80001414822 - 3M - Datasheet.Directory

MR4A16B Rev. 11.7 3/20181

INTRODUCTION

The MR4A16B is a 16,777,216-bit magnetoresistive random access memory

(MRAM) device organized as 1,048,576 words of 16 bits. The MR4A16B oers

SRAM compatible 35 ns read/write timing with unlimited endurance. Data

is always non-volatile for greater than 20 years. Data is automatically pro-

tected on power loss by low-voltage inhibit circuitry to prevent writes with voltage out of specication. To

simplify fault tolerant design, the MR4A16B includes internal single bit error correction code with 7 ECC

parity bits for every 64 data bits. The MR4A16B is the ideal memory solution for applications that must

permanently store and retrieve critical data and programs quickly.

The MR4A16B is available in a small footprint 48-pin ball grid array (BGA) package and a 54-pin thin small

outline package (TSOP Type 2). These packages are compatible with similar low-power SRAM products and

other nonvolatile RAM products.

The MR4A16B provides highly reliable data storage over a wide range of temperatures. The product is

oered with commercial temperature (0 to +70 °C), and industrial temperature (-40 to +85 °C) operating

temperature options.

MR4A16B

1M x 16 MRAM

FEATURES

• +3.3 Volt power supply

• Fast 35 ns read/write cycle

• SRAM compatible timing

• Unlimited read & write endurance

• Data always non-volatile for >20 years at temperature

• RoHS-compliant small footprint BGA and TSOP2 package

• All products meet MSL-3 moisture sensitivity level

BENEFITS

• One memory replaces FLASH, SRAM, EEPROM and BBSRAM in systems

for simpler, more ecient designs

• Improves reliability by replacing battery-backed SRAM

RoHS

CONTENTS

1. DEVICE PIN ASSIGNMENT......................................................................... 3

2. ELECTRICAL SPECIFICATIONS................................................................. 4

3. TIMING SPECIFICATIONS.......................................................................... 7

4. ORDERING INFORMATION....................................................................... 12

5. MECHANICAL DRAWING.......................................................................... 13

6. REVISION HISTORY...................................................................................... 15

How to Reach Us...................................................................................... .......... 16

CHIP

ENABLE

BUFFER

OUTPUT

ENABLE

BUFFER

ADDRESS

BUFFER

WRITE

ENABLE

BUFFER

UPPER BYTE OUTPUT ENABLE

LOWER BYTE OUTPUT ENABLE

1M x 16

BIT

MEMORY

ARRAY

ROW

DECODER COLUMN

DECODER

SENSE

AMPS

LOWER

BYTE

WRITE

DRIVER

LOWER

BYTE

OUTPUT

BUFFER

UPPER

BYTE

OUTPUT

BUFFER

FINAL

WRITE

DRIVERS

UPPER BYTE WRITE ENABLE

LOWER BYTE WRITE ENABLE

BYTE

ENABLE

BUFFER

A[19:0]

DQL[7:0]

8DQU[15:8]

UPPER

BYTE

WRITE

DRIVER

1. DEVICE PIN ASSIGNMENT

Figure 1.1 Block Diagram

Table 1.1 Pin Functions

Signal Name Function

A Address Input

E Chip Enable

W Write Enable

G Output Enable

UB Upper Byte Enable

LB Lower Byte Enable

DQ Data I/O

VDD Power Supply

VSS Ground

DC Do Not Connect

NC No Connection

MR4A16B

MR4A16B Rev. 11.7 3/20183

123456

LB G A0 A1 A2 NC A

DQU8 UB A3 A4 E DQL0 B

DQU9 DQU10 A5 A6 DQL1 DQL2 C

VSS DQU11

A15

DQL3 VDD D

VDD DQU12 DC A16 DQL4 VSS E

DQU14 DQU13 A14

A13

DQL5 DQL6 F

DQU15

A10

A17

A11

WDQL7 G

A9A8

A12

A19

DQ0

DQ1

DQ2

DQ3

DQ4

DQ5

DQ6

DQ7

A18

A17

A16

A15

A14

A13

A12

A11

A10

DQ15

DQ14

DQ13

DQ12

DQ11

DQ10

DQ9

DQ8

Figure 1.1 Pin Diagrams for Available Packages (Top View)

