REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
a
Low Cost ⴞ2
g/
ⴞ10
g
Dual Axis
iMEMS
®
Accelerometers
with Digital Output
ADXL202/ADXL210
FEATURES
2-Axis Acceleration Sensor on a Single IC Chip
Measures Static Acceleration as Well as Dynamic
Acceleration
Duty Cycle Output with User Adjustable Period
Low Power <0.6 mA
Faster Response than Electrolytic, Mercury or Thermal
Tilt Sensors
Bandwidth Adjustment with a Single Capacitor Per Axis
5 m
g
Resolution at 60 Hz Bandwidth
+3 V to +5.25 V Single Supply Operation
1000
g
Shock Survival
APPLICATIONS
2-Axis Tilt Sensing
Computer Peripherals
Inertial Navigation
Seismic Monitoring
Vehicle Security Systems
Battery Powered Motion Sensing
A
IN
2 =
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700 World Wide Web Site: http://www.analog.com
Fax: 781/326-8703 © Analog Devices, Inc., 1999
FUNCTIONAL BLOCK DIAGRAM
DEMOD
RFILT
32kV
RFILT
32kV
OSCILLATOR
X SENSOR
Y SENSOR
ADXL202/
ADXL210
X OUT
Y OUT
SELF TEST
XFILT
VDD
VDD
CX
+3.0V TO +5.25V
CDC
COM YFILT T2
CYRSET
C
O
U
N
T
E
R
mP
T2
T1
A(
g
) = (T1/T2 – 0.5)/12.5%
0
g
= 50% DUTY CYCLE
T2 = RSET/125MV
DEMOD
DUTY
CYCLE
MODULATOR
(DCM)
GENERAL DESCRIPTION
The ADXL202/ADXL210 are low cost, low power, complete
2-axis accelerometers with a measurement range of either
±2 g/±10 g. The ADXL202/ADXL210 can measure both dy-
namic acceleration (e.g., vibration) and static acceleration (e.g.,
gravity).
The outputs are digital signals whose duty cycles (ratio of pulse-
width to period) are proportional to the acceleration in each of
the 2 sensitive axes. These outputs may be measured directly
with a microprocessor counter, requiring no A/D converter or
glue logic. The output period is adjustable from 0.5 ms to 10 ms
via a single resistor (R
SET
). If a voltage output is desired, a
voltage output proportional to acceleration is available from the
X
FILT
and Y
FILT
pins, or may be reconstructed by filtering the
duty cycle outputs.
The bandwidth of the ADXL202/ADXL210 may be set from
0.01 Hz to 5 kHz via capacitors C
X
and C
Y
. The typical noise
floor is 500 µg/√Hz allowing signals below 5 mg to be resolved
for bandwidths below 60 Hz.
The ADXL202/ADXL210 is available in a hermetic 14-lead
Surface Mount CERPAK, specified over the 0°C to +70°C
commercial or –40°C to +85°C industrial temperature range.
i
MEM
S
is a registered trademark of Analog Devices, Inc.
ADXL202/ADXL210–SPECIFICATIONS
ADXL202/JQC/AQC ADXL210/JQC/AQC
Parameter Conditions Min Typ Max Min Typ Max Units
SENSOR INPUT Each Axis
Measurement Range
1
±1.5 ±2±8±10 g
Nonlinearity Best Fit Straight Line 0.2 0.2 % of FS
Alignment Error
2
±1±1 Degrees
Alignment Error X Sensor to Y Sensor ±0.01 ±0.01 Degrees
Transverse Sensitivity
3
±2±2%
SENSITIVITY Each Axis
Duty Cycle per g T1/T2 @ +25°C 10 12.5 15 3.2 4.0 4.8 %/g
Sensitivity, Analog Output At Pins X
FILT
, Y
FILT
312 100 mV/g
Temperature Drift
4
∆ from +25°C±0.5 ±0.5 % Rdg
ZERO g BIAS LEVEL Each Axis
0 g Duty Cycle T1/T2 25 50 75 42 50 58 %
Initial Offset ±2±2g
0 g Duty Cycle vs. Supply 1.0 4.0 1.0 4.0 %/V
0 g Offset vs. Temperature
4
∆ from +25°C 2.0 2.0 mg/°C
NOISE PERFORMANCE
Noise Density
5
@ +25°C 500 1000 500 1000 µg/√Hz
FREQUENCY RESPONSE
3 dB Bandwidth Duty Cycle Output 500 500 Hz
3 dB Bandwidth At Pins X
FILT
, Y
FILT
55kHz
Sensor Resonant Frequency 10 14 kHz
FILTER
R
FILT
Tolerance 32 kΩ Nominal ±15 ±15 %
Minimum Capacitance At X
FILT
, Y
FILT
1000 1000 pF
SELF TEST
Duty Cycle Change Self-Test “0” to “1” 10 10 %
DUTY CYCLE OUTPUT STAGE
F
SET
125 MΩ/R
SET
125 MΩ/R
SET
F
SET
Tolerance R
SET
= 125 kΩ0.7 1.3 0.7 1.3 kHz
Output High Voltage I = 25 µAV
S
– 200 mV V
S
– 200 mV mV
Output Low Voltage I = 25 µA 200 200 mV
T2 Drift vs. Temperature 35 35 ppm/°C
Rise/Fall Time 200 200 ns
POWER SUPPLY
Operating Voltage Range 3.0 5.25 2.7 5.25 V
Specified Performance 4.75 5.25 4.75 5.25 V
Quiescent Supply Current 0.6 1.0 0.6 1.0 mA
Turn-On Time
6
To 99% 160 C
FILT
+ 0.3 160 C
FILT
+ 0.3 ms
TEMPERATURE RANGE
Operating Range JQC 0 +70 0 +70 °C
Specified Performance AQC –40 +85 –40 +85 °C
NOTES
1
For all combinations of offset and sensitivity variation.
