Atmel ATA6628/ATA6630 Development Board V1.1 1. Introduction (R) The development board for the Atmel ATA6628/ATA6630 is designed to give users a quick start using these ICs and prototyping and testing new LIN designs. The Atmel ATA6628 and Atmel ATA6630 are system basis chips (SBCs) with a fully integrated LIN transceiver in compliance with the LIN specification 2.0, 2.1 and SAEJ2602-2. The SBCs each have a window watchdog with adjustable trigger time and a 3.3V/85mA respectively 5V/85mA low drop voltage regulator. The output current of the regulator can be boosted by using an external NPN transistor. In addition, the Atmel ATA6628/ATA6630 has an integrated voltage divider that makes it possible to measure the battery voltage precisely. Atmel ATA6628/ Atmel ATA6630 Development Board V1.1 Application Note The ATA6628 and the ATA6630 are nearly identical, the only difference between these circuits is the regulator's output voltage. The combination of the features included in the Atmel ATA6628/ATA6630 makes it possible to develop simple though powerful and cheap slave and master nodes for LIN bus systems. The ICs are designed to handle low-speed data communication in vehicles such as that found in convenience electronics. Improved slope control at the LIN driver ensures secure data communication of up to 20kBaud. Sleep mode and silent mode guarantee very low current consumption even in the case of a floating bus or a short circuit between the bus line and GND. This document has been created as a quick start guide on using the Atmel ATA6628/ATA6630 development board. For more detailed information about the use of these devices, please refer to the corresponding datasheet. 9202B-AUTO-03/11 Figure 1-1. 1.1 ATA6628/ATA6630 Development Board V1.1 Development Board Features The development board for the Atmel(R) ATA6628/ATA6630 has the following features: * * * * * All Components for Putting the Atmel ATA6628/ATA6630 in Operation Included Placeholders for some Optional Components for Extended Functions Included Easy Accessibility of All Pins Easily Adaptable Watchdog Times by Replacing a Resistor Possibility to Boost Up the Output Current of the Voltage Regulator Using the Onboard NPN Transistor T1 by Removing the Jumper J1 * Option between Master or Slave Operation (Mounting D3 and R4) 1.2 Quick Start The development board for the Atmel ATA6628/ATA6630 is shipped with all necessary components and a default jumper setting to immediately start the development of a LIN slave node. Connecting an external 12V DC power supply between the terminals VB and GND, puts the circuit in fail-safe mode and a voltage of 5V (3.3V) DC supplied by the internal voltage regulator can be measured between VCC and GND. 2 Atmel ATA6628/ATA6630 9202B-AUTO-03/11 Atmel ATA6628/ATA6630 In addition, the following voltage states can be measured at the pins WD_OSC, INH, RXD and LIN as given in Table 1-1 and Table 1-2. Table 1-1. Atmel(R) ATA6630 PVCC WD_OSC INH RXD LIN Transceiver Fail-safe mode 5V 1.23V On Low recessive Off Normal mode 5V 1.23V On LIN depending TXD depending On PVCC WD_OSC INH RXD LIN Transceiver 3.3V 1.23V On Low recessive Off On LIN depending TXD depending On Table 1-2. Atmel ATA6628 Fail-safe mode Normal mode 3.3V 1.23V Because the window watchdog of the Atmel ATA6628/ATA6630 is already active in fail-safe mode, a periodic reset signal is generated at the NRES pin as long as no trigger signal can be received at the watchdog trigger input NTRIG. Normally the connected microcontroller is monitored with the watchdog, so it has to generate the required trigger signal described in Section 2.3 "The Window Watchdog (NTRIG and NRES)" on page 7 and in more detail in the datasheet of the Atmel ATA6628/ATA6630. For the quick start it is sufficient to generate a square-wave signal with VPP = VCC and f = 50Hz at the NTRIG pin (this is only recommended for testing purposes). In order to check that the watchdog is triggered in the expected way, the NRES reset pin can be monitored until a continuous high level is available. Please note that the communication is still inactive during fail-safe mode. In order to communicate via the LIN bus interface you have to switch to normal mode by applying the VCC voltage (5V or 3.3V respectively) to the EN pin. 3 9202B-AUTO-03/11 2. Hardware Description The following sections contain a brief description of normal operating conditions. Please refer to the respective datasheet for more information about any of the features mentioned. 