48-Pin BGA 54-Pin TSOP2

Table 1.2 Operating Modes

DEVICE PIN ASSIGNMENT MR4A16B

E1G1W1LB1UB1Mode VDD Current DQL[7:0]2DQU[15:8]2

H X X X X Not selected ISB1, ISB2 Hi-Z Hi-Z

L H H X X Output disabled IDDR Hi-Z Hi-Z

L X X H H Output disabled IDDR Hi-Z Hi-Z

L L H L H Lower Byte Read IDDR DOut Hi-Z

L L H H L Upper Byte Read IDDR Hi-Z DOut

L L H L L Word Read IDDR DOut DOut

L X L L H Lower Byte Write IDDW Din Hi-Z

L X L H L Upper Byte Write IDDW Hi-Z Din

L X L L L Word Write IDDW Din Din

1 H = high, L = low, X = don’t care

2 Hi-Z = high impedance

2. ELECTRICAL SPECIFICATIONS

Absolute Maximum Ratings

This device contains circuitry to protect the inputs against damage caused by high static voltages or

electric elds; however, it is advised that normal precautions be taken to avoid application of any

voltage greater than maximum rated voltages to these high-impedance (Hi-Z) circuits.

The device also contains protection against external magnetic elds. Precautions should be taken

to avoid application of any magnetic eld greater than the maximum eld intensity specied

in the maximum ratings.

Symbol Parameter Conditions Value Unit

VDD Supply voltage2 -0.5 to 4.0 V

VIN Voltage on an pin 2-0.5 to VDD + 0.5 V

IOUT Output current per pin ±20 mA

PDPackage power dissipation 30.600 W

TBIAS Temperature under bias Commercial -10 to 85 °C

Industrial -45 to 95 °C

Tstg Storage Temperature -55 to 150 °C

TLead

Lead temperature during solder (3

minute max) 260 °C

Hmax_write Maximum magnetic eld During Write

8000 A/m

Hmax_read Maximum magnetic eld During Read or Standby

1 Permanent device damage may occur if absolute maximum ratings are exceeded. Functional operation

should be restricted to recommended operating conditions. Exposure to excessive voltages or magnetic

elds could aect device reliability.

2 All voltages are referenced to VSS. The DC value of VIN must not exceed actual applied VDD by more than

0.5V. The AC value of VIN must not exceed applied VDD by more than 2V for 10ns with IIN limited to less than

20mA.

3 Power dissipation capability depends on package characteristics and use environment.

Table 2.1 Absolute Maximum Ratings 1

MR4A16B

MR4A16B Rev. 11.7 3/20185

Symbol Parameter Temp Range Min Typical Max Unit

VDD Power supply voltage 3.0 13.3 3.6 V

VWI Write inhibit voltage 2.5 2.7 3.0 1 V

VIH Input high voltage 2.2 - VDD + 0.3 2V

VIL Input low voltage -0.5 3- 0.8 V

TATemperature under bias

Commercial 0 - 70 °C

Industrial -40 - 85 °C

1 There is a 2 ms startup time once VDD exceeds VDD,(min). See Power Up and Power Down Sequencing below.

2 VIH(max) = VDD + 0.3 VDC ; VIH(max) = VDD + 2.0 VAC (pulse width ≤ 10 ns) for I ≤ 20.0 mA.

3 VIL(min) = -0.5 VDC ; VIL(min) = -2.0 VAC (pulse width ≤ 10 ns) for I ≤ 20.0 mA.

Table 2.2 Operating Conditions

Power Up and Power Down Sequencing

The MRAM is protected from write operations whenever VDD is less than VWI. As soon as VDD exceeds VDD(min),

there is a startup time of 2 ms before read or write operations can start. This time allows memory power

supplies to stabilize.

The E and W control signals should track VDD on power up to VDD- 0.2 V or VIH (whichever is lower) and remain

high for the startup time. In most systems, this means that these signals should be pulled up with a resis-

tor so that a signal remains high if the driving signal is Hi-Z during power up. Any logic that drives E and W

should hold the signals high with a power-on reset signal for longer than the startup time.

During power loss or brownout where VDD goes below VWI, writes are protected and a startup time must be

observed when power returns above VDD(min).

