Place and Play Bluetooth® Low Energy Module
New PAN1740 Series
Panasonic New Product Introduction
Revolutionizing Bluetooth Low Energy with a 5mA Current Consumption in Tx or Rx!
A revolution is underway in Bluetooth Low Energy to dramatically shrink power budgets for battery powered applications.
Panasonic’s “nanopower” family of 2nd generation BLE modules reduces transmit and receive current consumption by
more than 66% when compared to the current generation of BLE devices and nearly a 90% reduction from Bluetooth
Classic devices. Most significant is that these current reductions have been achieved without range reduction, without
Tx power reduction and without changes to the Bluetooth specification.
The PAN1740 Series is Panasonic’s next generation “nanopower” Bluetooth Low Energy module with reduced form factor,
significantly lower power consumption, embedded BLE stack and profile. Panasonic cost engineering lowers component
count and the application BOM. This single mode Bluetooth system-on-chip module is optimized for low power and small size.
The power consumption of only 5mA in Tx or Rx mode allows for the use of coin cell batteries and reduces battery requirements
up to 50% when compared to current generation BLE devices . With a fully shielded case, integrated crystal oscillators and
chip antenna, the 9.0 x 9.5 x 1.8 mm footprint of the PAN1740 Series makes it one of the smallest BLE modules available.
The PAN1740 Series is qualified to the Bluetooth 4.0 standard – FCC, IC, CE certifications are pending. Panasonic’s designer
friendly Easy-to-Use (ETU) development kits reduce design efforts and critical time to market.
• Bluetooth Smart® Module
• Tx Current @ 0dBm: 5mA
• Small Footprint: 9 x 9.5 x 1.8mm
• High Sensitivity: -93dbm typ.
• Output Power Up to 0dbm
• Embedded BLE Stack and GATT Profile
• Industrial Temperature Range: -40 to 85oC
• Two Internal Crystal Oscillators
• Integrated Antenna
• Consumer Electronics
• Wireless Sensors
• Cable Replacement
• Instrumentation
• Heart Rate Monitors
• Blood Glucose Meters
Website: us.panasonic.com/industrial
industrial@us.panasonic.com
1-800-344-2112
Copyright © 2014 Panasonic Corporation of North America.
All Rights Reserved. Specifications are subject to change without notice.
PAN1740 Series NPI, FY13-134-XXX
Features Applications
RoHS
COMPLIANT
Parameter Value Condition
Receiver Sensitivity -93 dBm typ. Ideal Signal
Output Power +0 dBm typ. @ 50 Ohm Antenna Pin
Power Supply 2.35 to 3.3 V Single Voltage Operation
Transmit 4.9 mA GFSK
Receive 4.9 mA GFSK
Operating Temperature -40 to +85°C
Technical Characteristics
REACH
COMPLIANT
DC/DC
Dialog
DA14580
Crystal
16 MHz
VSUPPLY
Full Port Multiplexer
UART SPI USB 12C
GP-ADC
Crystal
32.768 kHz
Quad-Decoder
Wakeup Timer
Block Diagram (PAN1740)
Part Number Description
ENW-89846A1KF PAN1740 Bluetooth Low Energy Module, Integrated Antenna
EVAL_PAN1740 PAN1740 Evaluation Kit, Two USB Development Modules
Ordering Information
Website: www.panasonic.com/industrial
industrial@us.panasonic.com
1-800-344-2112
Copyright © 2014 Panasonic Corporation of North America.
All Rights Reserved. Specifications are subject to change without notice.
PAN1740 Series NPI, FY13-134-XXX
For more information on the PAN1740 Bluetooth Low Energy Module, visit our blog by clicking on the link below. There, you
can download our new whitepaper, entitled “Moving Forward With Bluetooth Low Energy”.
http://www.pidtechinsights.com/2014/03/11/moving-forward-with-bluetooth-low-energy/
Additional Information
