W83194AR-W
PRELIMINARY
Publication Release Date: May. 1999
- 6 - Revision 0.50
6.0 SERIAL CONTROL 0REGISTERS
The Pin column lists the affected pin number and the @PowerUp column gives the state at true
power up. Registers are set to the values shown only on true power up. "Command Code" byte and
"Byte Count" byte must be sent following the acknowledge of the Address Byte. Although the data
(bits) in these two bytes are considered "don't care", they must be sent and will be acknowledge.
After that, the below described sequence (Register 0, Register 1, Register 2, ....) will be valid and
acknowledged.
Frequency Table Setting by I2C (SEL5 ~ SEL0)
SEL5 SEL4 SEL3 SEL2 SEL1 SEL0
(MHz)
(MHz)
(MHz)
(MHz)
(MHz)
0 0 0 0 0 0 83.3 125 83 41.7 20.85
0 0 0 0 0 1 90 90 60 30 15
0 0 0 0 1 0 75 113 75 37.7 18.85
0 0 0 0 1 1 150 150 75 37.5 18.75
0 0 0 1 0 0 138 138 69 34.6 17.3
0 0 0 1 0 1 95.25 95.25 63.5 31.75 15.88
0 0 0 1 1 0 129 129 86 43 21.5
0 0 0 1 1 1 124 124 83 41.4 20.7
0 0 1 0 0 0 119 119 80 39.8 19.9
0 0 1 0 0 1 114 114 76 38 19
0 0 1 0 1 0 110 110 73.3 36.7 18.35
0 0 1 0 1 1 105 105 70 35 17.5
0 0 1 1 0 0 66.8 100.2 66.8 33.4 16.7
0 0 1 1 0 1 100.2 100.2 66.8 33.3 16.7
0 0 1 1 1 0 133.6 100.2 66.7 33.6 16.8
0 0 1 1 1 1 133.3 133.3 66.7 33.3 16.7
0 1 0 0 0 0 125 125 83.33 41.67 20.83
0 1 0 0 0 1 127 127 84.67 42.34 21.17
0 1 0 0 1 0 130 130 86.67 43.33 21.67
0 1 0 0 1 1 72 108 72 36.1 18.05
0 1 0 1 0 0 140 140 70 35.1 17.55
0 1 0 1 0 1 136 136 68 33.9 16.95
0 1 0 1 1 0 145 145 73 36.3 18.15
0 1 0 1 1 1 155 155 78 38.8 19.4
0 1 1 0 0 0 121 121 81 40.5 20.25
0 1 1 0 0 1 117 117 78 38.9 19.45
0 1 1 0 1 0 112 112 75 37.3 18.65
0 1 1 0 1 1 107 107 71 35.7 17.85
0 1 1 1 0 0 66.8 100.2 66.8 33.4 16.7
0 1 1 1 0 1 100.2 100.2 66.8 33.4 16.7
0 1 1 1 1 0 100.9 100.9 67.3 33.6 16.8
0 1 1 1 1 1 133.3 133.3 66.7 33.3 16.7