a FEATURES High Speed 50 MHz Unity Gain Stable Operation 300 V/ms Slew Rate 120 ns Settling Time Drives Unlimited Capacitive Loads Excellent Video Performance 0.04% Differential Gain @ 4.4 MHz 0.198 Differential Phase @ 4.4 MHz Good DC Performance 2 mV max Input Offset Voltage 15 mV/8C Input Offset Voltage Drift Available in Tape and Reel in Accordance with EIA-481A Standard Low Power Only 10 mA Total Supply Current for Both Amplifiers 5 V to 15 V Supplies High Speed, Low Power Dual Op Amp AD827 CONNECTION DIAGRAMS 8-Lead Plastic (N) and Cerdip (Q) Packages 16-Lead Small Outline (R) Package 20-Lead LCC (E) Package PRODUCT DESCRIPTION The AD827 is a dual version of Analog Devices' industrystandard AD847 op amp. Like the AD847, it provides high speed, low power performance at low cost. The AD827 achieves a 300 V/s slew rate and 50 MHz unity-gain bandwidth while consuming only 100 mW when operating from 5 volt power supplies. Performance is specified for operation using 5 V to 15 V power supplies. The AD827 offers an open-loop gain of 3,500 V/V into 500 loads. It also features a low input voltage noise of 15 nV/Hz, and a low input offset voltage of 2 mV maximum. Commonmode rejection ratio is a minimum of 80 dB. Power supply rejection ratio is maintained at better than 20 dB with input frequencies as high as 1 MHz, thus minimizing noise feedthrough from switching power supplies. The AD827 is also ideal for use in demanding video applications, driving coaxial cables with less than 0.04% differential gain and 0.19 differential phase errors for 643 mV p-p into a 75 reverse terminated cable. The AD827 is also useful in multichannel, high speed data conversion systems where its fast (120 ns to 0.1%) settling time is of importance. In such applications, the AD827 serves as an input buffer for 8-bit to 10-bit A/D converters and as an output amplifier for high speed D/A converters. APPLICATION HIGHLIGHTS 1. Performance is fully specified for operation using 5 V to 15 V supplies. 2. A 0.04% differential gain and 0.19 differential phase error at the 4.4 MHz color subcarrier frequency, together with its low cost, make it ideal for many video applications. 3. The AD827 can drive unlimited capacitive loads, while its 30 mA output current allows 50 and 75 reverseterminated loads to be driven. 4. The AD827's 50 MHz unity-gain bandwidth makes it an ideal candidate for multistage active filters. 5. The AD827 is available in 8-lead plastic mini-DIP and cerdip, 20-lead LCC, and 16-lead SOIC packages. Chips and MIL-STD-883B processing are also available. REV. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 2002 AD827-SPECIFICATIONS (@ T = +25C, unless otherwise noted.) A Model Conditions DC PERFORMANCE Input Offset Voltage1 Min 5 V TMIN to TMAX TMIN to TMAX Offset Voltage Drift Input Bias Current TMIN to TMAX Input Offset Current TMIN to TMAX Offset Current Drift Common-Mode Rejection Ratio VS VCM = 2.5 V VCM = 12 V TMIN to TMAX Power Supply Rejection Ratio AD827J Typ Max 0.5 15 V 5 V to 15 V 5 V to 15 V 15 3.3 5 V to 15 V 50 5 V to 15 V 5 V 15 V 5 V to 15 V 5 V to 15 V TMIN to TMAX 78 78 75 75 72 0.5 95 95 86 AD827A/S Min Typ Max 2 3.5 4 6 0.3 15 3.3 7 8.2 300 400 50 80 80 75 75 72 0.5 95 95 86 2 4 4 6 7 9.5 300 400 Unit mV mV mV mV V/C A A nA nA nA/C dB dB dB dB dB Open-Loop Gain VO = 2.5 V RLOAD = 500 TMIN to TMAX RLOAD = 150 VOUT = 10 V RLOAD = 1 k TMIN to TMAX MATCHING CHARACTERISTICS Input Offset Voltage Crosstalk f = 5 MHz DYNAMIC PERFORMANCE Unity-Gain Bandwidth