2.1 Power Supply (VB and GND) In order to get the development board running, an external 5.7V - 27V DC power supply is required between the terminals VB and GND. The input circuit is protected against inverse polarity with the D1 protection diode, resulting in a difference between the VB and VS level of approximately 0.7V. 2.2 Voltage Regulator (PVCC and VCC) The internal 5V or 3.3V low drop voltage regulator is capable of driving loads up to 50mA over a wide range of supply voltage and ambient temperature with an accuracy of 2%, so the SBC is able to supply a microcontroller, sensors and/or other ICs. In regular operation the PVCC and VCC pins have to be connected directly on the development board. This is done by setting the J1 jumper; the PVCC pin is led off the board. In the application these two adjacent pins are directly connected by soldering. All characteristics and descriptions in this chapter are valid for a direct connection between PVCC and VCC and have been measured with the Atmel (R) ATA6630. The curves for the ATA6628 are generally the same but the absolute value is 3.3V instead of 5V. The PVCC voltage versus the ambient temperature at different load currents is shown in Figure 2.1. Figure 2-1. PVCC versus Temperature at Different Load Currents (ATA6630) 5.0 10 VCC (V) 5.0 0 5 5.0 0 0 4 .9 9 5 0mA 20mA 40mA 60mA 80mA 4 .9 9 0 4 .9 8 5 -50 0 50 10 0 150 Ambient Temperature (C) The voltage regulator is able to drive load currents higher than 50mA, but the limiting factor is the resulting power dissipation. The current limitation is specified with at least 85mA, meaning the circuit can deliver at least this current but due to the power dissipation not at a high supply voltage and/or high ambient temperature. It is possible to achieve an excellent thermal behavior with the heat slug soldered to the PCB. The resulting SOA curve is depicted in Figure 2-2 on page 5. 4 Atmel ATA6628/ATA6630 9202B-AUTO-03/11 Atmel ATA6628/ATA6630 Figure 2-2. SOA: I_PVCC versus VS at Different Ambient Temperatures 90 Tamb = 105C 80 70 Tamb = 115C IVCC/mA 60 50 Tamb = 125C 40 30 20 10 0 5 6 7 8 9 10 11 12 13 14 15 16 17 18 VS/V The voltage regulator is protected against overloads by means of current limitation and overtemperature shutdown. In addition, the output voltage is monitored and causes a reset signal at the NRES pin if it drops below the undervoltage threshold. The voltage regulator requires an external capacitor for compensation and for smoothing disturbances from the microcontroller and the other devices supplied by the PVCC voltage. Atmel(R) recommends using an electrolytic capacitor with C 1.8F and a ceramic capacitor with C = 100nF. The values of these capacitors can be varied by the customer, depending on the application. But the ESR value of the electrolytic capacitor should be 0.2 < ESR < 5 in order to guarantee stable behavior under all conditions (load, supply voltage, temperature). A Tantalum capacitor with 10F and a ceramic capacitor with 100nF are mounted on the development board at the regulator's output. The following diagram shows what the load-transient response looks like with this external circuitry. Figure 2-3. Load-transient Response, Ch1: IOUT, Ch2: PVCC 5 9202B-AUTO-03/11 At a short circuit between PVCC and GND, the output of the regulator limits the output current. Because of undervoltage, NRES switches to low and sends a reset to the microcontroller. The IC switches into fail-safe mode. Due to the power dissipation the chip temperature increases and, if it exceeds the PVCC overtemperature threshold, the output switches off. The chip cools down and after the temperature hysteresis the output switches on again. Because of fail-safe mode, the PVCC voltage switches