MiniSense 100 Analog PCB
Evaluation Circuit for Vibration Sensor
Low Power – Battery Powered
LED for Trigger
High Sensitivity
Analog and Digital Signal Access
Points
FEATURES
• Signal Conditioned Vibration
Sensor
• High Pass Filter @ 1.3Hz
• Low Pass Filter @ 177Hz
• On Board 3.3 Battery or
User Power Supply
• Both Analog and Digital
Output
pin descriptions
CHARACTERISTIC
(T=25(C)) SYMBOL MIN TYP MAX UNITS
Lower Frequency
Limit (-3dB Point)
fL3dB - 1.3 - Hz
High Frequency
Limit (-3dB Point)
fU3dB - 117 - Hz
External Supply
Voltage
+V 0.9 3.3 5.5 VDC
Supply Current Isupply - 2.8 - mA
The LDTC MiniSense 100 Analog PCB
provides a simple way to evaluate the
LDTC MiniSense 100. The unit consists of
LDTC MiniSense 100, a low-power
operation amplifier, comparator, and
DC/DC converter, and passive
components used in signal conditioning.
The sensor and circuit are assembled on a
double-sided PCB with test points,
ON/OFF switch, and 0.100” plated through
holes for easy user interface. The PCB
has adjustable gain and demonstrates the
basic capabilities of LDTC MiniSense 100
vibration sensor.
specifications
environmental characteristics
PIN NUMBER NAME DESCRIPTION
1 VDD Connect to Power Supply
2 A Analog Signal output
3 D Digital Signal output
4 GND Connect to GND
**Note: when switch set to “OFF”, PCB uses external power if
applied to (+) & (-) input pins**
APPLICATIONS
• Wake-up Sensor
• Drop Detection Sensor
• Flow Sensor
• Activity Sensor
• Alarm Trigger
MiniSense 100 Analog Rev 1 www.meas-spec.com 05/12/2009
CHARACTERISTICS
T=25(C) SYMBOL MIN TYP MAX UNITS
Operating Temperature TOP -20 - +85 ºc
Storage Temperature TS -40 - +105 ºc
Relative Humidity RH 0 - 90 %R.H
1 of 4
MiniSense 100 Analog PCB
MiniSense 100 Analog Rev 1 www.meas-spec.com 05/12/2009
electrical schematic
2 of 4
MiniSense 100 Analog PCB
MiniSense 100 Analog Rev 1 www.meas-spec.com
electrical PCB reference
electrical PCB description
frequency response
The impedance matching resistor, R5, in parallel with the 240pF sensor capacitance, establishes the
high pass input filter at approximately 1.3Hz (f=1/2πRC). After impedance buffering the LDTC signal is
DC coupled to a gain stage through a 0.7Hz high pass filter formed by C10 and R10. The amplifier
gain is set by R9, R6, and the R8 potentiometer in the OP-amp’s feedback loop: Gain=1+
[R9/(R8+R6)] with a max gain of 20dB, min gain of 6dB. C6 in parallel with R9 in the feedback loop
form a low pass filter with a corner frequency of 177Hz.
After signal conditioning the analog voltage is buffered for output and also fed into a comparator. R15
& R4 set the threshold voltage. If the amplified signal exceeds the threshold voltage, the comparator
output will be pulled low through a 4.7K resistor and the PNP transistor will turn on the LED. The
reference voltage, VREF, is 1.65V, or half of the internal 3.3V rail. The on board 3.3V battery and
external power are converted to a 5V supply using a DC-DC converter.
Minisense 100 vibration sensor frequency response
05/12/2009
3 of 4
MiniSense 100 Analog PCB
MiniSense 100 vibration sensor Analog PCB Acceleration Response
The information in this sheet has been carefully reviewed and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Furthermore, this information does no
t
convey to the purchaser of such devices any license under the patent rights to the manufacturer. Measurement Specialties, Inc. reserves the right to make changes without further notic
e
to any product herein. Measurement Specialties, Inc. makes no warranty, representation or guarantee regarding the suitability of its product for any particular purpose, nor doe
s
Measurement Specialties, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation
consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters must be validated for each customer application b
y
customer’s technical experts. Measurement Specialties, Inc. does not convey any license under its patent rights nor the rights of others.
ordering information
Description Part Number
MiniSense 100 Analog PCB 1007215
North America
Measurement Specialties, Inc.
1000 Lucas Way
Hampton, VA 23666
Sales and Customer Service
Tel: +1-800-745-8008 or
+1-757-766-1500
Fax: +1-757-766-4297
Technical Support
Email: piezo@meas-spec.com
Europe
MEAS Deutschland GmbH
Hauert 13
44227 Dortmund
Germany
Sales and Customer Service
Tel: +49 (0)231 9740 21
Technical Support
Tel: +49 (0)6074 862822
Email: piezoeurope@meas-spec.com
Asia
Measurement Specialties (China), Ltd.
No. 26 Langshan Road
ShenZhen High-Tech Park (North)
Nanshan District
ShenZhen, China 518107
Sales and Customer Service
Tel: +86 755 3330 5088
Technical Support
Email: piezo@meas-spec.com
MiniSense 100 Analog Rev 1 www.meas-spec.com 05/12/2009
4 of 4
