49% FPO (R) PCM1702P PCM1702U BiCMOS Advanced Sign Magnitude 20-Bit DIGITAL-TO-ANALOG CONVERTER FEATURES DESCRIPTION ULTRA LOW -96dB max THD+N (No External Adjustment Required) The PCM1702 is a precision 20-bit digital-to-analog converter with ultra-low distortion (-96dB typ with a full scale output). Incorporated into the PCM1702 is an advanced sign magnitude architecture that eliminates unwanted glitches and other nonlinearities around bipolar zero. The PCM1702 also features a very low noise (120dB typ SNR: A-weighted method) and fast settling current output (200ns typ, 1.2mA step) which is capable of 16X oversampling rates. NEAR-IDEAL LOW LEVEL OPERATION GLITCH-FREE OUTPUT 120dB SNR TYP (A-Weight Method) INDUSTRY STD SERIAL INPUT FORMAT FAST (200ns) CURRENT OUTPUT (1.2mA) Applications include very low distortion frequency synthesis and high-end consumer and professional digital audio applications. CAPABLE OF 16X OVERSAMPLING COMPLETE WITH REFERENCE LOW POWER (150mW typ) Clock Data LE DCOM ACOM +VCC -VCC Input Shift Register and Control Logic Balanced Current Segment DAC A Balanced Current Segment DAC B IOUT Reference and Servo Bipolar Offset RF DC SERV DC BPO DC International Airport Industrial Park * Mailing Address: PO Box 11400 Tel: (520) 746-1111 * Twx: 910-952-1111 * Cable: BBRCORP * * Tucson, AZ 85734 * Street Address: 6730 S. Tucson Blvd. * Tucson, AZ 85706 Telex: 066-6491 * FAX: (520) 889-1510 * Immediate Product Info: (800) 548-6132 (c) 1993 Burr-Brown Corporation PDS-1175B 1 SBAS026 Printed in U.S.A. June, 1995 PCM1702 (R) SPECIFICATIONS All specifications at 25C, VCC and +VDD = 5V unless otherwise noted. PCM1702P/U, -J, -K PARAMETER CONDITIONS RESOLUTION MIN TYP MAX 20 DYNAMIC RANGE, THD + N at -60dB Referred to Full Scale, with A-weight DIGITAL INPUT Logic Family Logic Level: VIH VIL IIH IIL Data Format Input Clock Frequency UNITS Bits 110 dB TTL/CMOS Compatible +2.4 0 +VDD 0.8 10 10 VIH = +VDD VIL = 0V Serial, MSB First, BTC(1) 12.5 20.0 V V A A MHz (2) TOTAL HARMONIC DISTORTION + N P/U VO = 0dB VO = -20dB VO = -60dB P/U, -J VO = 0dB VO = -20dB VO = -60dB P/U, -K VO = 0dB VO = -20dB VO = -60dB ACCURACY Level Linearity Gain Error Bipolar Zero Error(5) Gain Drift Bipolar Zero Drift Warm-up Time IDLE CHANNEL SNR(6) ANALOG OUTPUT Output Range Output Impedance Settling Time Glitch Energy POWER SUPPLY REQUIREMENTS Supply Voltage Range: +VCC = +VDD -VCC = -VDD Combined Supply Current: +ICC Combined Supply Current: -ICC Power Dissipation fS = 352.8kHz(3), f = 1002Hz(4) fS = 352.8kHz(3), f = 1002Hz(4) fS = 352.8kHz(3), f = 1002Hz(4) fS = 352.8kHz(3), f = 1002Hz(4) fS = 352.8kHz(3), f = 1002Hz(4) fS = 352.8kHz(3), f = 1002Hz(4) fS = 352.8kHz(3), f = 1002Hz(4) fS = 352.8kHz(3), f = 1002Hz(4) fS = 352.8kHz(3), f = 1002Hz(4) -92 -82 -46 -96 -83 -48 -100 -84 -50 At -90dB Signal Level 0.5 0.5 0.25 25 5 1 0C to 70C 0C to 70C Bipolar Zero, A-weighted Filter 110 (0.003% of FSR, 1.2mA Step) +4.75 -4.75 +VCC = +VDD = +5V -VCC = -VDD = -5V VCC = VDD = 5V TEMPERATURE RANGE Operating Storage -25 -55 -88 -74 -40 -92 -76 -42 -96 -80 -44 3 dB dB dB dB dB dB dB dB dB dB % % ppm of FSR/C ppm of FSR/C minute 120 dB 1.2 1.0 200 No Glitch Around Zero mA k ns +5.00 -5.00 +5.00 -25.00 150 +5.25 -5.25 +9.0 -41.0 250 V V mA mA mW +85 +125 C C NOTES: (1) Binary Two's Complement coding. (2) Ratio of (DistortionRMS + NoiseRMS) / SignalRMS. (3) D/A converter sample frequency (8 x 44.1kHz; 8x oversampling). (4) D/A converter output frequency (signal level). (5) Offset error at bipolar zero. (6) Measured using an OPA627 and 5k feedback and an A-weighted filter. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. (R) PCM1702 2 ABSOLUTE MAXIMUM RATINGS (DIP Package) ABSOLUTE MAXIMUM RATINGS (SOP Package) Power Supply Voltage .................................................................. 6.5VDC Input Logic Voltage ........................................... DGND--0.3V~+VDD+0.3V Operating Temperature ..................................................... -25C to +85C Storage Temperature ...................................................... -55C to +125C Power Dissipation .......................................................................... 500mW Lead Temperature (soldering, 10s) .................................................. 260C Power Supply Voltage .................................................................. 6.5VDC Input Logic Voltage ........................................... DGND--0.3V~+VDD+0.3V Operating Temperature ..................................................... -25C to +85C Storage Temperature ...................................................... -55C to +125C Power Dissipation .......................................................................... 300mW Lead Temperature (soldering, 5s) .................................................... 260C PIN ASSIGNMENTS (DIP Package) PIN ASSIGNMENTS (SOP Package) PIN MNEMONIC PIN MNEMONIC PIN MNEMONIC PIN MNEMONIC 1 2 3 4 5 6 7 8 DATA CLOCK +VDD DCOM -VDD LE NC NC 9 10 11 12 13 14 15 16 +VCC BPO DC IOUT ACOM ACOM SERV DC REF DC -VCC 1 2 3 4 5 6 7 8 9 10 DATA CLOCK NC +VDD DCOM -VDD LE NC NC NC 11 12 13 14 15 16 17 18 19 20 +VCC BPO DC NC IOUT ACOM ACOM SERV DC NC RFE DC -VCC PACKAGE INFORMATION(1) MODEL PCM1702P PCM1702U PACKAGE PACKAGE DRAWING NUMBER 16-Pin Plastic DIP 20-Pin Plastic SOP 180 248 GRADE MARKING (SOP Package) NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix D of Burr-Brown IC Data Book. MODEL PACKAGE PCM1702U PCM1702U-J PCM1702U-K Marked PCM1702. Marked with white dot by pin 10. Marked with red dot by pin 10. CONNECTION DIAGRAM 47F + 2 CLOCK 2 22F + +5V VDD DATA 1 1 15 19 LE 7 6 14 17 + 4 3 11 14 + 5 4 10 12 6 5 9 47F 47F -5V VDD -5V VCC 16 20 11 + 100F RNF VOUT 47F + +5V VCC + 47F 13 16 12 15 = SOP = DIP (R) 3 PCM1702 TYPICAL PERFORMANCE CURVES All specifications at 25C, VA and VD = 5.0V unless otherwise noted. 16-BIT LEVEL LINEARITY (Dithered Fade-to-Noise) THD+N vs FREQUENCY -40 8 Deviation from Ideal Level (dB) -60dB THD+N (dB) -60 -40dB -80 -20dB -100 0dB -120 20 100 1k 6 4 2 0 -2 -4 -6 -8 -120 10k -110 -100 Output Frequency (Hz) -90 -80 -70 -60 Output Signal Level (dB) -90dB SIGNAL SPECTRUM (100Hz Bandwidth) 16-BIT MONOTONICITY 1.5 -80 Power Spectrum (dB) Output Voltage (mV) 1 0.5 0 -0.5 -100 -120 -140 -1 -1.5 -160 8.83ms/div 0 4k 8k 12k 16k 20k Frequency (Hz) -110dB SIGNAL (10Hz to 20kHz Bandwidth) 200 40 100 20 Output Level (V) Output Level (V) -90dB SIGNAL (10Hz to 20kHz Bandwidth) 0 -100 0 -20 -200 -40 0 400 800 1200 1600 2000 0 Time (s) 800 1200 Time (s) (R) PCM1702 400 4 1600 2000 THEORY OF OPERATION DISCUSSION OF SPECIFICATIONS ADVANCED SIGN MAGNITUDE Digital audio systems have traditionally used laser-trimmed, current-source DACs in order to achieve sufficient accuracy. However, even the best of these suffer from potential lowlevel nonlinearity due to errors at the major carry bipolar zero transition. More recently, DACs employing a different architecture which utilizes noise shaping techniques and very high over-sampling frequencies, have been introduced ("Bitstream", "MASH", or 1-bit DAC). These DACs overcome the low level linearity problem, but only at the expense of signal-to-noise performance, and often to the detriment of channel separation and intermodulation distortion if the succeeding circuitry is not carefully designed. DYNAMIC