@ T2L FAST input and outputs @ Pulse widths stable and precise @ High output duty cycle @ &-pin DIP package @ Leads Thru-hole, J, Gull Wing or Tucked @ Available in pulse widths from 10 to 1000ns @ 10 T2L fan-out capacity design notes The "Mini Dip Series" Pulse Generator Modules developed by Engineered Components Company have been designed to pro- vide precise output pulse widths when triggered by variable width inputs. All required driving and output circuitry, as well as timing components, are contained in an 8-pin DIP package. These Pulse Generator Modules are of hybrid construction utilizing the proven technologies of active integrated circuitry and of passive networks utilizing capacitive, inductive and resistive elements. The MTBF on these modules, when calculated per MIL-HDBK-217 fora 50C ground fixed environment, is in of 3 million hours. These modules are compatible with TL FAST circuits and require no external components in order to obtain the specified output pulse. The MOFRPG-TTL is available in 38 pulse widths from 10 to 1000ns. These modules provide a stable TAL output pulse of the low profile TL COMPATIBLE Mini DIP FAST RECOVERY PULSE GENERATOR specified width for each positive input step. The generated pulse is inverted internally to provide a negative pulse as an additional output. lt is necessary only that the input be held low for at least 10ns, then high for at least 10ns to obtain the desired output pulse. The duration of the positive input pulse, after this time, has no effect on the output pulse width. No output pulse will occur on the negative input pulse transition, Pulse width tolerance is maintained as shown in the accompanying Part Number Table, when tested under the "Test Conditions" shown. Pulse width is measured atthe +1.5Vlevelon both leading and trailing edges. Rise and fall times are less than 4ns, when measured from .8V to 2.0. These modules are capable of driving 10 T#Lloads, Temperature coefficient of delay is approximately +1 00ppmi C over the operating temperature range of 0 to +70C. These Mini DIP Series* modules are packaged in an 8-pin DIP housing, molded of flame-proof Diallyl Phthalate per MIL-M-14, Type SDG-F, and are fully encapsulated in epoxy resin, Thru-hole, J, Gull Wing or Tucked Lead configurations are available on these modules (see Part Number Table note to specify). Leads meet the salderability requirements of MIL-STD-202, Method 208, Corner standoffs on the housing of the thru-hole lead version and lead design of the surface mount versions provide positive standoff from the printed circuit board to permit solder-fillet formation and flush cleaning of solder-flux residues for improved reliability. Marking consists of manufacturer's logo (EC), Federal Supply Code, part number, pin one (1) identification and date code of manufacture. All marking Is applied by silk screen process using white epoxy paint in accordance with MIL-STD-130, to meet the perma- nency of identification required by MIL-STD-202, Method 215. Ey cineeiaa components company 3580 SACRAMENTO DRIVE P.O. BOX 8121, SAN LUIS OBISPO, CA 93403-8121 (805) 544-3800 @ OUTSIDE CALIFORNIA (800) 235-4144 @ FAX (805) 