510
Other options available. For complete details
on variety, part numbers, installation and
specification, go to
ACTUAL SIZE
ACTUAL SIZE
www.southco.com/P2
Textured matte finish
R 1 (.040)
127.3 (5.01) Large P2
25.5
(1.00)
82.5 (3.25) Small P2
35.8
(1.41)
5.5 (.21)
R 1.5 (.06)
40
(1.58)
1.8 (.07)
Door thickness (see table)
17
(.65)
87.5±0.3 (3.45±.01)
Smaller P2
132±0.3 (5.20±.01) Larger P2
R Max.
1.5 (.06)
30.7±0.15
(1.210±.005)
Dimensions in millimeters (inch) unless otherwise stated
• Snap-in installation
• 2 sizes
Material and Finish
ABS plastic, black
Performance Details
Maximum static load:
Lifting / pulling: 1300 N (300 lbf)
Pushing / sliding: 450 N (100 lbf)
Flammability rating:
UL94-HB or UL94-V0
Operating temperature range:
-50°C (-60°F) to 60°C (140°F)
Notes
Performance details are based on
installation in a 1.2 (.048) thick
steel door. Maximum loads are
limited by door strength.
P2 Flush Pull
Low profile · Lift or pull · Single hole mount
Small
Large
Door Thickness Range Part Number
Small Large
Min. Max. UL94-HB UL94-V0 UL94-HB UL94-V0
1.0 (.040) 1.4 (.055) P2-41 P2-41-1 P2-51 P2-51-1
1.4 (.055) 1.8 (.070) P2-42 P2-42-1 P2-52 P2-52-1
1.8 (.070) 2.1 (.085) P2-43 P2-43-1 P2-53 P2-53-1
2.1 (.085) 2.5 (.100) P2-44 P2-44-1 P2-54 P2-54-1
Part Number Selection _________________________________________________________________________________
511
Other options available. For complete details
on variety, part numbers, installation and
specification, go to
Dimensions in millimeters (inch) unless otherwise stated www.southco.com/P2
Type B (Counter-Clockwise) Version Shown
P2 Flush Pull - Lockable
Low profile · Lift or pull · Single hole mount
110 +/- 0.3 (4.33 +/-0.012)
Door
Frame
11 +/- 0.3 (0.433 +/-0.012)
4x R 1.5
(.06)
30.7 +/- 0.3
(1.21 +/- 0.012)
• Snap-in installation
• Lockable
• Lock core included or
sold separately
• Cam sold separately
Material and Finish
Pull: ABS plastic, black
Lock parts:
Zinc alloy, powder coated. Brass.
Steel, zinc plated. Buna-N
Flammability Rating
UL94-HB or UL94-VO (See table)
Notes
For pulls without lock core, lock
core sold separately, see page 158.
Cam sold separately. See page 167.
Cam Forward
Grip
Cam Reversed
Grip
Cam Offset
25 (0.98) 25 (0.98) No Offset
21.8 (0.86) 28.2 (1.11) 3.2 (1.25)
18.6 (0.73) 31.4 (1.24) 6.4 (.250)
15.5 (0.61) 34.5 (1.36) 9.5 (.375)
116.2 (4.57)
Cam shown
in locked
position *
82.3 (3.24)
25.3 (1) 35.5 (1.4)
2 (0.08)
Typical Wall Thickness
23 (0.91)
Frame
Door
Cam
Length
Cam Grip
Cam forward
No Offset
(Straight) Cam
Cam reversed
Door Thickness (see table)
31.85 (1.25)
8.3 (0.33)
38.8
(1.53)
* Cam Ordered Separately
For Cam Part Numbers and
options see our Handbook page 167
or www.southco.com
P2 - 4 D M - R L
L Lock Style
2 With lock core, keyed alike CH751
(with two flat keys supplied)
9 Without lock core (See our handbook
page 183 or visit www.southco.com)
D Door Thickness Range
1 1.0 (.040) - 1.4 (.055)
2 1.4 (.055) - 1.8 (.070)
3 1.8 (.070) - 2.1 (.085)
4 2.1 (.085) - 2.5 (.100)
R Rotation
1 Type A (Clockwise to lock)
2 Type B (Counter-Clockwise to lock)
___________________________________________________________________________ Part Number Selection
M Material
1 UL94-V0 PC/ABS
2 UL94-HB ABS
159
Dimensions in millimeters (inch) unless otherwise stated
Installation Notes
1. Prepare panel and install latches
shown on page 164.
2. Latch should be in unlatched
position. The flats of the lock
extender should be aligned with
the flats on the housing.
3. Take a lock core and orient the
brass wafers to the internal
ramped area of the housing.
Push lock core into housing until
it stops.