on again even if EN is low. The resulting characteristic of the output current at a short circuit depends on the supply voltage, the ambient temperature, and the thermal connection of the IC to the PCB. The short-circuit current of the voltage regulator at room temperature and a battery voltage of 18V is depicted in Figure 2-4. Figure 2-4. Voltage Regulator: Current Limitation at a Short-circuit between PVCC and GND To boost the maximum load current, an external NPN transistor may be used with its base connected to the VCC pin and its emitter connected to the PVCC pin. In this case the regulated output voltage of 5V or 3.3V is available at the PVCC pin. For this reason the PVCC pin and not the VCC pin is led off the board and is always mentioned when a connection has to be made to the 5V or 3.3V regulator. The procedure of boosting the voltage regulator is described in Section 3. "Boosting Up the Voltage Regulator" on page 12. Note: 6 If an external NPN transistor is used for boosting the output current, there is no short-circuit protection at PVCC. Atmel ATA6628/ATA6630 9202B-AUTO-03/11 Atmel ATA6628/ATA6630 2.3 The Window Watchdog (NTRIG and NRES) The watchdog anticipates a trigger signal from the microcontroller at the NTRIG input (negative edge) within a defined time window. If no correct trigger signal is received, a reset signal is generated at the NRES output. During Silent or Sleep Mode the watchdog is switched off to reduce current consumption. The NTRIG input includes a pull-down resistor. A minimum time for the first watchdog pulse is required after the undervoltage reset at the NRES pin disappears and is defined as lead time td. The timing basis of the watchdog is provided by the internal oscillator, whose time period tOSC is adjustable via the external resistor R3 at the pin WD_OSC. The voltage at this pin is 1.23V. There is the resistor R3 with a value of 51k mounted on the development board resulting in the timing sequence in Figure 2-5. Figure 2-5. Timing Sequence with R3 = 51k VCC 3.3V/5V Undervoltage Reset NRES Watchdog Reset tnres = 4ms treset = 4ms td = 155ms t1 t1 = 20.6ms t2 t2 = 21ms twd NTRIG ttrig > 200ns If you want to change the watchdog times mentioned above, it is only necessary to change the value of the external resistor R3 (refer to the datasheet). If the watchdog is not used in the application it can be disabled by connecting the mode pin with PVCC. This switches off the voltage at the pin WD_OSC and you can either tie this pin to GND or leave it open. 7 9202B-AUTO-03/11 2.4 2.4.1 LIN Interface (LIN, TXD and RXD) Bus Pin (LIN) A low side driver with internal current limitation, thermal shutdown, and an internal pull-up resistor in compliance with LIN spec 2.x is implemented. LIN receiver thresholds comply with the LIN protocol specification. The fall time from recessive to dominant bus state and the rise time from dominant to recessive bus state are slope-controlled. The allowed voltage range is between -27V and +40V. The reverse current from the LIN bus to VS is < 2A even in case of battery disconnection. During a short circuit at the pin LIN to Vbattery, the output limits the output current. Due to the power dissipation the chip temperature exceeds the overtemperature threshold and the LIN output is switched off. The chip cools down and after the temperature hysteresis the output switches on again. RXD stays on high because LIN is high. During LIN overtemperature switch-off, the VCC voltage regulator works independently. On the board the LIN pin is equipped with a 220pF capacitor to GND. In addition, the two extra components diode D2 (LL4148) in series with resistor R3 (1 k) needed for using the development board for a LIN master application have designated placeholders for convenient mounting. 