SPECIFICATIONS Total Harmonic Distortion + Noise The key specifications for the PCM1702 is total harmonic distortion plus noise (THD+N). Digital data words are read into the PCM1702 at eight times the standard compact disk audio sampling frequency of 44.1kHz (352.8kHz) so that a sine wave output of 1002Hz is realized. For production testing, the output of the DAC goes to an I to V converter, then through a 40kHz low pass filter, and then to a programmable gain amplifier to provide gain at lower signal output test levels before being fed into an analog-type distortion analyzer. Figure 1 shows a block diagram of the production THD+N test setup. The PCM1702 is a new solution to the problem. It combines all the advantages of a conventional DAC (excellent full scale performance, high signal-to-noise ratio and ease of use) with superior low-level performance. Two DACs are combined in a complementary arrangement to produce an extremely linear output. The two DACs share a common reference, and a common R-2R ladder for bit current sources by dual balanced current segments to ensure perfect tracking under all conditions. By interleaving the individual bits of each DAC and employing precise laser trimming of resistors, the highly accurate match required between DACs is achieved. This new, complementary linear or advanced sign magnitude approach, which steps away from zero with small steps in both directions, avoids any glitching or "large" linearity errors and provides an absolute current output. The low level performance of the PCM1702 is such that real 20-bit resolution can be realized, especially around the critical bipolar zero point. Table 1 shows the conversion made by the internal logic of the PCM1702 from binary two's complement (BTC). Also, the resulting internal codes to the upper and lower DACs (see front page block diagram) are listed. Notice that only the LSB portions of either internal DAC are changing around bipolar zero. This accounts for the superlative performance of the PCM1702 in this area of operation. For the audio bandwidth, THD+N of the PCM1702 is essentially flat for all frequencies. The typical performance curve, "THD+N vs Frequency", shows four different output signal levels: 0dB, -20dB, -40dB, and -60dB. The test signals are derived from a special compact test disk (the CBS CD-1). It is interesting to note that the -20dB signal falls only about 10dB below the full scale signal instead of the expected 20dB. This is primarily due to the superior low level signal performance of the advanced sign magnitude architecture of the PCM1702. In terms of signal measurement, THD+N is the ratio of DistortionRMS + NoiseRMS/ SignalRMS expressed in dB. For the PCM1702, THD+N is 100% tested at all three specified output levels using the test setup shown in Figure 1. It is significant to note that this test setup does not include any output deglitching circuitry. All specifications are achieved without the use of external deglitchers. Dynamic Range Dynamic range in audio converters is specified as the measure of THD+N at an effective output signal level of -60dB referred to 0dB. Resolution is commonly used as a theoretical measure of dynamic range, but it does not take into account the effects of distortion and noise at low signal levels. The advanced sign magnitude architecture of the PCM1702, with its ideal performance around bipolar zero, provides a more usable dynamic range, even using the strict audio definition, than any previously available D/A converter. ANALOG OUTPUT INPUT CODE (20-bit Binary Two's Complement) LOWER DAC CODE (19-bit Straight Binary) UPPER DAC CODE (19-bit Straight Binary) +Full Scale +Full Scale -1LSB