Dual USB Port Power Supply Controller ISL6185 Features The ISL6185 USB power controller family provides fully independent overcurrent (OC) fault protection for two or more USB ports. * 2.5V to 5V Operating Range This product family consists of sixteen individual functional product variants and three package options. It is operation rated for a nominal +2.5V to +5V range and is specified over the full commercial and industrial temperature ranges. Each ISL6185 type incorporates in a single package two 71m P-channel MOSFET power switches for power control. Each features internal current monitoring, accurate current limiting, and current limited delay to turn-off, for system supply protection along with control and communication I/O. The ISL6185 family offers product variants with specified continuous output current levels of 0.6A, 1.1A, 1.5A or 1.8A; enable active high or low inputs; and latch off or automatic retry after overcurrent turn-off, making these devices well suited for many low-power applications. This family of ICs is offered in an industry-standard SOIC pinout and also in the 70% smaller 3x3 DFN packages providing similar or enhanced performance in the smallest possible package. * 71m Integrated Power P-channel MOSFET Switches * Continuous Current Options for 0.6A, 1.1A, 1.5A and 1.8A * Thermally Insensitive 12ms of Current Limiting Prior to Turn-Off * Output Discharges with Reverse Current Blocking When Disabled * Latch-off or Auto Restart Options * 1A Off-State Supply Current * Enable Polarity Options * Industry-standard Pin for Pin SOIC, and Smaller DFN Packages Available * UL Recognized, File Number: E333469 Applications * USB 1, 2, 3 Port Power Management * Low Power (18W) Electronic Circuit Limiting and Breaker D+ D- C O N T R O L L E R ENABLE_1 USB PORT 1 OUT_1 VBUS FAULT_1 +5V VIN GND ISL6185 FAULT_2 ENABLE_2 OUT_2 D+ DUSB PORT POWER FIGURE 1. TYPICAL APPLICATION March 8, 2012 FN6937.3 1 VBUS USB PORT_2 1.3 NORMALIZED rDS(ON) U S B 1.2 1.1 1.0 0.9 0.8 0.7 -40 -25 0 25 45 75 TEMPERATURE (C) 85 115 FIGURE 2. NORMALIZED rDS(ON) TEMPERATURE CHARACTERISTIC CURVE CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2010, 2011, 2012. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. ISL6185 Simplified Block Diagram CHANNEL 1 LIKE CHANNEL 2 FAULT_1 GND + -V comp OUT_1 VIN POR CURRENT AND TEMP. MONITORING, GATE, DELAY & OUTPUT CONTROL LOGIC EN_1 EN_2 OUT_2 FAULT_2 Ordering Information PART NUMBER (Notes 1, 2, 3) PART MARKING EN/EN INPUT VIN = 5V MAXIMUM CONTINUOUS IOUT (A) LATCH/AUTO RETRY TEMP. RANGE (C) PACKAGE (Pb-free) PKG. DWG. # ISL61851ACBZ 61851A CBZ EN 0.6 LATCH 0 to +70 8 Lead SOIC M8.15 ISL61851BCBZ 61851B CBZ EN 0.6 RETRY 0 to +70 8 Lead SOIC M8.15 ISL61851CCBZ 61851C CBZ EN 1.1 LATCH 0 to +70 8 Lead SOIC M8.15 ISL61851DCBZ 61851D CBZ EN 1.1 RETRY 0 to +70 8 Lead SOIC M8.15 ISL61851ECBZ 61851E CBZ EN 0.6 LATCH 0 to +70 8 Lead SOIC M8.15 ISL61851FCBZ 61851F CBZ EN 0.6 RETRY 0 to +70 8 Lead SOIC M8.15 ISL61851GCBZ 61851G CBZ EN 1.1 LATCH 0 to +70 8 Lead SOIC M8.15 ISL61851HCBZ 61851H CBZ EN 1.1 RETRY 0 to +70 8 Lead SOIC M8.15 ISL61851ICBZ 61851I CBZ EN 1.5 LATCH 0 to +70 8 Lead SOIC M8.15 ISL61851JCBZ 61851J CBZ EN 1.5 RETRY 0 to +70 8 Lead SOIC M8.15 ISL61851KCBZ 61851K CBZ EN 1.5 LATCH 0 to +70 8 Lead SOIC M8.15 ISL61851LCBZ 61851L CBZ EN 1.5 RETRY 0 to +70 8 Lead SOIC M8.15 ISL61852ACRZ 52AC EN 0.6 LATCH 0 to +70 8 Lead DFN L8.3x3J ISL61852BCRZ 52BC EN 0.6 RETRY 0 to +70 8 Lead DFN L8.3x3J ISL61852CCRZ 52CC EN 1.1 LATCH 0 to +70 8 Lead DFN L8.3x3J ISL61852DCRZ 52DC EN 1.1 RETRY 0 to +70 8 Lead DFN L8.3x3J ISL61852ECRZ 52EC EN 0.6 LATCH 0 to +70 8 Lead DFN L8.3x3J 2 FN6937.3 March 8, 2012 ISL6185 Ordering Information (Continued) PART NUMBER (Notes 1, 2, 3) ISL61852FCRZ PART MARKING 52FC EN/EN INPUT VIN = 5V MAXIMUM CONTINUOUS IOUT (A) LATCH/AUTO RETRY TEMP. RANGE (C) EN 0.6 RETRY 0 to +70 8 Lead DFN L8.3x3J PACKAGE (Pb-free) PKG. DWG. # ISL61852GCRZ 52GC EN 1.1 LATCH 0 to +70 8 Lead DFN L8.3x3J ISL61852HCRZ 52HC EN 1.1 RETRY 0 to +70 8 Lead DFN L8.3x3J ISL61852ICRZ 52IC EN 1.5 LATCH 0 to +70 8 Lead DFN L8.3x3J ISL61852JCRZ 52JC EN 1.5 RETRY 0 to +70 8 Lead DFN L8.3x3J ISL61852KCRZ 52KC EN 1.5 LATCH 0 to +70 8 Lead DFN L8.3x3J ISL61852LCRZ 52LC EN 1.5 RETRY 0 to +70 8 Lead DFN L8.3x3J ISL61853ACRZ 53AC EN 0.6 LATCH 0 to +70 10 Lead DFN L10.3x3 ISL61853BCRZ 53BC EN 0.6 RETRY 0 to +70 10 Lead DFN L10.3x3 ISL61853CCRZ 53CC EN 1.1 LATCH 0 to +70 10 Lead DFN L10.3x3 ISL61853DCRZ 53DC EN 1.1 RETRY 0 to +70 10 Lead DFN L10.3x3 ISL61853ECRZ 53EC EN 0.6 LATCH 0 to +70 10 Lead DFN L10.3x3 ISL61853FCRZ 53FC EN 0.6 RETRY 0 to +70 10 Lead DFN L10.3x3 