2
Alignment error is specified as the angle between the true and indicated axis of sensitivity.
3
Transverse sensitivity is the algebraic sum of the alignment and the inherent sensitivity errors.
4
Specification refers to the maximum change in parameter from its initial at +25 °C to its worst case value at T
MIN
to T
MAX
.
5
Noise density (µg/√Hz) is the average noise at any frequency in the bandwidth of the part.
6
C
FILT
in µF. Addition of filter capacitor will increase turn on time. Please see the Application section on power cycling.
All min and max specifications are guaranteed. Typical specifications are not tested or guaranteed.
Specifications subject to change without notice.
(T
A
= T
MIN
to T
MAX
, T
A
= +25ⴗC for J Grade only, V
DD
= +5 V,
R
SET
= 125 k⍀, Acceleration = 0
g
, unless otherwise noted)
REV. B
–2–
ADXL202/ADXL210
–3–REV. B
PIN FUNCTION DESCRIPTIONS
Pin Name Description
1 NC No Connect
2V
TP
Test Point, Do Not Connect
3 ST Self Test
4 COM Common
5 T2 Connect R
SET
to Set T2 Period
6 NC No Connect
7 COM Common
8 NC No Connect
9Y
OUT
Y Axis Duty Cycle Output
10 X
OUT
X Axis Duty Cycle Output
11 Y
FILT
Connect Capacitor for Y Filter
12 X
FILT
Connect Capacitor for X Filter
13 V
DD
+3 V to +5.25 V, Connect to 14
14 V
DD
+3 V to +5.25 V, Connect to 13
PACKAGE CHARACTERISTICS
Package
JA
JC
Device Weight
14-Lead CERPAK 110°C/W 30°C/W 5 Grams
ABSOLUTE MAXIMUM RATINGS*
Acceleration (Any Axis, Unpowered for 0.5 ms) . . . . . . 1000 g
Acceleration (Any Axis, Powered for 0.5 ms) . . . . . . . . . 500 g
+V
S
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7.0 V
Output Short Circuit Duration
(Any Pin to Common) . . . . . . . . . . . . . . . . . . . . . . Indefinite
Operating Temperature . . . . . . . . . . . . . . . . . –55°C to +125°C
Storage Temperature . . . . . . . . . . . . . . . . . . . –65°C to +150°C
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; the functional operation of
the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADXL202/ADXL210 features proprietary ESD protection circuitry, permanent
damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper
ESD precautions are recommended to avoid performance degradation or loss of functionality.
Drops onto hard surfaces can cause shocks of greater than 1000 g
and exceed the absolute maximum rating of the device. Care
should be exercised in handling to avoid damage.
PIN CONFIGURATION
14
13
12
11
10
9
8
1
2
3
4
7
6
5
TOP VIEW
(Not to Scale)
AY
AX
NC = NO CONNECT
NC
YFILT
XFILT
VDD
VDD
VTP
ST
COM
NC
YOUT
XOUT
T2
NC
COM
ADXL202/
ADXL210
Figure 1 shows the response of the ADXL202 to the Earth’s
gravitational field. The output values shown are nominal. They
are presented to show the user what type of response to expect
from each of the output pins due to changes in orientation with
respect to the Earth. The ADXL210 reacts similarly with out-
put changes appropriate to its scale.