2.4.2 Input/ Output Pin (TXD) In normal mode the TXD pin is the microcontroller interface for controlling the LIN output state. TXD must be pulled to ground in order to have the LIN bus low. If TXD is high or not connected (internal pull-up resistor), the LIN output transistor is turned off with the bus in recessive state pulled up by the internal resistor. If TXD is low, the LIN output transistor is turned on and the bus is in dominant state. An internal timer prevents the bus line from being driven permanently in dominant state. If the TXD input is forced to low for longer than tdom > 27ms, the LIN bus driver is switched to recessive state. To reactivate the LIN Bus driver, switch TXD to high for longer than 10s. The actual level at the TXD pin is relevant even when switching to sleep mode. During fail-safe mode, this pin is used as an output and signals the fail-safe source. It is current limited to I < 8mA. 2.4.3 Output Pin (RXD) This pin reports the state of the LIN bus to the microcontroller. LIN high (recessive state) is reported by a high level at RXD, LIN low (dominant state) is reported by a low level at RXD. The output has an internal pull up resistor with typ. 5k to PVCC. The output is short-circuit protected. RXD is switched off in unpowered mode. During fail-safe mode it signals the fail-safe source together with the TXD pin. 8 Atmel ATA6628/ATA6630 9202B-AUTO-03/11 Atmel ATA6628/ATA6630 2.5 Voltage Monitoring (VBATT, PV, DIV_ON) With the integrated switchable voltage divider it is possible to very accurately measure the battery voltage. The upper terminal of the divider is connected via a switch to the VBATT pin, the tap is connected to the PV pin, and the lower terminal is internally connected to GND. The control of the switch is done by the independent low voltage input DIV_ON. A high level (PVCC) switches the voltage divider on and a low level switches it off. There is an integrated pull-down resistor at the DIV_ON input. With this switch it is possible to reduce the current consumption, because the voltage divider can be only active during measurement of battery voltage. The VBATT pin can be connected directly with the battery voltage via a low-ohmic resistor. The divider ratio is for both versions 1:6, the total resistance is about 100k. The input current at VBATT consists of the current through the voltage divider and a constant current of about 20A, which is needed for the control of the internal switch at VBATT. 2.6 Enable Input (EN) This pin controls the operating mode of the device. If EN = 1 the circuit is in normal mode, with transmission paths from TXD to LIN and from LIN to RXD both active and the voltage regulator also switched on. IF EN is switched to low while TXD is still high, the device is forced to silent mode. No data transmission is then possible, the LIN pin is pulled to VS by a weak current source, the current consumption is reduced to IVS typ. 40A, but the voltage regulator has its full functionality. If EN is switched to low while TXD is low, the device is forced into sleep mode, the LIN pin is pulled to VS by a weak current source, and the voltage regulator is switched off. During sleep mode the device is still supplied from the battery voltage, the supply current is typically 10A. The pin EN provides a pull-down resistor in order to force the transceiver into sleep or silent mode if the pin is not connected. In order to avoid any influence to the LIN pin while switching into sleep mode, it is possible to switch the EN to low up to 3.2s earlier than the TXD. Therefore, the best and easiest way to switch the Atmel(R) ATA6628/ATA6630 into sleep mode is with two simultaneous falling edges at TXD and EN. 2.7 SP_ Mode Input Pin The SP_Mode pin is a low-voltage input. A high level during normal mode activates the high speed mode of the LIN transceiver. In this mode the slope control is switched off so the rising edge as well as the falling edge of the LIN signal are shorter. In high speed mode the achieved baud rate is higher than 100Kbaud. With this feature for example the flash memory of the connected microcontroller can be programmed via the LIN bus in an acceptable time. During high speed mode the EMC characteristics of the circuit are different from the values in normal LIN communication. Reverting to LIN 2.x transceiver mode with slope control is possible if you switch the SP_MODE pin to low. 9 9202B-AUTO-03/11 2.8 Mode and TM inputs (MODE