ISL61853GCRZ 53GC EN 1.1 LATCH 0 to +70 10 Lead DFN L10.3x3 ISL61853HCRZ 53HC EN 1.1 RETRY 0 to +70 10 Lead DFN L10.3x3 ISL61853ICRZ 53IC EN 1.5 LATCH 0 to +70 10 Lead DFN L10.3x3 ISL61853JCRZ 53JC EN 1.5 RETRY 0 to +70 10 Lead DFN L10.3x3 ISL61853KCRZ 53KC EN 1.5 LATCH 0 to +70 10 Lead DFN L10.3x3 ISL61853LCRZ 53LC EN 1.5 RETRY 0 to +70 10 Lead DFN L10.3x3 ISL61853MCRZ 53MC EN 1.8 LATCH 0 to +70 10 Lead DFN L10.3x3 ISL61853NCRZ 53NC EN 1.8 RETRY 0 to +70 10 Lead DFN L10.3x3 ISL61853OCRZ 53OC EN 1.8 LATCH 0 to +70 10 Lead DFN L10.3x3 ISL61853PCRZ 53PC EN 1.8 RETRY 0 to +70 10 Lead DFN L10.3x3 ISL61851AIBZ 61851A IBZ EN 0.6 LATCH -40 to +85 8 Lead SOIC M8.15 ISL61851BIBZ 61851B IBZ EN 0.6 RETRY -40 to +85 8 Lead SOIC M8.15 ISL61851CIBZ 61851C IBZ EN 1.1 LATCH -40 to +85 8 Lead SOIC M8.15 ISL61851DIBZ 61851D IBZ EN 1.1 RETRY -40 to +85 8 Lead SOIC M8.15 ISL61851EIBZ 61851E IBZ EN 0.6 LATCH -40 to +85 8 Lead SOIC M8.15 ISL61851FIBZ 61851F IBZ EN 0.6 RETRY -40 to +85 8 Lead SOIC M8.15 ISL61851GIBZ 61851G IBZ EN 1.1 LATCH -40 to +85 8 Lead SOIC M8.15 ISL61851HIBZ 61851H IBZ EN 1.1 RETRY -40 to +85 8 Lead SOIC M8.15 ISL61851IIBZ 61851I IBZ EN 1.5 LATCH -40 to +85 8 Lead SOIC M8.15 ISL61851JIBZ 61851J IBZ EN 1.5 RETRY -40 to +85 8 Lead SOIC M8.15 ISL61851KIBZ 61851K IBZ EN 1.5 LATCH -40 to +85 8 Lead SOIC M8.15 ISL61851LIBZ 61851L IBZ EN 1.5 RETRY -40 to +85 8 Lead SOIC M8.15 ISL61852AIRZ 52AI EN 0.6 LATCH -40 to +85 8 Lead DFN L8.3x3J ISL61852BIRZ 52BI EN 0.6 RETRY -40 to +85 8 Lead DFN L8.3x3J ISL61852CIRZ 52CI EN 1.1 LATCH -40 to +85 8 Lead DFN L8.3x3J ISL61852DIRZ 52DI EN 1.1 RETRY -40 to +85 8 Lead DFN L8.3x3J ISL61852EIRZ 52EI EN 0.6 LATCH -40 to +85 8 Lead DFN L8.3x3J 3 FN6937.3 March 8, 2012 ISL6185 Ordering Information (Continued) PART NUMBER (Notes 1, 2, 3) ISL61852FIRZ EN/EN INPUT VIN = 5V MAXIMUM CONTINUOUS IOUT (A) LATCH/AUTO RETRY TEMP. RANGE (C) 52FI EN 0.6 RETRY -40 to +85 8 Lead DFN L8.3x3J PART MARKING PACKAGE (Pb-free) PKG. DWG. # ISL61852GIRZ 52GI EN 1.1 LATCH -40 to +85 8 Lead DFN L8.3x3J ISL61852HIRZ 52HI EN 1.1 RETRY -40 to +85 8 Lead DFN L8.3x3J ISL61852IIRZ 52II EN 1.5 LATCH -40 to +85 8 Lead DFN L8.3x3J ISL61852JIRZ 52JI EN 1.5 RETRY -40 to +85 8 Lead DFN L8.3x3J ISL61852KIRZ 52KI EN 1.5 LATCH -40 to +85 8 Lead DFN L8.3x3J ISL61852LIRZ 52LI EN 1.5 RETRY -40 to +85 8 Lead DFN L8.3x3J ISL61853AIRZ 53AI EN 0.6 LATCH -40 to +85 10 Lead DFN L10.3x3 ISL61853BIRZ 53BI EN 0.6 RETRY -40 to +85 10 Lead DFN L10.3x3 ISL61853CIRZ 53CI EN 1.1 LATCH -40 to +85 10 Lead DFN L10.3x3 ISL61853DIRZ 53DI EN 1.1 RETRY -40 to +85 10 Lead DFN L10.3x3 ISL61853EIRZ 53EI EN 0.6 LATCH -40 to +85 10 Lead DFN L10.3x3 ISL61853FIRZ 53FI EN 0.6 RETRY -40 to +85 10 Lead DFN L10.3x3 ISL61853GIRZ 53GI EN 1.1 LATCH -40 to +85 10 Lead DFN L10.3x3 ISL61853HIRZ 53HI EN 1.1 RETRY -40 to +85 10 Lead DFN L10.3x3 ISL61853IIRZ 53II EN 1.5 LATCH -40 to +85 10 Lead DFN L10.3x3 ISL61853JIRZ 53JI EN 1.5 RETRY -40 to +85 10 Lead DFN L10.3x3 ISL61853KIRZ 53KI EN 1.5 LATCH -40 to +85 10 Lead DFN L10.3x3 ISL61853LIRZ 53LI EN 1.5 RETRY -40 to +85 10 Lead DFN L10.3x3 ISL61853MIRZ 53MI EN 1.8 LATCH -40 to +85 10 Lead DFN L10.3x3 ISL61853NIRZ 53NI EN 1.8 RETRY -40 to +85 10 Lead DFN L10.3x3 ISL61853OIRZ 53OI EN 1.8 LATCH -40 to +85 10 Lead DFN L10.3x3 ISL61853PIRZ 53PI EN 1.8 RETRY -40 to +85 10 Lead DFN L10.3x3 ISL61851EVAL1Z 8 Lead SOIC Evaluation Platform with ISL61851A installed ISL61852EVAL1Z 8 Lead DFN Evaluation Platform with ISL61852H installed ISL61853EVAL1Z 10 Lead DFN Evaluation Platform with ISL61853I installed NOTES: 1. Add "-T*" suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pbfree products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information pages for ISL6185XXC (commercial version) and ISL6185XXI (industrial version). For more information on MSL please see techbrief TB363. 4 FN6937.3 March 8, 2012 ISL6185 Pin Configurations ISL6185 (10 LD DFN) TOP VIEW ISL6185 (8 LD SOIC/DFN) TOP VIEW GND 1 VIN 2 EN1/EN1 EN2/EN2 3 (GND) EPAD DFN Only 4 GND 1 VIN 2 VIN 3 8 FLT1 7 OUT1 OUT2 EN1/EN1 4 6 5 EN2/EN2 5 (GND) EPAD 10 FLT1 9 OUT1 8 NC 7 OUT2 6 FLT2 FLT2 Pin Descriptions PIN NUMBER 8 Ld SOIC/DFN 10 Ld DFN SYMBOL 1 1 GND IC ground reference. 