Features * Fast Read Access Time - 70 ns * 5-volt Only Reprogramming * Sector Program Operation * * * * * * * * * * - Single Cycle Reprogram (Erase and Program) - 1024 Sectors (256 Bytes/Sector) - Internal Address and Data Latches for 256 Bytes Internal Program Control and Timer Hardware and Software Data Protection Two 8K Bytes Boot Blocks with Lockout Fast Sector Program Cycle Time - 10 ms DATA Polling for End of Program Detection Low Power Dissipation - 40 mA Active Current - 100 A CMOS Standby Current Typical Endurance > 10,000 Cycles Single 5V 10% Supply CMOS and TTL Compatible Inputs and Outputs Commercial and Industrial Temperature Ranges 2-megabit (256K x 8) 5-volt Only Flash Memory AT29C020 Description The AT29C020 is a 5-volt-only in-system Flash programmable and erasable read-only memory (PEROM). Its 2 megabits of memory is organized as 262,144 bytes. Manufactured with Atmel's advanced nonvolatile CMOS technology, the device offers access times to 70 ns with power dissipation of just 220 mW over the commercial temperature range. When the device is deselected, the CMOS standby current is less than 100 A. Device endurance is such that any sector can typically be written to in excess of 10,000 times. Pin Configurations DIP Top View Pin Name Function A0 - A17 Addresses CE Chip Enable OE Output Enable WE Write Enable I/O0 - I/O7 Data Inputs/Outputs NC No Connect NC A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 GND TSOP Top View Type 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 VCC WE A17 A14 A13 A8 A9 A11 OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 GND I/O2 I/O1 I/O0 A0 A1 A2 A3 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 5 6 7 8 9 10 11 12 13 29 28 27 26 25 24 23 22 21 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 I/O1 I/O2 GND I/O3 I/O4 I/O5 I/O6 A11 A9 A8 A13 A14 A17 WE VCC NC A16 A15 A12 A7 A6 A5 A4 4 3 2 1 32 31 30 A12 A15 A16 NC VCC WE A17 PLCC Top View A14 A13 A8 A9 A11 OE A10 CE I/O7 Rev. 0291N-FLASH-07/02 1 To allow for simple in-system reprogrammability, the AT29C020 does not require high input voltages for programming. Five-volt-only commands determine the operation of the device. Reading data out of the device is similar to reading from an EPROM. Reprogramming the AT29C020 is performed on a sector basis; 256 bytes of data are loaded into the device and then simultaneously programmed. During a reprogram cycle, the address locations and 256 bytes of data are internally latched, freeing the address and data bus for other operations. Following the initiation of a program cycle, the device will automatically erase the sector and then program the latched data using an internal control timer. The end of a program cycle can be detected by DATA polling of I/O7. Once the end of a program cycle has been detected, a new access for a read or program can begin. Block Diagram Device Operation READ: The AT29C020 is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state whenever CE or OE is high. This dual-line control gives designers flexibility in preventing bus contention. BYTE LOAD: Byte loads are used to enter the 256 bytes of a sector to be programmed or the software codes for data protection. A byte load is performed by applying a low pulse on the WE or CE input with CE or WE low (respectively) and OE high. The address is latched on the falling edge of CE or WE, whichever occurs last. The data is latched by the first rising edge of CE or WE. PROGRAM: The device is reprogrammed on a sector basis. If a byte of data within a sector is to be changed, data for the entire sector must be loaded into the device. Any byte that is not loaded during the programming of its sector will be