M81969/39-01 - CINCH CONNECTORS - Datasheet.Directory

Document Number: 42029 For technical questions, contact: spresale@vishay.com www.vishay.com

Revision: 07-Feb-07 25

Type 730P

Vishay Sprague

Film Capacitors

High Frequency, Wrap-and-Fill, Metallized Polypropylene

Not for New Design

FEATURES

•Excellent AC performance

•Low Power dissipation

•Low dielectric absorption

•Close tolerance

•High stability

PERFORMANCE CHARACTERISTICS

Operating Temperature: - 55 °C to + 85 °C

Voltage derating:

At + 105 °C, 50 % of + 85 °C rating

ESR: 20 kHz to 100 kHz

Capacitance Range: 0.022 µF to 10.0 µF

Capactiance Tolerance: ± 20 %, ± 10 %, ± 5 %

DC Voltage Rating: 100 WVDC to 630 WVDC

AC Voltage Rating: 70 Vrms to 275 Vrms, 60 Hz to 400 Hz

Dissipation Factor: 0.1 % maximum

Measure all units at 1000 Hz at + 25 °C

DC Voltage Test: 200 % of rated voltage for 2 minutes

AC Voltage Test: 130 % of rated rms voltage at 60 Hz for

15 seconds

Insulation Resistance: Measured at 100 WVDC after a

2 minute charge.

At + 25 °C: 200 000 Megohm - Microfarads

or 400 000 Megohm minimum.

At + 85 °C: 10 000 Megohm - Microfarads

or 20 000 Megohm minimum.

At + 105 °C: 1000 Megohm - Microfarads

or 2000 Megohm minimum.

Vibration Test (Condition B): No mechanical damage,

short, open or intermittent circuits.

DC Life Test: 150 % of rated voltage for 1000 hours

at + 85 °C. No open or short circuits. No visible damage.

Maximum Δ CAP ± 1.0 %

Minimum IR = 50 % of initial limit

Maximum DF = 0.12 %

Humidity Test: 95 % relative humidity at + 40 °C for 250

hours. No visible damage.

Maximum Δ CAP ± 1.0 %

Minimum IR = 20 % of initial limit

Maximum DF = 0.12 %

AC Life Test: 110 % of rated rms voltage at 60 Hz for 1000

hours at + 85 °C.

Maximum Δ CAP ± 5 %

Minimum IR = 50 % of initial limit

Maximum DF = 0.12 %

PHYSICAL CHARACTERISTICS

Lead Pull: 5 pounds (2.3 kilograms) for one minute. No

physical damage.

Lead Bend: After three complete consecutive bends. No

damage.

Marking: Sprague® trademark, type or part number,

capacitance and voltage.

* Leads to be within 0.062" [1.57 mm] of center line at egrees but not less than 0.031" [0.79 mm] from edge.

DIMENSIONS in inches [millimeters]

± 0.062 [1.57]

1.750

[44.45]

Min.

Solid Tinned Wire

0.032 [0.81] Nominal Dia.

(No. 20 AWG)

1.750

[44.45]

Min.

Max.

www.vishay.com For technical questions, contact: spresale@vishay.com Document Number: 42029

26 Revision: 07-Feb-07

Type 730P

Vishay Sprague Film Capacitors

High Frequency, Wrap-and-Fill,

Metallized Polypropylene

Not for New Design

* These ratings are stocked.

** Part Numbers listed are for a capacitance tolerance of ± 10 %. To specifiy ± 20 % tolerance, change the “X9” in the Part Number to “X0”;

for ± 5 %, from “X9” to “X5”.

*** The peak current pulse capability ot these capacitors is 10 amperes/µF. The maximum rate voltage change is 10 V/µS.

STANDARD RATINGS in inches [millimeters]

CAPACITANCE

(µF) PART NUMBER**

ESR

(Milliohms)

20 kHz -

100 Khz

MAXIMUM RIPPLE CURRENT

(Amps rms) at 20 kHz

Case Temperature*** at

CASE SIZE

D L + 25 °C + 35 °C + 45 °C + 55 °C + 65 °C + 75 °C + 85 °C

100 WVDC

0.22 730P224X9100 0.275 [7.0] 0.75 [19.0] - Not applicable. These capacitance values are not customarily

used in switched-mode power supplies.