4. Insert key into lock core and turn
to verify lock core is fully seated
and operating properly.
5. Install cam.
PK Lock Cores
SOUTHCO® Key-Choice System
Lock Cores - Disc Tumbler
Head Style
Lock Core Part Number
Phillips recess Slotted 4 mm Hex recess 8 mm Hex recess
Chrome plated PK-0-34027-01 PK-0-43489-01 PK-0-34323-01 PK-0-40374-01
Black powder coated PK-0-34027-50 PK-0-43489-50 PK-0-34323-50 PK-0-40374-50
Lock Cores - Tool Operable
Ramped area
of housing
Flats of lock
extender
Locked Position
Unlocked Position
Lock Core Installed (01 Rotation)
Locked Position
Southco logo on
this side of housing
Southco logo on
this side of housing
Unlocked Position
Lock Core Installed (09 Rotation)
Keys Part Number
Master Key (1) PK-24-01
Control (Removal) Key (1) PK-11-03
09 (Counter-Clockwise)
01 (Clockwise)
Lock Core Part Number
Keying Key code Bag qty Shuttered stainless steel scalp Non shuttered stainless steel scalp Non shuttered black powder coated Non shuttered chrome plated
KA CH751 1PK-39-72-13-KCH751 PK-132-13 PK-115-13 PK-116-13
KA RS001 1PK-39-72-13-RS001 PK-132-13-RS001 PK-29-15-13-RS001 PK-29-16-13-RS001
KD 10 CODES 10 PK-39-72-13-KD1010 PK-132-13-KD1010 PK-29-15-13-KD1010 PK-29-16-13-KD1010
KD 50 CODES 50 PK-39-72-13-KD1050 PK-132-13-KD1050 PK-29-15-13-KD1050 PK-29-16-13-KD1050
KD 125 CODES 125 PK-39-72-13-KD1125 PK-132-13-KD1125 PK-29-15-13-KD1125 PK-29-16-13-KD1125
MKKD 10 CODES 10 PK-39-72-13-MK1010 PK-132-13-MK1010 PK-29-15-13-MK1010 PK-29-16-13-MK1010
MKKD 50 CODES 50 PK-39-72-13-MK1050 PK-132-13-MK1050 PK-29-15-13-MK1050 PK-29-16-13-MK1050
MKKD 125 CODES 125 PK-39-72-13-MK1125 PK-132-13-MK1125 PK-29-15-13-MK1125 PK-29-16-13-MK1125
Key code selection
KA - Keyed Alike:
All lock cores are the same key code
KD - Keyed Differently:
Multiple key codes provided in a non-
master key system
MKKD - Master Keyed,
Keyed Differently:
Multiple key codes provided in a
master key system
Notes
Part Number includes 1 lock core and
2 keys
Lock Core Installation for CM-3 and CM-6 only (see page 164)
www.southco.com/PK
Keys Part Number
CH751 PK-10-01
RS001 PK-10-01-RS001
Other options available. For complete details
on variety, part numbers, installation and
specification, go to
167
Dimensions in millimeters (inch) unless otherwise stated
ACTUAL
SIZE #10
CM - S C L
CM Cam Locks
Cams & installation
www.southco.com/CM
Frame
Door
Max. door thickness
(see table page 187)
16.25 / 16.35
(.640 / .644)
Ø 19±0.2
(.75±.007)
Sealing
washer
(if included)
Housing
Mounting nut
Screw
& lock
washer
Door
Cam
Stop
washer
Installation Notes
1. Place sealing washer onto
housing (if included) and put
through the mounting hole
(see panel preparation).
2. Install mounting nut and tighten
to 5 Nm (44 inlbf).
3. Install cam to assembly
Properly orientate for rotation
and grip.
4. Install screw. Tighten to
4 Nm (35 inlbf).
16
(.62)
Length Length
Length
C - No hook
S
2 (.079)
Offset
C
L
L
L
H - Hook type 1
SL - Hook type 2
S
Offset
COffset
C
Order lock and cam separately
Cam part number (no lock)
For Lock selection see pages 164-166
C Cam Offset
0 No offset
2 3.2 (.125)
4 6.4 (.250)
6 9.5 (.375)
L Length
06 19 (.75)
10 31.8 (1.25)
14 44.5 (1.75)
S Style
C No hook
H Hook type 1
L Hook type 2
Material and Finish
Cam: Steel plated
16
(.62)
Length Length
Length
C - No hook
S
2 (.079)
Offset
C
L
L
L
H - Hook type 1
SL - Hook type 2
S
Offset
COffset
C
___________________________________________________________________________ Part Number Selection
See table
Other options available. For complete details
on variety, part numbers, installation and
specification, go to