2 2, 3 VIN Chip bias, Controlled Voltage Input, Undervoltage Lock Out (UVLO). VIN provides chip bias voltage. At VIN < 1.7V chip functionality is disabled, FLT is active and floating, and OUT is held low. Range 0V to 5.5V. 3, 4 4, 5 EN1, EN1/ EN2, EN2 Enable/Disable inputs, Active high (EN) and active low (EN) options enable the power switch. These inputs have internal 1M pull-off resistors. Range 0V to VIN. 5, 8 6, 10 FLT2 FLT1 Overcurrent Fault Indicator. FLT floats and is disabled until VIN >VUVLO. This output is pulled low after the current limit time-out period has expired. Fault is not signaled due to over-temperature shut down. Range 0V to VIN. 6, 7 7, 9 OUT2, OUT1 Controlled Supply Output. Upon an OC condition, IOUT is current limited. Current limit response time is within 200s. This output remains in current limit for a nominal 12ms before being turned off either for the latch or auto retry versions. Range 0V to VIN. - 8 NC PD (DFN only) PD EPAD 5 DESCRIPTION This pin is not electrically connected internally. Thermal Dissipation Exposed PAD Range: Connect to GND. FN6937.3 March 8, 2012 ISL6185 Absolute Maximum Ratings Thermal Information Supply Voltage (VIN to GND, Note 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.5V EN, FAULT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VIN OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to VIN 0.3V Output Current . . . . . . . . . . . Short Circuit Protected Current Limit of 2.5A ESD Rating Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . . . . . . . 3kV Machine Model (Per MIL-STD-883 Method 3015.7) . . . . . . . . . . . . 300V Latch Up (Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . . . . . 100mA Thermal Resistance (Typical, Note 4) JA (C/W) JC (C/W) 8 Lead SOIC Package (Note 4) . . . . . . . . . . 120 N/A 8 Lead 3x3 DFN Package (Notes 5, 6) . . . 48 6 10 Lead 3x3 DFN Package (Notes 5, 6) . . 53 6 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +150C Maximum Storage Temperature Range . . . . . . . . . . . . . . -65C to +150C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Commercial Temperature Range . . . . . . . . . . . . . . . . . . . . . . 0C to +70C Industrial Temperature Range . . . . . . . . . . . . . . . . . . . . . . . -40C to +85C Supply Voltage Range (Typical). . . . . . . . . . . . . . . . . . . . . . . . . 2.3V to 5.5V CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 5. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with "direct attach" features. See Tech Brief TB379. 6. For JC, the "case temp" location is the center of the exposed metal pad on the package underside. 7. All voltages are relative to GND, unless otherwise specified. Electrical Specifications range, 0C to +75C or -40C to +85C. SYMBOL VIN = 5V, TA = TJ, Unless Otherwise Specified. Boldface limits apply over the operating temperature PARAMETER TEST CONDITIONS MIN (Note 8) TYP MAX (Note 8) UNITS - 71 87 m 110 m 105 m POWER SWITCH rDS(ON)_50 ON-Resistance at 5.0V (Pulse Tested) VIN = 5V, IOUT = 0.1A, TA = TJ = +25C TA = TJ = +85C rDS(ON)_33 ON-Resistance at 3.3V (Pulse Tested) VIN = 3.3V, IOUT = 0.1A, TA = TJ = +25C rDS(ON)_25 On Resistance at 2.5V (Pulse Tested) VIN = 2.5V, IOUT = 0.1A, TA = TJ = +25C TA = TJ = +85C - 90 - TA = TJ = +85C - 114 130 m 127 m 150 m VOUT_DIS Disabled Output Voltage VIN = 5V, Switch Disabled, 50A Load - 50 70 mV ROUT_PU Output Pull-Down Resistor VIN = 5V, Switch Disabled 8 9.6 12 k tR VOUT Rise Time RL = 10, CL = 10F, 10% to 90% - 100 - s tF Slow VOUT Turn-off Fall Time RL = 10, CL = 10F, 90% to 10% - 200 - s tF_fast Fast VOUT Turn-off Fall Time RL = 1, CL = 10F, 80% to 20% - 23 - s ISL6185xA,B,E,F - 0.6 A ISL6185xC,D,G,H - 1.1 A ISL6185xI,J,K,L - 1.5 A ISL61853M,N,O,P (10 Ld DFN) - 1.8 A ISL6185xA,B,E,F - 0.6 A ISL6185xC,D,G,H - 0.9 A ISL61851I,J,K,L (SOIC) - 1.3 A ISL61852, ISL61853 (DFN) - 1.5 A CURRENT CONTROL IOUT_CONT_5 IOUT_CONT_5 IOUT_CONT_5 Maximum Continuous Current, VIN = 5V. Guaranteed by Itrip minimum specification. IOUT_CONT_5 IOUT_CONT_3 IOUT_CONT_3 IOUT_CONT_3 Maximum Continuous Current, VIN = 3.3V. Guaranteed by Itrip minimum specification. IOUT_CONT_3 6 FN6937.3 March 8, 2012 ISL6185 Electrical Specifications VIN = 5V, TA = TJ, Unless Otherwise Specified. Boldface limits apply over the operating temperature range, 0C to +75C or -40C to +85C. (Continued) MIN (Note 8) TYP MAX (Note 8) UNITS ISL6185xA,B,E,F - 0.6 - A ISL61851C,D,G,H,I,J,K,L (SOIC) - 0.9 - A IOUT_CONT_2 ISL61852, ISL61853 C,D,G,H (DFN) - 1 - A IOUT_CONT_2 ISL61853I,J,K,L (10 Ld DFN) - 1 - A SYMBOL PARAMETER IOUT_CONT_2 Maximum Continuous Current, VIN = 2.5V IOUT_CONT_2 TEST CONDITIONS - 1 - A ISL6185xA,B,E,F ISL61853M,N,O,P (10 Ld DFN) 0.70 1.02 1.52 A ITRIP_5 ISL6185xC,D,G,H 1.15 1.45 1.95 A ITRIP_5 ISL6185xI,J,K,L 1.55 1.82 2.25 A ITRIP_5 ISL61853M.N,O,P 1.85 1.99 2.45 A IOUT_CONT_2 ITRIP_5 Trip Current, VIN = 5V ISL6185xA,B,E,F 0.65 0.86 1.20 A ITRIP_3 ISL6185xC,D,G,H 0.95 1.25 1.60 A ITRIP_3 ISL6185xI,J,K,L 1.35 1.60 1.85 A ITRIP_3 ISL61853M.N,O,P 1.55 1.89 2.25 A ISL6185xA,B,E,F - 0.65 - A ITRIP_2 ISL6185xC,D,G,H - 1 - A