Bipolar Zero +2LSB Bipolar Zero +1LSB Bipolar Zero Bipolar Zero -1LSB Bipolar Zero -2LSB -Full Scale +LSB -Full Scale 011...111 011...110 000...010 000...001 000...000 111...111 111...110 100...001 100...000 111...111+1LSB(1) 111...111+1LSB(1) 111...111+1LSB(1) 111...111+1LSB(1) 111...111+1LSB(1) 111...111 111...110 000...001 000...000 111...111 111...110 000...010 000...001 000...000 000...000 000...000 000...000 000...000 NOTE: (1) The extra weight of 1LSB is added at this point to make the transfer function symmetrical around bipolar zero. TABLE I. Binary Two's Complement to Sign Magnitude Conversion Chart. (R) 5 PCM1702 Use 400Hz High-Pass Filter and 30kHz Low-Pass Filter Meter Settings Distortion Analyzer Programmable Gain Amp 0dB to 60dB Low-Pass Filter 40kHz 3rd Order GIC Type Parallel-to-Serial Conversion DUT (PCM1702) (Shiba Soku Model 725 or Equivalent) Binary Counter Digital Code (EPROM) DATA I to V Converter OPA627 CLOCK LE (Latch Enable) Sampling Rate = 44.1kHz x 8(352.8kHz) Output Frequency = 1002Hz Timing Logic FIGURE 1. Production THD+N Test Setup. Level Linearity Deviation from ideal versus actual signal level is sometimes called "level linearity" in digital audio converter testing. See the "-90dB Signal Spectrum" plot in the Typical Performance Curves section for the power spectrum of a PCM1702 at a -90dB output level. (The "-90dB Signal" plot shows the actual -90dB output of the DAC). The deviation from ideal for PCM1702 at this signal level is typically less than 0.3dB. For the "-110dB Signal" plot in the Typical Performance Curves section, true 20-bit digital code is used to generate a -110dB output signal. This type of performance is possible only with the lownoise, near-theoretical performance around bipolar zero of the PCM1702 advanced sign magnitude. A commonly tested digital audio parameter is the amount of deviation from ideal of a 1kHz signal when its amplitude is decreased form -60dB to -120dB. A digitally dithered input signal is applied to reach effective output levels of -120dB using only the available 16-bit code from a special compact disk test input. See the "16-bit Level Linearity" plot in the Typical Performance Curves section for the results of a PCM1702 tested using this 16-bit dithered fade-to-noise signal. Note the very small deviation from ideal as the signal goes from -60dB to -100dB. Monotonicity Because of the unique advanced sign magnitude architecture of the PCM1702, increasing values of digital input will always result in increasing values of DAC output as the signal moves away from bipolar zero in one-LSB steps (in either direction). The "16-bit Monotonicity" plot in the Typical Performance Curves section was generated using 16-bit digital code from a test compact disk. The test starts with 10 periods of bipolar zero. Next are 10 periods of alternating 1LSBs above and below zero, and then 10 periods of alternating 2LSBs above and below zero, and so on until 10LSBs above and below zero are reached. The signal pattern then begins again at bipolar zero. With PCM1702, the low-noise steps are clearly defined and increase in near-perfect proportion. This performance is achieved without any external adjustments. By contrast, sigma-delta ("Bit-stream", "MASH", or 1-bit DAC) architectures are too noisy to even see the first 3 or 4 bits change (at 16 bits), other than by a change in the noise level. Absolute Linearity Even though absolute integral and differential linearity specs are not given for the PCM1702, the extremely low THD+N performance is typically indicative of 17-bit integral linearity in the DAC. The relationship between THD+N and linearity, however, is not such that