TYPICAL OUTPUT AT PIN:
9 = 50% DUTY CYCLE
10 = 62.5% DUTY CYCLE
11 = 2.5V
12 = 2.188V
TYPICAL OUTPUT AT PIN:
9 = 62.5% DUTY CYCLE
10 = 50% DUTY CYCLE
11 = 2.188V
12 = 2.5V
TYPICAL OUTPUT AT PIN:
9 = 37.5% DUTY CYCLE
10 = 50% DUTY CYCLE
11 = 2.812V
12 = 2.5V
TYPICAL OUTPUT AT PIN:
9 = 50% DUTY CYCLE
10 = 37.5% DUTY CYCLE
11 = 2.5V
12 = 2.812V EARTH'S SURFACE
1
g
Figure 1. ADXL202/ADXL210 Nominal Response Due to
Gravity
WARNING!
ESD SENSITIVE DEVICE
ORDERING GUIDE
gTemperature Package Package
Model Range Range Description Option
ADXL202JQC ±20°C to +70°C 14-Lead CERPAK QC-14
ADXL202AQC ±2 –40°C to +85°C 14-Lead CERPAK QC-14
ADXL210JQC ±10 0°C to +70°C 14-Lead CERPAK QC-14
ADXL210AQC ±10 –40°C to +85°C 14-Lead CERPAK QC-14
ADXL202/ADXL210
REV. B
–4–
TEMPERATURE – 8C
1.06
0.94
–45 90–30
PERIOD NORMALIZED TO 1 AT 25 8C
–150 1530456075
1.04
1.02
1.00
0.98
0.96
Figure 2. Normalized DCM Period (T2) vs. Temperature
TEMPERATURE – 8C
0.8
–0.2
–0.8
–40 90–30
ZERO
g
OFFSET SHIFT IN
g
–20–100 1020304050 607080
0.6
0
–0.4
–0.6
0.4
0.2
Figure 3. Typical Zero g Offset vs. Temperature
TEMPERATURE – 8C
0.7
0
–40 100–20
SUPPLY CURRENT – mA
020406080
0.6
0.4
0.3
0.2
0.1
0.5
VS = 5 VDC
VS = 3.5 VDC
Figure 4. Typical Supply Current vs. Temperature
(@ +25ⴗC RSET = 125 k⍀, VDD = +5 V, unless otherwise noted)
TYPICAL CHARACTERISTICS
TEMPERATURE – 8C
4%
3%
–4%
–40 8525
0%
–1%
–2%
–3%
2%
1%
CHANGE IN SENSITIVITY
Figure 5. Typical X Axis Sensitivity Drift Due to
Temperature
0 0.4 0.8 1.2 1.4
FREQUENCY – ms
3
2
1
0
VOLTS
CFILT = 0.01mF
Figure 6. Typical Turn-On Time
g
/DUTY CYCLE OUTPUT
20
6
0–0.87g
PERCENTAGE OF SAMPLES
–0.64g –0.41g –0.17g 0.06g 0.29g 0.52g 0.75g
18
8
4
2
14
10
16
12
Figure 7. Typical Zero g Distribution at +25
°
C
ADXL202/ADXL210
–5–REV. B
DUTY CYCLE OUTPUT – % per
g
11.3 11.5 11.7 11.9 12.2 12.4 12.6 12.8 13.1 13.3 13.5 13.7
9
8
0
PERCENTAGE OF SAMPLES
4
3
2
1
6
5
7
Figure 8. Typical Sensitivity per g at +25
°
C
CX, CY
BANDWIDTH
14
12
0
0.01mF
500Hz 0.47mF
10Hz
0.047mF
100Hz
TOTAL RMS NOISE – m
g
0.1mF
50Hz
8
6
4
2
10
Figure 9. Typical Noise at X
FILT
Output
NUMBER OF AVERAGE SAMPLES
14
12
01644
TOTAL RMS NOISE – m
g
16
8
6
4
2
10 CFILT = 0.047mF
BW = 100Hz
CFILT = 0.1mF
BW = 50Hz
CFILT = 0.47mF
BW = 10Hz
CFILT = 0.01mF
BW = 500Hz T2 = 1ms
Figure 10. Typical Noise at Digital Outputs
DEGREES OF MISALIGNMENT
20
6
0
–1.375
0.375
% OF PARTS
–1.125
–0.875
–0.625
–0.375
–0.0125
18
8
4
2
16
12
14
10
0.625
0.875
1.125
1.375
0.0125
Figure 11. Rotational Die Alignment
ADXL202/ADXL210
REV. B
–6–
DEFINITIONS
T1 Length of the “on” portion of the cycle.