ITRIP_2 ISL6185xI,J,K,L - 1.2 - A ITRIP_2 ISL61853M.N,O,P - 1.6 - A ISL6185xA,B,E,F, VIN - VOUT = 1V 0.50 0.65 0.78 A ILIM_5 ISL6185xC,D,G,H, VIN - VOUT = 1V 0.98 1.14 1.28 A ILIM_5 ISL6185xI,J,K,L, VIN - VOUT = 1V 1.30 1.55 1.72 A ITRIP_3 ITRIP_2 ILIM_5 Trip Current, VIN = 3.3V Trip Current, VIN = 2.5V Current Limit, VIN = 5V ISL61853M,N,O,P, VIN - VOUT = 1V 1.52 1.83 2.20 A ISL6185xA,B,E,F, VIN - VOUT = 1V 0.45 0.63 0.75 A ILIM_3 ISL6185xC,D,G,H, VIN - VOUT = 1V 0.90 1.10 1.26 A ILIM_3 ISL6185xI,J,K,L, VIN - VOUT = 1V 1.25 1.50 1.68 A ILIM_3 ISL61853M,N,O,P, VIN - VOUT = 1V 1.48 1.78 2.05 A ILIM_5 ILIM_3 Current Limit, VIN = 3.3V ISL6185xA,B,E,F, VIN - VOUT = 1V 0.47 0.61 0.74 A ILIM_2 ISL6185xC,D,G,H, VIN - VOUT = 1V 0.90 1.05 1.17 A ILIM_2 ISL6185xI,J,K,L, VIN - VOUT = 1V 1.15 1.37 1.58 A ILIM_2 ISL61853M,N,O,P, VIN - VOUT = 1V 1.3 1.63 1.90 A ISL6185xA,B,E,F, VOUT = 0V 0.60 0.80 1.00 A ILIM_2 Isc_5 Current Limit, VIN = 2.5V Short Circuit Current, VIN = 5V Isc_5 ISL6185xC,D,G,H, VOUT = 0V 1.00 1.27 1.55 A Isc_5 ISL6185xI,J,K,L, VOUT = 0V 1.15 1.61 1.85 A Isc_5 ISL61853M,N,O,P, VOUT = 0V 1.20 1.70 2.5 A ISL6185XA,B,E,F, VOUT = 0V 0.35 0.48 0.60 A Isc_3 ISL6185XC,D,G,H, VOUT = 0V 0.65 0.80 0.95 A Isc_3 ISL6185xI,J,K,L, VOUT = 0V 0.70 1.06 1.25 A Isc_3 ISL61853M,N,O,P, VOUT = 0V 0.90 1.24 1.50 A Isc_3 Short Circuit Current, VIN = 3.3V 7 FN6937.3 March 8, 2012 ISL6185 Electrical Specifications VIN = 5V, TA = TJ, Unless Otherwise Specified. Boldface limits apply over the operating temperature range, 0C to +75C or -40C to +85C. (Continued) MIN (Note 8) TYP ISL6185xA,B,E,F, VOUT = 0V - 0.61 Isc_2 ISL6185xC,D,G,H, VOUT = 0V - 1.06 - A Isc_2 ISL6185xI,J,K,L, VOUT = 0V - 1.30 - A Isc_2 ISL61853M,N,O,P, VOUT = 0V - 1.39 - A SYMBOL Isc_2 PARAMETER Short Circuit Current, VIN = 2.5V TEST CONDITIONS MAX (Note 8) UNITS A Isc_5.5 Short Circuit Current, VIN = 5.5V All ISL6185X Variants - - 2.5 A tsettIlim OC to Limit Settling Time VIN/RL = 2ILIM, CL = 10F to within 10% of ILIM - 200 - s Severe OC to Limit Settling Time VIN/RL = 4ILIM, CL = 10F to within 10% of ILIM - 30 - s tCL Current Limit Duration IOUT = ILIM 9.2 12 15 ms tRTY Automatic Retry Period 0.80 1 1.35 s - - 0.4 V - 5 - A tsettIlim_sev I/O PARAMETERS Vfault_lo Ifault Fault Output Voltage Fault IOUT = 10mA Fault Leakage EN / EN Rising Threshold VIN = 5V 1.5 1.8 2 V EN / EN Rising Threshold Hysteresis VIN = 5V 80 140 175 mV EN / EN Rising Threshold VIN = 3.3V 1.0 1.3 1.6 V EN / EN Rising Threshold Hysteresis VIN = 3.3V 58 80 120 mV EN / EN Rising Threshold VIN = 2.5V 0.95 1.1 1.3 V EN / EN Rising Threshold Hysteresis VIN = 2.5V 30 70 110 mV Ren_h ENABLE Pull-Down Resistor Enable asserted high options 0.6 1 1.55 M Ren_l ENABLE Pull-Up Resistor Enable asserted low options 0.6 1 1.55 M Venr_5 Hys_Venr_5 Venr_3 Hys_Venr_3 Venr_2 Hys_Venr_2 tON Enable to Output Turn-on Time RL = 10, CL = 10F, Enable 50% to Output 90% - 0.1 - ms tOFF Enable to Output Turn-off Time RL = 10, CL = 10F, Enable 50% to Output 10% - 0.25 - ms 50 75 A BIAS PARAMETERS IVDD Enabled VIN Current Switches Closed, OUTPUT = OPEN IVDD Disabled VIN Current Switches Open, OUTPUT = OPEN - 2 5 A VUVLO Rising POR Threshold VIN Rising to functional operation 1.7 2.1 2.3 V Reverse Blocking Leakage Current VIN = 0V, VOUT = 5V 2 A Temp_dis Over-Temperature Disable - 150 - C Temp_hys Over-Temperature Hysteresis - 20 - C IVR - NOTE: 8. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. 8 FN6937.3 March 8, 2012 ISL6185 Introduction Functional Description The ISL6185 is a dual channel fully independent overcurrent (OC) fault protection IC for the +2.5V to +5V environment. Each ISL6185 incorporates in a single package two 85m P-channel MOSFET power switches for power control. Independent enabling inputs and fault reporting outputs compatible with 2.5V to 5V logic allow for external control and reporting. This device features integrated power switches with current monitoring, accurate current limiting, reverse bias protection and current limited timed delay to turn-off for system reliability. See Figures 13 through 28 for typical operational waveforms including both under-current and over-current situations. Power On Preset (POR) The ISL6185 offers current sense and limiting, with VIN = 5V guaranteed continuous current product variants of 0.6A, 1.1A, 1.5A and 1.8A, making these devices well suited for a myriad of USB and other low power (9W max) port power management applications and configurations. Upon enable, the switch passes a constant current to the load. The voltage on the VOUT pin ramps up according the equation, ILIM/COUT (V/s). Resistive or active load slows the