indeterminate. Once the bytes of a sector are loaded into the device, they are simultaneously programmed during the internal programming period. After the first data byte has been loaded into the device, successive bytes are entered in the same manner. Each new byte to be programmed must have its high-to-low transition on WE (or CE) within 150 s of the low-to-high transition of WE (or CE) of the preceding byte. If a high-to-low transition is not detected within 150 s of the last low-to-high transition, the load period will end and the internal programming period will start. A8 to A17 specify the sector address. The sector address must be valid during each high-to-low transition of WE (or CE). A0 to A7 specify the byte address within the sector. The bytes may be loaded in any order; sequential loading is not required. Once a programming operation has been initiated, and for the duration of tWC, a read operation will effectively be a polling operation. 2 AT29C020 0291N-FLASH-07/02 AT29C020 SOFTWARE DATA PROTECTION: A software controlled data protection feature is available on the AT29C020. Once the software protection is enabled a software algorithm must be issued to the device before a program may be performed. The software protection feature may be enabled or disabled by the user; when shipped from Atmel, the software data protection feature is disabled. To enable the software data protection, a series of three program commands to specific addresses with specific data must be performed. After the software data protection is enabled the same three program commands must begin each program cycle in order for the programs to occur. All software program commands must obey the sector program timing specifications. Once set, the software data protection feature remains active unless its disable command is issued. Power transitions will not reset the software data protection feature; however, the software feature will guard against inadvertent program cycles during power transitions. After setting SDP, any attempt to write to the device without the 3-byte command sequence will start the internal write timers. No data will be written to the device; however, for the duration of tWC, a read operation will effectively be a polling operation. After the software data protection's 3-byte command code is given, a sector of data is loaded into the device using the sector program timing specifications. HARDWARE DATA PROTECTION: Hardware features protect against inadvertent programs to the AT29C020 in the following ways: (a) VCC sense - if VCC is below 3.8V (typical), the program function is inhibited; (b) VCC power on delay - once VCC has reached the V CC sense level, the device will automatically time out 5 ms (typical) before programming; (c) Program inhibit - holding any one of OE low, CE high or WE high inhibits program cycles; and (d) Noise filter - pulses of less than 15 ns (typical) on the WE or CE inputs will not initiate a program cycle. PRODUCT IDENTIFICATION: The product identification mode identifies the device and manufacturer as Atmel. It may be accessed by hardware or software operation. The hardware operation mode can be used by an external programmer to identify the correct programming algorithm for the Atmel product. In addition, users may wish to use the software product identification mode to identify the part (i.e. using the device code), and have the system software use the appropriate sector size for program operations. In this manner, the user can have a common board design for 256K to 4-megabit densities and, with each density's sector size in a memory map, have the system software apply the appropriate sector size. For