DOCUMENT NUMBER NCD-62B2-02
SSCF-2P1 Series
SC DUPLEX HOUSING
(φ0.9mm / Push-pull Type)
TECHNICAL SPECIFICATIONS
Seiko Instruments Inc.
Components Sales Dept.
8, Nakase 1-Chome
Mihama-ku, Chiba-shi, Chiba-ken
261 JAPA N
Telephone : 043-211-1214
-1215
Facsimile : 043-211-8035
SSCF-2P1 Series SC DUPLEX HOUSING ( φ0.9mm / Push-pull Type )
TECHNICAL SPECIFICATIONS
Document Number NCD-62B2-02
NCD-62B2-01 February 1996
NCD-62B2-02 March 1996
Copyright 1996 by Seiko Instruments Inc.
All right reserved.
The information contained herein shall not reproduced or disclosed to any third party
without the express written consent of SII.
The Specifications contained herein are subject to change without notice.
SIIis a trademark of Seiko Instruments Inc.
Please address any questions, comments, and suggestions to:
Seiko Instruments USA Inc.
Electronics Components Division
2990 West Lomita Boulevard
Torrance, CA 90505, U.S.A.
Phone: 310-517-7780
Fax: 310-517-7792
Seiko Instruments GmbH
OFC Division
Siemensstraße 9b
D-63263 Neu-Isenburg, Germany
Phone: 06102-297-0
Fax: 06102-297-211
Seiko Instruments (H.K.) Ltd.
Sales Department
4th & 5th Floor, Wyler Center 2
200 Tai Lin Pai Road, Kwai Chung
N.T., Kowloon, Hong Kong
Phone: 852-2421-8611
Fax: 852-2480-5479
Seiko Instruments Taiwan Inc.
Sales Department
5F-1, No.99, Sec. 2, Chung Shan
Rd.
Taipei 104, Taiwan, R.O.C.
Phone: 02-563-5001, 523-5111
Fax: 02-521-9519
Seiko Instruments Singapore pte. Ltd.
2, Marsiling Lane,
Woodlands New Town,
Singapore, 2573, Singapore
Phone: 65-2691370
Fax: 65-2699729
ii
TABLE OF CONTENTS
Section Page
1. PROVISION 1
1.1 Application Limit 1
2. PARTS NUMBER 1
3. GENERAL SPECIFICATIONS 2
3.1 Parts and Materials 2
3.2 Physical Dimensions 2
3.3 General Tolerances 2
4. PACKING 3
Table
Table 1 Parts Number 1
Table 2 Parts and Materials 2
Table 3 General Tolerance 2
Figure
Figure 1 SSCF-2P1 Housing 4
Figure 2 to 7 Part Dimensions 5 to 7
iii
iv
1
1. PROVISION
1.1 Application Limit
These specifications apply to the SSCF-2P1 SC DUPLEX HOUSING ( φ0.9mm / Push-
pull Type ) supplied by SII.
2 . PARTS NUMBER
Parts Number of the Housing is Shown in Table 1.
Table 1 Parts Number
2
3. GENERAL SPECIFICATIONS
3.1 Parts and Materials
Parts and the Materials are shown in Table 2.
Table 2 Parts and Materials
No. Part Name Q'ty Material Notes
①Grip 1 Plastics Blue , UL94 V-0
②Plug frame 2 Plastics White , UL94 V-0
➂Spring 2 Stainless Steel - -
➃Stop ring 2 Brass Nickel Plating
⑤Hood 2 Synthetic Rubber Hood Color Shows Table 1, UL94 V-0.
➅Cap 2 PVC Blue
3.2 Physical Dimensions
Figure 1 shows the assembled state of SSCF-2P1.
Figure 2 to 7 show the part dimension.
•Compatible with NTT SCF-2PH plug housing
3.3 General Tolerances
Permissible deviation in dimensions without tolerance indication is in accordance with JIS
B 0405 class m, as shown in Table 3.
Table 3 General Tolerance (JIS B 0405 class m)
Basic size step (mm)
Over Under Permissible deviation (mm)
0.5 3
36
630
30 120
±0.1
±0.1
±0.2
±0.3
3
4 . PACKING
The product is packed to prevent damage during shipping.
4
note.1: This drawing Shows the Tentatively assembled condition. In practice, the housing
is not assembled like this.
note.2: This drawing does not include Caps. Unit: mm
Figure 1 SSCF-2P1 HOUSING
5
Unit: mm
Figure 2 ①Grip
Unit: mm
Figure 3 ②Plug frame
6
Unit: mm
Figure 4 ➂Spring
Unit: mm
Figure 5 ➃Stop ring
7
Unit: mm
Figure 6 ⑤Hood
Unit: mm
Figure 7 ➅Cap