VOUT ramp-up toward the top of its curve. The ISL6185 also provides thermally insensitive timed OC turn-off and fault notification. This isolates and protects the voltage bus in the event of a peripheral OC event or short circuit event, independent of the adjoining switch's electrical or the ambient thermal condition. The ISL6185 undervoltage lockout feature prevents turn-on of the outputs unless the correct ENABLE state and VIN > VUVLO are present. During initial turn-on, the ISL6185 prevents fault reporting by blanking the fault signal. During operation, once an OC condition is detected, the output is current limited for tCL to allow transient OC conditions to pass. If still in current limit after the current limit period has elapsed, the output is turned off, and the fault is reported by pulling the corresponding FAULT output low. On the latch-off options, after turn-off, both the output and the FAULT signal are latched low until reset by the enable signal being de-asserted or until a POR occurs. At this time, the FAULT signal clears, and the switch is ready to be turned back on. On the auto restart options, the ISL6185 attempts to periodically turn on the output, as long as the enable is asserted. When disabled, the ISL6185 has a low quiescent supply current and an output-to-input reverse current flow blocking capability. The ISL6185 family is provided with enable polarity options and an industry-standard 8 lead SOIC pinout, along with two versions in the 70% smaller 3x3 DFN. The 8 Ld DFN package offers the same performance as the 8 Ld SOIC, whereas the 10 Ld DFN offers higher current capability in the smallest possible package because of lower package electrical and thermal resistance. 9 The ISL6185 POR feature inhibits device functionality when VIN < VUVLO. Reverse Polarity Protection In any event in which the power switch is disabled and VOUT > VIN, there will be no output-to-input current flow, nor will the output voltage appear on the input. Soft-Start Fault Blanking On Start-Up During initial turn-on, the ISL6185 prevents nuisance faults from being reported to the system controller by blanking the fault signal until the internal FET is fully enhanced. Current Trip and Limiting Levels The ISL6185 provides integrated current sensing in the MOSFET that allows for rapid control of OC events. Once an OC condition is detected, the ISL6185 goes into its current limiting (CL) control mode. The ISL6185 is variant specified to allow a continuous current (ICONT) operation of 0.6A, 1.1A, 1.5A or 1.8A. As the current increases past its continuous current rating, it will reach a level that causes the device to enter its current limit mode; that is, the current trip level. The current trip level is in all cases adequately above the ICONT rating so as not to cause unintended false faults. The current limit is specified at VOUT = VIN - 1V to test a known representative condition and is featured at a nominal value slightly higher than the continuous current rating. The speed of this current limiting control is inversely related to the magnitude of the OC fault. Thus, a hard overcurrent is more quickly pulled to its limiting value than a marginal OC condition. Over-Temperature Shutdown Although the ISL6185 has an over-temperature shutdown and lockout feature, because of the 12ms timed shutdown, the thermal shutdown is likely to be invoked only in extremely high ambient temperatures. The over-temperature protection invokes and disables the switch turn-on operation once the die temperature is ~+140C. It turns off an already on switch at ~+150C and releases the part to operation once the die temperature falls to ~+120C. FN6937.3 March 8, 2012 ISL6185 Turn-off Time Delay Latch-off Restart/Auto-Restart Start During operation, once an OC condition is detected, the output is current limited for ~12ms to allow transient OC conditions to pass. If still in current limit and after the current limit period has elapsed, the output is turned off, and the fault is reported by pulling the corresponding FAULT low. The internal 12ms timer starts upon current limiting and is independent of ambient or IC thermal conditions, thus providing more consistent operation over the entire temperature range. After turn-off, with the latch-off options, both the output and the FAULT signal are latched low until they are reset by the enable signal being de-asserted. At this time, the FAULT signal clears, and the IC is ready for enable to assert. On the auto restart options, the ISL6185 attempts to periodically turn-on the output at approximately 1s intervals, as long as the enable is asserted. If the OC condition