0.27 730P274X9100 0.298 [7.6] 0.75 [19.0] -

0.33 730P334X9100 0.324 [8.2] 0.75 [19.0] -

0.39 730P394X9100 0.347 [8.8] 0.75 [19.0] - - - - - - - -

0.47* 730P474X9100 0.376 [9.6] 0.75 [19.0] 37.0 3.7 3.4 3.1 2.8 2.5 2.0 1.4

0.56 730P564X9100 0.321 [8.2] 1.00 [25.4] 35.0 3.9 3.6 3.3 2.9 2.6 2.1 1.5

0.68 730P684X9100 0.348 [8.8] 1.00 [25.4] 33.0 4.1 3.8 3.5 3.1 2.8 2.2 1.6

0.82 730P824X9100 0.377 [9.6] 1.00 [25.4] 31.0 4.3 4.0 3.6 3.2 2.9 2.3 1.7

1.0* 730P105X9100 0.421 [10.7] 1.00 [25.4] 26.0 5.5 5.1 4.7 4.2 3.6 2.8 2.6

1.2 730P125X9100 0.454 [11.5] 1.00 [25.4] 24.0 5.7 5.3 4.9 4.4 3.8 3.0 2.8

1.5 730P155X9100 0.500 [12.7] 1.00 [25.4] 20.0 6.1 5.5 5.1 4.6 4.0 3.2 3.1

1.8 730P185X9100 0.541 [13.7] 1.00 [25.4] 19.0 6.3 5.7 5.3 4.8 4.1 3.4 3.0

2.0 730P205X9100 0.486 [12.3] 1.25 [31.8] 18.0 6.5 6.0 5.5 4.9 4.2 3.5 3.2

2.2 730P225X9100 0.507 [12.9] 1.25 [31.8] 18.0 6.8 6.3 5.7 5.1 4.4 3.6 3.3

2.7 730P275X9100 0.554 [14.1] 1.25 [31.8] 17.0 7.1 6.5 6.0 5.3 4.6 3.7 3.4

3.0 730P305X9100 0.581 [14.8] 1.25 [31.8] 16.0 7.3 6.7 6.2 5.5 4.8 3.9 3.5

3.3 730P335X9100 0.606 [15.4] 1.25 [31.8] 16.0 7.4 6.8 6.4 5.6 4.9 4.0 3.6

3.9 730P395X9100 0.654 [16.6] 1.25 [31.8] 15.0 7.6 6.9 6.6 5.8 5.1 4.1 3.7

4.0 730P405X9100 0.537 [13.6] 1.75 [44.5] 15.0 7.8 7.0 6.7 5.9 5.2 4.2 3.8

4.7 730P475X9100 0.577 [14.7] 1.75 [44.5] 15.0 8.1 7.4 6.8 6.0 5.3 4.3 3.9

5.0 730P505X9100 0.593 [15.1] 1.75 [44.5] 14.0 8.3 7.6 7.0 6.2 5.4 4.4 4.0

5.6 730P565X9100 0.624 [15.8] 1.75 [44.5] 14.0 8.4 7.7 7.1 6.4 5.5 4.5 4.1

6.0 730P605X9100 0.644 [16.4] 1.75 [44.5] 14.0 8.5 7.8 7.2 6.5 5.6 4.6 4.2

6.8 730P685X9100 0.682 [17.3] 1.75 [44.5] 13.0 8.5 8.0 7.4 6.7 5.7 4.7 4.3

8.0 730P805X9100 0.735 [18.7] 1.75 [44.5] 13.0 8.6 8.3 7.7 6.8 6.0 4.8 4.4

8.2 730P825X9100 0.743 [18.9] 1.75 [44.5] 13.0 8.8 8.6 8.0 7.0 6.1 4.9 4.5

10.0 730P106X9100 0.815 [20.7] 1.75 [44.5] 12.0 9.0 9.0 8.5 7.6 6.6 5.4 4.9

250 WVDC

0.1* 730P104X9250 0.279 [7.1] 0.75 [19.0] -

Not applicable. These capacitance values are not customarily

used in switched-mode power supplies.