T2 Length of the total cycle.
Duty Cycle Ratio of the “on” time (T1) of the cycle to the total
cycle (T2). Defined as T1/T2 for the ADXL202/
ADXL210.
Pulsewidth Time period of the “on” pulse. Defined as T1 for
the ADXL202/ADXL210.
THEORY OF OPERATION
The ADXL202/ADXL210 are complete dual axis acceleration
measurement systems on a single monolithic IC. They contain a
polysilicon surface-micromachined sensor and signal condition-
ing circuitry to implement an open loop acceleration measure-
ment architecture. For each axis, an output circuit converts the
analog signal to a duty cycle modulated (DCM) digital signal
that can be decoded with a counter/timer port on a micropro-
cessor. The ADXL202/ADXL210 are capable of measuring
both positive and negative accelerations to a maximum level of
±2 g or ±10 g. The accelerometer measures static acceleration
forces such as gravity, allowing it to be used as a tilt sensor.
The sensor is a surface micromachined polysilicon structure
built on top of the silicon wafer. Polysilicon springs suspend the
structure over the surface of the wafer and provide a resistance
against acceleration forces. Deflection of the structure is mea-
sured using a differential capacitor that consists of independent
fixed plates and central plates attached to the moving mass. The
fixed plates are driven by 180° out of phase square waves. An
acceleration will deflect the beam and unbalance the differential
capacitor, resulting in an output square wave whose amplitude
is proportional to acceleration. Phase sensitive demodulation
techniques are then used to rectify the signal and determine the
direction of the acceleration.
The output of the demodulator drives a duty cycle modulator
(DCM) stage through a 32 kΩ resistor. At this point a pin is
available on each channel to allow the user to set the signal
bandwidth of the device by adding a capacitor. This filtering
improves measurement resolution and helps prevent aliasing.
After being low-pass filtered, the analog signal is converted to a
duty cycle modulated signal by the DCM stage. A single resistor
sets the period for a complete cycle (T2), which can be set be-
tween 0.5 ms and 10 ms (see Figure 12). A 0 g acceleration
produces a nominally 50% duty cycle. The acceleration signal
can be determined by measuring the length of the T1 and T2
pulses with a counter/timer or with a polling loop using a low
cost microcontroller.
An analog output voltage can be obtained either by buffering the
signal from the X
FILT
and Y
FILT
pin, or by passing the duty cycle
signal through an RC filter to reconstruct the dc value.
The ADXL202/ADXL210 will operate with supply voltages as
low as 3.0 V or as high as 5.25 V.
A(
g
) = (T1/T2 – 0.5)/12.5%
0
g
= 50% DUTY CYCLE
T2(s) = RSET(V)/125MV
T2
T1
Figure 12. Typical Output Duty Cycle
APPLICATIONS
POWER SUPPLY DECOUPLING
For most applications a single 0.1 µF capacitor, C
DC
, will ad-
equately decouple the accelerometer from signal and noise on
the power supply. However, in some cases, especially where digital
devices such as microcontrollers share the same power supply, digi-
tal noise on the supply may cause interference on the ADXL202/
ADXL210 output. This is often observed as a slowly undulating
fluctuation of voltage at X
FILT
and Y
FILT
. If additional decou-
pling is needed, a 100 Ω (or smaller) resistor or ferrite beads,
may be inserted in the ADXL202/ADXL210’s supply line.
DESIGN PROCEDURE FOR THE ADXL202/ADXL210
The design procedure for using the ADXL202/ADXL210 with a
duty cycle output involves selecting a duty cycle period and a
filter capacitor. A proper design will take into account the appli-
cation requirements for bandwidth, signal resolution and acqui-
sition time, as discussed in the following sections.
V
DD
The ADXL202/ADXL210 have two power supply (V
DD
) Pins:
13 and 14. These two pins should be connected directly together.
COM
The ADXL202/ADXL210 have two commons, Pins 4 and 7.
These two pins should be connected directly together and Pin 7
grounded.
V
TP
This pin is to be left open; make no connections of any kind to
this pin.
Decoupling Capacitor C
DC
A 0.1 µF capacitor is recommended from V
DD
to COM for
power supply decoupling.
ST
The ST pin controls the self-test feature. When this pin is set to
V
DD
, an electrostatic force is exerted on the beam of the acceler-
ometer. The resulting movement of the beam allows the user to
test if the accelerometer is functional. The typical change in
output will be 10% at the duty cycle outputs (corresponding to
800 mg). This pin may be left open circuit or connected to
common in normal use.
