2.2x1.4mm SURFACE MOUNT LED LAMP Part Number: AA2214SES/J3-AMT Hyper Red Description Features The Hyper Red device is based on light emitting diode chip z High reliability LED package. made from AlGaInP. z 2.2mm x 1.4mm, 1.3mm high. z Low power consumption. Applications z Available on tape and reel. z Traffic signaling. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. z Backlighting (illuminated advertising , general lighting). z Interior and exterior automotive lighting. z Substitution of micro incandescent lamps. z Reading lamps. z Signal and symbol luminaire for orientation. z Marker lights (e.g. Steps, exit ways, etc). z Decorative and entertainment lighting. Package Dimensions z Indoor and outdoor commercial and residential architectural lighting. Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL4011 REV NO: V.1 DATE: NOV/22/2010 PAGE: 1 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007407 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or damage the internal circuitry. 4. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner diameter of the nozzle should be as large as possible. 5. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup. 6. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup and avoid damage during production. SPEC NO: DSAL4011 REV NO: V.1 DATE: NOV/22/2010 PAGE: 2 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007407 Selection Guide Part No. Dice AA2214SES/J3-AMT Iv (mcd) [2] @ 20mA Lens Type Hyper Red (AlGaInP) Viewing Angle [1] Code. Min. Max. V 1300 1600 W 1600 1900 X 1900 2300 Water Clear 21/2 120 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. Absolute Maximum Ratings at Ta=25C Symbol Value Unit Power dissipation Parameter PD 140 mW Reverse Voltage VR 5 V Junction temperature TJ 120 C Operating Temperature Top -40 To +100 C Storage Temperature Tstg -40 To +120 C IF 50 mA IFM 150 mA 3000 V 350 C/W DC Forward Current[1] Peak Forward Current [2] Electrostatic Discharge Threshold (HBM) Thermal Resistance (Junction/ambient) [1] Rth j-a Notes: 1. Rth(j-a) Results from mounting on PC board FR4 (pad size16 mm 2 per pad), 2. 1/10 Duty Cycle, 0.1ms Pulse Width. Electrical / Optical Characteristics at Ta=25C Parameter Wavelength at peak emission IF=20mA [Typ.] Symbol Value Unit peak 640 nm Dominant Wavelength IF=20mA [Min.] dom [1] 615 nm Dominant Wavelength IF=20mA [Max.] dom [1] 635 nm 25 nm Spectral bandwidth at 50% REL MAX IF=20mA [Typ.] Forward Voltage IF=20mA [Min.] Forward Voltage IF=20mA [Typ.] Forward Voltage IF=20mA [Max.] VF [2] 2.2 V 2.8 Reverse Current (VR = 5V) [Max.] IR 10 uA Temperature coefficient of peak IF=20mA, -10 C T100 C [Typ.] TC peak 0.14 nm/ C Temperature coefficient of dom IF=20mA, -10 C T100 C [Typ.] TC dom 0.04 nm/ C Temperature coefficient of VF IF=20mA, -10 C T100 C [Typ.] TCV -2.0 mV/ C Notes: 1.The dominant Wavelength ( d) above is the setup value of the sorting machine. (Tolerance d : 1nm. ) 2. Forward Voltage: +/-0.1V. SPEC NO: DSAL4011 REV NO: V.1 DATE: NOV/22/2010 PAGE: 3 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007407 Hyper Red AA2214SES/J3-AMT SPEC NO: DSAL4011 REV NO: V.1 DATE: NOV/22/2010 PAGE: 4 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007407 AA2214SES/J3-AMT Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAL4011 REV NO: V.1 DATE: NOV/22/2010 PAGE: 5 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007407 PACKING & LABEL SPECIFICATIONS AA2214SES/J3-AMT SPEC NO: DSAL4011 REV NO: V.1 DATE: NOV/22/2010 PAGE: 6 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007407 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below Lot Tolerance Percent Defective (LTPD) : 10% No. Test Item Standards Test Times / Number of Cycles Damaged Test Condition 1 Continuous operating test - Ta =25C ,IF = maximum rated current* 1,000 h 0 / 22 2 High Temp. operating test EIAJED4701/100(101) Ta = 100C IF = maximum rated current* 1,000 h 0 / 22 3 Low Temp. operating test - Ta = -40C, IF = maximum rated current* 1,000 h 0 / 22 4 High temp. storage test EIAJEDTa = maximum rated storage temperature 4701/100(201) 1,000 h 0 / 22 5 Low temp. storage test EIAJED4701/100(202) Ta = -40C 1,000 h 0 / 22 6 High temp. & humidity storage test EIAJED4701/100(103) Ta = 60C, RH = 90% 1,000 h 0 / 22 7 High temp. & humidity operating test EIAJED4701/100(102) Ta = 60C, RH = 90% IF = maximum rated current* 1,000 h 0 / 22 8 Soldering reliability test EIAJED4701/100(301) Moisture soak : 30C,70% RH, 72h Preheat : 150~180C(120s max.) Soldering temp : 260C(10s) 3 times 0 / 18 9 Thermal shock operating test - Ta = -40C(15min) ~ 100C(15min) IF = derated current at 100C 1,000 cycles 0 / 22 10 Thermal shock test - Ta = -40C(15min) ~ maximum rated storage temperature(15min) 1,000 cycles 0 / 22 11 Electric Static Discharge (ESD) EIAJED4701/100(304) C = 100pF , R2 = 1.5K V = 3000V Once each Polarity 0 / 22 12 Vibration test - a = 196m/s , f = 100~2KHz , t = 48min for all xyz axes 4 times 0 / 22 * : Refer to forward current vs. derating curve diagram Failure Criteria Items Symbols Conditions Failure Criteria luminous Intensity lv IF = 20mA Testing Min. Value <Spec.Min.Value x 0.5 Forward Voltage VF IF = 20mA Testing Max. Value Spec.Max.Value x 1.2 Reverse Current IR VR = Maximum Rated Reverse Voltage Testing Max. Value Spec.Max.Value x 2.5 High temp. storage test - - Occurrence of notable decoloration, deformation and cracking SPEC NO: DSAL4011 REV NO: V.1 DATE: NOV/22/2010 PAGE: 7 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP: 1201007407