remains indefinitely, the fault indication and the restart attempts also continue until the thermal protection feature is invoked, thus increasing the restart period. Active Output Pull-down Another ISL6185 feature is the 10k active pull-down on the outputs to <60mV above GND when the device is disabled, thus ensuring discharge of the load. Typical Performance Curves 150 1.3 rDS(ON) @ 0.5A (m) 130 VIN = 2.5V 120 110 100 VIN = 3.3V 90 80 VIN = 5V 70 NORMALIZED rDS(ON) 140 1.1 1.0 0.9 0.8 60 50 -40 -25 0 25 45 75 TEMPERATURE (C) 85 0.7 115 FIGURE 3. SWITCH ON-RESISTANCE AT 0.5A 1.5 1.0 0.9 3.3V ITRIP 0.8 0.7 0.6 0.5 0.4 -25 0 25 45 75 TEMPERATURE (C) 85 115 1.6 5V ITRIP OUTPUT CURRENT (A) 1.1 -40 FIGURE 4. NORMALIZED SWITCH RESISTANCE 1.2 OUTPUT CURRENT (A) 1.2 5V ISC 5V ILIM 3.3V ILIM -25 0 25 45 75 TEMPERATURE (C) 85 115 FIGURE 5. 0.6A CONTINUOUS CURRENT CHARACTERISTICS 10 1.3 1.2 1.1 5V ITRIP 5V ISC 3.3V ITRIP 5V ILIM 1.0 3.3V ILIM 0.9 0.8 3.3V ISC 0.7 3.3V ISC -40 1.4 0.6 -40 -25 0 25 45 75 TEMPERATURE (C) 85 115 FIGURE 6. 1.1A CONTINUOUS CURRENT CHARACTERISTICS FN6937.3 March 8, 2012 ISL6185 (Continued) 2.0 2.2 1.8 5V ITRIP 2.0 1.6 1.4 3.3V ITRIP OUTPUT CURRENT (A) OUTPUT CURRENT (A) Typical Performance Curves 5V ISC 5V ILIM 3.3V ILIM 1.2 3.3V ISC 1.0 0.8 -40 -25 0 25 45 75 85 3.3V ITRIP 1.8 1.6 3.3V ILIM 3.3V ISC 1.2 -40 -25 TEMPERATURE (C) FIGURE 7. 1.5A CONTINUOUS CURRENT CHARACTERISTICS 0.75 TYPICAL 0.60 -3 SIGMA 0.55 0.50 115 +3 SIGMA 1.15 TYPICAL 1.10 -3 SIGMA 1.05 -40 -25 0 25 45 75 TEMPERATURE (C) 85 1.00 115 FIGURE 9. LIMITING CURRENT 3 SIGMA, VIN = 5V 1.65 2.00 1.50 -3 SIGMA 1.45 1.40 ILIMIT 3 SIGMA TYPICAL -25 0 25 45 75 TEMPERATURE (C) 1.8A CONTINUOUS IOUT VERSION 1.95 +3 SIGMA 1.55 -40 85 115 FIGURE 10. LIMITING CURRENT 3 SIGMA, VIN = 5V 1.5A CONTINUOUS IOUT VERSION 1.60 ILIMIT 3 SIGMA 85 1.1A CONTINUOUS IOUT VERSION 1.20 ILIMIT 3 SIGMA ILIMIT 3 SIGMA 1.25 +3 SIGMA 0.65 0 25 45 75 TEMPERATURE (C) FIGURE 8. 1.8A CONTINUOUS CURRENT CHARACTERISTICS 0.6A CONTINUOUS IOUT VERSION 0.70 5V ISC 5V ILIM 1.4 1.0 115 5V ITRIP +3 SIGMA 1.90 1.85 TYPICAL 1.80 -3 SIGMA 1.75 1.70 1.65 1.35 1.60 -40 -25 0 25 45 75 85 115 TEMPERATURE (C) FIGURE 11. LIMITING CURRENT 3 SIGMA, VIN = 5V 11 -40 -25 0 25 45 75 TEMPERATURE (C) 85 115 FIGURE 12. LIMITING CURRENT 3 SIGMA, VIN = 5V FN6937.3 March 8, 2012 ISL6185 Typical Performance Curves (Continued) ENABLE ENABLE CL = 1F CL = 10F CL = 10F VOUT 1V/DIV CL = 100F CL = 100F VOUT 1V/DIV CL = 1F FIGURE 13. VOUT TURN-ON/RISE TIME vs C LOAD. VIN = 5V, RL = 10 FIGURE 14. VOUT TURN-OFF/FALL TIME vs CLOAD. VIN = 5V, RL = 10 0.6A ICONT VARIANT FLT CL = 10F VOUT 1V/DIV VOUT CL = 100F IIN CL = 1F FIGURE 15. LATCH-OFF vs CLOAD 0.6A ICONT VARIANT FIGURE 16. ILIM WAVEFORM 0.6A ICONT VARIANT 2A OC 27s 6A/ms 0.6A/ms 1A OC 57s 0.08A/ms 0.5A OC 200s 0.72A CURRENT LIMIT 0.53A LOAD CURRENT 0.56A LOAD CURRENT IIN 2A/DIV FIGURE 17. OC RAMP RATE ILIM WAVEFORMS 12 0.66A CURRENT LIMIT FIGURE 18. PEAK CURRENT SETTLING TIMES FN6937.3 March 8, 2012 ISL6185 Typical Performance Curves (Continued) ENABLE ENABLE 0.6A ICONT VARIANT 0.6A ICONT VARIANT VOUT FAULT FAULT IIN LIMITED TO 0.64A IIN VOUT FIGURE 20. TURN-ON INTO MOMENTARY OC FIGURE 19. TURN-ON INTO A SHORT 1.1A ICONT VARIANT FLT VOUT VOUT FLT IIN IIN FIGURE 21. ISL6185 RETRY FUNCTION FIGURE 22. ILIM WAVEFORM ENABLE ENABLE FAULT FAULT VOUT VOUT Iin IIN 1.8A ICONT VARIANT FIGURE 23. VIN = 2.5V TURN-ON INTO 2.2 13 1.8A ICONT VARIANT FIGURE 24. VIN = 5V TURN-ON INTO 2.7 FN6937.3 March 8, 2012 ISL6185 Typical Performance Curves (Continued) CH1 and CH2 ON (3.6A TOTAL IIN) IIN ENABLE FAULT VOUT CH1 ON (1.8A) IIN LIMITED TO 1.7A ENABLE FAULT 1.8A ICONT VARIANT VOUT FIGURE 26. TURN-ON 2ND OUTPUT TO FULL LOAD FIGURE 25. TURN-ON INTO A SHORT 1.1A ICONT VARIANT FLT VOUT VOUT FLT IIN IIN FIGURE 27. ISL6185 RETRY FUNCTION FIGURE 28. ILIM WAVEFORM FIGURE 28. PROPAGATION DELAY AND OUTPUT TRANSITION TIMES Test Circuits + V 10k 10k 5V VIN OUT ISL6185 OUTPUT FLT FLT OUTPUT 10F EN 5V VIN ISL6185 EN 10 OUT 10F 10 RL sized for desired OC level RL rDS(ON) = V/(VOUT/10W) FIGURE 29A. rDS(ON) FIGURE 29B. CURRENT LIMITING FIGURE 29. DC TEST CIRCUIT 14 FN6937.3 March 8, 2012 ISL6185 Test Circuits (Continued) VIN EN 0.5VIN 0.5VIN 10k 0V tON FLT 5V VIN OUTPUT OUT 10F ISL6185 0-VIN OUTPUT EN tOFF VIN 90% 10% GND 10 90% OUTPUT 10% tR FIGURE 30. TRANSIENT TEST CIRCUIT VIN 90% 10% -GND tF FIGURE 31. TRANSIENT WAVEFORM MEASUREMENT POINTS ISL6185xEVAL1Z Schematic and Photo R1 10k AGND C1 V+ 2.2F A AGND V+ EN1 EN2 A A U1 ISL6185 R3 FLT1 OUT1 OUT2 FLT2 10 C2 10F A R4 OUT2 10 C3 R2 FLT1 OUT1 10F A FLT2 10k NOTE: EXPOSED PAD on DFN packages