Full Power Bandwidth2 Slew Rate3 Settling Time to 0.1% Phase Margin Differential Gain Error Differential Phase Error Input Voltage Noise Input Current Noise Input Common-Mode Voltage Range VO = 5 V p-p, RLOAD = 500 VO = 20 V p-p, RLOAD = 1 k RLOAD = 500 RLOAD = 1 k AV = -1 -2.5 V to +2.5 V -5 V to +5 V CLOAD = 10 pF RLOAD = 1 k f = 4.4 MHz f = 4.4 MHz f = 10 kHz f = 10 kHz 5 V 2 1 1.6 3 1.5 Short-Circuit Current Limit 3.5 1.6 V/mV V/mV V/mV 5.5 3 1.5 5.5 V/mV V/mV 5 V 5 V 0.4 85 0.2 85 mV dB 5 V 15 V 35 50 35 50 MHz MHz 5 V 12.7 12.7 MHz 15 V 5 V 15 V 4.7 200 300 4.7 200 300 MHz V/s V/s 5 V 15 V 15 V 65 120 65 120 ns ns 50 0.04 0.19 15 1.5 50 0.04 0.19 15 1.5 Degrees % Degrees nV/Hz pA/Hz +4.3 -3.4 +14.3 -13.4 3.6 3.0 13.3 12.2 32 +4.3 -3.4 +14.3 -13.4 3.6 3.0 13.3 12.2 32 V V V V V V V V mA 300 1.5 k pF 15 V 15 V 15 V 15 V 5 V RLOAD = 500 RLOAD = 150 RLOAD = 1 k RLOAD = 500 2 1 15 V 15 V Output Voltage Swing 3.5 5 V 5 V 15 V 15 V 5 V to 15 V INPUT CHARACTERISTICS Input Resistance Input Capacitance 3.0 2.5 12 10 300 1.5 -2- 3.0 2.5 12 10 REV. C AD827 Model Conditions OUTPUT RESISTANCE Open Loop POWER SUPPLY Operating Range Quiescent Current VS Min Min AD827A/S Typ Max 15 5 V TMIN to TMAX AD827J Typ Max 4.5 10 15 V 10.5 TMIN to TMAX TRANSISTOR COUNT 18 13 16 13.5 16.5 4.5 10 10.5 92 Unit 15 18 13 16.5/17.5 13.5 17/18 V mA mA mA mA 92 NOTES 1 Offset voltage for the AD827 is guaranteed after power is applied and the device is fully warmed up. All other specifications are measured using high speed test equipment, approximately 1 second after power is applied. 2 Full Power Bandwidth = Slew Rate/2 VPEAK. 3 Gain = +1, rising edge. All min and max specifications are guaranteed. Specifications subject to change without notice. ABSOLUTE MAXIMUM RATINGS 1 ORDERING GUIDE Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Internal Power Dissipation2 Plastic (N) Package (Derate at 10 mW/C) . . . . . . . . 1.5 W Cerdip (Q) Package (Derate at 8.7 mW/C) . . . . . . . 1.3 W Small Outline (R) Package (Derate at 10 mW/C) . . . 1.5 W LCC (E) Package (Derate at 6.7 mW/C) . . . . . . . . . 1.0 W Input Common-Mode Voltage . . . . . . . . . . . . . . . . . . . . . VS Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Output Short Circuit Duration3 . . . . . . . . . . . . . . . . Indefinite Storage Temperature Range (N, R) . . . . . . . -65C to +125C Storage Temperature Range (Q) . . . . . . . . . -65C to +150C Operating Temperature Range AD827J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 70C AD827A . . . . . . . . . . . . . . . . . . . . . . . . . . . -40C to +85C AD827S . . . . . . . . . . . . . . . . . . . . . . . . . . -55C to +125C Lead Temperature Range (Soldering to 60 sec) . . . . . . . . . . . . . . . . . . . . . . . . . 300C Temperature Range Package Description Package Option AD827JN AD827JR AD827AQ AD827SQ AD827SQ/883B 5962-9211701MPA AD827SE/883B 5962-9211701M2A AD827JR-REEL AD827JChips AD827SChips 0C to +70C 0C to +70C -40C to +85C -55C to +125C -55C to +125C -55C to +125C -55C to +125C -55C to +125C 0C to +70C 0C to +70C -55C to +125C 8-Lead Plastic DIP 16-Lead Plastic SO 8-Lead Cerdip 8-Lead Cerdip 8-Lead Cerdip 8-Lead Cerdip 20-Lead LCC 20-Lead LCC Tape & Reel Die Die N-8 R-16 Q-8 Q-8 Q-8 Q-8 E-20A E-20A METALLIZATION PHOTOGRAPH Contact factory for latest dimensions. Dimensions shown in inches and (mm). Substrate is connected to V+. NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum ratings for extended periods may affect device reliability. 