LTC6409 10GHz GBW, 1.1nV/Hz Differential Amplifier/ADC Driver FEATURES n n n n n n n n n n n n DESCRIPTION 10GHz Gain-Bandwidth Product 88dB SFDR at 100MHz, 2VP-P 1.1nV/Hz Input Noise Density Input Range Includes Ground External Resistors Set Gain (Min 1V/V) 3300V/s Differential Slew Rate 52mA Supply Current 2.7V to 5.25V Supply Voltage Range Fully Differential Input and Output Adjustable Output Common Mode Voltage Low Power Shutdown Small 10-Lead 3mm x 2mm x 0.75mm QFN Package The LTC(R)6409 is a very high speed, low distortion, differential amplifier. Its input common mode range includes ground, so that a ground-referenced input signal can be DC-coupled, level-shifted, and converted to drive an ADC differentially. The gain and feedback resistors are external, so that the exact gain and frequency response can be tailored to each application. For example, the amplifier could be externally compensated in a no-overshoot configuration, which is desired in certain time-domain applications. The LTC6409 is stable in a differential gain of 1. This allows for a low output noise in applications where gain is not desired. It draws 52mA of supply current and has a hardware shutdown feature which reduces current consumption to 100A. APPLICATIONS n n n n n Differential Pipeline ADC Driver High Speed Data-Acquisition Cards Automated Test Equipment Time Domain Reflectometry Communications Receivers The LTC6409 is available in a compact 3mm x 2mm 10pin leadless QFN package and operates over a -40C to 125C temperature range. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Analog Devices, Inc. All other trademarks are the property of their respective owners. TYPICAL APPLICATION DC-Coupled Interface from a Ground-Referenced Single-Ended Input to an LTC2262-14 ADC LTC6409 Driving LTC2262-14 ADC, fIN = 70MHz, -1dBFS, fS = 150MHz, 4096-Point FFT 1.3pF VIN 150 150 1.8V - + VOCM = 0.9V LTC6409 + - 33.2 10 33.2 10 39pF 150 AIN+ VDD LTC2262-14 ADC AIN- GND AMPLITUDE (dBFS) 39pF 3.3V 0 VS = 3.3V -10 V OUTDIFF = 1.8VP-P -20 HD2 = -86.5dBc HD3 = -89.4dBc -30 SFDR = 81.6dB -40 SNR = 71.1dB -50 -60 -70 -80 -90 -100 150 6409 TA01 1.3pF -110 -120 0 10 20 30 40 50 FREQUENCY (MHz) 60 70 6409 TA01b 6409fb For more information www.linear.com/LTC6409 1 LTC6409 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Note 1) ORDER INFORMATION 2 V+ V- 9 8 11,V- 3 4 5 VOCM +IN 10 V+ 1 SHDN -OUT V- TOP VIEW Total Supply Voltage (V+ - V-)..................................5.5V Input Current (+IN, -IN, VOCM, SHDN) (Note 2)................................................................. 10mA Output Short-Circuit Duration (Note 3)............. Indefinite Operating Temperature Range (Note 4)................................................... -40C to 125C Specified Temperature Range (Note 5)................................................... -40C to 125C Maximum Junction Temperature........................... 150C Storage Temperature Range................... -65C to 150C 7 +OUT 6 -IN UDB PACKAGE 10-LEAD (3mm x 2mm) PLASTIC QFN TJMAX = 150C, JA = 138C/W, JC = 5.2C/W EXPOSED PAD (PIN 11) CONNECTED TO V- http://www.linear.com/product/LTC6409#orderinfo Lead Free Finish TAPE AND REEL (MINI) TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION SPECIFIED TEMPERATURE RANGE LTC6409CUDB#TRMPBF LTC6409CUDB#TRPBF LFPF 10-Lead (3mm x 2mm) Plastic QFN 0C to 70C LTC6409IUDB#TRMPBF LTC6409IUDB#TRPBF LFPF 10-Lead (3mm x 2mm) Plastic QFN -40C to 85C LTC6409HUDB#TRMPBF LTC6409HUDB#TRPBF LFPF 10-Lead (3mm x 2mm) Plastic QFN -40C to 125C TRM = 500 pieces. *Temperature grades are identified by a label on the shipping container. Consult LTC Marketing for parts specified with wider operating temperature ranges. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix. ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. V+ = 5V, V- = 0V, VCM = VOCM = VICM = 1.25V, VSHDN = open. VS is defined as (V+ - V-). VOUTCM is defined as (V+OUT + V-OUT)/2. VICM is defined as (V+IN + V-IN)/2. VOUTDIFF is defined as (V+OUT - V-OUT). SYMBOL PARAMETER VOSDIFF CONDITIONS Differential Offset Voltage (Input Referred) VS = 3V VS = 3V VS = 5V VS = 5V VOSDIFF Differential Offset Voltage Drift (Input Referred) T MIN TYP MAX UNITS 300 1000 1200 1100 1400 V V V V l 300 l VS = 3V VS = 5V l l 2 2 IB Input Bias Current (Note 6) VS = 3V VS = 5V l l IOS Input Offset Current (Note 6) VS = 3V VS = 5V l l RIN Input Resistance Common Mode Differential Mode 165 860 CIN Input Capacitance Differential Mode 0.5 pF en Differential Input Noise Voltage Density f = 1MHz, Not Including RI/RF Noise 1.1 nV/Hz in Input Noise Current Density f = 1MHz, Not Including RI/RF Noise 8.8 pA/Hz NF Noise Figure at 100MHz Shunt-Terminated to 50, RS = 50, RI = 25, RF = 10k 6.9 dB 2 -140 -160 V/C V/C -62 -70 0 0 A A 2 2 10 10 A A k 6409fb For more information www.linear.com/LTC6409 LTC6409 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. V+ = 5V, V- = 0V, VCM = VOCM = VICM = 1.25V, VSHDN = open. VS is defined as (V+ - V-). VOUTCM is defined as (V+OUT + V-OUT)/2. VICM is defined as (V+IN + V-IN)/2. VOUTDIFF is defined as (V+OUT - V-OUT). SYMBOL PARAMETER CONDITIONS MIN TYP MAX enVOCM Common Mode Noise Voltage Density f = 10MHz VICMR (Note 7) Input Signal Common Mode Range VS = 3V VS = 5V l l 0 0 CMRRI (Note 8) Input Common Mode Rejection Ratio (Input Referred) VICM/VOSDIFF VS = 3V, VICM from 0V to 1.5V VS = 5V, VICM from 0V to 3.5V l l 75 75 90 90 dB dB VS = 3V, VOCM from 0.5V to 1.5V VS = 5V, VOCM from 0.5V to 3.5V l l 55 60 80 85 dB dB VS = 2.7V to 5.25V l 60 85 dB VS = 2.7V to 5.25V l 55 70 dB l 2.7 CMRRIO Output Common Mode Rejection Ratio (Input (Note 8) Referred) VOCM/VOSDIFF PSRR (Note 9) Differential Power Supply Rejection (VS/VOSDIFF) PSRRCM Output Common Mode Power Supply Rejection (Note 9) (VS/VOSCM) Supply Voltage Range (Note 10) VS 12 UNITS nV/Hz 1.5 3.5 5.25 V V V GCM Common Mode Gain (VOUTCM/VOCM) VS = 3V, VOCM from 0.5V to 1.5V VS = 5V, VOCM from 0.5V to 3.5V l l 1 1 GCM Common Mode Gain Error, 100 x (GCM - 1) VS = 3V, VOCM from 0.5V to 1.5V VS = 5V, VOCM from 0.5V to 3.5V l l 0.1 0.1 0.3 0.3 % % BAL Output Balance (VOUTCM/ VOUTDIFF) VOUTDIFF = 2V Single-Ended Input Differential Input l l -65 -70 -50 -50 dB dB VOSCM Common Mode Offset Voltage (VOUTCM - VOCM) VS = 3V VS = 5V l l 1 1 5 6 mV mV VOSCM T Common Mode Offset Voltage Drift l 4 VS = 3V VS = 5V VOUTCMR Output Signal Common Mode Range (Note 7) (Voltage