NL17SZ74 Single D Flip Flop The NL17SZ74 is a high performance, full function Edge triggered D Flip Flop, with all the features of a standard logic device such as the 74LCX74. Features * * * * * * * http://onsemi.com Extremely High Speed: tPD 2.6 ns (typical) at VCC = 5.0 V Designed for 1.65 V to 5.5 V VCC Operation MARKING DIAGRAM 5.0 V Tolerant Inputs - Interface Capability with 5.0 V TTL Logic LVTTL Compatible LVCMOS Compatible US8 US SUFFIX CASE 493 24 mA Balanced Output Sink and Source Capability Near Zero Static Supply Current (10 mA) Substantially Reduces System Power Requirements Replacement for NC7SZ74 * * Tiny Ultra Small Package Only 2.1 X 3.0 mm * High ESD Ratings: 2000 V Human Body Model M G MH M G = Date Code = Pb-Free Package High ESD Ratings: 200 V Machine Model * Chip Complexity: FET = 64 * Pb-Free Packages are Available PINOUT DIAGRAM TRUTH TABLE Inputs 8 7 6 5 2 3 4 VCC PR CLR Q Outputs PR CLR CP D Q Q Operating Mode L H L H L L X X X X X X H L H L H H Asynchronous Set Asynchronous Clear Undetermined H H H H h l H L L H Load and Read Register H H X NC NC Hold H h = High Voltage Level = High Voltage Level One Setup Time Prior to the Low-to-High Clock Transition L = Low Voltage Level l = Low Voltage Level One Setup Time Prior to the Low-to-High Clock Transition NC = No Change X = High or Low Voltage Level and Transitions are Acceptable = Low-to-High Transition = Not a Low-to-High Transition For ICC reasons, DO NOT FLOAT Inputs (c) Semiconductor Components Industries, LLC, 2006 April, 2006 - Rev. 4 1 CP D Q GND 1 LOGIC DIAGRAM PR 7 D 2 5 Q CP 1 3 Q 6 CLR VCC = 8, GND = 4 ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. Publication Order Number: NL17SZ74/D NL17SZ74 MAXIMUM RATINGS Symbol Value Unit DC Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage - Output in High or Low State (Note 1) -0.5 to VCC +0.5 V IIK DC Input Diode Current VI < GND -50 mA IOK DC Output Diode Current VO < GND -50 mA IO DC Output Sink Current 50 mA ICC DC Supply Current Per Supply Pin 100 mA IGND DC Ground Current Per Ground Pin 100 mA TSTG Storage Temperature Range -65 to +150 C C VCC Parameter TL Lead Temperature, 1 mm from Case for 10 Seconds 260 TJ Junction Temperature Under Bias +150 C qJA Thermal Resistance (Note 2) 250 C/W PD Power Dissipation in Still Air at 85C 250 mW MSL Moisture Sensitivity FR Flammability Rating Oxygen Index: 28 to 34 ESD Withstand Voltage Human Body Model (Note 3) Machine Model (Note 4) Charged Device Model (Note 5) VESD Level 1 UL 94 V-0 @ 0.125 in >2000 >200 N/A V Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. IO absolute maximum rating must be observed. 2. Measured with minimum pad spacing on an FR4 board, using 10 mm X 1 inch, 2 ounce copper trace with no air flow. 3. Tested to EIA/JESD22-A114-A. 4. Tested to EIA/JESD22-A115-A. 5. Tested to JESD22-C101-A. RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage Operating Data Retention Only Min Max Unit 1.65 1.5 5.5 5.5 V VI Input Voltage (Note 6) 0 5.5 V VO Output Voltage (HIGH or LOW State) 0 VCC V TA Operating Free-Air Temperature -40 +85 C Dt/DV Input Transition Rise or Fall Rate 0 0 0 20 10 5.0 ns/V VCC = 2.5 V 0.2 V VCC = 3.0 V 0.3 V VCC = 5.0 V 0.5 V 6. Unused inputs may not be left open. All inputs must be tied to a high-logic voltage level or a low-logic input voltage level. ORDERING INFORMATION Package Shipping US8 3000 / Tape & Reel NL17SZ74USG US8 (Pb-Free) 3000 / Tape & Reel TNL17SZ74USG US8 (Pb-Free) 3000 / Tape & Reel Device NL17SZ74US For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 2 NL17SZ74 DETAILED DEVICE ORDERING INFORMATION Device