Figure 2.1 Power Up and Power Down Diagram

MR4A16B

Electrical Specications

BROWNOUT or POWER LOSS

NORMAL

OPERATION

VDD

READ/WRITE

INHIBITED

VWI

2 ms

READ/WRITE

INHIBITED

VIH

STARTUP

NORMAL

OPERATION

2 ms

RECOVER

VIH

Symbol Parameter Conditions Min Max Unit

Ilkg(I) Input leakage current All - ±1 μA

Ilkg(O) Output leakage current All - ±1 μA

VOL Output low voltage

IOL = +4 mA - 0.4 V

IOL = +100 μA VSS + 0.2 V

VOH Output high voltage

IOH = -4 mA 2.4 - V

IOH = -100 μA VDD - 0.2 - V

Table 2.3 DC Characteristics

Table 2.4 Power Supply Characteristics

Symbol Parameter Typical Max Unit

IDDR

AC active supply current - read modes1

(IOUT= 0 mA, VDD= max) 60 68 mA

IDDW

AC active supply current - write modes1

(VDD= max) 152 180 mA

ISB1

AC standby current

(VDD= max, E = VIH)

no other restrictions on other inputs

9 14 mA

ISB2

CMOS standby current

(E ≥ VDD - 0.2 V and VIn ≤ VSS + 0.2 V or ≥ VDD - 0.2 V)

(VDD = max, f = 0 MHz)

5 9 mA

1 All active current measurements are measured with one address transition per cycle and at minimum cycle time.

MR4A16B

Electrical Specications

MR4A16B Rev. 11.7 3/20187

MR4A16B

3. TIMING SPECIFICATIONS

Table 3.1 Capacitance 1

Symbol Parameter Typical Max Unit

CIn Address input capacitance - 6 pF

CIn Control input capacitance - 6 pF

CI/O Input/Output capacitance - 8 pF

1 f = 1.0 MHz, dV = 3.0 V, TA = 25 °C, periodically sampled rather than 100% tested.

Table 3.2 AC Measurement Conditions

Figure 3.1 Output Load Test Low and High

Figure 3.2 Output Load Test All Others

Parameter Value Unit

Logic input timing measurement reference level 1.5 V

Logic output timing measurement reference level 1.5 V

Logic input pulse levels 0 or 3.0 V

Input rise/fall time 2 ns

Output load for low and high impedance parameters See Figure 3.1

Output load for all other timing parameters See Figure 3.2

Output

L= 1.5 V

RL= 50 Ω

ZD= 50 Ω

Output

435 Ω

590 Ω

5 pF

3.3 V

MR4A16B

Timing Specications

Symbol Parameter Min Max Unit

tAVAV Read cycle time 35 - ns

tAVQV Address access time - 35 ns

tELQV Enable access time 2- 35 ns

tGLQV Output enable access time - 15 ns

tBLQV Byte enable access time - 15 ns

tAXQX Output hold from address change 3 - ns

tELQX Enable low to output active 33 - ns

tGLQX Output enable low to output active 30 - ns

tBLQX Byte enable low to output active 30 - ns

tEHQZ Enable high to output Hi-Z 30 15 ns

tGHQZ Output enable high to output Hi-Z 30 10 ns

tBHQZ Byte high to output Hi-Z 30 10 ns

1 W is high for read cycle. Power supplies must be properly grounded and decoupled, and bus contention conditions must be

minimized or eliminated during read or write cycles.

2 Addresses valid before or at the same time E goes low.

3 This parameter is sampled and not 100% tested. Transition is measured ±200 mV from the steady-state voltage.

Table 3.3 Read Cycle Timing 1

Read Mode

Figure 3.3A Read Cycle 1

Figure 3.3B Read Cycle 2

A (ADDRESS)

Q (DATA OUT)

AVAV

AXQX

AVQV

Previous Data Valid

Note: Device is continuously selected (E≤V

, G≤V

Data Valid

A (ADDRESS)

E (CHIP ENABLE)

G (OUTPUT ENABLE)

Q (DATA OUT) Data Valid

AVAV

AVQV

ELQV

ELQX

BHQZ

GHQZ

EHQZ

BLQV

BLQX

GLQV

GLQX

LB, UB (BYTE ENABLE)