Range for the VOCM Pin) RINVOCM Input Resistance, VOCM Pin 0.5 0.5 l 30 V V 40 50 k 1.6 V V l 0.9 0.85 1.25 Output Voltage, High, Either Output Pin VS = 3V, IL = 0 VS = 3V, IL = -20mA VS = 5V, IL = 0 VS = 5V, IL = -20mA l l l l 1.85 1.8 3.85 3.8 2 1.95 4 3.95 Output Voltage, Low, Either Output Pin VS = 3V, 5V; IL = 0 VS = 3V, 5V; IL = 20mA l l ISC Output Short-Circuit Current, Either Output Pin (Note 11) VS = 3V VS = 5V l l AVOL Large-Signal Open Loop Voltage Gain IS Supply Current VOUT 0.06 0.2 50 70 V/C 1.5 3.5 VS = 3V, VOCM = Open VS = 5V, VOCM = Open VOCM Self-Biased Voltage at the VOCM Pin l l V/V V/V V V V V 0.15 0.4 V V 70 95 mA mA 65 dB 52 l 56 58 mA mA ISHDN Supply Current in Shutdown VSHDN 0.6V l RSHDN SHDN Pull-Up Resistor VSHDN = 0V to 0.5V l VIL SHDN Input Logic Low l VIH SHDN Input Logic High l tON Turn-On Time 160 ns tOFF Turn-Off Time 80 ns 115 100 500 A 150 185 k 0.6 V 1.4 V 6409fb For more information www.linear.com/LTC6409 3 LTC6409 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. V+ = 5V, V- = 0V, VCM = VOCM = VICM = 1.25V, VSHDN = open. VS is defined as (V+ - V-). VOUTCM is defined as (V+OUT + V-OUT)/2. VICM is defined as (V+IN + V-IN)/2. VOUTDIFF is defined as (V+OUT - V-OUT). SYMBOL PARAMETER CONDITIONS MIN SR Slew Rate Differential Output, VOUTDIFF = 4VP-P +OUT Rising (-OUT Falling) +OUT Falling (-OUT Rising) GBW Gain-Bandwidth Product RI = 25, RF = 10k, fTEST = 100MHz l 9.5 8 TYP MAX UNITS 3300 1720 1580 V/s V/s V/s 10 GHz GHz f-3dB -3dB Frequency RI = RF = 150, RLOAD = 400, CF = 1.3pF 2 GHz f0.1dB Frequency for 0.1dB Flatness RI = RF = 150, RLOAD = 400 , CF = 1.3pF 600 MHz FPBW Full Power Bandwidth VOUTDIFF = 2VP-P 550 MHz HD2 HD3 25MHz Distortion Differential Input, VOUTDIFF = 2VP-P, RI = RF = 150, RLOAD = 400 2nd Harmonic 3rd Harmonic -104 -106 dBc dBc Differential Input, VOUTDIFF = 2VP-P, RI = RF = 150, RLOAD = 400 2nd Harmonic 3rd Harmonic -93 -88 dBc dBc Single-Ended Input, VOUTDIFF = 2VP-P, RI = RF = 150, RLOAD = 400 2nd Harmonic 3rd Harmonic -101 -103 dBc dBc Single-Ended Input, VOUTDIFF = 2VP-P, RI = RF = 150, RLOAD = 400 2nd Harmonic 3rd Harmonic -88 -93 dBc dBc 100MHz Distortion HD2 HD3 25MHz Distortion 100MHz Distortion IMD3 3rd Order IMD at 25MHz f1 = 24.9MHz, f2 = 25.1MHz VOUTDIFF = 2VP-P Envelope, RI = RF = 150, RLOAD = 400 -110 dBc 3rd Order IMD at 100MHz f1 = 99.9MHz, f2 = 100.1MHz VOUTDIFF = 2VP-P Envelope, RI = RF = 150, RLOAD = 400 -98 dBc 3rd Order IMD at 140MHz f1 = 139.9MHz, f2 = 140.1MHz VOUTDIFF = 2VP-P Envelope, RI = RF = 150, RLOAD = 400 -88 dBc 59 53 48 dBm dBm dBm 1.9 ns OIP3 Equivalent OIP3 at 25MHz (Note 12) Equivalent OIP3 at 100MHz (Note 12) Equivalent OIP3 at 140MHz (Note 12) tS Settling Time VOUTDIFF = 2VP-P Step, RI = RF = 150, RLOAD = 400 1% Settling Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: Input pins (+IN, -IN, VOCM, and SHDN) are protected by steering diodes to either supply. If the inputs should exceed either supply voltage, the input current should be limited to less than 10mA. In addition, the inputs +IN, -IN are protected by a pair of back-to-back diodes. If the differential input voltage exceeds 1.4V, the input current should be limited to less than 10mA. Note 3: A heat sink may be required to keep the junction temperature below the absolute maximum rating when the output is shorted indefinitely. 4 Note 4: The LTC6409C/LTC6409I are guaranteed functional over the temperature range of -40C to 85C. The LTC6409H is guaranteed functional over the temperature range of -40C to 125C. Note 5: The LTC6409C is guaranteed to meet specified performance from 0C to 70C. The LTC6409C is designed, characterized and expected to meet specified performance from -40C to 85C, but is not tested or QA sampled at these temperatures. The LTC6409I is guaranteed to meet specified performance from -40C to 85C. The LTC6409H is guaranteed to meet specified performance from -40C to 125C. Note 6: Input bias current is defined as the average of the input currents flowing into the inputs (-IN and +IN). Input offset current is defined as the difference between the input currents (IOS = IB+ - IB-). 6409fb For more information www.linear.com/LTC6409 LTC6409 ELECTRICAL CHARACTERISTICS Note 7: Input common mode range is tested by testing at both VICM = 1.25V and at the Electrical Characteristics table limits to verify that the differential offset (VOSDIFF) and the common mode offset (VOSCM) have not deviated by more than 1mV and 2mV respectively from the VICM = 1.25V case. The voltage range for the output common mode range is tested by applying a voltage on the VOCM pin and testing at both VOCM = 1.25V and at the Electrical Characteristics table limits to verify that the common mode offset (VOSCM) has not deviated by more than 6mV from the VOCM = 1.25V case. Note 8: Input CMRR is defined as the ratio of the change in the input common mode voltage at the pins +IN or -IN to the change in differential input referred offset voltage. Output CMRR is defined as the ratio of the change in the voltage at the VOCM pin to the change in differential input referred offset voltage. This specification is strongly dependent on feedback ratio matching between the two outputs and their respective inputs and it is difficult to measure actual amplifier performance (See Effects of Resistor Pair Mismatch in the Applications Information section of this data sheet). For a better indicator of actual amplifier performance independent of feedback component matching, refer to the PSRR specification. Note 9: Differential power supply rejection (PSRR) is defined as the ratio of the change in supply voltage to the change in differential input referred offset voltage. Common mode power supply rejection (PSRRCM) is defined as the ratio of the change in supply voltage to the change in the output common mode offset voltage. Note 10: Supply voltage range is guaranteed by power supply rejection ratio test. Note 11: Extended operation with the output shorted may cause the junction temperature to exceed the 150C limit. Note 12: Refer to Relationship Between Different Linearity Metrics in the Applications Information section of this data sheet for information on how to calculate an equivalent OIP3 from IMD3 measurements. TYPICAL PERFORMANCE CHARACTERISTICS Differential Input Offset Voltage vs Temperature Differential Input Offset Voltage vs Input Common Mode Voltage 2.0 0.5 0 TA = 85C TA = 70C TA = 25C TA = 0C TA = -40C -0.5 -0.5 -50 -25 0 25 75 50 TEMPERATURE (C) 100 125 -1.0 35 30 20 15 10 5 0 TA = 125C TA = 85C TA = 70C TA = 25C TA = 0C TA = -40C 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 SUPPLY VOLTAGE (V) 6409 G04 TOTAL SUPPLY CURRENT (mA) TOTAL SUPPLY CURRENT (mA) 40 1.0 0.5 0 -0.5 -50 4 140 50 45 40 35 30 25 TA = 125C TA = 85C TA = 70C TA = 25C TA = 0C TA = -40C 20 15 10 5 0 0 0.5 1 1.5 2 2.5 3 3.5 SHDN VOLTAGE (V) 4 4.5 -25 0 25 75 50 TEMPERATURE (C) 100 125 6409 G03 Shutdown Supply Current vs Supply Voltage VS = 5V 55 VS = 5V VOCM = VICM = 1.25V RI = RF = 150 FIVE REPRESENTATIVE UNITS 1.5 Supply Current vs SHDN Voltage 60 45 0.5 1 1.5 2 2.5 3 3.5 INPUT COMMON MODE VOLTAGE (V) 2.0 6409 G02 VSHDN = OPEN 50 25 0 6409 G01 Supply Current vs Supply Voltage 55 COMMON MODE OFFSET VOLTAGE (mV) 0.5 VS = 5V VOCM = VICM = 1.25V RI = RF = 150 FIVE REPRESENTATIVE UNITS 0 SHUTDOWN SUPPLY CURRENT (A) 1.0 2.5 VS = 5V VOCM = 1.25V 1.5 RI = RF = 150 0.1% FEEDBACK NETWORK RESISTORS REPRESENTATIVE UNIT 1.0 DIFFERENTIAL VOS (mV) DIFFERENTIAL VOS (mV) 1.5 60 Common Mode Offset Voltage vs Temperature 5 6409 G05 120 100 TA = 125C TA = 85C TA = 70C TA = 25C TA = 0C TA = -40C 80 60 40 20 0 VSHDN = V- 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 SUPPLY VOLTAGE (V) 6409 G06 6409fb For more information www.linear.com/LTC6409 5 LTC6409 TYPICAL PERFORMANCE CHARACTERISTICS Differential Output Voltage Noise vs Frequency 10 1 1 1k 1M FREQUENCY (Hz) 100 100 in 10 10 en 1 1G 1 1 1G 1k 1M FREQUENCY (Hz) 6409 G07 CMRR vs Frequency 1000 1000 VS = 5V OUTPUT IMPEDANCE () 100 1000 INPUT VOLTAGE NOISE DENSITY (nV/Hz) VS = 5V RI = RF = 150 INCLUDES RI/RF NOISE INPUT CURRENT NOISE DENSITY (pA/Hz) VOLTAGE NOISE DENSITY (nV/Hz) 1000 Differential Output Impedance vs Frequency Input Noise Density vs Frequency VS = 5V RI = RF = 150 100 10 1 0.1 0.01 1 100 1000 FREQUENCY (MHz) 6409 G18 Differential PSRR vs Frequency 100 10 10000 6409 G09 Small Signal Step Response 90 80 -OUT 70 80 PSRR (dB) CMRR (dB) 90 70 VS = 5V 60 VOCM = 1.25V RI = RF = 150, CF = 1.3pF 0.1% FEEDBACK NETWORK RESISTORS 50 1 10 100 1000 FREQUENCY (MHz) 60 20mV/DIV 50 40 +OUT VS = 5V VOCM = VICM = 1.25V RLOAD = 400 30 RI = RF = 150, CF = 1.3pF CL = 0pF VIN = 200mVP-P, DIFFERENTIAL 20 10000 10 VS = 5V 1 6409 G10 10 100 1000 FREQUENCY (MHz) 10000 2ns/DIV 6409 G12 6409 G11 Overdriven Output Transient Response Large Signal Step Response 4.0 3.5 -OUT -OUT VOLTAGE (V) 3.0 0.2V/DIV +OUT 6 2.0 1.5 VS = 5V VOCM = 1.25V RLOAD = 200 TO GROUND PER OUTPUT 1.0 VS = 5V RLOAD = 400 VIN = 2VP-P, DIFFERENTIAL 2ns/DIV 2.5 0.5 6409 G13 0 +OUT 20ns/DIV 6409 G14 6409fb For more information www.linear.com/LTC6409 LTC6409 TYPICAL PERFORMANCE CHARACTERISTICS Frequency Response vs Closed Loop Gain 50 40 GAIN (dB) 30 20 10 0 20 AV = 400 AV = 100 AV (V/V) RI () 1 2 5 10 20 100 400 AV = 20 AV = 10 AV = 5 AV = 2 AV = 1 -10 VS = 5V -20 VOCM = VICM = 1.25V RLOAD = 400 -30 1 10 100 1000 FREQUENCY (MHz) 150 100 50 50 25 25 25 10000 6409 G15 Gain 0.1dB Flatness 3400 0.4 3375 0.3 SLEW RATE (V/s) 0 -0.1 VS = 5V VOCM = VICM = 1.25V -0.4 RLOAD = 400 RI = RF = 150, CF = 1.3pF -0.5 1 10 100 1000 FREQUENCY (MHz) HD3 -25 -60 -100 1000 6409 G19 -110 0.5 125 6409 G08 -80 VS = 5V fIN = 100MHz RLOAD = 400 RI = RF = 150 VOUTDIFF = 2VP-P DIFFERENTIAL INPUTS -70 -80 100 Harmonic Distortion vs Input Amplitude HD3 -90 -110 0 25 50 75 TEMPERATURE (C) 6409 G17 -50 -100 3200 -50 10000 -40 -90 3275 3225 -30 DISTORTION (dBc) DISTORTION (dBc) -50 HD2 3300 Harmonic Distortion vs Output Common Mode Voltage Harmonic Distortion vs Frequency -80 3325 3250 -0.3 10 100 FREQUENCY (MHz) 10000 6409 G16 VS = 5V DISTORTION (dBc) GAIN (dB) 0.1 -0.2 1 -10 VS = 5V VOCM = VICM = 1.25V RLOAD = 400 -20 RI = RF = 150, CF = 1.3pF CAPACITOR VALUES ARE FROM EACH OUTPUT TO GROUND. NO SERIES RESISTORS ARE USED. -30 10 100 1000 FREQUENCY (MHz) 3350 0.2 -120 0 Slew Rate vs Temperature 0.5 VS = 5V VOCM = VICM = 1.25V -60 R LOAD = 400 RI = RF = 150 -70 VOUTDIFF = 2VP-P DIFFERENTIAL INPUTS CL = 0pF CL = 0.5pF CL = 1pF CL = 1.5pF CL = 2pF 10 RF () CF (pF) 150 1.3 200 1 250 0.8 500 0.4 500 0.4 2.5k 0 10k 0 GAIN (dB) 60 Frequency Response vs Load Capacitance VS = 5V VOCM = VICM = 1.25V fIN = 100MHz RLOAD = 400 -90 RI = RF = 150 DIFFERENTIAL INPUTS HD3 HD2 -100 -110 HD2 1 1.5 2 2.5 3 3.5 OUTPUT COMMON MODE VOLTAGE (V) 6409 G20 -120 -2 -4 (0.4VP-P) 0 2 4 6 INPUT AMPLITUDE (dBm) 8 10 (2VP-P) 6409 G21 6409fb For more information www.linear.com/LTC6409 7 LTC6409 TYPICAL PERFORMANCE CHARACTERISTICS Harmonic Distortion vs Output VS = 5V VICM = 1.25V VOCM =Voltage Common Mode -40 -50 DISTORTION (dBc) -80 -90 HD2 -100 -60 -70 -80 1 10 100 FREQUENCY (MHz) -120 -2 -4 (0.4VP-P) 1 1.5 2 2.5 3 3.5 OUTPUT COMMON MODE VOLTAGE (V) THIRD ORDER IMD (dBc) -110 0 2 4 6 INPUT AMPLITUDE (dBm) 8 10 (2VP-P) 6409 G24 Intermodulation Distortion vs Input Amplitude -30 -50 -100 RLOAD = 400 RI = RF = 150 SINGLE-ENDED INPUT 6409 G23 Intermodulation Distortion vs Output Common Mode Voltage -90 HD3 -110 6409 G22 VS = 5V VOCM = VICM = 1.25V -60 R LOAD = 400 RI = RF = 150 -70 2 TONES, 200kHz TONE SPACING, 2VP-P COMPOSITE -80 DIFFERENTIAL INPUTS HD2 -100 HD3 -110 0.5 1000 Intermodulation Distortion vs Frequency THIRD ORDER IMD (dBc) HD2 -100 HD3 VS = 5V VOCM = VICM = 1.25V fIN = 100MHz -90 -90 -110 -120 -80 -80 VS = 5V -40 fIN = 100MHz RLOAD = 400 RI = RF = 150 -50 2 TONES, 200kHz TONE SPACING, 2VP-P COMPOSITE -60 DIFFERENTIAL INPUTS THIRD ORDER IMD (dBc) DISTORTION (dBc) VS = 5V VOCM = VICM = 1.25V -60 R LOAD = 400 RI = RF = 150 -70 VOUTDIFF = 2VP-P SINGLE-ENDED INPUT -120 RLOAD = 400 VSR=I =5VRF = 150 = 2VP-P 100MHz fINV=OUTDIFF SINGLE-ENDED = 400 INPUT RLOAD RI = RF = 150 VOUTDIFF = 2VP-P SINGLE-ENDED INPUT -30 -50 Harmonic Distortion vs Input Amplitude DISTORTION (dBc) Harmonic Distortion vs Frequency -70 -80 -90 VS = 5V VOCM = VICM = 1.25V fIN = 100MHz RLOAD = 400 -90 RI = RF = 150 2 TONES, 200kHz TONE SPACING DIFFERENTIAL INPUTS -100 -110 -100 10 100 FREQUENCY (MHz) 1000 -110 0.5 1 1.5 2 2.5 3 3.5 OUTPUT COMMON MODE VOLTAGE (V) 6409 G25 -120 2 (0.8VP-P) 4 6 8 INPUT AMPLITUDE (dBm) 6409 G26 10 (2VP-P) 6409 G27 PIN FUNCTIONS +IN, -IN (Pins 2, 6): Non-Inverting and Inverting Input Pins. SHDN (Pin 3): When SHDN is floating or directly tied to V+, the LTC6409 is in the normal (active) operating mode. When the SHDN pin is connected to V-, the part is disabled and draws approximately 100A of supply current. V+, V- (Pins 4, 9 and Pins 8, 10): Positive and Negative Power Supply Pins. Similar pins should be connected to the same voltage. 