only FIGURE 32A. ISL6185xEVAL SCHEMATIC FIGURE 32B. ISL61851EVAL1Z BOARD PHOTO FIGURE 32. ISL6185xEVAL1Z SCHEMATIC and ISL61851EVAL1Z PHOTOGRAPH 15 FN6937.3 March 8, 2012 ISL6185 Application Information Application Considerations Using the ISL6185xEVAL1Z Platform General and Biasing Information The application considerations for the ISL6185 family are widely accepted best industry practices. Good decoupling practices on the VIN pin must be followed: placement close to the IC, with at least 2.2F recommended. It is recommended to reduce the input and output inductance to the ISL6185 with good PCB layout practices. There are three evaluation platforms for the ISL6185 family. There is one platform for each package style, each with a different continuous output current level and a mix of enable polarity and output retry or latch options. See page 4, at the end of the "Ordering Information" table, for information on the standard available evaluation board options. Figure 32A shows the common schematic for all three evaluation boards. See "Pin Configurations" on page 5 for details and differences. The evaluation platform is biased and monitored through numerous labeled test points. See Table 1 for test point assignments and descriptions. TABLE 1. ISL61851EVAL1Z TEST POINT ASSIGNMENTS TP NAME DESCRIPTION GND Eval Board and IC Gnd V+ Eval Board and IC Bias EN1 Enable Switch 1 EN2 Enable Switch 2 FLT2 Switch 2 Fault OUT2 Switch Out 2 OUT1 Switch Out 1 FLT1 Switch 1 Fault When designing with the 1.5A and 1.8A versions in an implementation in which the output may be unloaded (open) while the ISL6185 is turned on, a minimum of 4.7F of capacitive output load is recommended to prevent high dv/dt from unnecessarily activating the surge/ESD control circuit. The ISL6185 provides several continuous current rated devices specified at VIN = 5V; these are 0.6A, 1.1A, 1.5A and 1.8A options that are capable over the entire temperature extreme. At VIN = 3.3V, the current capability is degraded, and the ISL6185 is specified at 0.6A, 1.1A, 1.3A and 1.5A, respectively. At VIN = 2.5V, there are no minimum specifications, but a typical value is provided for +25C operation (see "Electrical Specifications" on page 6). This degraded capability is due to the higher rDS(ON) of the FET switch at the lower bias voltage. The enhanced thermal characteristics and increased number of bond wires allow the 10 Ld DFN to have a higher current capability than either the 8 Ld SOIC or the DFN. TABLE 2. ISL6185XEVAL1Z BOARD COMPONENT LISTING COMPONENT DESIGNATOR U1 Upon proper bias of the evaluation platform and correct enabling of the IC, the ISL6185 will have a nominal VIN/10 load current that is lower than the continuous current rating passing through each enabled switch. See Figures 13 and 14 for typical ISL6185 turn-on and turn-off waveforms. External current loading in excess of the trip current level for the particular part being evaluated will result in the ISL6185 entering the current limiting mode. Figure 16 illustrates the current limiting mode for the ISL6185 product variants with 0.6A of continuous load current rating. The scope shot shows current limiting for ~12ms before it is turned off and the fault signal is asserted. COMPONENT FUNCTION COMPONENT DESCRIPTION ISL6185 Intersil, ISL6185 R3 - R4 Output Load Resistors 10, 5%, 3W R1 - R2 FLT Output Pull-up Resistor 10k, 0805 Decoupling Capacitor 2.2F, 0805 Load Capacitor 10F 16V Electrolytic, Radial Lead C1 C2 - C3 For additional products, see www.intersil.com/product_tree Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted in the quality certifications found at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 16 FN6937.3 March 8, 2012 ISL6185 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest Rev. DATE REVISION March 1, 2012 FN6937.3 CHANGE In "Features" on page 1 changed from: UL Recognized, File Number: E333469 (Applies to DFN Packages, SOIC Package to be Qualified Shortly) to: UL Recognized, File Number : E333469 In "Absolute Maximum Ratings" on page 6: Changed from: Output Current . . . . . . . . . Short Circuit Protected to: Output Current . . . . . . . . . .Short Circuit Protected Current Limit of 2.5A Updated "Package Outline Drawing" on page 20. Changed Note 1 "1982" to "1994". December 2, 2011 FN6937.2 Page 1: Added "UL Recognized, File Number: E333469 (Applies to DFN packages, SOIC pkg to be qualified shortly)" to "Features" Page 8: Added Isc_5.5, Short Circuit Current with max of 2.5A to "Electrical Specifications" Page 19: Updated package outline drawing to most updated revision. Removed package outline and included center to