711 Series Sin
g
le Wa
y
DB-1a
Data Bus In terconnecti on System
Data Bus Interconnection S
y
stem desi
g
ned for data
transmission as defined by MIL-STD-1553B,
STANAG 3838 and DEF STAN 00-18 (Part 2).
This system is also ideal for video transmission systems and
the termination of screened twisted pairs.
BS 9522 F0043 approved and qualified to
PAN 6484/6499. 711 series connectors incorporate
an anti-vibration locking mechanism. The triaxial, all
crimp contact used in the 711 series single way
connectors is common to the multi-way connector
housin
g
allowin
g
u
p
ratin
g
of e
q
ui
p
ment at an
y
time.
Plu
g
s
Plug - 711-5000/C2832-
Receptacles
Single Hole Mtg. Receptacle -711-5001/C2834-
S
q
. Flan
g
e Mt
g
. Rece
p
tacle - 711-5002/C2835-/PAN 6484 B
Plu
g
-711-5011/C2831-/PAN 6484 F
Single Hole Mtg. Receptacle - 711-5008/C2844-
PANEL PIERCING
AS FOR 5001
PANEL PIERCING AS
FOR-5002
NOTE: This con n ec tor is only for use with discrete wir in g and is not su itable for u se with Data Bus c able.
Sq. Flange Mtg. Receptacle - 711-5009/C2838-(M3 Clinch nuts fitted)
NOTE: This con n ec tor is only for use with discrete wir in g and is not su itable for u se with Data Bus c able.
Sq. Flange Mtg. Receptacle - 711-5010/C2837-/PAN 6484C (M3 Clinch nuts fitted)
PANEL PIERCING AS
FOR - 5002
Sq. Flange Mtg. Receptacle with P.C. Termination Contacts - 711-5015/C2839
(clinch nuts fitted)
PANEL PIERCING
AS FOR-5002
Sin
g
le Hole Mt
g
. Rece
p
tacle with bulkhead seal - 711-5016/C2833-/PAN 6484
A
PANEL PIERCING
AS FOR 5002
S
q
. Flan
g
e Mt
g
. Rece
p
tacle - 711-5024/C2836-
PANEL PIERCING
AS FOR 5002
Sin
g
le Hole Mt
g
. Rece
p
tacle with bulkhead seal and P.C. Termination Contacts-711-5038-
PANEL PIERCING
AS FOR 5001
Terminators
Plug Terminator 77Ω±1 - 5013-XX/C2843-/PAN 6484 L
Note: 711 seri es terminators are only fitted with a main k ey w ay an d will suit any k ey way or ien tation.
S
q
. Flan
g
e Mt
g
. Rece
p
tac le Termin ator
(
3
K
Ω±5%
)
- 5017 - XX/C2845-/PAN 6484 M
PANEL PIERCING
AS FOR _5002
Note: 711 seri es terminators are only fitted with a main k ey w ay an d will suit any k ey way or ien tation.
In Line Rece
p
tacle Terminator
(
3
K
Ω±5%
)
- 5028 - XX/C2846-/
Note: 711 seri es terminators are only fitted with a main k ey w ay an d will suit any k ey way or ien tation.
XX Refers to the terminator impedance value. This value can
be selected according to the characteristic impedance of
the data bus transmission line or to simulate the RT
internal impedance. Amphenol standard terminators come
fitted with two impedance values.
BUS terminators = 77 ohm STUB terminators = 3K ohm
e.g. Order 711-5017-77, 711-5028-3K etc.
For special requirements contact Amphenol
Technical Support and Product Management team.
Loads
Sq. Flange Mounting 10KΩ±5% in line load - 5020 /PAN 6484 N
Orderin
g
Ordering by Amphenol
Part Numbers
Series designation 711
711 - 5000 - 1 (XXX)
Deviation Code
(462) Cadmium Olive drab plating
(473) Less clinch nuts
Orientation (1 for normal orientation)
Ke
y
s/Ke
y
wa
y
s 1
,
2
,
3
,
4 and 5
)
Shell Style
5000- Plug, with socket contact.
5001- Receptacle, sealed. Single hole mounting.
5002- Receptacl e, square flange.
5008- Single hole mounting
receptacle for discrete wiring.
5009- Receptacl e, square flange.
Low profile, clinch nuts fitted
for discrete wiring.
5010- Receptacl e, square flange.
Clinch nuts fitted.
5011- Plug to take cable accessories.
5013- Plug terminator 750.
5015- Receptacl e, square flange.
P.C. termination contacts. Clinch nuts fitted.
5016- Receptacl e, sing le hole mount with
bulkhead seal, to take cab le ac ces sori es.
5017- Receptacle terminator 3Kfl.
Square flange mounting.
5020- In line load 1 OKSZ square
flange mounting.
5024- Receptacle, square flange mount,
to take cable accessories.
5028- In line receptacle terminator3Kfl.
5038- Receptacl e, sing le hole mounting with
bulkhead seal, P.C. termination.