8 VOCM (Pin 5): Output Common Mode Reference Voltage. The voltage on this pin sets the output common mode voltage level. If left floating, an internal resistor divider develops a default voltage of 1.25V with a 5V supply. +OUT, -OUT (Pins 7, 1): Differential Output Pins. Exposed Pad (Pin 11): Tie the bottom pad to V-. If split supplies are used, DO NOT tie the pad to ground. 6409fb For more information www.linear.com/LTC6409 LTC6409 BLOCK DIAGRAM 2 1 +IN -OUT V- 3 SHDN V+ V+ + 200k V+ 5 VOCM - 50k V- 4 V+ 10 V- 9 V+ V- V+ V- 6 -IN 7 8 V- +OUT 6409 BD APPLICATIONS INFORMATION Functional Description The LTC6409 is a small outline, wideband, high speed, low noise, and low distortion fully-differential amplifier with accurate output phase balancing. The amplifier is optimized to drive low voltage, single-supply, differential input analog-to-digital converters (ADCs). The LTC6409 input common mode range includes ground, which makes it ideal to DC-couple and convert ground-referenced, single-ended signals into differential signals that are referenced to the user-supplied output common mode voltage. This is ideal for driving these differential ADCs. The balanced differential nature of the amplifier also provides even-order harmonic distortion cancellation, and low susceptibility to common mode noise (like power supply noise). The LTC6409 can operate with a single-ended input and differential output, or with a differential input and differential output. The outputs of the LTC6409 are capable of swinging from close-to-ground to 1V below V+. They can source or sink up to approximately 70mA of current. Load capacitances should be decoupled with at least 10 of series resistance from each output. Input Pin Protection The LTC6409 input stage is protected against differential input voltages which exceed 1.4V by two pairs of series diodes connected back to back between +IN and -IN. Moreover, the input pins, as well as VOCM and SHDN pins, have clamping diodes to either power supply. If these pins are driven to voltages which exceed either supply, the current should be limited to 10mA to prevent damage to the IC. SHDN Pin The SHDN pin is a CMOS logic input with a 150k internal pull-up resistor. If the pin is driven low, the LTC6409 powers down. If the pin is left unconnected or driven high, the part is in normal active operation. Some care should be taken to control leakage currents at this pin to prevent inadvertently putting the LTC6409 into shutdown. The turn-on and turn-off time between the shutdown and active states is typically less than 200ns. General Amplifier Applications In Figure 1, the gain to VOUTDIFF from VINP and VINM is given by: VOUTDIFF = V+OUT - V-OUT RF * ( VINP - VINM ) RI (1) Note from Equation (1), the differential output voltage (V+OUT - V-OUT) is completely independent of input and output common mode voltages, or the voltage at the common mode pin. This makes the LTC6409 ideally suited for pre-amplification, level shifting and conversion of 6409fb For more information www.linear.com/LTC6409 9 LTC6409 APPLICATIONS INFORMATION RI V+IN RF V-OUT + VINP - + VCM - + VVOCM VOCM - VICM = - VINM + RI V-IN RF 6409 F01 V+OUT Figure 1. Circuit for Common Mode Range single-ended signals to differential output signals for driving differential input ADCs. Output Common Mode and VOCM Pin The output common mode voltage is defined as the average of the two outputs: VOUTCM = VOCM = that can be processed is even wider. The input common mode range at the op amp inputs depends on the circuit configuration (gain), VOCM and VCM (refer to Figure 1). For fully differential input applications, where VINP = -VINM, the common mode input is approximately: V+OUT + V-OUT 2 As the equation shows, the output common mode voltage is independent of the input common mode voltage, and is instead determined by the voltage on the VOCM pin, by means of an internal common mode feedback loop. If the VOCM pin is left open, an internal resistor divider develops a default voltage of 1.25V with a 5V supply. The VOCM pin can be overdriven to another voltage if desired. For example, when driving an ADC, if the ADC makes a reference available for setting the common mode voltage, it can be directly tied to the VOCM pin, as long as the ADC is capable of driving the 40k input resistance presented by the VOCM pin. The Electrical Characteristics table specifies the valid range that can be applied to the VOCM pin (VOUTCMR). V+IN + V-IN RI RF VOCM * + VCM * 2 RI + RF RI + RF With single-ended inputs, there is an input signal component to the input common mode voltage. Applying only VINP (setting VINM to zero), the input common mode voltage is approximately: V+IN + V-IN RI VOCM * + 2 RI + RF RF V RF VCM * + INP * RI + RF 2 RI + RF VICM = This means that if, for example, the input signal (VINP) is a sine, an attenuated version of that sine signal also appears at the op amp inputs. Input Impedance and Loading Effects The low frequency input impedance looking into the VINP or VINM input of Figure 1 depends on how the inputs are driven. For fully differential input sources (VINP = -VINM), the input impedance seen at either input is simply: RINP = RINM = RI For single-ended inputs, because of the signal imbalance at the input, the input impedance actually increases over the balanced differential case. The input impedance looking into either input is: RINP = RINM = Input Common Mode Voltage Range The LTC6409's input common mode voltage (VICM) is defined as the average of the two input pins, V+IN and V-IN. The valid range that can be used for VICM has been specified in the Electrical Characteristics table (VICMR). However, due to external resistive divider action of the gain and feedback resistors, the effective range of signals 10 (2) RI 1- 1 RF * 2 RI + RF Input signal sources with non-zero output impedances can also cause feedback imbalance between the pair of feedback networks. For the best performance, it is recommended that the input source output impedance be compensated. If input impedance matching is required 6409fb For more information www.linear.com/LTC6409 LTC6409 APPLICATIONS INFORMATION by the source, a termination resistor RT should be chosen (see Figure 2) such that: RI2 VINP VOCM - VINM + RI1 V-IN RF1 6409 F03 V+OUT Figure 3. Real-World Application with Feedback Resistor Pair Mismatch R T * RS R T + RS b is defined as the difference in the feedback factors: RINM RI b = RF RT RT CHOSEN SO THAT RT || RINM = RS R2 CHOSEN TO BALANCE RT || RS V-OUT + - According to Figure 2, the input impedance looking into the differential amp (RINM) reflects the single-ended source case, given above. Also, R2 is chosen as: VS - VVOCM RS RF2 + R *R R T = INM S RINM - RS R2 = R T || RS = V+IN RI - + + - RI2 RI1 - RI2 + RF2 RI1 + RF1 Here, VCM and VINDIFF are defined as the average and the difference of the two input voltages VINP and VINM, respectively: RF 6409 F02 R2 = RS || RT VCM = VINP + VINM 2 VINDIFF = VINP - VINM Figure 2. Optimal Compensation for Signal Source Impedance Effects of Resistor Pair Mismatch Figure 3 shows a circuit diagram which takes into consideration that real world resistors will not match perfectly. Assuming infinite open loop gain, the differential output relationship is given by the equation: VOUTDIFF = V+OUT - V-OUT VINDIFF * VCM * RF + RI b b - VOCM * b AVG b AVG where RF is the average of RF1, and RF2, and RI is the average of RI1, and RI2. bAVG is defined as the average feedback factor from the outputs to their respective inputs: b AVG = 1 RI1 RI2 * + 2 RI1 + RF1 RI2 + RF2 When the feedback ratios mismatch (b), common mode to differential conversion occurs. Setting the differential input to zero (VINDIFF = 0), the degree of common mode to differential conversion is given by the equation: VOUTDIFF = V+OUT - V-OUT (VCM - VOCM ) * b (3) b AVG In general, the degree of feedback pair mismatch is a source of common mode to differential conversion of both signals and noise. Using 0.1% resistors or better will mitigate most problems and will provide about 54dB worst case of common mode rejection. A low impedance ground plane should be used as a reference for both the input signal source and the VOCM pin. There may be concern on how feedback factor mismatch affects distortion. Feedback factor mismatch from using 1% resistors or better, has a negligible effect on distortion. However, in single supply level shifting applications where there is a voltage difference between the input common mode voltage and the output common mode voltage, 6409fb For more information www.linear.com/LTC6409 11 LTC6409 APPLICATIONS INFORMATION resistor mismatch can make the apparent voltage offset of the amplifier appear worse than specified. enRI2 RI RF in+2 The apparent input referred offset induced by feedback factor mismatch is derived from Equation (3): VOSDIFF(APPARENT) (VCM - VOCM) * + Using the LTC6409 in a single 5V supply application with 0.1% resistors, the input common mode grounded, and the VOCM pin biased at 1.25V, the worst case mismatch can induce 1.25mV of apparent offset voltage. - in-2 enRI2 If the circuits surrounding the amplifier are well balanced, common mode noise (enVOCM) of the amplifier does not appear in the differential output noise equation given above. A plot of this equation and a plot of the noise generated by the feedback components for the LTC6409 are shown in Figure 5. The LTC6409's input referred voltage noise contributes the equivalent noise of a 75 resistor. When the feedback network is comprised of resistors whose values are larger than this, the output noise is resistor noise and amplifier current noise dominant. For feedback networks consisting of resistors with values smaller than 75, the output noise is voltage noise dominant (see Figure 5). 12 eni2 RI RF enRF2 6409 F04 Figure 4. Simplified Noise Model 1000 NOISE DENSITY (nV/Hz) eno 2 e * 1+ RF + 2 * (i * R ) 2 + n F ni RI = 2 R 2 * enRI * F + 2 * enRF 2 RI eno2 VOCM Noise and Noise Figure The LTC6409's differential input referred voltage and current noise densities are 1.1nV/Hz and 8.8pA/Hz, respectively. In addition to the noise generated by the amplifier, the surrounding feedback resistors also contribute noise. A simplified noise model is shown in Figure 4. The output noise generated by both the amplifier and the feedback components is given by the equation: enRF2 100 TOTAL (AMPLIFIER AND FEEDBACK NETWORK) OUTPUT NOISE 10 FEEDBACK NETWORK NOISE 1 0.1 10 100 1000 RI = RF () 10000 6409 F05 Figure 5. LTC6409 Output Noise vs Noise Contributed by Feedback Network Alone Lower resistor values always result in lower noise at the penalty of increased distortion due to increased loading by the feedback network on the output. Higher resistor values will result in higher output noise, but typically improved distortion due to less loading on the output. For this reason, when LTC6409 is configured in a differential gain of 1, using feedback resistors of at least 150 is recommended. To calculate noise figure (NF), a source resistance and the noise it generates should also come into consideration. Figure 6 shows a noise model for the amplifier which includes the source resistance (RS). To generalize the 6409fb For more information www.linear.com/LTC6409 LTC6409 APPLICATIONS INFORMATION enRI2 RI RF Finally, noise figure can be obtained as: enRF2 eno2 NF = 10log 1+ eno2(RS) in+2 RS RT + eno2 VOCM enRS2 in-2 enRT2 enRI2 - eni2 RI RF enRF2 6409 F06 Figure 6. A More General Noise Model Including Source and Termination Resistors calculation, a termination resistor (RT) is included and its noise contribution is taken into account. Now, the total output noise power (excluding the noise contribution of RS) is calculated as: eno RF 2 = e * 1+ ni R + R T || RS I 2 2 + 2 * (i * R ) 2 + n F 2 RF +2*e 2 * enRI * nRF || R R S RI + T 2 2 RF 2RI || RS * enRT * RI R T + ( 2RI || RS ) 2 + Meanwhile, the output noise power due to noise of RS is given by: eno 2 RF = (RS) e nRS * RI 2 2RI || R T * RS + ( 2RI || R T ) Figure 7 specifies the measured total output noise (eno), excluding the noise contribution of source resistance, and noise figure (NF) of LTC6409 configured at closed loop gains (AV = RF /RI) of 1V/V, 2V/V and 5V/V. The circuits in the left column use termination resistors and transformers to match to the 50 source resistance, while the circuits in the right column do not have such matching. For simplicity, DC-blocking and bypass capacitors have not been shown in the circuits, as they do not affect the noise results. Relationship Between Different Linearity Metrics Linearity is, of course, an important consideration in many amplifier