EVAL-AD5344DBZ User Guide
UG-985
One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluating the AD5344 12-Bit, Quad-Channel Voltage Output Digital-to-Analog
Converter (DAC)
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS. Rev. A | Page 1 of 12
FEATURES
Full featured evaluation board (EVAL-AD5344DBZ)
in conjunction with nanoDAC motherboard
(EVAL-MBnanoDAC-SDZ)
On-board references
Various link options
PC control in conjunction with Analog Devices, Inc., system
demonstration platform (SDP)
EVALUATION KIT CONTENTS
EVAL-AD5344DBZ evaluation board
EVAL-MBnanoDAC-SDZ motherboard
USB cable
SOFTWARE REQUIRED
EVAL-AD5344DBZ evaluation software
HARDWARE REQUIRED
EVAL-SDP-CB1Z controller board (SDP-B controller board),
must be purchased separately
GENERAL DESCRIPTION
This user guide details the operation of the EVA L -AD5344DBZ
for the AD5344 quad-channel, voltage output DAC. The
AD5344 operates from a single 2.5 V to 5.5 V supply.
The E VA L-AD5344DBZ is designed to quickly prototype AD5344
circuits and reduce design time. The E VA L-AD5344DBZ
interfaces with the USB port of a PC via the SDP-B controller
board. Software can be downloaded via the E VA L-AD5344DBZ
product page that allows users to program the AD5344.
The E VA L-AD5344DBZ evaluation board requires the SDP-B
controller board, which is available for order on the Analog
Devices website.
Full specifications for the AD5344 are listed in the AD5344 data
sheet available from Analog Devices and should be consulted in
conjunction with this user guide when using the evaluation board.
PHOTOGRAPH OF THE EVAL-AD5344DBZ, EVAL-MBnanoDAC-SDZ, AND EVAL-SDP-CB1Z
14520-001
Figure 1.
UG-985 EVAL-AD5344DBZ User Guide
Rev. A | Page 2 of 12
TABLE OF CONTENTS
Features .............................................................................................. 1
Evaluation Kit Contents .................................................................. 1
Software Required ............................................................................ 1
Hardware Required .......................................................................... 1
General Description ......................................................................... 1
Photograph of the EVAL-AD5344DBZ, EVAL-MBnanoDAC-
SDZ, and E VA L -SDP-CB1Z ............................................................. 1
Revision History ............................................................................... 2
Evaluation Board Hardware ............................................................ 3
Power Supplies .............................................................................. 3
Link Options ................................................................................. 3
Daughter Board Link Options .....................................................3
Evaluation Board Software Quick Start Procedures .....................4
Installing the EVAL-AD5344DBZ Evaluation Software .............4
Running the Software ...................................................................4
Software Operation .......................................................................5
Evaluation Board Schematics and Artwork ...................................6
E VA L-MBnanoDAC-SDZ Motherboard ...................................6
E VA L-AD5344DBZ Daughter Board .........................................9
Ordering Information .................................................................... 11
Bill of Materials ........................................................................... 11
REVISION HISTORY
10/2017—Rev. 0 to Rev. A
Changes to Table 6 .......................................................................... 12
3/2017—Revision 0: Initial Version
EVAL-AD5344DBZ User Guide UG-985
Rev. A | Page 3 of 12
EVALUATION BOARD HARDWARE
POWER SUPPLIES
The nanoDAC® E VA L -MBnanoDAC-SDZ motherboard
supports single and dual power supplies.
The E VA L -AD5344DBZ evaluation board can be powered from
either the SDP-B port or externally by the J5 and J6 connectors,
described in Table 1.
Both AGND and DGND inputs are provided on the evaluation
board. The AGND and DGND planes are connected at one
location on the E VA L -MBnanoDAC-SDZ. It is recommended
that AGND and DGND do not connect elsewhere in the system
to avoid ground loop problems.
All supplies are decoupled to ground with 10 µF tantalum
capacitors and 0.1 µF ceramic capacitors.
Table 1. Power Supply Connectors
Connector Label Voltage
J5, Pin 1 (J5-1) VDD Analog positive power supply, VDD;
5.5 V single and dual supply
J5, Pin 2 (J5-2)
AGND
Analog ground
J5, Pin 3 (J5-3) VSS Analog negative power supply, VSS;
−5.5 V dual supply
J6, Pin 1 (J6-1) VLOGIC Digital supply from 1.8 V to VDD;
J6, Pin 2 (J6-2) DGND Digital ground
LINK OPTIONS
A number of link options are incorporated in the EVA L -
MBnanoDAC-SDZ and must be set for the required operating
conditions before using the evaluation board. Table 2 describes
the positions of the links that control the evaluation board via
the SDP-B controller board using a PC and external power
supplies. The positions listed in Table 2 through Table 4 match
the evaluation board imprints, see Figure 10.