Orderin
g
by B.S. Part Numbers
BS9522 F0043 C2831 08 01 F10 (XXXX)
Basic number
Shell style
C2831 as per shell style 5011
C2832 as per shell style 5000
C2833 as per shell style 5016
C2834 as per shell style 5001
C2835 as per shell style 5002
C2836 as per shell style 5024
C2837 as per shell style 5010
C2838 as per shell style 5009
C2839 as per shell style 5015
C2843 as per shell style 5013
C2844 as per shell style 5008
C2845 as per shell style 5017
C2846 as per shell style 5028
C2847 as
p
er shell st
y
le 5020
Supp. load details
V
arian
t
O-Electroless nickel
1-CAD/Olive drab
2-Zinc Cobalt
Polarisation 1-Normal
orientation 2,3,4,5
Also available
0-Universal - only
ma
j
or ke
y
wa
y
fitted
Contact style
F - Female
M - Male
Housin
g
arran
g
emen
t
Orderin
g
by Pa n N umbe
r
PAN 6484
A
X
Basic number
Shell style
A as per shell style 5016
B as per shell style 5002
C as per shell style 5010
F as per shell style 5011
L as per shell style 5013
M as per shell style 5017
N as
p
er shell st
y
le 5020
Polarisation 1 -
Normal orientation
2,3,4,5 No
designation - only
major keyway fitted
Only available in
CAD/Oli ve drab
Protective Ca
p
s
Caps and Cords
711-0100-XX For use with all single way receptacles.
711-0112-XX For use with all single way plugs.
XX denotes the length of cord or chain required.
01 = 3"
02 = 3.5"
03=4"
Caps and Chains
711-0121-XX For use with all single way receptacles.
711-0122-XX For use with all single way plugs. Use deviation (462) for Cadmium Olive drab finish.
Caps and Cords
Caps and Chains
Contacts
Contacts may be ordered separately under the following Part No.'s:.
711-0013-1 - Pin contact. 711-0014-1 - Socket contact.
711-0037 -Pin contact for use with discrete wire.
Crimp Tools for 711 Series Connectors
Centre contact crimp - Crimp tool M22520/2-01.
Positioner 294GB-5027-1.
Intermediate/Outer crimp - Crimp tool 227-944 (M22520/5-01).
Die Set 294GB-5026-1.
Key/Keyway Orientations
ANGLES
POS W X Y Z
1 105 35 75 50
2 118 30 100 30
382507545
492357550
5 118 35 75 50
0*
Datum is a lways taken from major key or keyway. In
receptacles the major keyway always remains fixed in
relation to the mounting flange.
*O is a universal keyway. Only the major keyway is fitted.
Size #1 0 Data Bus Contact Assembl
y
Instructions
Slide clam
p
nut, seal and ferrule over cable.
(Nut & seal only applicable on single way
connector).
Remove outer sheath of cable to 7.5mm comb out all
braids evenly and fold back. Remove cable fillers from
stripped leng th. Strip the centre contact conductor to
4.5mm. Note: It is recommended that both
intermediate and centre contact conductors a r e
scored at the correct stripping length. The
intermediate conductor insulation should not be
removed until the centre contact has been crimped.
Crim
p
centre conta ct
(
Pin or Socket
)
on to the
stripped wire using tool M22520/2-01 and crimp
positioner 294GB-5027-1 (setting No. 4 for 24AWG)
butting rear end of contact to wire insulation. The
conductor end should be visible in the inspection
hole. Note: A second hole is p ermiss ible in the
socket conta ct for ma nufa cturing p urp oses. It is not
req u i r ed to be on the sa m e centre li ne as the
inspection hole.
Stri
p
intermediate contact conductor to 4.5mm.
Insert centre contact into ce ntre hole of intermed iate
contact conductor into the outer hole of the
intermediate contact assembly. Push firmly home
until the centre contact is felt to snap into place and
ensure that the insulation of each conductor is fully
inserted into the intermediate contact insulator. The
intermediate conductor should be visible in the
inspection hole in the intermediate contact. There
should be no loose cable strands visible. Crimp the
intermediate contact assembly using the appropriate
cavity of crimp jaw 294GB-5026-1 fitted into
M22520/5-01 tool.
Slide the ferrule forward under the braid to
trap the braid against the rear of the
intermediate contact insulator, for all
succeeding operations keep the ferrule firmly
against the rear of the insulator using
insertion tool (294GB-5028).
Comb the brai d back evenl
y
and flatten it
onto the ferrule.
Slide the outer contact bod
y
over the
intermediate contact assembly and ferrule
until approximately 1.5 mm of the ferrule is
visible. Trim off the excess braid using the
rear of the outer contact body as a guide.
Ensure that there are no loose braid clippings
at the rear of the ferrule.
Place the outer contact bod
y
into the
hexagona l cavi ty of the crimp jaws
(294GB-5026-1). Slide the intermediate
contact assembly and ferrule fully into the
outer body using the insertion tool. The rear
of the ferrule should be - 0 .5 or ± 0.5 mm to
the rear of the outer contact body when fully
inser ted. Complete the h exagonal cri mp.