0.12 730P124X9250 0.300 [7.6] 0.75 [19.0] -

0.15 730P154X9250 0.327 [8.3] 0.75 [19.0] -

0.18 730P184X9250 0.353 [9.0] 0.75 [19.0] -

0.22* 730P224X9250 0.306 [7.8] 1.00 [25.4] -

0.27 730P274X9250 0.333 [8.5] 1.00 [25.4] -

0.33* 730P334X9250 0.362 [9.2] 1.00 [25.4] -

0.39 730P394X9250 0.389 [9.9] 1.00 [25.4] - - - - - - - -

0.47* 730P474X9250 0.422 [10.7] 1.00 [25.4] 35.0 3.8 3.7 3.6 3.4 2.9 2.4 1.7

0.56 730P564X9250 0.464 [11.8] 1.00 [25.4] 33.0 3.9 3.8 3.7 3.5 3.1 2.5 1.8

0.68 730P684X9250 0.425 [10.8] 1.25 [31.8] 32.0 4.0 3.9 3.8 3.7 3.2 2.6 1.9

0.82 730P824X9250 0.471 [12.0] 1.25 [31.8] 31.0 4.2 4.1 4.0 3.9 3.4 2.8 2.0

1.0* 730P105X9250 0.513 [13.0] 1.25 [31.8] 28.0 4.4 4.4 4.4 4.4 4.3 3.5 3.2

1.2 730P125X9250 0.554 [14.1] 1.25 [31.8] 27.0 4.7 4.6 4.5 5.0 4.5 3.7 3.3

1.5 730P155X9250 0.613 [15.6] 1.25 [31.8] 26.0 5.1 5.0 4.9 5.4 4.7 3.9 3.5

1.8 730P185X9250 0.667 [17.0] 1.25 [31.8] 25.0 5.9 5.8 5.7 5.7 5.0 4.1 3.7

2.0* 730P205X9250 0.700 [17.8] 1.25 [31.8] 21.0 7.2 7.2 6.8 6.0 5.2 4.3 3.9

2.2 730P225X9250 0.610 [15.5] 1.75 [44.5] 20.0 8.4 7.5 7.0 6.3 5.4 4.5 4.1

2.7 730P275X9250 0.669 [17.0] 1.75 [44.5] 19.0 8.6 7.8 7.3 6.6 5.7 4.7 4.3

3.0 730P305X9250 0.703 [17.9] 1.75 [44.5] 18.0 9.0 8.3 7.6 6.8 5.9 4.8 4.4

3.3 730P335X9250 0.734 [18.6] 1.75 [44.5] 18.0 9.0 8.4 7.8 7.0 6.0 4.9 4.5

3.9 730P395X9250 0.794 [20.2] 1.75 [44.5] 17.0 9.0 8.5 8.0 7.2 6.2 5.0 4.6

4.0 730P405X9250 0.803 [20.4] 1.75 [44.5] 16.0 9.0 8.6 8.2 7.4 6.3 5.1 4.7

4.7 730P475X9250 0.866 [22.0] 1.75 [44.5] 16.0 9.0 8.8 8.5 7.7 6.6 5.3 4.9

5.0 730P505X9250 0.892 [22.7] 1.75 [44.5] 15.0 9.0 9.0 8.8 7.9 6.8 5.6 5.1

5.6 730P565X9250 0.941 [23.9] 1.75 [44.5] 15.0 9.0 9.0 8.9 8.0 7.0 5.8 5.3

6.0 730P605X9250 0.972 [24.7] 1.75 [44.5] 15.0 9.0 9.0 9.0 8.2 7.2 5.9 5.5

6.8 730P685X9250 0.882 [22.4] 2.25 [57.2] 15.0 9.0 9.0 9.0 8.4 7.4 6.0 5.6

8.0 730P805X9250 0.953 [24.2] 2.25 [57.2] 14.0 9.0 9.0 9.0 8.7 7.8 6.3 5.8

8.2 730P825X9250 0.964 [24.5] 2.25 [57.2] 14.0 9.0 9.0 9.0 8.8 7.9 6.4 5.9

10.0 730P106X9250 1.060 [26.9] 2.25 [57.2] 13.0 9.0 9.0 9.0 8.9 8.3 6.8 6.2

Type 730P

Film Capacitors

High Frequency, Wrap-and-Fill,

Metallized Polypropylene

Vishay Sprague

Document Number: 42029 For technical questions, contact: spresale@vishay.com www.vishay.com

Revision: 07-Feb-07 27

Not for New Design

* These ratings are stocked.

** Part Numbers listed are for a capacitance tolerance of ± 10 %. To specifiy ± 20 % tolerance, change the “X9” in the Part Number to “X0”;

for ± 5 %, from “X9” to “X5”.

*** The peak current pulse capability ot these capacitors is 10 amperes/µF. The maximum rate voltage change is 10 V/µS.

STANDARD RATINGS in inches [millimeters]

CAPACITANCE

(µF)

PART

NUMBER**

ESR

(Milliohms)

20 kHz -

100 Khz

MAXIMUM RIPPLE CURRENT

(Amps rms) at 20 kHz

Case Temperature*** at

CASE SIZE

D L + 25 °C + 35 °C + 45 °C + 55 °C + 65 °C + 75 °C + 85 °C

400 WVDC

0.047 730P473X9400 0.258 [6.6] 0.75 [19.0] -

Not applicable. These capacitance values are not customarily

used in switched-mode power supplies.