applications. This section relates the inter-modulation distortion of fully differential amplifiers to other linearity metrics commonly used in RF style blocks. Intercept points are specifications that have long been used as key design criteria in the RF communications world as a metric for the intermodulation distortion performance of a device in the signal chain (e.g., amplifiers, mixers, etc.). Intercept points, like noise figures, can be easily cascaded back and forth through a signal chain to determine the overall performance of a receiver chain, thus resulting in simpler system-level calculations. Traditionally, these systems use primarily single-ended RF amplifiers as gain blocks designed to operate in a 50 environment, just like the rest of the receiver chain. Since intercept points are given in dBm, this implies an associated impedance of 50. However, for LTC6409 as a differential feedback amplifier with low output impedance, a 50 resistive load is not required (unlike an RF amplifier). This distinction is important when evaluating the intercept point for LTC6409. In fact, the LTC6409 yields optimum distortion performance when loaded with 200 to 1k (at each output), very similar to the input impedance of an ADC. As a result, terminating the input of the ADC to 50 can actually be detrimental to system performance. 6409fb For more information www.linear.com/LTC6409 13 LTC6409 APPLICATIONS INFORMATION 1.3pF 150 1:4 50 VIN + - 150 + 600 VIN 1pF - 100 1pF 0.4pF 0.8pF 500 50 eno = 11.69nV/Hz NF = 8.81dB - 500 VIN VOCM + - - 50 0.4pF NF = 16.66dB 250 + 50 eno = 9.76nV/Hz 200 1pF VOCM 100 VIN VOCM + - NF = 17.59dB 200 + 50 200 + + - 100 NF = 10.43dB - 1:4 50 1pF eno = 5.77nV/Hz eno = 5.88nV/Hz 150 1.3pF VOCM 100 - 150 200 100 VOCM + - 1.3pF + + - VIN 150 + 50 150 100 VIN NF = 14.41dB - 1:4 150 eno = 4.70nV/Hz VOCM 150 50 1.3pF 250 eno = 14.23nV/Hz NF = 13.56dB 6409 F07 0.8pF Figure 7. LTC6409 Measured Output Noise and Noise Figure at Different Closed Loop Gains with and without Source Impedance Matching The definition of 3rd order intermodulation distortion (IMD3) is shown in Figure 8. Also, a graphical representation of how to relate IMD3 to output/input 3rd order intercept points (OIP3/IIP3) has been depicted in Figure 9. Based on this figure, Equation (4) gives the definition of the intercept point, relative to the intermodulation distortion. IMD3 OIP3 = PO + 2 14 (4) PO is the output power of each of the two tones at which IMD3 is measured, as shown in Figure 9. It is calculated in dBm as: V 2 PDIFF PO = 10log -3 2 * R * 10 L (5) where RL is the differential load resistance, and VPDIFF is the differential peak voltage for a single tone. Normally, intermodulation distortion is specified for a benchmark composite differential peak of 2VP-P at the output of the 6409fb For more information www.linear.com/LTC6409 LTC6409 APPLICATIONS INFORMATION results in a lower intercept point. Therefore, it is important to consider the impedance seen by the output of the LTC6409 when working with intercept points. f = f2 - f1 = f1 - (2f1 - f2) = (2f2 - f1) - f2 PO POWER PO Comparing linearity specifications between different amplifier types becomes easier when a common impedance level is assumed. For this reason, the intercept points for LTC6409 are reported normalized to a 50 load impedance. This is the reason why OIP3 in the Electrical Characteristics table is 4dBm more than half the absolute value of IMD3. IMD3 = PS - PO PS PS 2f1 - f2 f1 f2 2f2 - f1 FREQUENCY 6409 F08 Figure 8. Definition of IMD3 POUT (dBm) If the top half of the LTC6409 demo board (DC1591A, shown in Figure 12) is used to measure IMD3 and OIP3, one should make sure to properly convert the power seen at the differential output of the amplifier to the power that appears at the single-ended output of the demo board. Figure 10 shows an equivalent representation of the top half of the demo board. This view ignores the DC-blocking and bypass capacitors, which do not affect the analysis here. The transmission line transformers (used mainly for impedance matching) are modeled here as ideal 4:1 impedance transformers together with a -1dB block. This separates the insertion loss of the transformer from its ideal behavior. The 100 resistors at the LTC6409 output create a differential 200 resistance, which is an impedance match for the reflected RL. 1x OIP3 PO PS IMD3 IIP3 3x PIN (dBm) 6409 F10 Figure 9. Graphical Representation of the Relationship between IMD3 and OIP3 As previously mentioned, IMD3 is measured for 2VP-P differential peak (i.e. 10dBm) at the output of the LTC6409, corresponding to 1VP-P (i.e. 4dBm) at each output alone. From LTC6409 output (location A in Figure 10) to the input of the output transformer (location B), there is a voltage attenuation of 1/2 (or -6dB) formed by the amplifier, implying that each single tone is 1VP-P, resulting in VPDIFF = 0.5V. Using RL = 50 as the associated impedance, PO is calculated to be close to 4dBm. As seen in Equation (5), when a higher impedance is used, the same level of intermodulation distortion performance CF RF RS 50 + - VS RT 1dB LOSS 100 RI IDEAL 1:4 RT LTC6409 A 100 RI C B IDEAL 4:1 1dB LOSS RL 50 6409 F10 RF CF Figure 10. Equivalent Schematic of the Top Half of the LTC6409 Demo Board 6409fb For more information www.linear.com/LTC6409 15 LTC6409 APPLICATIONS INFORMATION resistive divider between the RL * 4 = 200 differential resistance seen at location B and the 200 formed by the two 100 matching resistors at the LTC6409 output. Thus, the differential power at location B is 10 - 6 = 4dBm. Since the transformer ratio is 4:1 and it has an insertion loss of about 1dB, the power at location C (across RL) is calculated to be 4 - 6 - 1 = -3dBm. This means that IMD3 should be measured while the power at the output of the demo board is -3dBm which is equivalent to having 2VP-P differential peak (or 10dBm) at the output of the LTC6409. GBW vs f-3dB Gain-bandwidth product (GBW) and -3dB frequency (f-3dB) have been both specified in the Electrical Characteristics table as two different metrics for the speed of the LTC6409. GBW is obtained by measuring the gain of the amplifier at a specific frequency (fTEST) and calculate gain * fTEST. To measure gain, the feedback factor (i.e. = RI/(RI + RF)) is chosen sufficiently small so that the feedback loop does not limit the available gain of the LTC6409 at fTEST, ensuring