and TM) The TM input is only used for Atmel(R) internal testing purposes and therefore always connected directly to GND. The mode input is pulled down by the 4.7k resistor R1 on the board thus the watchdog is active in fail-safe and normal mode. Especially during the early development phase it can be helpful to have the option of deactivating the watchdog in order to debug the application program without disturbing RESETS caused by the watchdog. The watchdog can therefore be switched off by connecting the MODE pin to PVCC externally. If the watchdog is not used in an application, the mode pin can be connected directly to PVCC. 2.9 Wake Input (WAKE) The WAKE input is a high-voltage input used to wake up the device from sleep mode or silent mode. It is usually connected to an external transistor or a switch to generate a local wake-up. A pull-up current source with typically 10A is implemented as well as a debounce timer with a typical debounce time of 70s. On the development board there is the push button S1 to generate a local wake-up by pulling the WAKE pin to GND. The resistor R5 = 2.7k is needed to limit the input current in case of voltage transients and in case of GND shifts. Even if the WAKE pin is pulled to GND, it is possible to switch the IC into sleep or silent mode. Connect the WAKE pin directly to VS if you do not need it. 2.10 Reset Output (NRES) The Reset pin is an open drain output that switches to low during PVCC undervoltage or a watchdog failure. After ramping up the battery voltage or after a wake-up from sleep mode the voltage regulator is switched on and the PVCC voltage exceeds the undervoltage threshold. The implemented undervoltage delay keeps the NRES output at the low level for typ. 4ms after PVCC reaches its nominal value. Then the NRES switches to high and the watchdog waits for the trigger sequence from the microcontroller. The NRES pin also switches to low if the watchdog is not triggered correctly (see Section 2.3 "The Window Watchdog (NTRIG and NRES)" on page 7). An external resistor connected to PVCC is necessary for pulling up the NRES output. This resistor R9 has a value of 10k on the development board. If a reset occurs (NRES is low), the circuit switches to fail-safe mode. 10 Atmel ATA6628/ATA6630 9202B-AUTO-03/11 Atmel ATA6628/ATA6630 2.11 KL_15 Input (KL_15) This pin is a high voltage input used to wake-up the device from sleep or silent mode. It is an edge sensitive pin (low to high transition). It is usually connected to the ignition in order to generate a local wake up in the application, if the ignition is switched on. Although KL_15 pin is at high voltage (Vbat), it is possible to switch the IC into sleep or silent mode. Connect the KL_15 pin directly to GND if you do not need it. A debounce timer with a typical debounce time of 160s is implemented. To protect this pin against voltage transients a series resistor R12 = 47k and a ceramic capacitor C8 with 100nF are recommended. With this RC combination the wake-up time tW_KL15 and therefore the sensitivity against transients on the ignition KL15 can be increased. The wake-up time can be increased further by higher values for C8. 2.12 Inhibit output (INH) This pin is a high-side switch to VS and it is normally used to switch on an external load during normal mode or fail-safe mode. This load could for example be a voltage regulator that supplies a separate module or a voltage divider for measuring the supply voltage. In sleep mode or silent mode the INH output is switched off. For master node applications it is possible to switch off the external master pull-up resistor (R4) by the INH pin. Figure 2-6. Switching the LIN Master Pull-up Resistor Using the INH Output VBAT VS VS RDson INH Atmel ATA6628/ATA6630 (Part) 1K GND LIN sub bus LIN With this measure the current consumption is reduced to a minimum in case of a short circuit between LIN and GND because the Atmel(R) ATA6628/ATA6630 can be switched into sleep mode, meaning the INH output is off. 11 9202B-AUTO-03/11 3. Boosting Up the Voltage Regulator For some applications there is a need for a higher current than