Table 2. Link Options Setup for SDP Control (Default)
Link Number Position
REF1 2.5 V
REF2 2.5 V
REF3 2.5 V
REF4
2.5 V
LK5
C
LK6 +3V3
LK7 B
DAUGHTER BOARD LINK OPTIONS
The E VA L -AD5344DBZ daughter board has two link options.
The links control the settings of the output voltage channel. The
functions of these link options are described in detail in Table 3.
Table 4 shows how the links are configured.
Table 3. Channel Settings
Channel LK1 LK2
A A A
B A B
C B A
D B B
Table 4. Link Functions
Link Number Position
REF1 to REF4 These links select the reference source.
Position EXT selects an off board voltage reference via the appropriate EXT_REF connector.
Position VDD selects V
DD
as the reference source.
Position 4.096V selects the on-board 4.096 V reference as the reference source.
Position 2.5V selects the on-board 2.5 V reference as the reference source.
Position 5V selects the on-board 5 V reference as the reference source.
LK5 This link selects the positive DAC analog voltage source.
Position A selects the internal voltage source from the SDP-B controller board.
Position B selects the internal voltage source 3.3 V from the ADP121 on the motherboard.
Position C selects an external supply voltage, VDD.
LK6 This link selects the VLOGIC voltage source.
Position +3V3 selects the digital voltage source from the SDP-B controller board (+3V3).
Position VLOGIC selects an external digital supply voltage, VLOGIC.
LK7 This link selects the negative DAC analog voltage source.
Position A selects VSS.
Position B selects AGND.
UG-985 EVAL-AD5344DBZ User Guide
Rev. A | Page 4 of 12
EVALUATION BOARD SOFTWARE QUICK START PROCEDURES
INSTALLING THE EVAL-AD5344DBZ EVALUATION
SOFTWARE
The E VA L -AD5344DBZ evaluation software is compatible with
Windows® Vista (64-bit/32-bit) and Windows 7 (64-bit/32-bit).
Install the software before connecting the SDP-B controller
board to the USB port of the PC to ensure the PC recognizes
the SDP-B controller board when it connects to the PC.
To install the E VA L -AD5344DBZ evaluation software, take the
following steps:
1. Start the Windows operating system.
2. Download the installation software from the E VA L -
AD5344DBZ evaluation board page.
3. Run the setup.exe file from the installer file if it does not
open automatically.
4. After the installation is complete, power up the evaluation
board as described in the Power Supplies section.
5. Connect the E VA L -AD5344DBZ to the SDP-B controller
board and the SDP-B controller board to the PC using the
USB cable included in the evaluation kit.
6. When the software detects the EVA L -AD5344DBZ,
proceed through any dialog boxes that appear to finalize
the installation.
RUNNING THE SOFTWARE
To run the E VA L -AD5344DBZ evaluation software, proceed
with the following steps:
1. Connect the E VA L -AD5344DBZ to the SDP-B controller
board and connect the USB cable from the SDP-B
controller board to the PC.
2. Power up the evaluation board as described in the Power
Supplies section.
3. Click Start > All Programs > Analog Devices > AD5344
Evaluation Software to locate the evaluation board.
If the SDP-B controller board does not connect to the USB port
when the software launches, a connectivity error displays (see
Figure 2).
Connect the SDP-B controller board to the USB port of the PC
and wait a few seconds. Once the SDP-B controller board and
the E VA L -AD5344DBZ daughter board are detected, the
display updates (see Figure 3).
14520-002
Figure 2. Connectivity Error
14520-003
Figure 3. Hardware Select
Alternatively, the EVA L -AD5344DBZ evaluation software can be
used without an evaluation board. The E VA L-AD5344DBZ
evaluation software runs in simulation mode displaying
expected outputs based on the input data. The main window of
the E VA L -AD5344DBZ evaluation software then opens, shown
in Figure 4.
EVAL-AD5344DBZ User Guide UG-985
Rev. A | Page 5 of 12
14520-004
Figure 4. AD5344 Evaluation Board Software Main Window
SOFTWARE OPERATION
The E VA L -AD5344DBZ evaluation software allows the user to
program values to the input and DAC registers of each DAC
individually (see Figure 4). Ensure the LK1 position and LK2
position on the daughter board match the DAC selected on the
DAC Selection pane on the GUI.