0.056 730P563X9400 0.275 [7.0] 0.75 [19.0] -

0.068 730P683X9400 0.297 [7.5] 0.75 [19.0] -

0.082 730P823X9400 0.320 [8.1] 0.75 [19.0] -

0.1* 730P104X9400 0.348 [8.8] 0.75 [19.0] -

0.12 730P124X9400 0.299 [7.6] 1.00 [25.4] -

0.15* 730P154X9400 0.328 [8.3] 1.00 [25.4] -

0.18 730P184X9400 0.353 [9.0] 1.00 [25.4] -

0.22 730P224X9400 0.385 [9.8] 1.00 [25.4] -

0.27 730P274X9400 0.421 [10.7] 1.00 [25.4] -

0.33 730P334X9400 0.469 [11.9] 1.00 [25.4] -

0.39 730P394X9400 0.503 [12.8] 1.00 [25.4] - - - - - - - -

0.47* 730P474X9400 0.545 [13.8] 1.00 [25.4] 32.0 5.7 5.5 5.0 4.4 3.8 3.2 2.2

0.56 730P564X9400 0.506 [12.9] 1.25 [31.8] 31.0 5.7 5.7 5.3 4.4 4.1 3.3 2.3

0.68 730P684X9400 0.551 [14.0] 1.25 [31.8] 30.0 5.7 5.7 5.5 4.8 4.3 3.5 2.4

0.82 730P824X9400 0.599 [15.2] 1.25 [31.8] 28.0 5.7 5.7 5.6 5.3 4.5 3.7 2.6

1.0* 730P105X9400 0.655 [16.6] 1.25 [31.8] 27.0 5.7 5.7 5.7 5.7 5.7 4.7 4.3

1.2 730P125X9400 0.712 [18.1] 1.25 [31.8] 26.0 6.3 6.2 6.0 5.9 5.8 4.9 4.5

1.5 730P155X9400 0.658 [16.7] 1.75 [44.5] 25.0 7.0 6.9 6.7 6.6 6.5 5.2 4.7

1.8 730P185X9400 0.716 [18.2] 1.75 [44.5] 23.0 8.0 7.9 7.8 7.7 6.8 5.5 5.0

2.0* 730P205X9400 0.752 [19.1] 1.75 [44.5] 21.0 9.0 9.0 9.0 8.0 7.0 5.7 5.2

2.2 730P225X9400 0.786 [20.0] 1.75 [44.5] 20.0 9.0 9.0 9.0 8.3 7.4 5.9 5.4

2.7 730P275X9400 0.865 [22.0] 1.75 [44.5] 19.0 9.0 9.0 9.0 8.6 7.6 6.0 5.6

3.0* 730P305X9400 0.909 [23.1] 1.75 [44.5] 17.0 9.0 9.0 9.0 9.0 7.9 6.4 5.9

3.3 730P335X9400 0.951 [24.2] 1.75 [44.5] 16.0 9.0 9.0 9.0 9.0 8.1 6.6 6.3

3.9 730P395X9400 1.031 [26.2] 1.75 [44.5] 15.0 9.0 9.0 9.0 9.0 8.3 6.8 6.5

630 WVDC

0.022* 730P223X9630 0.283 [7.2] 0.75 [19.0] -

Not applicable. These capacitance values are not customarily

used in switched-mode power supplies.

0.027 730P273X9630 0.307 [7.8] 0.75 [19.0] -

0.033 730P333X9630 0.334 [8.5] 0.75 [19.0] -

0.039 730P393X9630 0.358 [9.1] 0.75 [19.0] -

0.047 730P473X9630 0.388 [9.9] 0.75 [19.0] -

0.056 730P563X9630 0.418 [10.6] 0.75 [19.0] -

0.068 730P683X9630 0.346 [8.8] 1.00 [25.4] -

0.082 730P823X9630 0.374 [9.5] 1.00 [25.4] -

0.1 730P104X9630 0.408 [10.4] 1.00 [25.4] -

0.12 730P124X9630 0.443 [11.3] 1.00 [25.4] -

0.15 730P154X9630 0.496 [12.6] 1.00 [25.4] -