an absolute linearity specification for every individual output code can be guaranteed. DC SPECIFICATION Offset, Gain, and Temperature Drift Although the PCM1702 is primarily meant for use in dynamic applications, specifications are also given for more traditional DC parameters such as gain error, bipolar zero offset error, and temperature gain and offset drift. Idle Channel SNR Another appropriate specification for a digital audio converter is idle channel signal-to-noise ratio (idle channel SNR). This is the ratio of noise on the DAC output at bipolar zero in relation to the full scale range of the DAC. To make this measurement, the digital input is continuously fed the code for bipolar zero, while the output of the DAC is bandlimited from 20Hz to 20kHz and an A-weighted filter is applied. The idle channel SNR for the PCM1702 is typically greater than 120dB, making it ideal for low-noise applications. DIGITAL INPUT Timing Considerations The PCM1702 accepts TTL compatible logic input levels. The data format of the PCM1702 is binary two's complement (BTC) with the most significant bit (MSB) being first (R) PCM1702 6 INSTALLATION in the serial input bit stream. Table II describes the exact relationship of input data to voltage output coding. Any number of bits can precede the 20 bits to be loaded, since only the last 20 will be transferred to the parallel DAC register after Latch Enable (Pin6 <PCM1702P>, Pin7 <PCM1702U>, LE) has gone low. All DAC serial input data (Pin1, DATA) bit transfers are triggered on positive clock (Pin2, CLOCK), edges. The serial-to-parallel data transfer to the DAC occurs on the falling edge of Latch Enable. The change in the output of the DAC occurs at a rising edge of the 4th clock of the CLOCK after the falling edge of Latch Enable. Refer to Figure 2 for graphical relationships of these signals. POWER SUPPLIES Refer to CONNECTION DIAGRAM for proper connection of the PCM1702. The PCM1702 only requires a 5V supply. Both positive supplies should be tied together at a single point. Similarly, both negative supplies should be connected together. No real advantage is gained by using separate analog and digital supplies. It is more important that both these supplies be as "clean" as possible to reduce coupling of supply noise to the output. Power supply decoupling capacitors should be used at each supply pin to maximize power supply rejection, as shown in CONNECTION DIAGRAM regardless of how good the supplies are. Both commons should be connected to an analog ground plane as close to the PCM1702 as possible. Maximum Clock Rate A typical clock rate of 16.9MHz for the PCM1702 is derived by multiplying the standard audio sample rate of 44.1kHz by sixteen times (16X over-sampling) the standard audio word bit length of 24 bits (44.1kHz x 16 x 24 = 16.9MHz). Note that this clock rate accommodates a 24-bit word length, even though only 20 bits are actually being used. The setup and hold timing relationships are shown in Figure 3. FILTER CAPACITOR REQUIREMENTS As shown in CONNECTION DIAGRAM, various size decoupling capacitors can be used, with no special tolerances being required. The size of the offset decoupling capacitor is not critical either, with larger values (up to 100F) giving slightly better SNR readings. All capacitors should be as close to the appropriate pins of the PCM1702 as possible to reduce noise pickup from surrounding circuitry. "Stopped Clock" Operation The PCM1702 is normally operated with a continuous clock input signal. If the clock is to be stopped between input data words, the last 20 bits shifted in are not actually shifted from the serial register to the latched parallel DAC