that the measured gain is the open loop gain of the amplifier. As long as this condition is met, GBW is a parameter that depends only on the internal design and compensation of the amplifier and is a suitable metric to specify the inherent speed capability of the amplifier. f-3dB, on the other hand, is a parameter of more practical interest in different applications and is by definition the frequency at which the gain is 3dB lower than its low frequency value. The value of f-3dB depends on the speed of the amplifier as well as the feedback factor. Since the LTC6409 is designed to be stable in a differential signal gain of 1 (where RI = RF or = 1/2), the maximum f-3dB is obtained and measured in this gain setting, as reported in the Electrical Characteristics table. In most amplifiers, the open loop gain response exhibits a conventional single-pole roll-off for most of the frequencies before crossover frequency and the GBW and f-3dB numbers are close to each other. However, the LTC6409 is intentionally compensated in such a way that its GBW is significantly larger than its f-3dB. This means that at 16 lower frequencies (where the input signal frequencies typically lie, e.g. 100MHz) the amplifier's gain and thus the feedback loop gain is larger. This has the important advantage of further linearizing the amplifier and improving distortion at those frequencies. Looking at the Frequency Response vs Closed Loop Gain graph in the Typical Performance Characteristics section of this data sheet, one sees that for a closed loop gain (AV) of 1 (where RI = RF = 150), f-3dB is about 2GHz. However, for AV = 400 (where RI = 25 and RF = 10k), the gain at 100MHz is close to 40dB = 100V/V, implying a GBW value of 10GHz. Feedback Capacitors When the LTC6409 is configured in low differential gains, it is often advantageous to utilize a feedback capacitor (CF) in parallel with each feedback resistor (RF). The use of CF implements a pole-zero pair (in which the zero frequency is usually smaller than the pole frequency) and adds positive phase to the feedback loop gain around the amplifier. Therefore, if properly chosen, the addition of CF boosts the phase margin and improves the stability response of the feedback loop. For example, with RI = RF = 150, it is recommended for most general applications to use CF = 1.3pF across each RF. This value has been selected to maximize f-3dB for the LTC6409 while keeping the peaking of the closed loop gain versus frequency response under a reasonable level (<1dB). It also results in the highest frequency for 0.1dB gain flatness (f0.1dB). However, other values of CF can also be utilized and tailored to other specific applications. In general, a larger value for CF reduces the peaking (overshoot) of the amplifier in both frequency and time domains, but also decreases the closed loop bandwidth (f-3dB). For example, while for a closed loop gain (AV) of 5, CF = 0.8pF results in maximum f-3dB (as previously shown in the Frequency Response vs Closed Loop Gain graph of this data sheet), if CF = 1.2pF is used, the amplifier exhibits no overshoot in the time domain which is desirable in certain applications. Both the circuits discussed in this section have been shown in the Typical Applications section of this data sheet. 6409fb For more information www.linear.com/LTC6409 LTC6409 APPLICATIONS INFORMATION Board Layout and Bypass Capacitors Driving ADCs For single supply applications, it is recommended that high quality 0.1F||1000pF ceramic bypass capacitors be placed directly between each V+ pin and its closest V- pin with short connections. The V- pins (including the Exposed Pad) should be tied directly to a low impedance ground plane with minimal routing. The LTC6409's ground-referenced input, differential output and adjustable output common mode voltage make it ideal for interfacing to differential input ADCs. These ADCs are typically supplied from a single-supply voltage and have an optimal common mode input range near midsupply. The LTC6409 interfaces to these ADCs by providing single-ended to differential conversion and common mode level shifting. For dual (split) power supplies, it is recommended that additional high quality 0.1F||1000pF ceramic capacitors be used to bypass V+ pins to ground and V- pins to ground, again with minimal routing. For driving heavy differential loads (<200), additional bypass capacitance may be needed for optimal performance. Keep in mind that small geometry (e.g., 0603) surface mount ceramic capacitors have a much higher self-resonant frequency than do leaded capacitors, and perform best in high speed applications. To prevent degradation in stability response, it is highly recommended that any stray capacitance at the input pins, +IN and -IN, be kept to an absolute minimum by keeping printed circuit connections as short as possible. This becomes especially true when the feedback resistor network uses resistor values greater than 500 in circuits with RI = RF. At the output, always keep in mind the differential nature of the LTC6409, because it is critical that the load impedances seen by both outputs (stray or intended), be as balanced and symmetric as possible. This will help preserve the balanced operation of the LTC6409 that minimizes the generation of even-order harmonics and maximizes the rejection of common mode signals and noise. The VOCM pin should be bypassed to the ground plane with a high quality ceramic capacitor of at least 0.01F. This will prevent common mode signals and noise on this pin from being inadvertently converted to differential signals and noise by impedance mismatches both externally and internally to the IC. The sampling process of ADCs creates a transient that is caused by the switching in of the ADC sampling capacitor. This momentarily shorts the output of the amplifier as charge is transferred between amplifier and sampling capacitor. The amplifier must recover and settle from this load transient before the acquisition period has ended, for a valid representation of the input signal. The LTC6409 will settle quickly from these periodic load impulses. The RC network between the outputs of the driver and the inputs of the ADC decouples the sampling transient of the ADC (see Figure 11). The capacitance serves to provide the bulk of the charge during the sampling process, while the two resistors at the outputs of the LTC6409 are used to dampen and attenuate any charge injected by the ADC. The RC filter gives the additional benefit of band limiting broadband output noise. Generally, longer time constants improve SNR at the expense of settling time. The resistors in the decoupling network should be at least 10. These resistors also serve to decouple the LTC6409 outputs from load capacitance. Too large of a resistor will leave insufficient settling time. Too small of a resistor will not properly dampen the load transient of the sampling process, prolonging the time required for settling. In 16bit applications, this will typically require a minimum of eleven RC time constants. For lowest distortion, choose capacitors with low dielectric absorption (such as a C0G multilayer ceramic capacitor). 