929841-01-10-30 - 3M - Datasheet.Directory

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ Thru-Board Socket

.100″ and .100″ × .100″ Straight, Solder Tails 929 Series

Physical

Electrical

Environmental

Insulation Glass Filled Polyester (PET)

Material:

Flammability: UL 94V-0

Color: Gray

Contact

Material: Copper Alloy

Plating

Underplating: 100 μ″ [ 2.54 μm ] Nickel

Wiping Area: See ordering information options for thickness

Solder Tails: 100 μ″ [ 2.54 μm ] tin lead or 200 μ" [ 5.08μm ] matte tin

Marking: None

Current Rating: 2 A

Insulation Resistance: > 1 × 109Ω at 500 VDC

Withstanding Voltage: 1000 VRMS at Sea Level

Temperature Rating: -55°C to +105°C

Process Rating: 260°C, (profile per J-STD-020C)

Moisture Sensitivity Level: 1 (per J-STD-020C)

• 3-40 contacts on one row, 4-80 on two row

• Single hole board preparation simplifies board

layout

• No solder mask preparation speeds

manufacturing assembly

• Top mounting allows single pass for wave

soldering

•See Regulatory Information Index (RIA)

for chemical compliance information

TS-0814-05

Sheet 1 of 2

Date Modified: March 15, 2007

UL File No.: E68080

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

Notes:

1. It is recommended that the plated thru-hole on the ends be .062″ [1.57] to .063″ [1.60]. This will prevent the connector from floating during the wave soldering

process.

2. Integral solder mask plugs are removed after soldering by using the 3M™ Hand Tool 929013 with the 3M™ Molded Head 929025-0X-XX or 3M™ Hand Tool

929012 with the 3M™ Press 929050.

3. Do not hand solder this connector because the solder heat and volume of solder cannot be adequately controlled. This wouldmake the integral plugs difficult

or impossible to remove.

4. The connector should be flow soldered such that it enters the solder wave, end first (width).

3M™ Thru-Board Socket

.100″ and .100″ × .100″ Straight, Solder Tails 929 Series

Contact

Quantity

Dimension A

+0.00 [ +0.00 ]

-.025 [ -.064 ]

1 Row 2 Row

04 0.20 [ 5.08 ]

03 06 0.30 [ 7.62 ]

04 08 0.40 [ 10.16 ]

05 10 0.50 [ 12.70 ]

06 12 0.60 [ 15.24 ]

07 14 0.70 [ 17.78 ]

08 16 0.80 [ 20.32 ]

09 18 0.90 [ 22.86 ]

10 20 1.00 [ 25.40 ]

11 22 1.10 [ 27.94 ]

12 24 1.20 [ 30.48 ]

13 26 1.30 [ 33.02 ]

14 28 1.40 [ 35.56 ]

15 30 1.50 [ 38.10 ]

16 32 1.60 [ 40.64 ]

17 34 1.70 [ 43.18 ]

18 36 1.80 [ 45.72 ]

19 38 1.90 [ 48.26 ]

20 40 2.00 [ 50.80 ]

21 42 2.10 [ 53.34 ]

22 44 2.20 [ 55.88 ]

23 46 2.30 [ 58.42 ]

24 48 2.40 [ 60.96 ]

25 50 2.50 [ 63.50 ]

26 52 2.60 [ 66.04 ]

27 54 2.70 [ 68.58 ]

28 56 2.80 [ 71.12 ]

29 58 2.90 [ 73.66 ]

30 60 3.00 [ 76.20 ]

31 62 3.10 [ 78.74 ]

32 64 3.20 [ 81.28 ]

33 66 3.30 [ 83.82 ]

34 68 3.40 [ 86.36 ]

35 70 3.50 [ 88.90 ]

36 72 3.60 [ 91.44 ]

37 74 3.70 [ 93.98 ]

38 76 3.80 [ 96.52 ]

39 78 3.90 [ 99.06 ]

40 80 4.00 [ 101.60 ]