MR4A16B Rev. 11.7 3/20189

MR4A16B

Timing Specications

Table 3.4 Write Cycle Timing 1 (W Controlled) 1

Symbol Parameter Min Max Unit

tAVAV Write cycle time 235 - ns

tAVWL Address set-up time 0 - ns

tAVWH Address valid to end of write (G high) 20 - ns

tAVWH Address valid to end of write (G low) 20 - ns

tWLWH

tWLEH

Write pulse width (G high) 15 - ns

tWLWH

tWLEH

Write pulse width (G low) 15 - ns

tDVWH Data valid to end of write 10 - ns

tWHDX Data hold time 0 - ns

tWLQZ Write low to data Hi-Z 30 15 ns

tWHQX Write high to output active 33 - ns

tWHAX Write recovery time 12 - ns

1 All write occurs during the overlap of E low and W low. Power supplies must be properly grounded and decoupled and bus

contention conditions must be minimized or eliminated during read and write cycles. If G goes low at the same time or after

W goes low, the output will remain in a high impedance state. After W, E or UB/LB has been brought high, the signal must

remain in steady-state high for a minimum of 2 ns. The minimum time between E being asserted low in one cycle to E being

asserted low in a subsequent cycle is the same as the minimum cycle time allowed for the device.

2 All write cycle timings are referenced from the last valid address to the rst transition address.

3 This parameter is sampled and not 100% tested. Transition is measured ±200 mV from the steady-state voltage. At any given

voltage or temperate, tWLQZ(max) < tWHQX(min).

W (WRITE ENABLE)

A (ADDRESS)

E (CHIP ENABLE)

UB, LB (BYTE ENABLED)

AVAV

AVWH

WHAX

AVWL

WLEH

WLWH

DATA VALID

DVWH

WHDX

Q (DATA OUT)

D (DATA IN)

WLQZ

WHQX

Hi -Z Hi -Z

Figure 3.4 Write Cycle Timing 1 (W Controlled)

MR4A16B

Timing Specications

Table 3.5 Write Cycle Timing 2 (E Controlled) 1

Figure 3.5 Write Cycle Timing 2 (E Controlled)

Symbol Parameter Min Max Unit

tAVAV Write cycle time 235 - ns

tAVEL Address set-up time 0 - ns

tAVEH Address valid to end of write (G high) 20 - ns

tAVEH Address valid to end of write (G low) 20 - ns

tELEH

tELWH

Enable to end of write (G high) 15 - ns

tELEH

tELWH

Enable to end of write (G low) 315 - ns

tDVEH Data valid to end of write 10 - ns

tEHDX Data hold time 0 - ns

tEHAX Write recovery time 12 - ns

1 All write occurs during the overlap of E low and W low. Power supplies must be properly grounded and decoupled and bus

contention conditions must be minimized or eliminated during read and write cycles. If G goes low at the same time or after

W goes low, the output will remain in a high impedance state. After W, E or UB/ LB has been brought high, the signal must

remain in steady-state high for a minimum of 2 ns. The minimum time between E being asserted low in one cycle to E being

asserted low in a subsequent cycle is the same as the minimum cycle time allowed for the device.

2 All write cycle timings are referenced from the last valid address to the rst transition address.

3 If E goes low at the same time or after W goes low, the output will remain in a high-impedance state. If E goes high at the

same time or before W goes high, the output will remain in a high-impedance state.

A (ADDRESS)

E (CHIP ENABLE)

W (WRITE ENABLE)

Q (DATA OUT)

D (DATA IN)

AVAV

AVEH

EHAX

ELEH

EHDX

DVEH

AVEL

Hi-Z

ELWH

Data Valid

UB, LB (BYTE ENABLE)

MR4A16B Rev. 11.7 3/201811

MR4A16B

Timing Specications

Table 3.6 Write Cycle Timing 3 (LB/UB Controlled) 1

Figure 3.6 Write Cycle Timing 3 (LB/UB Controlled)

Symbol Parameter Min Max Unit

tAVAV Write cycle time 235 - ns

tAVBL Address set-up time 0 - ns

tAVBH Address valid to end of write (G high) 20 - ns

tAVBH Address valid to end of write (G low) 20 - ns

tBLEH

tBLWH

Write pulse width (G high) 15 - ns

tBLEH

tBLWH

Write pulse width (G low) 15 - ns

tDVBH Data valid to end of write 10 - ns

tBHDX Data hold time 0 - ns

tBHAX Write recovery time 12 - ns

1 All write occurs during the overlap of E low and W low. Power supplies must be properly grounded and decoupled and bus

contention conditions must be minimized or eliminated during read and write cycles. If G goes low at the same time or after W

goes low, the output will remain in a high impedance state. After W, E or UB/LB has been brought high, the signal must remain

in steady-state high for a minimum of 2 ns. If both byte control signals are asserted, the two signals must have no more than 2

ns skew between them. The minimum time between E being asserted low in one cycle to E being asserted low in a subsequent

cycle is the same as the minimum cycle time allowed for the device.