Duty Cycle Decoding
The ADXL202/ADXL210’s digital output is a duty cycle modu-
lator. Acceleration is proportional to the ratio T1/T2. The
nominal output of the ADXL202 is:
0 g = 50% Duty Cycle
Scale factor is 12.5% Duty Cycle Change per g
The nominal output of the ADXL210 is:
0 g = 50% Duty Cycle
Scale factor is 4% Duty Cycle Change per g
These nominal values are affected by the initial tolerance of the
device including zero g offset error and sensitivity error.
T2 does not have to be measured for every measurement cycle.
It need only be updated to account for changes due to tempera-
ture, (a relatively slow process). Since the T2 time period is
shared by both X and Y channels, it is necessary only to mea-
sure it on one channel of the ADXL202/ADXL210. Decoding
algorithms for various microcontrollers have been developed.
Consult the appropriate Application Note.
ADXL202/ADXL210
–7–REV. B
Setting the Bandwidth Using C
X
and C
Y
The ADXL202/ADXL210 have provisions for bandlimiting the
X
FILT
and Y
FILT
pins. Capacitors must be added at these pins to
implement low-pass filtering for antialiasing and noise reduc-
tion. The equation for the 3 dB bandwidth is:
F
–3 dB
=1
2
π
(32 kΩ)×C(x,y)
()
or, more simply,
F–3 dB =5µF
C(X,Y)
The tolerance of the internal resistor (R
FILT
), can vary as much
as ±25% of its nominal value of 32 kΩ; so the bandwidth will
vary accordingly. A minimum capacitance of 1000 pF for C
(X, Y)
is required in all cases.
Table I. Filter Capacitor Selection, C
X
and C
Y
Capacitor
Bandwidth Value
10 Hz 0.47 µF
50 Hz 0.10 µF
100 Hz 0.05 µF
200 Hz 0.027 µF
500 Hz 0.01 µF
5 kHz 0.001 µF
Setting the DCM Period with R
SET
The period of the DCM output is set for both channels by a
single resistor from R
SET
to ground. The equation for the period
is:
T2=RSET (Ω)
125 MΩ
A 125 kΩ resistor will set the duty cycle repetition rate to ap-
proximately 1 kHz, or 1 ms. The device is designed to operate at
duty cycle periods between 0.5 ms and 10 ms.
Table II. Resistor Values to Set T2
T2 R
SET
1 ms 125 kΩ
2 ms 250 kΩ
5 ms 625 kΩ
10 ms 1.25 MΩ
Note that the R
SET
should always be included, even if only an
analog output is desired. Use an R
SET
value between 500 kΩ
and 2 MΩ when taking the output from X
FILT
or Y
FILT
. The
R
SET
resistor should be place close to the T2 Pin to minimize
parasitic capacitance at this node.
Selecting the Right Accelerometer
For most tilt sensing applications the ADXL202 is the most
appropriate accelerometer. Its higher sensitivity (12.5%/g allows
the user to use a lower speed counter for PWM decoding while
maintaining high resolution. The ADXL210 should be used in
applications where accelerations of greater than ±2 g are expected.
MICROCOMPUTER INTERFACES
The ADXL202/ADXL210 were specifically designed to work
with low cost microcontrollers. Specific code sets, reference
designs, and application notes are available from the factory.
This section will outline a general design procedure and discuss
the various trade-offs that need to be considered.
The designer should have some idea of the required perfor-
mance of the system in terms of:
Resolution: the smallest signal change that needs to be detected.
Bandwidth: the highest frequency that needs to be detected.
Acquisition Time: the time that will be available to acquire the
signal on each axis.
These requirements will help to determine the accelerometer
bandwidth, the speed of the microcontroller clock and the
length of the T2 period.
When selecting a microcontroller it is helpful to have a counter
timer port available. The microcontroller should have provisions
for software calibration. While the ADXL202/ADXL210 are
highly accurate accelerometers, they have a wide tolerance for
DEMOD
RFILT
32kV
RFILT
32kV
OSCILLATOR
X SENSOR
Y SENSOR
X OUT
Y OUT
SELF TEST
XFILT
VDD
VDD
CX
+3.0V TO +5.25V
CDC
COM YFILT T2
CYRSET
C
O
U
N
T
E
R
mP
T2
A(
g
) = (T1/T2 – 0.5)/12.5%
0
g
= 50% DUTY CYCLE
T2 = RSET/125MV
T1
DEMOD
DUTY
CYCLE
MODULATOR
(DCM)
ADXL202/
ADXL210
Figure 13. Block Diagram
ADXL202/ADXL210
REV. B
–8–
Table IV gives typical noise output of the ADXL202/ADXL210
for various C
X
and C
Y
values.