details, see Operating Modes (for hardware operation) or Software Product Identification. The manufacturer and device code is the same for both modes. DATA POLLING: The AT29C020 features DATA polling to indicate the end of a program cycle. During a program cycle an attempted read of the last byte loaded will result in the complement of the loaded data on I/O7. Once the program cycle has been completed, true data is valid on all outputs and the next cycle may begin. DATA polling may begin at any time during the program cycle. TOGGLE BIT: In addition to DATA polling the AT29C020 provides another method for determining the end of a program or erase cycle. During a program or erase operation, successive attempts to read data from the device will result in I/O6 toggling between one and zero. Once the program cycle has completed, I/O6 will stop toggling and valid data will be read. Examining the toggle bit may begin at any time during a program cycle. OPTIONAL CHIP ERASE MODE: The entire device can be erased by using a 6-byte software code. Please see Software Chip Erase application note for details. 3 0291N-FLASH-07/02 BOOT BLOCK PROGRAMMING LOCKOUT: The AT29C020 has two designated memory blocks that have a programming lockout feature. This feature prevents programming of data in the designated block once the feature has been enabled. Each of these blocks consists of 8K bytes; the programming lockout feature can be set independently for either block. While the lockout feature does not have to be activated, it can be activated for either or both blocks. These two 8K memory sections are referred to as boot blocks. Secure code which will bring up a system can be contained in a boot block. The AT29C020 blocks are located in the first 8K bytes of memory and the last 8K bytes of memory. The boot block programming lockout feature can therefore support systems that boot from the lower addresses of memory or the higher addresses. Once the programming lockout feature has been activated, the data in that block can no longer be erased or programmed; data in other memory locations can still be changed through the regular programming methods. To activate the lockout feature, a series of seven program commands to specific addresses with specific data must be performed. Please see Boot Block Lockout Feature Enable Algorithm. If the boot block lockout feature has been activated on either block, the chip erase function will be disabled. BOOT BLOCK LOCKOUT DETECTION: A software method is available to determine whether programming of either boot block section is locked out. See Software Product Identification Entry and Exit sections. When the device is in the software product identification mode, a read from location 00002H will show if programming the lower address boot block is locked out while reading location 3FFF2H will do so for the upper boot block. If the data is FE, the corresponding block can be programmed; if the data is FF, the program lockout feature has been activated and the corresponding block cannot be programmed. The software product identification exit mode should be used to return to standard operation. Absolute Maximum Ratings* Temperature Under Bias................................ -55C to +125C Storage Temperature ..................................... -65C to +150C All Input Voltages (including NC Pins) with Respect to Ground ...................................-0.6V to +6.25V All Output Voltages with Respect to Ground .............................-0.6V to VCC + 0.6V *NOTICE: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on OE with Respect to Ground ...................................