544-8091BLOCK DIAGRAM IS SHOWN BELOW Veo INPUT g 5 Piece x x x | | | PULSE i | | GENERATOR ETE I Co aa F +OUT -oUT GROUND MECHANICAL DETAIL IS SHOWN BELOW #500 4 5 Fin Ne, Vv tN MDFPG- + = 6 Pin Mo. 1 4 {fo is | [ i ts ED pe a 2.010 AZo OM, yom om 100 ccs I 400 + yi oF | & i yl las Es a PF. Thru-hole Lead treo re" |[* ae peo Bh Li and pl 159 Ly Eas TYP. Gull Wing Lead FOZOTYP. + fa td ary) TYP. 030 re. | it | 285 wl.150 le 1vF J Lead | set rie i Uo ; Fs al 2R4 ag 00 j A he: TYP, | - 1 TSO TYP, Tucked Lead can Typo! laa TEST CONDITIONS 1. All measurements are made at 25C. 2. Vee supply voltage is maintained at 5.0V DC. 3. Allunits are tested using a FAST toggle-type positive input pulse and one FAST TL load at the output, 4, Input pulse width used is 10ns for all modules; repetition rate is approximately 200kHz. OPERATING SPECIFICATIONS * Voc supply voltage: . Veco supply current: Constant 0" in Gonstant 1"in ,,. Logic 1 Input: Voltage .. Current Logic 0 Input: Voltage . Current Logic 1 Voltage out: + eee ee es Logic 0 Voltage out: Operating temperature range: Storage temperature: * Pulse width increases or decreases approxim live decrease or increase of 5% in supply vo PART NUMBER TABLE Suffix Part Number with G (for Gull Wing Lead), Thru-hole Lead) or T (for Tucked Lead). Exampl 2 fF fF 8 ee eB ee a 4.75 to 5.25V DC 40m, typical 40m typical | 2V min; Veo max. 2fV = 20uA max. 5.6V = 100mA max. .BV max. .6mA max. @ vy = .5v. 2.7 min. .5V max, Oto 7O%C, 5 to +125C. ately 1% for a respec- ltage. J (for J Lead), F (for jes: MDOFAPG-TTL- 10G (Gull Wing), MDFRPG-TTL-25J (J Lead), MDFRPG-TTL-70F (Thru- hole Lead) or MDFRPG-TTL-100T (Tucked Lead). ; Maximum Part Number err a Rep. Rate {in Mhz} MDFRPG-TTL-10 10 +1 60.0 MDFRPG-TTL-11 11 +1 56,0 MDBFRPG-TTL-12 12 +1 53.0 MOFRPG-TTL-13 13 41 51.0 MDFRPG-TTL-14 14 +7 48.0 MDFRPG-TTL-15 15 +71 46.0 | MDFRPG-TTL-16 16 +71 44,0 MDFRPG-TTL-17 Ws+d 427.0 MDFRPG-TTL-18 16 +1 40,0 MOFRPG-TTL-19 9 +14 38.0 MOFRPG-TTL-20 20 +1 37.0 MDFRPG-TTL-21 2147 35.0 MDBFRPG-TTL-22 22+] 34.0 MDFRPG-TTL-23 2a +] 33.0 MDBFRPG-TTL-24 24 41 32.0 MDFRPG-TTL-25 25 +1 21.0 MDFRPG-TTL-30 30 41 26.0 MDFRPG-TTL-35 35 +1.5 23.0 MDBFRPG-TTL-40 40 +1.5 20.0 MBFRPG-TTL-45 45 +1.5 18.0 MDFRPG-TTL-50 5O + 1.5 17.0 MOFRPG-TTL-60 60 +1.5 14.5 MDFRPG-TTL-70 7O +2 12.5 MDFRPG-TTL-75 75 +2 11.5 MDFRPG-TTL-80 a0 +2 11.0 MDFRPG-TTL-90 90 +23 9.5 MOFRPG-TTL-100 100 +3 6.5 MDBFRPG-TTL-150 150 =4 6.0 MDFRPG-TTL-2700 200 +6 4.5 MDFRPG-TTL-250 250 +7 3.5 MDFRPG-TTL-300 300 +95 3.0 MDFRPG-TTL-400 400 +10 ZZ MDBFRPG-TTL-500 BOO +10 1.8 MOBFRPG-TTL-600 600 +14 1.6 MOFRPG-TTL-700 FOO +16 1.3 MDFRPG-TTL-800 800 + 18 1.1 MIDFRPG-TTL-S00 900 +20 1.0 MDBFRPG-TTL-1000 1000 +22 0.9 All modules can be operated up lo the maximum pulse rate specilied in the Part Number Table with pulse wioths as low as 10ns and pulse spacing as low as 1Ons, Since pulse width accuracies may be somewhat degraded al high pulse rates, itis suggested that the module be evaluated under the specilic operating conditions, Special modules can be readily manufactured to improve accura- cies and/or provide customer specified pulse widths for specific applications. Cala log No. C/O21588R