Table IV. Filter Capacitor Selection, C
X
and C
Y
Peak-to-Peak Noise
Estimate 95%
Bandwidth C
X
, C
Y
rms Noise Probability (rms ⴛ 4)
10 Hz 0.47 µF 1.9 mg7.6 mg
50 Hz 0.10 µF 4.3 mg17.2 mg
100 Hz 0.05 µF 6.1 mg24.4 mg
200 Hz 0.027 µF 8.7 mg35.8 mg
500 Hz 0.01 µF 13.7 mg54.8 mg
CHOOSING T2 AND COUNTER FREQUENCY: DESIGN
TRADE-OFFS
The noise level is one determinant of accelerometer resolution.
The second relates to the measurement resolution of the
counter when decoding the duty cycle output.
The ADXL202/ADXL210’s duty cycle converter has a resolu-
tion of approximately 14 bits; better resolution than the acceler-
ometer itself. The actual resolution of the acceleration signal is,
however, limited by the time resolution of the counting devices
used to decode the duty cycle. The faster the counter clock, the
higher the resolution of the duty cycle and the shorter the T2
period can be for a given resolution. The following table shows
some of the trade-offs. It is important to note that this is the
resolution due to the microprocessors’s counter. It is probable
that the accelerometer’s noise floor may set the lower limit on
the resolution, as discussed in the previous section.
Table V. Trade-Offs Between Microcontroller Counter Rate,
T2 Period and Resolution of Duty Cycle Modulator
ADXL202/ Counter-
ADXL210 Clock Counts
R
SET
Sample Rate per T2 Counts Resolution
T2 (ms) (k⍀) Rate (MHz) Cycle per g(mg)
1.0 124 1000 2.0 2000 250 4.0
1.0 124 1000 1.0 1000 125 8.0
1.0 124 1000 0.5 500 62.5 16.0
5.0 625 200 2.0 10000 1250 0.8
5.0 625 200 1.0 5000 625 1.6
5.0 625 200 0.5 2500 312.5 3.2
10.0 1250 100 2.0 20000 2500 0.4
10.0 1250 100 1.0 10000 1250 0.8
10.0 1250 100 0.5 5000 625 1.6
initial offset. The easiest way to null this offset is with a calibra-
tion factor saved on the microcontroller or by a user calibration
for zero g. In the case where the offset is calibrated during manu-
facture, there are several options, including external EEPROM
and microcontrollers with “one-time programmable” features.
DESIGN TRADE-OFFS FOR SELECTING FILTER
CHARACTERISTICS: THE NOISE/BW TRADE-OFF
The accelerometer bandwidth selected will determine the mea-
surement resolution (smallest detectable acceleration). Filtering
can be used to lower the noise floor and improve the resolution
of the accelerometer. Resolution is dependent on both the ana-
log filter bandwidth at X
FILT
and Y
FILT
and on the speed of the
microcontroller counter.
The analog output of the ADXL202/ADXL210 has a typical
bandwidth of 5 kHz, much higher than the duty cycle stage is
capable of converting. The user must filter the signal at this
point to limit aliasing errors. To minimize DCM errors the
analog bandwidth should be less than 1/10 the DCM frequency.
Analog bandwidth may be increased to up to 1/2 the DCM
frequency in many applications. This will result in greater dy-
namic error generated at the DCM.
The analog bandwidth may be further decreased to reduce noise
and improve resolution. The ADXL202/ADXL210 noise has
the characteristics of white Gaussian noise that contributes
equally at all frequencies and is described in terms of µg per root
Hz; i.e., the noise is proportional to the square root of the band-
width of the accelerometer. It is recommended that the user limit
bandwidth to the lowest frequency needed by the application, to
maximize the resolution and dynamic range of the accelerometer.
With the single pole roll-off characteristic, the typical noise of
the ADXL202/ADXL210 is determined by the following equation:
Noise rms
()
=500 µg/Hz
×BW ×1. 5
At 100 Hz the noise will be:
Noise rms
()
=500 µg/Hz
×100 ×(1. 5 )
=6.12 mg
Often the peak value of the noise is desired. Peak-to-peak noise
can only be estimated by statistical methods. Table III is useful
for estimating the probabilities of exceeding various peak values,
given the rms value.
Table III. Estimation of Peak-to-Peak Noise
% of Time that Noise
Nominal Peak-to-Peak Will Exceed Nominal
Value Peak-to-Peak Value
2.0 × rms 32%
4.0 × rms 4.6%
6.0 × rms 0.27%
8.0 × rms 0.006%
The peak-to-peak noise value will give the best estimate of the
uncertainty in a single measurement.