6409fb For more information www.linear.com/LTC6409 17 LTC6409 APPLICATIONS INFORMATION 1.3pF VIN 150 150 2 +IN 33.2 1 -OUT LTC6409 SHDN SHDN V- 3 V+ 5V 4 V+ V+ VOCM V+ 9 5V - 5 V VOCM V- 0.1F 6 150 -IN 150 10 0.1F||1000pF + 0.1F||1000pF CONTROL V- 10 7 0.1F||1000pF - AIN+ 39pF 10 39pF LTC2262-14 ADC AIN- VCM GND VDD D13 * * D0 1.8V 1F 8 +OUT 1F 6409 F11 33.2 100 1.3pF Figure 11. Driving an ADC 18 6409fb For more information www.linear.com/LTC6409 LTC6409 APPLICATIONS INFORMATION R5 150, 0.1% C22 1.3pF V+ J1 IN T1 TCM4-19 1:4 XFMR MINI-CIRCUITS Sd 3 R14 0 4 C23 0.1F 6 Pd R13 OPT C25 0.1F CT 2 4 P S 1 R9 150, 0.1% C24 0.1F 2 5 R10 150, 0.1% R12 300 6 3 R11 300 V+ 1 -OUT C19 0.1F LTC6409UDB VOCM -IN SHDN R3 100 V- V- +OUT 7 V- 11 10 T2 TCM4-19 4:1 XFMR MINI-CIRCUITS 1 S C18 0.1F C29 0.1F P R1 0 4 2 CT 3 R2 OPT Pd 6 Sd J2 OUT R4 100 8 VCM C32 0.1F R15 OPT R16 OPT 9 +IN E2 V+ E4 VOCM V+ C26 0.1F C28 0.1F SHDN1 1 DIS 2 3 EN R17 10 C27 1.3pF R8 150, 0.1% JP1 CALIBRATION PATH T3 TCM4-19 1:4 XFMR MINI-CIRCUITS Sd 3 R18 0 J3 CAL IN C31 0.1F 6 Pd C30 0.1F CT 2 R19 OPT 4 P S C20 0.1F 1 R21 75 R20 300 R24 75 T4 TCM4-19 4:1 XFMR MINI-CIRCUITS 1 S C14 0.1F R22 300 R23 300 C15 0.1F P C21 0.1F R27 0 4 2 CT 3 R26 OPT Pd 6 Sd R25 300 C1 100pF R28 150, 0.1% C2 0.01F C13 1.3pF V+ 4 J5 +IN J6 -IN R31 0 R37 0 V+ R33 150, 0.1% 2 R32 OPT R39 VOCM 150, 0.1% R38 OPT C16 0.1F 5 6 3 C3 0.1F 9 V+ 1 +IN VOCM SHDN R34 50 -OUT LTC6409UDB -IN V- V- V- 11 10 8 +OUT 7 R40 50 R36 0 R35 OPT R6 OPT R7 0 C4 0.47F J7 -OUT C5 100pF V+ R30 10 C17 1.3pF R29 150, 0.1% C6 0.01F E1 V+ J8 +OUT C12 10F C7 0.1F C10 1000pF C11 0.1F SHDN2 1 DIS 2 3 EN J4 CAL OUT C9 1000pF C8 0.47F E3 GND JP2 6409 F12 Figure 12. Demo Board DC1591A Schematic 6409fb For more information www.linear.com/LTC6409 19 LTC6409 APPLICATIONS INFORMATION Figure 13. Demo Board DC1591A Layout 20 6409fb For more information www.linear.com/LTC6409 LTC6409 TYPICAL APPLICATIONS DC-Coupled Level Shifting of an I/Q Demodulator Output C5 0.9pF 5V LT5575 5V 5V 65 65 I RF IN 1900MHz -10dBm 200mVP-P 5V LO 1920MHz 0dBm 5V C1 10pF 5V R1 75 R3 75 R2 75 C3 R4 12pF 75 -OUT LTC6409 - + +OUT VOCM 1.25V 65 65 3.4dBm 936mVP-P + - C2 10pF 5pF 5pF Q -8.9dBm 227mVP-P DC LEVEL 1.25V R5 620 DC LEVEL 3.9V 5pF 5pF DC LEVEL 3.4V DIFF OUTPUT Z 130| |2.5pF R6 620 IDENTICAL Q CHANNEL C4 0.9pF 6409 TA02 GAIN: 1.1dB GAIN: 12.3dB Single-Ended to Differential Conversion Using LTC6409 and 50MHz Lowpass Filter (Only One Channel Shown) 3.3V 0.8pF 1.8V 0.1F - SHDN +OUT VOCM 75 33pF 68pF 37.4 180nH 150pF 180nH O1A+ E8 - B1 AIN1 O1A- E7 DCO+ G7 B3 C2 0.8pF 66.5 + B2 AIN1 75 474 C1 F2 F1 GND OVDD 150pF F3 G2 G1 N1 N2 DCO- G8 VCM12 + AIN2 FR+ H8 FR- H7 LTM9011-14 AIN2- AIN3+ AIN3- VCM34 AIN4+ AIN4- AIN8+ AIN8- 6409 TA03 CLK- LTC6409 68pF B6 VREF -OUT 180nH CLK+ -IN + 180nH SENSE +IN 150 37.4 V+ VDD C5 66.5 49.9 1.8V 474 * * * INPUT 150 P5 P6 6409fb For more information www.linear.com/LTC6409 21 LTC6409 PACKAGE DESCRIPTION Please refer to http://www.linear.com/product/LTC6409#packaging for the most recent package drawings. UDB Package 10-Lead Plastic QFN (3mm x 2mm) (Reference LTC DWG # 05-08-1848 Rev A) 0.25 0.05 0.95 0.05 0.65 0.05 2.50 0.05 1.10 0.05 0.75 0.05 0.90 0.05 0.05 0.05 DETAIL B DETAIL B PACKAGE OUTLINE 0.25 0.10 0.25 0.05 0.50 BSC 0.85 0.05 0.90 0.10 0.05 0.10 DETAIL A 3.50 0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 0.40 0.10 2.00 0.05 3.00 0.05 0.75 0.05 0.20 REF SIDE VIEW R = 0.13 TYP 8 1 0.80 7 BSC 6 0.50 0.10 0.25 0.05 0.50 BSC 0.70 0.10 10 DETAIL A 2 5 3 0.60 0.10 (UDB10) DFN 0910 REV A BOTTOM VIEW--EXPOSED PAD 0.00 - 0.05 NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 22 6409fb For more information www.linear.com/LTC6409 LTC6409 REVISION HISTORY REV DATE DESCRIPTION PAGE NUMBER A 12/10 Revised Typical Application drawing 21 B 05/17 Corrected spelling of "reflectometry" 1 6409fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its information circuits as described herein will not infringe on existing patent rights. For more www.linear.com/LTC6409 23 LTC6409 TYPICAL APPLICATIONS LTC6409 Externally Compensated for Maximum Gain Flatness and for No-Overshoot Time-Domain Response 1.3pF Gain 0.1dB Flatness 0.5 150 0.1F 75 PORT 1 50 PORT 2 50 150 VOCM = 1.25V 0.1F 0.4 5V 75 150 - + LTC6409 + - 150 150 0.1F 0.1F 0.3 1/2 AGILENT E5071A PORT 3 50 0.2 GAIN (dB) 1/2 AGILENT E5071A PORT 4 50 0.1 0 -0.1 -0.2 -0.3 150 -0.4 -0.5 1.3pF 1.2pF 1 10 100 1000 FREQUENCY (MHz) 10000 No-Overshoot Step Response 250 50 0.4VP-P + - VIN 5V 50 0.1F VOCM = 1.25V 50 - + LTC6409 + - 150 150 0.1F 0.1F 49.9 -OUT TEKTRONIX CSA8200 SCOPE CHANNEL 1 50 0.2V/DIV 0.1F CHANNEL 2 50 6409 TA04 +OUT 250 2ns/DIV 1.2pF RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC6400-8/LTC6400-14/ 1.8GHz Low Noise, Low Distortion, Differential LTC6400-20/LTC6400-26 ADC Drivers -71dBc IM3 at 240MHz 2VP-P Composite, IS = 90mA, A V = 8dB/14dB/20dB/26dB LTC6401-8/LTC6401-14/ 1.3GHz Low Noise, Low Distortion, Differential LTC6401-20/LTC6401-26 ADC Drivers -74dBc IM3 at 140MHz 2VP-P Composite, IS = 50mA, A V = 8dB/14dB/20dB/26dB LTC6406/LTC6405 3GHz/2.7GHz Low Noise, Rail-to-Rail Input Differential Amplifier/Driver -70dBc/-65dBc Distortion at 50MHz, IS = 18mA, 1.6nV/Hz Noise, 3V/5V Supply LTC6416 2GHz Low Noise, Differential 16-Bit ADC Buffer -72.5dBc IM3 at 300MHz 2VP-P Composite, 150mW on 3.6V Supply LTC2209 16-Bit, 160Msps ADC 100dB SFDR, VDD = 3.3V, VCM = 1.25V LTC2262-14 14-Bit, 150Msps Ultralow Power 1.8V ADC 88dB SFDR, 149mW, VDD = 1.8V, VCM = 0.9V 24 6409fb LT 0517 REV B * PRINTED IN USA For more information www.linear.com/LTC6409 www.linear.com/LTC6409 LINEAR TECHNOLOGY CORPORATION 2010