Write to DAC Register
Select the Write to DAC Register button to load the code of the
input data control to the DAC register of the DAC. Ensure LK1
and LK2 are set up correctly.
LDAC Control
Select the Pulse LDAC button to bring the LDAC pin low and
then high, copying the data from the input registers to the DAC
registers, and updating the outputs accordingly.
Alternatively, set the LDAC pin high or low by clicking the blue
progressive disclosure button on the INTERFACE LOGIC
block. A window opens that allows the user to click the
appropriate LDAC setting, shown in Figure 4.
14520-005
Figure 5. LDAC Control
Power-Down Control
All of the DACs can be powered down simultaneously. Click on the
blue progressive disclosure buttons to access the POWER-DOWN
LOGIC block. When the power-down setting for the DAC is
selected, click the OK button to write the appropriate values to the
AD5344.
UG-985 EVAL-AD5344DBZ User Guide
Rev. A | Page 6 of 12
EVALUATION BOARD SCHEMATICS AND ARTWORK
EVAL-MBnanoDAC-SDZ MOTHERBOARD
EXT_VDD
VLOGIC
GND
EXT_VSS
CONNECTOR
STANDARD
SDP
PARALLEL
PORT
SPORT
SPI
I2C
GENERAL
INPUT/OUTPUT
TIMERS
*NC ON BLACKFIN SDP 120
NC
119
NC
118
GND
117
GND
116
VIO(+3.3V)
115
GND
114
*PAR_D22
113
*PAR_D20
112
*PAR_D18
111
*PAR_D16
110
PAR_D15
109
GND
108
PAR_D12
107
PAR_D10
106
PAR_D8
105
PAR_D6
104
GND
103
PAR_D4
102
PAR_D2
101
PAR_D0
100
99
98
GND
97
PAR_A2
96
PAR_A0
95
PAR_FS2
94
PAR_CLK
93
GND
92
SPORT_RSCLK
91
SPORT_DR0
90
SPORT_RFS
89
SPORT_TFS
88
SPORT_DT0
87
SPORT_TSCLK
86
GND
85
SPI_SEL_A
84
SPI_MOSI
83
SPI_MISO
82
SPI_CLK
81
GND
80
SDA_0
79
SCL_0
78
GPIO1
77
GPIO3
76
GPIO5
75
GND
74
GPIO7
73
TMR_B
72
TMR_D
71
CLK_OUT
70
NC
69
GND
68
NC
67
NC
66
NC
65
WAKE
64
SLEEP
63
GND
62
UART_TX
61
BMODE1
60 RESET_IN
59 UART_RX
58 GND
57 RESET_OUT
56 EEPROM_A0
55 NC
54 NC
53 NC
52 GND
51 NC
50 NC
49 TMR_C*
48 TMR_A
47 GPIO6
46 GND
45 GPIO4
44 GPIO2
43 GPIO0
42 SCL_1
41 SDA_1
40 GND
39 SPI_SEL1/SPI_SS
38 SPI_SEL_C
37 SPI_SEL_B
36 GND
35 SPORT_IN T
34 SPI_D3*
33 SPI_D2*
32 SPORT_DT1
31 SPORT_DR1
30 SPORT1_TDV*
29 SPORT0_TDV*
28 GND
27 PAR_FS1
26 PAR_FS3
25 PAR_A1
24 PAR_A3
23 GND
22 PAR_CS
21 PAR_RD
20 PAR_D1
19 PAR_D3
18 PAR_D5
17 GND
16 PAR_D7
15 PAR_D9
14 PAR_D11
13 PAR_D13
12 PAR_D14
11 GND
10 PAR_D17*
9PAR_D19*
8PAR_D21*
7PAR_D23*
6GND
5USB_VBUS
4GND
3GND
2NC
1VIN
J10
1A0
2A1
3A2
4VSS
8
VCC 7
WP 6
SCL 5
SDA
U3
24LC32
R2
100kΩ
R4
DNP
R3
100kΩ
DGND AGND
L1
BEAD
R1
1.6Ω
+
C11
4.7µF
C10
0.1µF
+C7
10µF
1VIN
2GND
3EN 4
NC
5
VOUT
U2
ADP121-AUJZ33
C3
1µF
C4
1µF
C
B
A
LK5
J6-1
J6-2
C5
0.1µF
+C6
10µF
A
B
LK6
J5-1
J5-2
J5-3
C2
0.1µF
+
C1
10µF
A
B
LK7
R7 100Ω
R5 100Ω
R6 100Ω
R8 100Ω
R9 100Ω
R10 100Ω
R11 100Ω
R12 100Ω
R13 100Ω
R14