-0.6V to +13.5V 4 AT29C020 0291N-FLASH-07/02 AT29C020 DC and AC Operating Range Operating Temperature (Case) Com. Ind. VCC Power Supply AT29C020-70 AT29C020-90 AT29C020-10 AT29C020-12 AT29C020-15 0C - 70C 0C - 70C 0C - 70C 0C - 70C 0C - 70C -40C - 85C -40C - 85C -40C - 85C -40C - 85C -40C - 85C 5V 10% 5V 10% 5V 10% 5V 10% 5V 10% Not recommended for New Designs. Note: Operating Modes Mode CE OE WE Ai I/O Read VIL VIL VIH Ai DOUT Program (2) VIL VIH VIL Ai DIN 5V Chip Erase VIL VIH VIL Ai X X Standby/Write Inhibit (1) VIH X Program Inhibit X X VIH Program Inhibit X VIL X Output Disable X VIH X VIL VIL VIH High Z High Z Product Identification Hardware A1 - A17 = VIL, A9 = VH,(3) A0 = VIL A1 - A17 = VIL, A9 = VH, A0 = VIH Software(5) Notes: 1. 2. 3. 4. 5. Manufacturer Code(4) Device Code(4) A0 = VIL Manufacturer Code(4) A0 = VIH Device Code(4) X can be VIL or VIH. Refer to AC Programming Waveforms. VH = 12.0V 0.5V. Manufacturer Code: 1F, Device Code: DA. See details under Software Product Identification Entry/Exit. DC Characteristics Symbol Parameter Condition ILI Input Load Current ILO ISB1 Min Max Units VIN = 0V to VCC 10 A Output Leakage Current VI/O = 0V to VCC 10 A VCC Standby Current CMOS CE = V CC - 0.3V to VCC Com. 100 A Ind. 300 A ISB2 VCC Standby Current TTL CE = 2.0V to VCC 3 mA ICC VCC Active Current f = 5 MHz; IOUT = 0 mA 40 mA VIL Input Low Voltage 0.8 V VIH Input High Voltage VOL Output Low Voltage IOL = 2.1 mA VOH1 Output High Voltage IOH = -400 A 2.4 V VOH2 Output High Voltage CMOS IOH = -100 A; VCC = 4.5V 4.2 V 2.0 V 0.45 V 5 0291N-FLASH-07/02 AC Read Characteristics AT29C020-90 Symbol Parameter tACC Address to Output Delay AT29C020-90 AT29C020-10 Min Max Min Max 0 70 0 90 100 90 100 Min Max AT29C020-12 Min AT29C020-15 Max Units 120 150 ns 120 150 ns Max Min (1) CE to Output Delay tOE(2) OE to Output Delay 0 40 0 40 0 50 0 50 0 70 ns CE or OE to Output Float 0 25 0 25 0 25 0 30 0 40 ns Output Hold from OE, CE or Address, whichever occurred first 0 tCE tDF (3)(4) tOH Note: 70 0 0 0 0 ns Not recommended for New Designs. AC Read Waveforms(1)(2)(3)(4) Notes: 6 1. CE may be delayed up to tACC - tCE after the address transition without impact on tACC. 2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE or by tACC - tOE after an address change without impact on tACC. 3. tDF is specified from OE or CE whichever occurs first (CL = 5 pF). 4. This parameter is characterized and is not 100% tested. AT29C020 0291N-FLASH-07/02 AT29C020 Input Test Waveforms and Measurement Level tR, t F < 5 ns Output Test Load Pin Capacitance f = 1 MHz, T = 25C(1) Symbol Typ Max Units Conditions CIN 4 6 pF VIN = 0V COUT 8 12 pF VOUT = 0V Note: 1. This parameter is characterized and is not 100% tested. 7 0291N-FLASH-07/02 AC Byte Load Characteristics Symbol Parameter Min Max Units tAS, tOES Address, OE Set-up Time 0 ns tAH Address Hold Time 50 ns tCS Chip Select Set-up Time 0 ns tCH Chip Select Hold Time 0 ns tWP Write Pulse Width (WE or CE) 90 ns tDS Data Set-up Time 50 ns tDH, tOEH Data, OE Hold Time 0 ns tWPH Write Pulse Width High 100 ns AC Byte Load Waveforms WE Controlled CE Controlled 8 AT29C020 0291N-FLASH-07/02 AT29C020 Program Cycle Characteristics Symbol Parameter Min Max Units tWC Write Cycle Time 10 ms tAS Address Set-up Time 0 ns tAH Address Hold Time 50 ns tDS Data Set-up Time 50 ns tDH Data Hold Time 0 ns tWP Write Pulse Width 90 ns tBLC Byte Load Cycle Time tWPH Write Pulse Width High 150 100 s ns Program Cycle Waveforms(1)(2)(3) Notes: 1. A8 through A17 must specify the sector address during each high-to-low transition of WE (or CE). 2. OE must be high when WE and CE are both low. 3. All words that are not loaded within the sector being programmed will be indeterminate. 