0.18 730P184X9630 0.538 [13.7] 1.00 [25.4] -

0.22 730P224X9630 0.496 [12.6] 1.25 [31.8] -

0.27 730P274X9630 0.542 [13.8] 1.25 [31.8] -

0.33 730P334X9630 0.593 [15.1] 1.25 [31.8] -

0.39 730P394X9630 0.639 [16.2] 1.25 [31.8] - - - - - - - -

0.47 730P474X9630 0.696 [17.7] 1.25 [31.8] 28.0 6.8 6.3 5.8 5.2 4.5 3.6 2.6

0.56 730P564X9630 0.608 [15.4] 1.75 [44.5] 26.0 7.4 6.9 6.3 5.6 4.8 4.0 2.8

0.68 730P684X9630 0.664 [16.9] 1.75 [44.5] 25.0 7.8 7.2 6.6 5.9 5.1 4.2 2.9

0.82 730P824X9630 0.724 [18.4] 1.75 [44.5] 22.0 8.1 7.5 6.9 6.2 5.3 4.3 3.1

1.0* 730P105X9630 0.794 [20.2] 1.75 [44.5] 18.0 8.6 7.9 7.3 6.5 5.6 4.6 3.6

ORDERING INFORMATION

730P 224 X9 100

TYPE CAPACITANCE CAPACITANCE TOLERANCE DC VOLTAGE RATING*

This is expressed in picofarads. The first two

digits are the significant figures. The third is

the number of zeros to follow.

X0 = ± 20 %

X9 = ± 10 %

X5 = ± 5 %

This is expressed in volts.

* At + 85 °C, AC rms ratings for frequencies up to and including 400 Hz correspond to this table:

WVDC 100 250 400 630

RATED rms VOLTS 70 175 275 275

Document Number: 91000 www.vishay.com

Revision: 18-Jul-08 1

Disclaimer

Legal Disclaimer Notice

Vishay

All product specifications and data are subject to change without notice.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf

(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein

or in any other disclosure relating to any product.

Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any

information provided herein to the maximum extent permitted by law. The product specifications do not expand or

otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed

therein, which apply to these products.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this

document or by any conduct of Vishay.

The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless

otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such

applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting

from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding

products designed for such applications.

Product names and markings noted herein may be trademarks of their respective owners.