK 17 18 tHSDISCK DA17 DA16 DA15 19 20 21 35 36 37 38 39 tSCKL DA1 tDSDOSDI 55 DA0 tDSDOSDI DB17 DB16 DB15 DB1 DB0 DA17 DA16 DA1 DA0 DC17 DC16 DC15 DC1 DC0 DB17 DB16 DB1 DB0 DA17 DA16 tDSDOSDI SDOC 54 tDSDOSDI tHSDO tDSDO SDOB = SDIC 53 tDSDOSDI Figure 39. Chain Mode with Busy Indicator Serial Interface Timing Rev. B | Page 22 of 24 DA 1 DA0 06973-029 CNV = SDIA Data Sheet AD7984 APPLICATION HINTS LAYOUT The printed circuit board (PCB) that houses the AD7984 should be designed so that the analog and digital sections are separated and confined to certain areas of the board. The pinout of the AD7984, with its analog signals on the left side and its digital signals on the right side, eases this task. AD7984 At least one ground plane should be used. It can be common or split between the digital and analog sections. In the latter case, the planes should be joined underneath the AD7984. 06973-030 Avoid running digital lines under the device because these couple noise onto the die, unless a ground plane under the AD7984 is used as a shield. Fast switching signals, such as CNV or clocks, should not run near analog signal paths. Crossover of digital and analog signals should be avoided. Figure 40. Example Layout of the AD7984 (Top Layer) The AD7984 voltage reference input REF has a dynamic input impedance and should be decoupled with minimal parasitic inductances. This is done by placing the reference decoupling ceramic capacitor close to, ideally right up against, the REF and GND pins and connecting them with wide, low impedance traces. Finally, the power supplies VDD and VIO of the AD7984 should be decoupled with ceramic capacitors, typically 100 nF, placed close to the AD7984 and connected using short, wide traces to provide low impedance paths and to reduce the effect of glitches on the power supply lines. An example of layout following these rules is shown in Figure 40 and Figure 41. Other recommended layouts for the AD7984 are outlined in the documentation of the evaluation board for the AD7984 (EVAL-AD7984SDZ). The evaluation board package includes a fully assembled and tested evaluation board, documentation, and software for controlling the board from a PC via the EVAL-SDP-CB1Z. Rev. B | Page 23 of 24 06973-031 EVALUATING THE AD7984 PERFORMANCE Figure 41. Example Layout of the AD7984 (Bottom Layer) AD7984 Data Sheet OUTLINE DIMENSIONS 3.10 3.00 2.90 10 3.10 3.00 2.90 5.15 4.90 4.65 6 1 5 PIN 1 IDENTIFIER 0.50 BSC 0.95 0.85 0.75 15 MAX 1.10 MAX 0.30 0.15 0.70 0.55 0.40 0.23 0.13 6 0 091709-A 0.15 0.05 COPLANARITY 0.10 COMPLIANT TO JEDEC STANDARDS MO-187-BA Figure 42. 10-Lead Mini Small Outline Package [MSOP] (RM-10) Dimensions shown in millimeters 2.48 2.38 2.23 3.10 3.00 SQ 2.90 0.50 BSC 10 6 PIN 1 INDEX AREA 1.74 1.64 1.49 EXPOSED PAD 0.50 0.40 0.30 BOTTOM VIEW SEATING PLANE 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.30 0.25 0.20 PIN 1 INDICATOR (R 0.15) FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 02-05-2013-C 0.80 0.75 0.70 0.20 MIN 1 5 TOP VIEW 0.20 REF Figure 43. 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 3 mm x 3 mm Body, Very Very Thin, Dual Lead (CP-10-9) Dimensions shown in millimeters ORDERING GUIDE Model1, 2, 3 AD7984BRMZ AD7984BRMZ-RL7 AD7984BCPZ-RL7 AD7984BCPZ-RL EVAL-AD7984SDZ EVAL-SDP-CB1Z Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C Package Description 10-Lead MSOP 10-Lead MSOP 10-Lead LFCSP_WD 10-Lead LFCSP_WD Evaluation Board Evaluation Board Package Option RM-10 RM-10 CP-10-9 CP-10-9 Ordering Quantity Tube, 50 Reel, 1,000 Reel, 1,500 Reel, 5,000 Branding C60 C60 C60 C60 Z = RoHS compliant part. The EVAL-AD7984SDZ board can be used as a standalone evaluation board or in conjunction with the EVAL-SDP-CB1Z for evaluation/demonstration purposes. 3 The EVAL-SDP-CB1Z board allows a PC to control and communicate with all Analog Devices evaluation boards ending in the SD designator. 1 2 (c)2007-2014 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06973-0-7/14(B) Rev. B | Page 24 of 24