ADXL202/ADXL210
–9–REV. B
A DUAL AXIS TILT SENSOR: CONVERTING
ACCELERATION TO TILT
When the accelerometer is oriented so both its X and Y axes are
parallel to the earth’s surface it can be used as a two axis tilt
sensor with a roll and a pitch axis. Once the output signal from
the accelerometer has been converted to an acceleration that
varies between –1 g and +1 g, the output tilt in degrees is calcu-
lated as follows:
Pitch = ASIN (Ax/1 g)
Roll = ASIN (Ay/1 g)
Be sure to account for overranges. It is possible for the acceler-
ometers to output a signal greater than ±1 g due to vibration,
shock or other accelerations.
MEASURING 360ⴗ OF TILT
It is possible to measure a full 360° of orientation through grav-
ity by using two accelerometers oriented perpendicular to one
another (see Figure 15). When one sensor is reading a maxi-
mum change in output per degree, the other is at its minimum.
Y
X
3608 OF TILT 1
g
Figure 15. Using a Two-Axis Accelerometer to Measure
360
°
of Tilt
STRATEGIES FOR USING THE DUTY CYCLE OUTPUT
WITH MICROCONTROLLERS
Application notes outlining various strategies for using the duty
cycle output with low cost microcontrollers are available from
the factory.
USING THE ADXL202/ADXL210 AS A DUAL AXIS TILT
SENSOR
One of the most popular applications of the ADXL202/ADXL210
is tilt measurement. An accelerometer uses the force of gravity
as an input vector to determine orientation of an object in space.
An accelerometer is most sensitive to tilt when its sensitive axis
is perpendicular to the force of gravity, i.e., parallel to the
earth’s surface. At this orientation its sensitivity to changes in
tilt is highest. When the accelerometer is oriented on axis to
gravity, i.e., near its +1 g or –1 g reading, the change in output
acceleration per degree of tilt is negligible. When the accelerom-
eter is perpendicular to gravity, its output will change nearly
17.5 mg per degree of tilt, but at 45° degrees it is changing only
at 12.2 mg per degree and resolution declines. The following
table illustrates the changes in the X and Y axes as the device is
tilted ±90° through gravity.
Y
X
+908
08
–908
1
g
X OUTPUT Y OUTPUT (
g
)
X AXIS ⌬ PER ⌬ PER
ORIENTATION DEGREE OF DEGREE OF
TO HORIZON (ⴗ) X OUTPUT (
g
) TILT (m
g
) Y OUTPUT (
g
) TILT (m
g
)
–90 –1.000 –0.2 0.000 17.5
–75 –0.966 4.4 0.259 16.9
–60 –0.866 8.6 0.500 15.2
–45 –0.707 12.2 0.707 12.4
–30 –0.500 15.0 0.866 8.9
–15 –0.259 16.8 0.966 4.7
–0 0.000 17.5 1.000 0.2
–15 0.259 16.9 0.966 –4.4
–30 0.500 15.2 0.866 –8.6
–45 0.707 12.4 0.707 –12.2
–60 0.866 8.9 0.500 –15.0
–75 0.966 4.7 0.259 –16.8
–90 1.000 0.2 0.000 –17.5
Figure 14. How the X and Y Axes Respond to Changes in
Tilt
ADXL202/ADXL210
REV. B
–10–
USING THE ANALOG OUTPUT
The ADXL202/ADXL210 was specifically designed for use with
its digital outputs, but has provisions to provide analog outputs
as well.
Duty Cycle Filtering
An analog output can be reconstructed by filtering the duty
cycle output. This technique requires only passive components.
The duty cycle period (T2) should be set to 1 ms. An RC filter
with a 3 dB point at least a factor of 10 less than the duty cycle
frequency is connected to the duty cycle output. The filter resis-
tor should be no less than 100 kΩ to prevent loading of the
output stage. The analog output signal will be ratiometric to the
supply voltage. The advantage of this method is an output scale
factor of approximately double the analog output. Its disadvan-
tage is that the frequency response will be lower than when
using the X
FILT
, Y
FILT
output.
X
FILT
, Y
FILT
Output
The second method is to use the analog output present at the
X
FILT
and Y
FILT
pin. Unfortunately, these pins have a 32 kΩ
output impedance and are not designed to drive a load directly.