Nomenclature Device Order Number NL17SZ74US Logic Circuit Indicator No. of Gates per Package Temp Range Identifier Technology Device Function Package Suffix Package Type Tape and Reel Size NL 1 7 SZ 74 US US8 178 mm, 3000 Unit DC ELECTRICAL CHARACTERISTICS Symbol Parameter VIH High-Level Input Voltage VIL Low-Level Input Voltage Condition (V) Min 1.65 0.75 VCC 2.3 to 5.5 0.7 VCC Typ Max Min Max 0.7 VCC 0.25 VCC 0.25 VCC 2.3 to 5.5 0.3 VCC 0.3 VCC High-Level Output Voltage VIN = VIL or VIL IOH = 100 mA IOH = -3 mA IOH = -8 mA IOH = -12 mA IOH = -16 mA IOH = -24 mA IOH = -32 mA 1.65 to 5.5 1.65 2.3 2.7 3.0 3.0 4.5 VOL Low-Level Output Voltage VIN = VIH IOL = 100 mA IOL = 3 mA IOL = 8 mA IOL = 12 mA IOL = 16 mA IOL = 24 mA IOL = 32 mA 1.65 to 5.5 1.65 2.3 2.7 3.0 3.0 4.5 Input Leakage Current VIN = VCC or GND IOFF Power off Input Leakage Current ICC Quiescent Supply Current VCC - 0.1 1.29 1.9 2.2 2.4 2.3 3.8 Unit V 0.75 VCC 1.65 VOH IIN *40_C v TA v 85_C TA = 25_C VCC VCC 1.52 2.1 2.4 2.7 2.5 4.0 V 0.1 0.24 0.3 0.4 0.4 0.55 0.55 0.1 0.24 0.3 0.4 0.4 0.55 0.55 V 5.5 $0.1 $1.0 mA 5.5V or VIN = GND 0 1.0 10 mA VIN = VCC or GND 5.5 1.0 10 mA http://onsemi.com 3 0.008 0.10 0.12 0.15 0.19 0.30 0.30 VCC - 0.1 1.29 1.9 2.2 2.4 2.3 3.8 V NL17SZ74 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIII IIIIIIIIIIIII IIIIIIIIIII IIIIIII IIIII III IIIIIIIII III IIII IIIIIII III III III I III II I III II III I II IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIII IIIIIIII III IIIII III III I III II I III II III IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII III IIII IIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII III IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIII III IIIIIIII IIIII III III III III III IIII IIIIIIIIIIII III IIIIIIIIIIIIIIIIIIIIIII IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIII IIIIIIII III IIIII IIIIIIIIIIIIIII IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII III IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIII IIIIIIII III IIIII III III I III II I III II III IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIII III IIIIIIII IIIII III III III III III IIII IIIIIIIIIIII III IIIIIIIIIIIIIIIII IIIIII IIIIII III IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIII IIIIIIII III IIIII III III I III II I III II III IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII III IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIII IIIIIIII III IIIII IIIIIIIII IIIIII IIIIII IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIII III IIIIIIII IIIII III III III III III IIII IIIIIIIIIIII III IIIIIIIIIIIIIIIII IIIIII IIIIII III IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIII IIIIIIII III IIIII III III III III III IIII IIIIIII IIIIIIIIIIIIIIIII III IIIIII IIIIII IIII IIIIIIIIIIII III IIIIIIIIIIIIIIIIIIIIIIIIIIII AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) TA = 25C Symbol fMAX tPLH, tPHL tPLH, tPHL tS tH tW tREC Parameter Maximum Clock Frequency (50% Duty Cycle) (Waveform 1) Propagation Delay, CP to Q or Q (Waveform 1) Propagation Delay, PR or CLR to Q or Q (Waveform 2) Setup Time, D to CP (Waveform 1) Hold Time, D to CP (Waveform 1) Pulse Width, CP, CLR, PR (Waveform 3) Recover Time PR; CLR to CP (Waveform 3) VCC (V) 1.8 0.15 2.5 0.2 3.3 0.3 5.0 0.5 3.3 0.3 5.0 0.5 1.8 0.15 2.5 0.2 3.3 0.3 5.0 0.5 3.3 0.3 5.0 0.5 1.8 0.15 2.5 0.2 3.3 0.3 5.0 0.5 3.3 0.3 5.0 0.5 1.8 0.15 2.5 0.2 3.3 0.3 5.0 0.5 3.3 0.3 5.0 0.5 1.8 0.15 2.5 0.2 3.3 0.3 5.0 0.5 3.3 0.3 5.0 0.5 1.8 0.15 2.5 0.2 3.3 0.3 5.0 0.5 3.3 0.3 5.0 0.5 1.8 0.15 2.5 0.2 3.3 0.3 5.0 0.5 3.3 0.3 5.0 0.5 Test Conditions CL = 15 