TS-0814-05

Sheet 2 of 2

.0 .00 .000

inch ±.1 ±.01 ±.005

[ ] Dimensions for Reference

Only

Tolerance Unless Noted

[mm]

Inch

.125 ±

[ 3.18 ]

.010

.005

.235

[ 5.97 ]

.09 Ref

[ 2.3 ] .062

[ 1.57 ] .100 Ref

[ 2.54 ]

.025 X .010 Typ

[ 0.64 X 0.25 ] Integral Solder

Mask Plugs

(See Note 1)

.015

[ 0.38 ]

.130

[ 3.30 ] .060

[ 1.52 ]

.040

[ 1.02 ]

.100 ± .003

[ 2.54 ]

See Note 1

.075 Typ

[ 1.91 ]

Pad Size

.085 Typ

[ 2.16 ]

Pad Size

Recommended Solder

Flow Direction

.040 Sq Typ

[ 1.02 ]

.100

[ 2.54 ]

[ 1.65]

∅ .065 ± Typ

.005

.002

Recommended Mounting Hole Pattern

.100 ± .003

[ 2.54 ]

.100 ± .003

[ 2.54 ]

[ 1.65]

∅ .065 ± Typ.005

.002

.085 Typ

[ 2.16 ]

Pad Size

.075 Typ

[ 1.91 ]

Pad Size

See Note 1

+.010

-.005

.125

[ 3.18 ]

.160

[ 4.06 ]

.100 Ref

[ 2.54 ]

.040

[ 1.02 ]

Recommended Solder

Flow Direction

A.100

[ 2.54 ]

.040 Sq Typ

[ 1.02 ]

.200

[ 5.08 ]

Ordering Information

2 Row

842 = Gold

1 Row

841 = Gold Contact Quantity:

(per row) see table

Gold Plating Thickness:

10 = Wiping Area 10 µ" [0.25 µm] gold with tin-lead tails (RIA E3 & C2 apply)

30 = Wiping Area 30 µ" [0.76 µm] gold with tin-lead tails (RIA E3 & C2 apply)

RA = 10 µ" [0.25 µm] gold wiping area with matte tin tails (RIA E1 & C1 apply)

RB = 30 µ" [0.76 µm] gold wiping area with matte tin tails (RIA E1 & C1 apply)

929XXX-01-XX-XX

Plating Options:

Regulatory Information Appendix

3M Electronic Solutions Division/Interconnect

EUROPE

Appendix E1: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product is RoHS Compliant 2005/95/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in

excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/

EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this

information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E2: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is

compliant by exemption under EU Commission Decision 2005/747/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in

excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/

EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this

information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E3: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as

amended by Commission Decision 2005/618/EC.

This product contains lead in the solder tail area in excess of the maximum concentration value allowed.

Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon

information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E4: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is

compliant by exemption under EU Commission Decision 2005/17/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in

excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision

2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in

writing, this information represents 3M’s best knowledge and belief based upon information provided by third party

suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

RIA-2217-A

CHINA

Appendix C1: China RoHS

Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits

for Certain Hazardous Substances in Electronic Information Products.

This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,

means that the product or part does not contain any of the following substances in excess of the following maximum

concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium,

polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise

stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by

third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix C2: China RoHS

Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits

for Certain Hazardous Substances in Electronic Information Products.

This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,

means that the product or part does contain a substance, as detailed in the chart below, in excess of the following

maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent

chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless

otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information

provided by third party suppliers to 3M.

The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an

extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform

with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in

accordance with the product Warranty stated below.

Important Notice

All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the

accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended

application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s

current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in

writing, by an authorized officer of 3M.

Warranty; Limited Remedy; Limited Liability.

This product will be free from defects in material and manufacture for a period of ninety (90) days from the time of purchase. 3M MAKES NO

OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s

option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for

any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.

Name and Content of Hazardous Substances or Elements

Electronic Solutions Division

6801 River Place Blvd.

Austin, TX 78726-9000

800/225-5373