2 Maximum internal power dissipation is specified so that T J does not exceed 175C at an ambient temperature of 25C. Thermal Characteristics: MiniDIP: JA = 100C/W; JC = 33C/ W Cerdip: JA = 110C/W; JC = 30C/W 16-Lead Small Outline Package: JA = 100C/W 20-Lead LCC: JA = 150C/W; JC = 35C/W 3 Indefinite short circuit duration is only permissible as long as the absolute maximum power rating is not exceeded. REV. C Model -3- AD827 -Typical Performance Characteristics 20 OUTPUT VOLTAGE SWING - Volts 20 INPUT COMMON-MODE RANGE - Volts (@ +25C & 15 V, unless otherwise noted) 15 +VIN 10 -VIN 5 15 +VOUT 10 -VOUT RLOAD = 1k 5 0 0 0 5 10 15 SUPPLY VOLTAGE Volts 20 0 5 10 15 SUPPLY VOLTAGE Volts 20 Figure1. InputCommon-Mode Range vs. Supply Voltage Figure 2. Output Voltage Swing vs. Supply Voltage Figure 3. Output Voltage Swing vs. Load Resistance Figure 4. Quiescent Current vs. Supply Voltage Figure 5. Input Bias Current vs. Temperature Figure 6. Closed-Loop Output Impedance vs. Frequency, Gain = +1 Figure 8. Short-Circuit Current Limit vs. Temperature Figure 9. Gain Bandwidth vs. Temperature QUIESCENT CURRENT - mA 14 12 VS = 15V 10 VS = 5V 8 0 -60 -40 -20 0 40 60 20 80 TEMPERATURE - C 100 120 140 Figure 7. Quiescent Current vs. Temperature -4- REV. C AD827 Figure 10. Open-Loop Gain and Phase Margin vs. Frequency Figure 13. Common-Mode Rejection Ratio vs. Frequency Figure 11. Open-Loop Gain vs. Load Resistance Figure 12. Power Supply Rejection Ratio vs. Frequency Figure 15. Output Swing and Error vs. Settling Time Figure 14. Large Signal Frequency Response 400 RISE 350 SLEW RATE - Volts/s AV = +1 SLEW RATE 10 - 90% 300 FALL VS = 15V 250 RISE 200 VS = 5V FALL 150 100 -60 -40 Figure 16. Harmonic Distortion vs. Frequency REV. C Figure 17. Input Voltage Noise Spectral Density -5- -20 0 20 40 60 80 TEMPERATURE - C 100 120 140 Figure 18. Slew Rate vs. Temperature AD827 Figure 20. Crosstalk Test Circuit Figure 19. Crosstalk vs. Frequency INPUT PROTECTION PRECAUTIONS An input resistor (resistor RIN of Figure 21a) is recommended in circuits where the input common-mode voltage to the AD827 may exceed (on a transient basis) the positive supply voltage. This resistor provides protection for the input transistors by limiting the maximum current that can be forced into their bases. For high performance circuits, it is recommended that a second resistor (RB in Figures 21a and 22a) be used to reduce biascurrent errors by matching the impedance at each input. This resistor reduces the error caused by offset voltages by more than an order of magnitude. Figure 21a. Follower Connection Figure 21b. Follower Large Signal Pulse Response Figure 21c. Follower Small Signal Pulse Response Figure 22a. Inverter Connection Figure 22b. Inverter Large Signal Pulse Response Figure 22c. Inverter Small Signal Pulse Response -6- REV. C AD827 VIDEO LINE DRIVER A HIGH SPEED THREE OP AMP INSTRUMENTATION AMPLIFIER CIRCUIT The AD827 functions very well as a low cost, high speed line driver for either terminated or unterminated cables. Figure 23 shows the AD827 driving a doubly terminated cable in a follower configuration. The instrumentation amplifier circuit shown in Figure 24 can provide a range of gains. Table II details performance. +VS +VS TRIM FOR BEST SETTLING TIME 0.1F 2 - 8pF -VIN 0.1 F VIN 50 3 8 + 1/2 2 AD827 - RBT 1/2 AD827 2k 1 +VS VOUT 50 0.1F 1k RT 50 0.1 F 2k 500 TRIM FOR OPTIMUM BANDWIDTH 7 - 15 pF RG 2 6 AD847 3 + 4 0.1F 2k -VS 7 - 3pF VOUT 2k RL 2k 6 CC 1k - 1/2 5 AD827 + 4 500 +VIN 