the internal voltage regulator can deliver. As the main power dissipation of the IC is created from the output transistor of the voltage regulator, the output current of the voltage regulator has a significant influence on the safe operating area shown in Figure 2-1 on page 4. If the Atmel(R) ATA6628/ATA6630 needs to be operated above the curves depicted in Figure 2-2 on page 5, it is possible to boost the maximum output current by using an external NPN transistor. It is also possible to use this external transistor for increasing the maximum ambient temperature even at a low PVCC output current. With this external transistor the power dissipation of the IC becomes very low because the voltage regulator only has to drive the base current of the transistor T1. This leads to an increased maximum ambient temperature at which the Atmel ATA6628/ATA6630 can operate. Please note that the output voltage is no longer short circuit protected when boosting the output current with an external NPN transistor. Figure 3-1. Voltage Regulator: Boosting Procedure with an External NPN VBAT Boosting up the voltage regulator with an external NPN transistor D1 C2 22F + C1 VS 100nF Vref = 1.25V PMOS + T1 VCC - RDSon < 130 C4 MJD31C + 2.2F 25K R7 3.3 PVCC PVCC C5 600K 100nF + C3 10F Int. Logic incl. Pull-up Resistors 200K ATA6628/ATA6630 (partly) GND 12 Atmel ATA6628/ATA6630 9202B-AUTO-03/11 Atmel ATA6628/ATA6630 For this case on the development board the NPN transistor T1 (MJD31C) is already mounted in a D-PAK package. The base of the transistor T1 is connected to VCC and the emitter is connected to PVCC. In addition to the transistor itself there are two more components that need to be placed on the development board: the resistor R7 (3.3) and the electrolytic capacitor C4 (2.2F) connected to the base of T1. These two parts are needed for stability reasons. The jumper J1 has to be removed in order to activate the transistor T1. Figure 3-2. Boosting up the Voltage Regulator The limiting parameter for the output current is the maximum power dissipation of the external NPN transistor. In the version at this stage the thermal resistance of the MJD31C soldered on the minimum pad size is 80K/W, this means the possible maximum output current at VS = 12V is approximately 230mA at room temperature. It is not recommended to exceed this limit because the transistor could be damaged as a result of overtemperature. If a higher output current is required, additional cooling of the external transistor has to be ensured (see Figure 3-3, Figure 3-4 and Figure 3-5 on page 14). 13 9202B-AUTO-03/11 The diagrams on this page show the maximum output current Imax of the voltage regulator as a function of the supply voltage VS at different levels of cooling respectively thermal resistances RthJA of the external NPN- transistor T1. Figure 3-3. Imax versus VS at RthJA = 80K/W 3 50 300 Imax (mA) 2 50 200 150 10 0 Ta = 25C 50 Ta = 85C Ta = 125C 0 10 12 14 16 18 20 VS (V) Figure 3-4. Imax versus VS at RthJA = 50K/W 600 50 0 Imax (mA) 400 300 200 Ta = 25C Ta = 85C 10 0 Ta = 125C 0 10 12 14 16 18 20 VS (V) Figure 3-5. Imax versus VS at RthJA = 20K/W 14 0 0 12 0 0 Imax (mA) 10 0 0 800 600 Ta = 25C 400 Ta = 85C 200 Ta = 125C 0 10 12 14 16 18 20 VS (V) 14 Atmel ATA6628/ATA6630 9202B-AUTO-03/11 Atmel ATA6628/ATA6630 In the following diagrams some typical operating characteristics measured with the Atmel(R) ATA6630-EK development board are shown. The supply voltage VS is approximately a diode forward voltage lower than the battery voltage VB (reverse battery protection). Please note that if an external NPN transistor is used for boosting this voltage, the PVCC voltage has no short circuit protection. Figure 3-6. Output Voltage PVCC versus Temperature at Different Load Currents 5.0 0 8 5.0 0 6 PVCC (V) 5.0 0 4 20mA 5.0 0 2 60mA 5.0 0 0 100mA 200mA 4 .9 9 8 4 .9 9 6 4 .9 9 4 4 .9 9 2 -50 0 50 10 0 150 Ambient Temperature (C) Figure 3-7. Load Transient Response Ch1: IOUT, Ch2: PVCC 15 9202B-AUTO-03/11 4. Schematic and Layout of the Development Board for the Atmel ATA6628/ATA6630 Figure 4-1. Schematic of the Development