14520-006
100Ω
C8
0.1µF
+
C9
10µF
R15
100Ω
R16
DNP
PD
SCL
SDA
CS
WR
DB0
DB2
DB4
DB6
DB8
DB10
DB1
DB3
DB5
DB7
DB9
DB11
+3.3V
+3.3V
DGND
+5V
USB_VBUS
USB_VBUS
+3.3V
VDD
+3.3V
DGND
VLOGIC
DGND
+3.3V
DGNDDGND
VSS
+5V
CLR
LDAC
SCLK
SDO
SDIN
SYNC
EXT_VDD
EXT_VDD
+5V
DGND
DGND
DGND
DGND
DGND DGND
Figure 6. EVAL-MBnanoDAC-SDZ Motherboard, SDP-B Controller Board Connector, and Power Supply
+2.5V +4.096V
C16
1µF
C15
1µF
6
OUTPUT
2VS
3SLEEP
4
GND
U6
REF198
C17
1µF
+5V
+2.5V +4.096V
EX_REF_1 EX_REF_2 EX_REF_3 EX_REF_4
VREF_1 VREF_2 VREF_3 VREF_4
2VIN
5TRIM
6
VOUT
4
GND
U4
ADR445ARMZ
2VIN
4
GND
5
TRIM
7COMP
6
VOUT
U5
ADR431BRZ
D
C
A
B
E
REF3
D
C
A
B
E
REF4
D
C
A
B
E
REF1
D
C
A
B
E
REF2
+5VREF+2_5VREF +4_096VREF
VDD VDD
+5VREF
+2_5VREF
+4_096VREF
VREF1
+5VREF
+2_5VREF
+4_096VREF
VREF2
+5VREF
+2_5VREF
+4_096VREF
VREF3
+5VREF
+2_5VREF
+4_096VREF
VREF4
VDD VDD VDD VDD
VDD
14520-007
Figure 7. EVAL-MBnanoDAC-SDZ Motherboard Reference Voltage Selector Circuit
EVAL-AD5344DBZ User Guide UG-985
Rev. A | Page 7 of 12
DAUGHTER BOARD CONNECTOR
SPI PMOD CONNNECTOR GPIO PMOD CONNNECTOR
I2C PMOD CONNNECTOR
1
3
5
7
9
2
4
6
8
10
J2
1 2
3 4
5 6
7 8
910
11 12
13 14
15 16
J1
SDIN SDO SCLK SYNC SCL LDAC CLR PD GAIN SDA
1 2
3 4
5 6
7 8
J9
J8-1
J8-2
J8-3
J8-4
J8-5
J8-6
J7-1
J7-2
J7-3
J7-4
J7-5
J7-6
J3-1
J3-2
J3-3
J3-4
J3-5
J3-6
J4-1
J4-2
J4-3
J4-4
J4-5
J4-6
J4-7
J4-8
VDD
VREF1
VREF2
VREF3
VREF4
VLOGIC
SDASCL
SYNC
SCLK
SDO
SDIN LDAC
CLR
PD
GAIN
DB6
DB7
DB8
DB9
DB0
DB1
DB2
DB3
VOUT_0
VOUT_1
VOUT_2
VOUT_3
VOUT_4
VOUT_5
VOUT_6
VOUT_7
SCL
SDA
DGND
VLOGIC
SCL
SDA
DGND
VLOGIC
SYNC
SDO
SDIN
SCLK
DGND
VLOGIC
PD
GAIN
DGND
LDAC
CLR
VLOGIC
DGND
CS WR
DB11
DB5
DB10
DB4
AGND
14520-008
Figure 8. EVAL-MBnanoDAC-SDZ Motherboard Connectors to Daughter Board and Serial Interface
VOUT_0
VOUT_1
VOUT_2
VOUT_3
VOUT_4
VOUT_5
VOUT_6
VOUT_7
+
-
3
2
1
U10-A
AD8608ARUZ
+
–
5
6
7
U10-B
AD8608ARUZ
+
–
10
9
8
U10-C
AD8608ARUZ
+
–
12
13
14
U10-D
AD8608ARUZ
3+
2–
1
U7-A
AD8616ARZ
5+
6–
7
U7-B
AD8616ARZ
8
V+
4
V–
U7-C
AD8616ARZ
2–
3+
6
OP
4
V–
7
V+
U11
AD8655
2–
3+
6
OP
4
V–
7
V+
U12
AD8655
VOUT_0
VOUT_1
VOUT_2
VOUT_3
VOUT_4
VOUT_5
VOUT_6
VOUT_7
VDD
VSS
VDD
VDD
VSS
VSS
14520-009
Figure 9. EVAL-MBnanoDAC-SDZ Motherboard Output Amplifier Circuit
EVAL-AD5344DBZ User Guide UG-985
Rev. A | Page 11 of 12
ORDERING INFORMATION
BILL OF MATERIALS
Table 5. EVAL-MBnanoDAC-SDZ Motherboard
Reference Designator Description Supplier1/Part Number
C1, C6, C7, C9 6.3 V tantalum capacitors (Case A), 10 µF, ±20% FEC 1190107
C2, C5, C8, C10, C15 to C17 50V, X7R ceramic capacitors, 0.1 µF, ±10% FEC 1759122
C3, C4 10 V, X5R ceramic capacitors, 1 uF, ±10% GRM188R61A105KA61D2
C11 6.3 V tantalum capacitor (Case A), 4.7 µF, ±20% FEC 1432350