7 CIRCUIT GAIN = 2000 + 1 RG 0.1F NOTE: PINOUT SHOWN IS FOR MINIDIP PACKAGE -VS Figure 23. A Video Line Driver -VS Figure 24. A High Bandwidth Three Op Amp Instrumentation Amplifier The termination resistor, RT, (when equal to the cable's characteristic impedance) minimizes reflections from the far end of the cable. While operating from 5 V supplies, the AD827 maintains a typical slew rate of 200 V/s, which means it can drive a 1 V, 30 MHz signal into a terminated cable. Table II. Performance Specifications for the Three Op Amp Instrumentation Amplifier Gain RG Small Signal Bandwidth @ 1 V p-p Output 1 2 10 100 Open 2k 226 20 16.1 MHz 14.7 MHz 4.9 MHz 660 kHz Table I. Video Line Driver Performance Summary VIN* VSUPPLY CC -3 dB BW Overshoot 0 dB or 500 mV Step 0 dB or 500 mV Step 0 dB or 500 mV Step 0 dB or 500 mV Step 0 dB or 500 mV Step 0 dB or 500 mV Step 15 15 15 5 5 5 20 pF 15 pF 0 pF 20 pF 15 pF 0 pF 23 MHz 21 MHz 13 MHz 18 MHz 16 MHz 11 MHz 4% 0% 0% 2% 0% 0% *-3 dB bandwidth numbers are for the 0 dBm signal input. Overshoot numbers are the percent overshoot of the 1 V step input. A back-termination resistor (RBT, also equal to the characteristic impedance of the cable) may be placed between the AD827 output and the cable input, in order to damp any reflected signals caused by a mismatch between RT and the cable's characteristic impedance. This will result in a flatter frequency response, although this requires that the op amp supply 2 V to the output in order to achieve a 1 V swing at resistor RT. REV. C -7- AD827 A TWO-CHIP VOLTAGE-CONTROLLED AMPLIFIER (VCA) WITH EXPONENTIAL RESPONSE Voltage-controlled amplifiers are often used as building blocks in automatic gain control systems. Figure 25 shows a two-chip VCA built using the AD827 and the AD539, a dual, currentoutput multiplier. As configured, the circuit has its two between the CH1 output and Z1, the other between the CH1 output and W1. Likewise, in the CH2 multiplier, one of the feedback resistors is connected between CH2 and Z2 and the other is connected between CH2 and Z2. In Figure 25, Z1 and W1 are tied together, as are Z2 and W2, providing a 3 k feedback resistor for the op amp. The 2 pF capacitors connected between the AD539's W1 and CH1 and W2 and CH2 pins are in parallel with the feedback resistors and thus reduce peaking in the VCA's frequency response. Increasing the values of C3 and C4 can further reduce the peaking at the expense of reduced bandwidth. The 1.25 mA full-scale output current of the AD539 and the 3 k feedback resistor set the full-scale output voltage of each multiplier at 3.25 V p-p. Current limiting in the AD827 (typically 30 mA) limits the output voltage in this application to about 3 V p-p across a 100 load. Driving a 50 reverse-terminated load divides this value by two, limiting the maximum signal delivered to a 50 load to about 1.5 V p-p, which suffices for video signal levels. The dynamic range of this circuit is approximately 55 dB and is primarily limited by feedthrough at low input levels and by the maximum output voltage at high levels. Figure 25. A Wide Range Voltage-Controlled Amplifier Circuit multipliers connected in series. They could also be placed in parallel with an increase in bandwidth and a reduction in gain. The gain of the circuit is controlled by VX, which can range from 0 to 3 V dc. Measurements show that this circuit easily supplies 2 V p-p into a 100 load while operating from 5 V supplies. The overall bandwidth of the circuit is