pF RD = 1 MW S1 = Open CL = 50 pF, RD = 500 W, S1 = Open CL = 15 pF RD = 1 MW S1 = Open CL = 50 pF, RD = 500 W, S1 = Open CL = 15 pF RD = 1 MW S1 = Open CL = 50 pF, RD = 500 W, S1 = Open CL = 15 pF RD = 1 MW S1 = Open CL = 50 pF, RD = 500 W, S1 = Open CL = 15 pF RD = 1 MW S1 = Open CL = 50 pF, RD = 500 W, S1 = Open CL = 15 pF RD = 1 MW S1 = Open CL = 50 pF, RD = 500 W, S1 = Open CL = 15 pF RD = 1 MW S1 = Open CL = 50 pF, RD = 500 W, S1 = Open Min 75 150 200 250 175 200 2.5 1.5 1.0 0.8 1.0 1.0 2.5 1.5 1.0 0.8 1.0 1.0 6.5 3.5 2.0 1.5 2.0 1.5 0.5 0.5 0.5 0.5 0.5 0.5 6.0 4.0 3.0 2.0 3.0 2.0 8.0 4.5 3.0 3.0 3.0 3.0 Typ 6.5 3.8 2.8 2.2 3.4 2.6 6.5 3.8 2.8 2.2 3.4 2.6 TA = -40 to 85C Max 12.5 7.5 6.5 4.5 7.0 5.0 14 9.0 6.5 5.0 7.0 5.0 Min 75 150 200 250 175 200 2.5 1.5 1.0 0.8 1.0 1.0 2.5 1.5 1.0 0.8 1.0 1.0 6.5 3.5 2.0 1.5 2.0 1.5 0.5 0.5 0.5 0.5 0.5 0.5 6.0 4.0 3.0 2.0 3.0 2.0 8.0 4.5 3.0 3.0 3.0 3.0 Max Unit MHz 13 8.0 7.0 5.0 7.5 5.5 14.5 9.5 7.0 5.5 7.5 5.5 ns ns ns ns ns MHz 7. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC / 2 (per flip-flop). CPD is used to determine the no-load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. CAPACITANCE (Note 8) Symbol Condition Typical Unit Input Capacitance VCC = 5.5 V 7.0 pF COUT Output Capacitance VCC = 5.5 V 7.0 pF CPD Power Dissipation Capacitance (Note 9) Frequency = 10 MHz VCC = 3.3 V VCC = 5.0 V 16 21 pF CIN Parameter 8. TA = +25C, f = 1 MHz 9. CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD) at no output loading and operating at 50% duty cycle. (See Figure 1) CPD is related to ICCD dynamic operating current by the expression: ICCD = CPD VCC fin + ICC(static). http://onsemi.com 4 NL17SZ74 Vcc D 50% 0V th ts Vcc tw CP 50% 0V fmax tPLH, tPHL VOH Q, Q 50% VOL WAVEFORM 1 - PROPAGATION DELAYS, SETUP AND HOLD TIMES tR = tF = 3.0 ns, 10% to 90%; f = 1 MHz; tW = 500 ns Vcc PR 50% 0V Vcc CLR 50% 0V tPLH tPHL Q 50% 50% VOL VOH tPLH Q 50% 50% tPHL WAVEFORM 2 - PROPAGATION DELAYS tR = tF = 3.0 ns, 10% to 90%; f = 1 MHz; tW = 500 ns Vcc tw PR, CLR 50% 0V trec Vcc 50% CP tw 0V WAVEFORM 3 - RECOVERY TIME tR = tF = 3.0 ns from 10% to 90%; f = 1 MHz; tw = 500 ns Output Reg: VOL 0.8 V, VOH 2.0 V Figure 1. AC Waveforms VCC PULSE GENERATOR DUT RT CL Figure 2. Test Circuit http://onsemi.com 5 RL NL17SZ74 PACKAGE DIMENSIONS US8 US SUFFIX CASE 493-02 ISSUE B NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION "A" DOES NOT INCLUDE MOLD FLASH, PROTRUSION OR GATE BURR. MOLD FLASH. PROTRUSION AND GATE BURR SHALL NOT EXCEED 0.140 MM (0.0055") PER SIDE. 4. DIMENSION "B" DOES NOT INCLUDE INTER-LEAD FLASH OR PROTRUSION. INTER-LEAD FLASH AND PROTRUSION SHALL NOT E3XCEED 0.140 (0.0055") PER SIDE. 5. LEAD FINISH IS SOLDER PLATING WITH THICKNESS OF 0.0076-0.0203 MM. (300-800 "). 6. ALL TOLERANCE UNLESS OTHERWISE SPECIFIED 0.0508 (0.0002 "). -X- A 8 J -Y- 5 DETAIL E B L 1 4 R S G P U C -T- SEATING PLANE D H 0.10 (0.004) T K N 0.10 (0.004) M T X Y R 0.10 TYP V M F DETAIL E DIM A B C D F G H J K L M N P R S U V MILLIMETERS MIN MAX 1.90 2.10 2.20 2.40 0.60 0.90 0.17 0.25 0.20 0.35 0.50 BSC 0.40 REF 0.10 0.18 0.00 0.10 3.00 3.20 0_ 6_ 5_ 10 _ 0.23 0.34 0.23 0.33 0.37 0.47 0.60 0.80 0.12 BSC INCHES MIN MAX 0.075 0.083 0.087 0.094 0.024 0.035 0.007 0.010 0.008 0.014 0.020 BSC 0.016 REF 0.004 0.007 0.000 0.004 0.118 0.126 0_ 6_ 5_ 10 _ 0.010 0.013 0.009 0.013 0.015 0.019 0.024 0.031 0.005 BSC SOLDERING FOOTPRINT* 3.8 0.015 0.50 0.0197 1.8 0.07 0.30 0.012 1.0 0.0394 SCALE 8:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 http://onsemi.com 6 For additional information, please contact your local Sales Representative. NL17SZ74/D