An op amp follower may be required to buffer this pin. The
advantage of this method is that the full 5 kHz bandwidth of the
accelerometer is available to the user. A capacitor still must be
added at this point for filtering. The duty cycle converter should
be kept running by using R
SET
<10 MΩ. Note that the acceler-
ometer offset and sensitivity are ratiometric to the supply volt-
age. The offset and sensitivity are nominally:
0 g Offset = V
DD
/2 2.5 V at +5 V
ADXL202 Sensitivity = (60 mV × V
S
)/g300 mV/g at +5 V, V
DD
ADXL210 Sensitivity = (20 mV × V
S
)/g100 mV/g at +5 V, V
DD
USING THE ADXL202/ADXL210 IN VERY LOW POWER
APPLICATIONS
An application note outlining low power strategies for the
ADXL202/ADXL210 is available. Some key points are pre-
sented here. It is possible to reduce the ADXL202/ADXL210’s
average current from 0.6 mA to less than 20 µA by using the
following techniques:
1. Power Cycle the accelerometer.
2. Run the accelerometer at a Lower Voltage, (Down to 3 V).
Power Cycling with an External A/D
Depending on the value of the X
FILT
capacitor, the ADXL202/
ADXL210 is capable of turning on and giving a good reading in
1.6 ms. Most microcontroller based A/Ds can acquire a reading
in another 25 µs. Thus it is possible to turn on the ADXL202/
ADXL210 and take a reading in <2 ms. If we assume that a
20 Hz sample rate is sufficient, the total current required to
take 20 samples is 2 ms × 20 samples/s × 0.6 mA = 24 µA aver-
age current. Running the part at 3 V will reduce the supply
current from 0.6 mA to 0.4 mA, bringing the average current
down to 16 µA.
The A/D should read the analog output of the ADXL202/
ADXL210 at the X
FILT
and Y
FILT
pins. A buffer amplifier is
recommended, and may be required in any case to amplify the
analog output to give enough resolution with an 8-bit to 10-bit
converter.
Power Cycling When Using the Digital Output
An alternative is to run the microcontroller at a higher clock
rate and put it into shutdown between readings, allowing the
use of the digital output. In this approach the ADXL202/
ADXL210 should be set at its fastest sample rate (T2 = 0.5 ms),
with a 500 Hz filter at X
FILT
and Y
FILT
. The concept is to ac-
quire a reading as quickly as possible and then shut down the
ADXL202/ADXL210 and the microcontroller until the next
sample is needed.
In either of the above approaches, the ADXL202/ADXL210
can be turned on and off directly using a digital port pin on the
microcontroller to power the accelerometer without additional
components. The port should be used to switch the common
pin of the accelerometer so the port pin is “pulling down.”
CALIBRATING THE ADXL202/ADXL210
The initial value of the offset and scale factor for the ADXL202/
ADXL210 will require calibration for applications such as tilt
measurement. The ADXL202/ADXL210 architecture has been
designed so that these calibrations take place in the software of
the microcontroller used to decode the duty cycle signal. Cali-
bration factors can be stored in EEPROM or determined at
turn-on and saved in dynamic memory.
For low g applications, the force of gravity is the most stable,
accurate and convenient acceleration reference available. A
reading of the 0 g point can be determined by orientating the
device parallel to the earth’s surface and then reading the output.
A more accurate calibration method is to make a measurements
at +1 g and –1 g. The sensitivity can be determined by the two
measurements.
To calibrate, the accelerometer’s measurement axis is pointed
directly at the earth. The 1 g reading is saved and the sensor is
turned 180° to measure –1 g. Using the two readings, the sensi-
tivity is:
Let A = Accelerometer output with axis oriented to +1 g
Let B = Accelerometer output with axis oriented to –1 g then:
Sensitivity = [A – B]/2 g
For example, if the +1 g reading (A) is 55% duty cycle and the
–1 g reading (B) is 32% duty cycle, then:
Sensitivity = [55% – 32%]/2 g = 11.5%/g
These equations apply whether the output is analog, or duty
cycle.
Application notes outlining algorithms for calculating accelera-
tion from duty cycle and automated calibration routines are
available from the factory.
ADXL202/ADXL210
–11–REV. B
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
14-Lead CERPAK
(QC-14)
0.291 (7.391)
0.285 (7.239)
0.390 (9.906)
MAX
PIN 1
0.419 (10.643)
0.394 (10.008)
7
14 8
1
0.300 (7.62)
0.345 (8.763)
0.290 (7.366)
0.0125 (0.318)
0.009 (0.229) 0.050 (1.270)
0.016 (0.406)
8°
0°
SEATING
PLANE
0.020 (0.508)
0.004 (0.102)
0.020 (0.508)
0.013 (0.330)
0.050
(1.27)
BSC
0.195 (4.953)
0.115 (2.921)
0.215 (5.461)
0.119 (3.023)
C3037b–2–4/99
PRINTED IN U.S.A.