2 All write cycle timings are referenced from the last valid address to the rst transition address.

W (WRITE ENABLE)

A (ADDRESS)

E (CHIP ENABLE)

UB, LB (BYTE ENABLED)

tAVAV

tAVEH tBHAX

tAVBL tBLEH

tBLWH

Data Valid

tDVBH tBHDX

Q (DATA OUT)

D (DATA IN)

Hi -Z Hi -Z

MR4A16B

4. ORDERING INFORMATION

Figure 4.1 Part Numbering System

Carrier Blank = Tray, R = Tape & Reel

Speed 35 ns

Package MA = FBGA, YS = TSOP

Temperature Range Blank= Commercial (0 to +70 °C),

C= Industrial (-40 to +85°C )

Revision

Data Width 16 = 16-bit

Type A = Asynchronous

Density 4 =16Mb

Magnetoresistive RAM

MR 4 A 16 B C MA 35 R

Grade Temp Range Package Shipping Con-

tainer Order Part Number

Commercial 0 to +70 °C

48-BGA Trays MR4A16BMA35

Tape & Reel MR4A16BMA35R

54-TSOP2 Trays MR4A16BYS35

Tape & Reel MR4A16BYS35R

Industrial -40 to +85°C

48-BGA Tray MR4A16BCMA35

Tape & Reel MR4A16BCMA35R

54-TSOP2 Tray MR4A16BCYS35

Tape & Reel MR4A16BCYS35R

Table 4.1 Available Parts

MR4A16B Rev. 11.7 3/201813

MR4A16B

5. MECHANICAL DRAWING

123456

(DATUM A)

(DATUM B)

SEATING PLANE

PIN A1

INDEX

PIN A1

INDEX

BOTTOM VIEW TOP VIEW

SOLDER BALL DIAMETER REFERS

TO POST REFLOW CONDITION.

THE PRE-REFLOW DIAMETER IS

0.35mm

Figure 5.1 48-FBGA

Print Version Not To Scale

1. Dimensions in Millimeters.

2. The ‘e’ represents the basic solder ball grid pitch.

3. ‘b’ is measurable at the maximum solder ball diameter

in a plane parallel to datum C.

4. Dimension ‘ddd’ is measured parallel to primary datum

5. Primary datum C (seating plane) is dened by the

crowns

of the solder balls.

6. Package dimensions refer to JEDEC MO-205 Rev. G.

Ref Min Nominal Max

A 1.19 1.27 1.35

A1 0.22 0.27 0.32

b0.31 0.36 0.41

D10.00 BSC

E10.00 BSC

D1 5.25 BSC

E1 3.75 BSC

DE 0.375 BSC

SE 0.375 BSC

e0.75 BSC

Ref Tolerance of, from and position

aaa 0.10

bbb 0.10

ddd 0.10

eee 0.15

f 0.08

MR4A16B

5. MECHANICAL DRAWING

0.10

SEATING PLANE

0.71 REF.

54 28

A2 A1

0.21(0.008)REF.

GAGE PLANE

0.25 mm

0.665(0.026)REF.

⊕0.20(0.008) M

Figure 5.2 54-TSOP2

Print Version Not To Scale

1. Dimensions in Millimeters.

2. Package dimensions refer to JEDEC MS-024

Ref Min Nominal Max

A 1.20

A1 0.05 0.10 0.15

A2 0.95 1.00 1.05

b0.30 0.35 0.45

c0.12 0.21

D22.10 22.22 22.35

E11.56 11.76 11.95

E1 10.03 10.16 10.29

e0.80 BSC

L0.40 0.50 0.60

L1 0.80 REF

R1 0.12 - -

R2 0.12 - 0.25

θ0° - 8°

θ1 0.40 - -

θ2 15° REF

θ3 15° REF

MR4A16B Rev. 11.7 3/201815

MR4A16B

Rev Date Description of Change

1 May 29, 2009 Establish Speed and Power Specications

2 July 27, 2009 Increase BGA Package to 11 mm x 11 mm

3 Nov 26, 2009 Changed ball denition of H6 to A19 and G2 to NC in Figure 1.2.

4 Mar 10, 2010 Changed speed marking and timing specs to 35 ns part. Changed BGA package to 10 mm x 10mm

5 Apr 7, 2010 Added 54-TSOP package options.

6 Oct 7, 2011

Added AEC-Q100 Grade 1 product option. Max. magnetic eld during write (Hmax_write ) increased

to 8000 A/m. Revised IDDW typical from110 to 152mA, max from TBD to 180mA; IDDR max from

TBD to 68mA; ISB1 typical from 11 to 9ma; ISB2 from typical 7 to 5mA.