approximately 7 MHz with 0.5 dB of peaking. Each half of the AD827 serves as an I/V converter and converts the output current of one of the two multipliers in the AD539 into an output voltage. Each of the AD539's two multipliers contains two internal 6 k feedback resistors; one is connected Guidelines for Grounding and Bypassing When designing practical high frequency circuits using the AD827, some special precautions are in order. Both short interconnection leads and a large ground plane are needed whenever possible to provide low resistance, low inductance circuit paths. One should remember to minimize the effects of capacitive coupling between circuits. Furthermore, IC sockets should be avoided. Feedback resistors should be of a low enough value that the time constant formed with stray circuit capacitances at the amplifier summing junction will not limit circuit performance. As a rule of thumb, use feedback resistor values that are less than 5 k. If a larger resistor value is necessary, a small (<10 pF) feedback capacitor in parallel with the feedback resistor may be used. The use of 0.1 F ceramic disc capacitors is recommended for bypassing the op amp's power supply leads. -8- REV. C AD827 OUTLINE DIMENSIONS 8-Lead Plastic Dual-in-Line Package [PDIP] (N-8) 8-Lead Ceramic DIP-Glass Hermetic Seal Package [CERDIP] (Q-8) Dimensions shown in millimeters and (inches) Dimensions shown in millimeters and (inches) 0.13 (0.0051) 1.40 (0.0551) MAX MIN 10.92 (0.4299) 8.84 (0.3480) 8 8 5 1 7.11 (0.2799) 6.10 (0.2402) 5 7.87 (0.3089) 5.59 (0.2201) PIN 1 4 1 PIN 1 8.25 (0.3248) 7.62 (0.3000) 2.54 (0.1000) BSC 2.54 (0.1000) BSC 8.13 (0.3201) 7.37 (0.2902) 10.29 (0.4051) MAX 1.52 (0.0598) 0.38 (0.0150) ( 3.30 (0.1299) MIN 5.33 (0.2098) MAX 4.06 (0.1598) 2.93 (0.1154) 0.56 (0.0220) 0.36 (0.0142) 4 4.95 (0.1949) 2.93 (0.1154) 5.08 (0.2000) MAX 0.38 (0.0150) 0.20 (0.0079) 5.08 (0.2000) 3.18 (0.1252) SEATING PLANE 1.77 (0.0697) 1.15 (0.0453) 0.58 (0.0228) 0.36 (0.0142) CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 1.52 (0.0600) 0.38 (0.0150) 3.81 (0.1500) MIN SEATING 1.78 (0.0701) PLANE 0.76 (0.0299) 0.38 (0.0150) 0.20 (0.0079) 15 0 CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 20-Terminal Ceramic Leadless Chip Carrier [LCC] (E-20A) 16-Lead Standard Small Outline Package [SOIC] Wide Body (R-16) Dimensions shown in millimeters and (inches) Dimensions shown in millimeters and (inches) 2.54 (0.1000) 1.63 (0.0642) 10.50 (0.4134) 10.10 (0.3976) 9.09 9.09 (0.3579) 8.69 (0.3421) (0.3579) MAX SQ SQ 7.60 (0.2992) 7.40 (0.2913) 8 1 1.27 (0.0500) BSC 10.65 (0.4193) 10.00 (0.3937) 2.24 (0.0882) 1.37 (0.0539) 2.65 (0.1043) 2.35 (0.0925) 0.75 (0.0295) 45 0.25 (0.0098) 0.51 (0.0201) 0.33 (0.0130) SEATING PLANE 0.32 (0.0126) 0.23 (0.0091) 8 0 1.27 (0.0500) 0.40 (0.0157) CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN COMPLIANT TO JEDEC STANDARDS MS-013AA REV. C 2.54 (0.1000) BSC 3 4 0.28 (0.0110) 0.18 (0.0071) R TYP 1.91 (0.0752) REF 1.40 (0.0551) 1.14 (0.0449) 1 BOTTOM VIEW 14 13 0.38 (0.0150) MIN 0.71 (0.0278) 0.56 (0.0220) 1.27 (0.0500) BSC 8 9 45 TYP 3.81 (0.1500) BSC CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 0.30 (0.0118) 0.10 (0.0039) COPLANARITY 0.10 5.08 (0.2000) BSC 19 18 20 9 16 PIN 1 1.91 (0.0752) REF 2.41 (0.0949) 1.90 (0.0748) -9- AD827 Revision History Location Page 8/02--Data Sheet changed from REV. B to REV. C. Updated Outline Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 -10- REV. C -11- -12- PRINTED IN U.S.A. C00878-0-8/02(C)