9 0291N-FLASH-07/02 Software Data Protection Enable Algorithm() Software Data Protection Disable Algorithm() LOAD DATA AA TO ADDRESS 5555 LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA A0 TO ADDRESS 5555 WRITES ENABLED LOAD DATA 80 TO ADDRESS 5555 LOAD DATA TO PAGE (128 BYTES)(4) ENTER DATA PROTECT STATE(2) LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 20 TO ADDRESS 5555 EXIT DATA PROTECT STATE(3) LOAD DATA TO PAGE (128 BYTES)(4) Notes: 1. 2. 3. 4. Data Format: I/O7 - I/O0 (Hex); Address Format: A14 - A0 (Hex). Data Protect state will be activated at end of program cycle. Data Protect state will be deactivated at end of program period. 256 bytes of data MUST BE loaded. Software Protected Program Cycle Waveform(1)(4)(5) Notes: 10 1. A8 through A17 must specify the sector address during each high-to-low transition of WE (or CE) after the software code has been entered. 4. OE must be high when WE and CE are both low. 5. All bytes that are not loaded within the sector being programmed will be indeterminate. AT29C020 0291N-FLASH-07/02 AT29C020 Data Polling Characteristics(1) Symbol Parameter tDH Data Hold Time tOEH OE Hold Time Min Max OE to Output Delay tWR Write Recovery Time Units 10 ns 10 ns (2) tOE Notes: Typ ns 0 ns 1. These parameters are characterized and not 100% tested. 2. See tOE spec in AC Read Characteristics. Data Polling Waveforms Toggle Bit Characteristics(1) Symbol Parameter tDH Data Hold Time tOEH OE Hold Time Min OE to Output Delay tOEHP OE High Pulse tWR Write Recovery Time Notes: Max Units 10 ns 10 ns (2) tOE Typ ns 150 ns 0 ns 1. These parameters are characterized and not 100% tested. 2. See tOE spec in AC Read Characteristics. Toggle Bit Waveforms(1)(2)(3) Notes: 1. Toggling either OE or CE or both OE and CE will operate toggle bit. 2. Beginning and ending state of I/O6 may vary. 3. Any address location may be used but the address should not vary. 11 0291N-FLASH-07/02 Software Product Identification Entry(1) LOAD DATA AA TO ADDRESS 5555 Boot Block Lockout Feature Enable Algorithm(1) LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 90 TO ADDRESS 5555 PAUSE 10 mS LOAD DATA 80 TO ADDRESS 5555 ENTER PRODUCT IDENTIFICATION MODE(2)(3)(5) LOAD DATA AA TO ADDRESS 5555 Software Product Identification Exit(1) LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 40 TO ADDRESS 5555 LOAD DATA F0 TO ADDRESS 5555 PAUSE 10 mS EXIT PRODUCT IDENTIFICATION MODE(4) Notes: Notes: 12 1. Data Format: I/O15 - I/O0 (Hex); Address Format: A14 - A0 (Hex). 2. A1 - A17 = VIL. Manufacturer Code is read for A0 = VIL; Device Code is read for A0 = VIH. 3. The device does not remain in identification mode if powered down. 4. The device returns to standard operation mode. 5. Manufacturer Code is 1F. The Device Code is DA. LOAD DATA 00 TO ADDRESS 00000H(2) LOAD DATA FF TO ADDRESS 3FFFFH(3) PAUSE 20 mS PAUSE 20 mS 1. Data Format: I/O7 - I/O0 (Hex); Address Format: A14 - A0 (Hex). 2. Lockout feature set on lower address boot block. 3. Lockout feature set on higher address boot block. AT29C020 0291N-FLASH-07/02 AT29C020 Ordering Information ICC (mA) tACC (ns) Active Standby Ordering Code Package 70 40 0.1 AT29C020-70JC AT29C020-70PC AT29C020-70TC 32J 32P6 32T Commercial (0 to 70C) 40 0.1 AT29C020-70JI AT29C020-70PI AT29C020-70TI 32J 32P6 32T Industrial (-40 to 85C) 40 0.1 AT29C020-90JC AT29C020-90PC AT29C020-90TC 32J 32P6 32T Commercial (0 to 70C) 40 0.1 AT29C020-90JI AT29C020-90PI AT29C020-90TI 32J 32P6 32T Industrial (-40 to 85C) 40 0.1 AT29C020-10JC AT29C020-10PC AT29C020-10TC 32J 32P6 32T Commercial (0 to 70C) 40 0.3 AT29C020-10JI AT29C020-10PI AT29C020-10TI 32J 32P6 32T Industrial (-40 to 85C) 40 0.1 AT29C020-12JC AT29C020-12PC