EXT_REF_1 to EXT_REF_4 Straight PCB mount SMB jacks, 50 Ω FEC 1206013
J1 Header, 2.54 mm, 2 × 8-way FEC 2308428
J2 Header, 2.54 mm, 2 × 5-way FEC 9689583
J3, J7, J8 Headers, 2.54 mm, 1 × 6-way FEC 9689508
J4
Header, 2.54 mm, 1 × 8-way
FEC 1766172
J5 3-pin terminal block FEC 1667472
J6 2-pin terminal block FEC 151789
J9 Header, 2.54 mm, 2 x 4-way FEC 1667509
J10 120-way connector FEC 1324660
L1 Inductor, SMD, 600 Ω FEC 9526862
LK5 6-pin (3 × 2-way) 0.1" header and shorting block FEC 148-535 and FEC 150-411 (36-pin strip)
LK6, LK7 4-pin (2 × 2-way) 0.1" header and shorting blocks FEC 148-535 and FEC 150-411 (36-pin strip)
REF1 to REF4 10-pin (5 × 2-way) 0.1" header and shorting blocks FEC 1022227 and FEC 150-411
R1 Resistor, surge, 1.6 Ω, 1%, 0603 FEC 1627674
R2, R3 SMD resistors, 100 kΩ, 1%, 0603 FEC 9330402
R5 to R15 SMD resistors, 100 Ω, 1%, 0603 FEC 9330364
U2
3.3 V linear regulator
ADP121-AUJZ33R7
U3 32 kΩ I2C Serial EEPROM FEC 1331330
U4 5 V Reference MSOP ADR445ARMZ
U5 Ultralow noise XFET® voltage reference ADR431BRZ
U6 4.096 V reference REF198ESZ
U7 Dual op amp AD8616ARZ
U10 Quad op amp AD8608ARMZ-R7
U11, U12 Op amp AD8655ARMZ
1 FEC refers to Farnell Electronic Component Distributors.
2 GRM refers to Murata Manufacturing Company.
UG-985 EVAL-AD5344DBZ User Guide
Rev. A | Page 12 of 12
Table 6. EVAL-AD5344DBZ Daughter Board
Reference Designator Description Supplier1/Part Number
A Red test point, do not insert Not applicable
B Red test point, do not insert Not applicable
C Red test point, do not insert Not applicable
C1 Not inserted Not applicable
C2 Not inserted Not applicable
C3 Not inserted Not applicable
C4 Not inserted Not applicable
C5 50 V X7R ceramic capacitor FEC 1759122
C6 6.3 V tantalum capacitor (Case A) FEC 1190107
D Red test point, do not insert Not applicable
J1 16-pin (2 × 8-way) header, inserted from solder side FEC 2308428
J2 10-pin (2 × 5-way) straight header, 2.54 mm pitch, inserted from solder side FEC 9689583
J3 6-pin (1 × 6-way) straight header, 2.54 mm pitch, inserted from solder side FEC 9689508
J4 Header, 2.54 mm, PCB, 1 × 8-way, inserted from solder side FEC 1766172
J5 Jumper block using a 3-pin SIP header FEC 1022248 and FEC 150410
J6 Jumper block using a 3-pin SIP header FEC 1022248 and FEC 150410
R1 Not inserted Not applicable
R2 Not inserted Not applicable
R3 Not inserted Not applicable
R4 Not inserted Not applicable
U1 Quad 12-bit DAC AD5344BRUZ
1 FEC refers to Farnell Electronic Component Distributors.
I2C refers to a communication protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2017 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG14520-0-10/17(A)