center distance between lands on recommended land pattern. Removed Note 4 "Dimension b applies to the metallized terminal and is measured between 0.18mm and 0.30mm from the terminal tip." since it is not applicable to this package. Renumbered notes accordingly. June 14, 2011 FN6937.1 Page 2: "Ordering Information": added part numbers of parts installed on evaluation boards to Description column. Page 7: "Electrical Specifications" table: - For "Maximum Continuous Current, VIN = 2.5V," changed "ISL61851C,D,G,H (SOIC)" to "ISL61851C,D,G,H,I,J,K,L (SOIC)" - For "Trip Current, VIN = 5V", changed "ISL61853I,J,K,L" to "ISL6185xI,J,K,L". For "ISL61853M.N,O,P" changed MAX from "2.15" to "2.45". - For "Trip Current, VIN = 3.3V" and "Trip Current, VIN = 2.5V" changed "ISL61853I,J,K,L" to "ISL6185xI,J,K,L". - For "Current Limit, VIN = 5V", "Current Limit, VIN = 3.3V", and "Current Limit, VIN = 2.5V", changed "ISL61853I,J,K,L, VIN - VOUT = 1V" to "ISL6185xI,J,K,L, VIN - VOUT = 1V" - For "Short Circuit Current, VIN = 5V", "Short Circuit Current, VIN = 3.3V" and "Short Circuit Current, VIN = 2.5V" changed "ISL61853I,J,K,L, VOUT = 0V" to "ISL6185xI,J,K,L, VOUT = 0V" Page 8: "Electrical Specifications" table: For the I/O Parameters Venr_5, Hys_Venr_5, Venr_3, Hys_Venr_3, Venr_2, and Hys_Venr_2: changed "ENABLE Rising Threshold" and "ENABLE Rising Threshold Hysteresis" to "EN / EN Rising Threshold" and "EN / EN Rising Threshold Hysteresis," for clarity. Page 8: Electrical Specifications table: Removed UVHYS, POR Hysteresis specification. Page 20: Replaced Rev. 1 of M8.15 package outline drawing, dated 6/05, with Rev 2 (latest version), dated 11/10. Applied current Intersil datasheet template to document. October 22, 2010 FN6937.0 Initial release. Products Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks. Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a complete list of Intersil product families. For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information pages on intersil.com for ISL6185XXC (commercial version) and ISL6185XXI (industrial version). To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff FITs are available from our website at: http://rel.intersil.com/reports/sear 17 FN6937.3 March 8, 2012 ISL6185 Package Outline Drawing L8.3x3J 8 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE Rev 0 9/09 2X 1.950 3.00 B 0.15 8 5 3.00 (4X) 6X 0.65 A 1.64 +0.10/ - 0.15 6 PIN 1 INDEX AREA 4 8X 0.30 8X 0.400 0.10 TOP VIEW 6 PIN #1 INDEX AREA 1 4 0.10 M C A B 2.38 +0.10/ - 0.15 BOTTOM VIEW SEE DETAIL "X" ( 2.38 ) ( 1.95) 0.10 C Max 1.00 C 0.08 C SIDE VIEW ( 8X 0.60) (1.64) ( 2.80 ) PIN 1 C 0 . 2 REF 5 (6x 0.65) 0 . 00 MIN. 0 . 05 MAX. ( 8 X 0.30) DETAIL "X" TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal 0.05 4. Dimension applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. 18 The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. FN6937.3 March 8, 2012 ISL6185 Package Outline Drawing L10.3x3 10 LEAD DUAL FLAT PACKAGE (DFN) Rev 7, 10/11 3.00 5 PIN #1 INDEX AREA A B 1 5 PIN 1 INDEX AREA (4X) 3.00 2.00 8x 0.50 2 10 x 0.23 0.10 1.60 TOP VIEW 10x 0.35 BOTTOM VIEW (4X) 0.10 M C A B 0.415 0.200 0.23 0.35 (10 x 0.55) SEE DETAIL "X" (10x 0.23) 1.00 MAX 0.10 C BASE PLANE 2.00 0.20 C SEATING PLANE 0.08 C SIDE VIEW (8x 0.50) C 0.20 REF 4 1.60 0.05 2.85 TYP TYPICAL RECOMMENDED LAND PATTERN DETAIL "X" NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal 0.05 4. Tiebar shown (if present) is a non-functional feature. 5. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 19 FN6937.3 March 8, 2012 ISL6185 Package Outline Drawing M8.15 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 4, 1/12 DETAIL "A" 1.27 (0.050) 0.40 (0.016) INDEX 6.20 (0.244) 5.80 (0.228) AREA 0.50 (0.20) x 45 0.25 (0.01) 4.00 (0.157) 3.80 (0.150) 1 2 8 0 3 0.25 (0.010) 0.19 (0.008) SIDE VIEW "B" TOP VIEW 2.20 (0.087) SEATING PLANE 5.00 (0.197) 4.80 (0.189) 1.75 (0.069) 1.35 (0.053) 1 8 2 7 0.60 (0.023) 1.27 (0.050) 3 6 4 5 -C- 1.27 (0.050) 0.51(0.020) 0.33(0.013) SIDE VIEW "A 0.25(0.010) 0.10(0.004) 5.20(0.205) TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensioning and tolerancing per ANSI Y14.5M-1994. 2. Package length does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 3. Package width does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 4. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 5. Terminal numbers are shown for reference only. 6. The lead width as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 7. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 8. This outline conforms to JEDEC publication MS-012-AA ISSUE C. 20 FN6937.3 March 8, 2012