AT29C020-12TC 32J 32P6 32T Commercial (0 to 70C) 40 0.3 AT29C020-12JI AT29C020-12PI AT29C020-12TI 32J 32P6 32T Industrial (-40 to 85C) 40 0.1 AT29C020-15JC AT29C020-15PC AT29C020-15TC 32J 32P6 32T Commercial (0 to 70C) 40 0.3 AT29C020-15JI AT29C020-15PI AT29C020-15TI 32J 32P6 32T Industrial (-40 to 85C) 90 100 120 150 Note: Operation Range Not recommended for New Designs. Package Type 32J 32-lead, Plastic J-leaded Chip Carrier (PLCC) 32P6 32-pin, 0.600" Wide, Plastic Dual Inline Package (PDIP) 32T 32-lead, Thin Small Outline Package (TSOP) 13 0291N-FLASH-07/02 Packaging Information 32J - PLCC 1.14(0.045) X 45 PIN NO. 1 IDENTIFIER 1.14(0.045) X 45 0.318(0.0125) 0.191(0.0075) E1 E2 B1 E B e A2 D1 A1 D A 0.51(0.020)MAX 45 MAX (3X) COMMON DIMENSIONS (Unit of Measure = mm) D2 Notes: 1. This package conforms to JEDEC reference MS-016, Variation AE. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. SYMBOL MIN NOM MAX A 3.175 - 3.556 A1 1.524 - 2.413 A2 0.381 - - D 12.319 - 12.573 D1 11.354 - 11.506 D2 9.906 - 10.922 E 14.859 - 15.113 E1 13.894 - 14.046 E2 12.471 - 13.487 B 0.660 - 0.813 B1 0.330 - 0.533 e NOTE Note 2 Note 2 1.270 TYP 10/04/01 R 14 2325 Orchard Parkway San Jose, CA 95131 TITLE 32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC) DRAWING NO. REV. 32J B AT29C020 0291N-FLASH-07/02 AT29C020 32P6 - PDIP D PIN 1 E1 A SEATING PLANE A1 L B B1 e E 0 ~ 15 C COMMON DIMENSIONS (Unit of Measure = mm) REF SYMBOL eB Note: 1. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). MIN NOM MAX A - - 4.826 A1 0.381 - - D 41.783 - 42.291 E 15.240 - 15.875 E1 13.462 - 13.970 B 0.356 - 0.559 B1 1.041 - 1.651 L 3.048 - 3.556 C 0.203 - 0.381 eB 15.494 - 17.526 e NOTE Note 1 Note 1 2.540 TYP 09/28/01 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 32P6, 32-lead (0.600"/15.24 mm Wide) Plastic Dual Inline Package (PDIP) DRAWING NO. 32P6 REV. B 15 0291N-FLASH-07/02 32T - TSOP PIN 1 0 ~ 8 c Pin 1 Identifier D1 D L b e L1 A2 E A GAGE PLANE SEATING PLANE COMMON DIMENSIONS (Unit of Measure = mm) A1 MIN NOM MAX A - - 1.20 A1 0.05 - 0.15 A2 0.95 1.00 1.05 D 19.80 20.00 20.20 D1 18.30 18.40 18.50 Note 2 E 7.90 8.00 8.10 Note 2 L 0.50 0.60 0.70 SYMBOL Notes: 1. This package conforms to JEDEC reference MO-142, Variation BD. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion on E is 0.15 mm per side and on D1 is 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. L1 0.25 BASIC b 0.17 0.22 0.27 c 0.10 - 0.21 e NOTE 0.50 BASIC 10/18/01 R 16 2325 Orchard Parkway San Jose, CA 95131 TITLE 32T, 32-lead (8 x 20 mm Package) Plastic Thin Small Outline Package, Type I (TSOP) DRAWING NO. REV. 32T B AT29C020 0291N-FLASH-07/02 Atmel Headquarters Atmel Operations Corporate Headquarters Memory 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 487-2600 Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany TEL (49) 71-31-67-0 FAX (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France TEL (33) 2-40-18-18-18 FAX (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France TEL (33) 4-76-58-30-00 FAX (33) 4-76-58-34-80 Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4-42-53-60-00 FAX (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland TEL (44) 1355-803-000 FAX (44) 1355-242-743 e-mail literature@atmel.com Web Site http://www.atmel.com (c) Atmel Corporation 2002. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Atmel's Terms and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel's products are not authorized for use as critical components in life support devices or systems. ATMEL (R) is the registered trademark of Atmel. Other terms and product names may be the trademarks of others. Printed on recycled paper. 0291N-FLASH-07/02 /xM