7 Oct 28, 2011 Added note to BGA package option products are MSL-6 only, MSL-3 qualication underway.

Fixed typo on BGA drawing: Top View incorrectly labeled Bottom View.

8 August 6, 2012 Figure 2.1 Power Up and Power Down Timing redrawn. Added 54-TSOP illustrations. Re-

formatted all parametric tables. Reformatted Table 4.1 Ordering Part Numbers.

9 August 27, 2013 Corrected the AEC Q-100 Grade A ordering option to be available in 54-TSOP2, not 48-

BGA.

9.1 Jaunary 29,

2014 Corrected minor typo in Ordering PN table.

10 April 25, 2014 AEC-Q100 removed until qualied product is available.

11 September 17,

2014 48-BGA package options moisture sensitivity level upgraded to MSL-5.

11.1 May 19, 2015 Revised Everspin contact information.

11.2 June 11, 2015 Corrected Japan Sales Oce telephone number.

11.3 July 29, 2015 Minor correction to the ‘ddd’ tolerance value for the BGA Package (Note 4.)

11.4 March 11, 2016 The BGA package moisture sensitivity level rating is changed to MSL-6 in Table 4.1.

11.5 November 22,

2016 The BGA package moisture sensitivity level rating is changed to MSL-5 in Table 4.1.

11.6 May 09, 2017 All products meet MSL-3 moisture sensitivity level

11.7 March 23, 2018 Updated the Contact Us table

6. REVISION HISTORY

Everspin Technologies, Inc.

Information in this document is provided solely to enable system and software

implementers to use Everspin Technologies products. There are no express or

implied licenses granted hereunder to design or fabricate any integrated cir-

cuit or circuits based on the information in this document. Everspin Technolo-

gies reserves the right to make changes without further notice to any products

herein. Everspin makes no warranty, representation or guarantee regarding

the suitability of its products for any particular purpose, nor does Everspin

Technologies assume any liability arising out of the application or use of any

product or circuit, and specically disclaims any and all liability, including

without limitation consequential or incidental damages. “Typical” parameters,

which may be provided in Everspin Technologies data sheets and/or speci-

cations can and do vary in dierent applications and actual performance

may vary over time. All operating parameters including “Typicals” must be

validated for each customer application by customer’s technical experts. Ever-

spin Technologies does not convey any license under its patent rights nor the

rights of others. Everspin Technologies products are not designed, intended,

or authorized for use as components in systems intended for surgical implant

into the body, or other applications intended to support or sustain life, or for

any other application in which the failure of the Everspin Technologies product

could create a situation where personal injury or death may occur. Should

Buyer purchase or use Everspin Technologies products for any such unintended

or unauthorized application, Buyer shall indemnify and hold Everspin Tech-

nologies and its ocers, employees, subsidiaries, aliates, and distributors

harmless against all claims, costs, damages, and expenses, and reasonable

attorney fees arising out of, directly or indirectly, any claim of personal injury

or death associated with such unintended or unauthorized use, even if such

claim alleges that Everspin Technologies was negligent regarding the design

or manufacture of the part. Everspin™ and the Everspin logo are trademarks of

Everspin Technologies, Inc. All other product or service names are the property

of their respective owners.

7. HOW TO CONTACT US

How to Reach Us:

Home Page:

www.everspin.com

World Wide Information Request

WW Headquarters - Chandler, AZ

5670 W. Chandler Blvd., Suite 100

Chandler, Arizona 85226

Tel: +1-877-480-MRAM (6726)

Local Tel: +1-480-347-1111

Fax: +1-480-347-1175

support@everspin.com

orders@everspin.com

sales@everspin.com

Europe, Middle East and Africa

Everspin Europe Support

support.europe@everspin.com

Japan

Everspin Japan Support

support.japan@everspin.com

Asia Pacic

Everspin Asia Support

support.asia@everspin.com

Filename:

EST00352_MR4A16B_Datasheet_Rev11.7 032318