board for the Atmel(R) ATA6628/ATA6630 D1 KL15 VB LL4148 + C2 R2 470 22F/50V VS C1 T1 MJD31C J1 C4 VCC 2.2F 100nF R2 47k + C8 C10 NTRIG R5 VBATT KL15 INH 2.7k KL15 INH C9 S1 WAKE VS EN NTRIG WAKE WAKE 18 17 MODE EN EN MODE NTRIG 16 NTRIG PVCC VBATT EN 19 100nF R1 4.7k GND 1 15 Atmel ATA6628/ ATA6630 2 3 14 13 QFN 5x5mm 0.65mm pitch 20 lead 4 12 5 11 6 LIN 10nF D3 LL4148 R4 1k 7 8 9 10 TM WD_OSC R3 NRES R9 10k 51k NRES TXD INH TXD INH R11 47k RXD SP_MODE 22nF 20 KL_15 10k PV GND R6 PVCC 100nF 10F R7 3.3 DIV_ON C5 RXD C3 VS + VCC PVCC SP_MODE LIN PV C6 ATA6628-EK 220pF C7 10nF ATA6630-EK V1.1 DIV_ON X2 Notes: 1. D3 and R4 are only necessary for a master node and not mounted 2. C9 is no longer needed and therefore not mounted 3. R11 is not mounted 16 Atmel ATA6628/ATA6630 9202B-AUTO-03/11 Atmel ATA6628/ATA6630 Figure 4-2. Atmel(R) ATA6628/ATA6630 Board Component Placement; Top Side, Top View Figure 4-3. Atmel ATA6628/ATA6630 Development Board; Top Side, Top View 17 9202B-AUTO-03/11 Figure 4-4. 18 Atmel(R) ATA6628/ATA6630 Development Board; Bottom Side, Top View (as if PCB was Transparent) Atmel ATA6628/ATA6630 9202B-AUTO-03/11 Atmel ATA6628/ATA6630 5. Application Examples Just to show how easy it is to develop a LIN-based application with the development board for the Atmel(R) ATA6628/ATA6630 there are some application circuits depicted on the following pages. Figure 5-1. Typical Application Circuit Ignition KL15 VBattery debug KL30 100nF + 47k 10nF 20 2.7k Wake switch WAKE GND MODE KL_15 PVCC 1 15 Atmel ATA6628 ATA6630 14 MLP 5mm x 5mm 0.65mm pitch 20 lead 12 2 3 4 13 5 11 6 LIN Microcontroller 1k 16 17 7 8 9 TM WD_OSC NRES 51k TXD INH 10 SP_ NTRIG NTRIG 10k MODE EN EN 18 PV VBATT 19 DIV_ON 10k VCC VCC 10k RXD 10F VS + 100nF Master node pull-up 100nF RXD LIN sub bus 10F 47 220pF TXD RESET ADC DIV_ON SP_MODE GND INH Note: All features active 19 9202B-AUTO-03/11 Figure 5-2. LIN Slave with Minimum External Devices VBattery KL30 VCC 22F + NTRIG WAKE GND 16 1 ATA6628/ ATA6630 2 3 15 TM 14 WD_OSC 13 QFN 5x5mm 0.65mm pitch 20 lead 4 12 5 11 Microcontroller 7 RXD LIN 6 8 9 10 SP_MODE VCC 17 PV EN EN 18 DIV_ON VCC 19 10k NRES TXD INH LIN Sub Bus 20 VBATT KL_15 VCC VS 100nF PVCC 10F + MODE 100nF R3 220pF RXD TXD RESET GND Notes: 1. No local wake-up 2. No watchdog 3. No battery voltage monitoring 20 Atmel ATA6628/ATA6630 9202B-AUTO-03/11 Atmel ATA6628/ATA6630 Figure 5-3. Application Circuit with NPN Transistor for Boosting the Voltage Regulator Ignition KL15 VBattery KL30 10F + 100nF Debug T1 MJD31C 47 22nF 47k + Master node pull-up 2.2F 100nF 2.7k WAKE GND Wake switch MODE 16 1 15 Atmel ATA6628/ ATA6630 2 3 14 13 QFN 5x5mm 0.65mm pitch 20 lead 4 12 5 11 6 LIN Microcontroller 7 8 9 TM WD_OSC 51k NRES TXD INH 10 SP_MODE NTRIG NTRIG 17 PV EN EN 18 DIV_ON VBATT VCC 19 1k 10k LIN Sub Bus 20 10 k KL_15 10k RXD + VCC 3.3 PVCC 10F VS 100nF RXD 220pF TXD RESET ADC DIV_ON SP_MODE GND INH Notes: 1. All features active No Short circuit protection of the voltage regulator output (PVCC) Note: Application examples have not been examined for series use or reliability, and no worst case scenarios have been developed. Customers who adapt any of these proposals must carry out their own tests and make sure that no negative consequences arise from the proposals. 6. Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. History 9202B-AUTO-03/11 * Section 1 "Introduction" on page 1 changed * Figure 2-2 "SOA: I_PVCC versus VS..." on page 5 changed 21 9202B-AUTO-03/11 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: (+1)(408) 441-0311 Fax: (+1)(408) 487-2600 Atmel Asia Limited Unit 01-5 & 16, 19/F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon HONG KONG Tel: (+852) 2245-6100 Fax: (+852) 2722-1369 Atmel Munich GmbH Business Campus Parkring 4 D-85748 Garching b. Munich GERMANY Tel: (+49) 89-31970-0 Fax: (+49) 89-3194621 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 JAPAN Tel: (+81) (3) 3523-3551 Fax: (+81) (3) 3523-7581 (c) 2011 Atmel Corporation. All rights reserved. / Rev.: 9202B-AUTO-03/11 Atmel(R), logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Atmel: ATA6630-EK