register until Latch Enable goes low. Latch Enable must remain low until after the first clock cycle of the next data word to insure proper DAC operation. In any case, the setup and hold times for Data and LE must be observed as shown in Figure 3. DIGITAL INPUT ANALOG OUTPUT CURRENT OUTPUT 1,048,576LSBs 1LSB 7FFFFHEX 00000HEX 80000HEX Full Scale Range NA +Full Scale Bipolar Zero -1LSB -Full Scale 2.40000000mA 2.28882054nA -1.19999771mA 0.00000000mA +1.20000000mA > 40ns Data Input LSB MSB > 15ns > 15ns Clock Input > 20ns > 20ns > 15ns Latch Enable > 15ns > One Clock Cycle TABLE II. Digital Input/Output Relationships. > One Clock Cycle FIGURE 3. Setup and Hold Timing Diagram. Clock DATA "N" Data 1 2 3 4 12 13 14 15 16 17 18 19 20 MSB 1 LSB Latch Enable IOUT N-1 N NOTES : (1) If clock is stopped between input of 20-bit data words, "Latch" Enable (LE) must remain low until after the first clock cycle of the next 20-bit data word stream. (2) Data format is binary two's complement (BTC). Individual data bits are clocked in on the corresponding positive clock edge. (3) Latch Enable (LE) must remain low at least one clock cycle after going negative. (4) Latch Enable (LE) must be high for at least one clock cycle before going negative. (5) IOUT changes on positive going edge of the 4th clock after negative going edge of Latch Enable (LE). FIGURE 2. Timing Diagram. (R) 7 PCM1702 FIGURE 4. Typical Application for Stereo Audio 8X Oversampling system. (R) PCM1702 8 10pF 10pF 1M 16.9344MHz (192FS ) Interleaved Digital Input +5V 4700pF 150 14 100pF DOL 24 1 DA 17 4 WCK 25 28 L/R 15 5 3 BCO 26 14 4 8 10 16 21 Burr-Brown DF1700P DOR 23 2 22 6 Yamaha YM3623 17 8X Interpolation Digital Filter 3 4.7F BCO 12 0.1F + 4.7F +5V A 8 7 + 4.7F 6 28 1 17.1k Digital Interface Format Receiver + 4.7F +5V -5V VCC +5V VCC + C44 3.3F + C42 3.3F + C49 3.3F + C41 3.3F 6 5 4 3 2 1 6 5 4 3 2 1 -5V IOUT -5V +5V BPO DC LE -5V GND +5V BPO DC IOUT PCM1702P BCK +5V DATA LE -5V GND PCM1702P BCK +5V DATA 9 10 11 15 14 13 12 16 9 10 11 15 14 13 12 16 + C48 3.3F + C50 100F + C46 3.3F + C47 3.3F + C49 100F C45 3.3F + + C54 100F + +5V VCC IC3 C56 220p RF2 2.5k -5V VCC IC1 C55 220p RF2 2.5k -5V VCC +5V VCC C52 100F + C54 100F + C51 100F R13 IC3 6.04k IC1 6.04k R12 C60 1000pF R19 5.36k C59 1000pF R18 4.02k R17 4.02k C58 1000pF R16 5.36k C57 1000pF R15 4.02k R14 4.02k R21 IC4 C62 1000pF C61 1000pF VO Low-pass 3-pole Butterworth f-3dB = 40kHz VO Low-pass 3-pole Butterworth f-3dB = 40kHz IC4 IC2 See Application Bulletin AB-026 for information on GIC filters. 2k IC2 2k R20 IC1-4: OPA2604 PACKAGE OPTION ADDENDUM www.ti.com 30-Nov-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) PCM1702P NRND PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type PCM1702P-J NRND PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type PCM1702P-JG4 NRND PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type PCM1702P-K NRND PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type PCM1702P-KG4 NRND PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type PCM1702PG4 NRND PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type PCM1702U NRND SO NS 20 38 Pb-Free (RoHS) CU SNBI Level-2-260C-1 YEAR PCM1702U-2/2K OBSOLETE SO NS 20 TBD Call TI Call TI PCM1702U-2/2KE6 OBSOLETE SO NS 20 TBD Call TI Call TI PCM1702U-J NRND SO NS 20 38 Pb-Free (RoHS) CU SNBI Level-2-260C-1 YEAR PCM1702U-JE6 NRND SO NS 20 38 Pb-Free (RoHS) CU SNBI Level-2-260C-1 YEAR PCM1702U-K NRND SO NS 20 38 Pb-Free (RoHS) CU SNBI Level-2-260C-1 YEAR PCM1702U-KE6 NRND SO NS 20 38 Pb-Free (RoHS) CU SNBI Level-2-260C-1 YEAR PCM1702U/2K NRND SO NS 20 2000 Pb-Free (RoHS) CU SNBI Level-2-260C-1 YEAR PCM1702U/2KE6 NRND SO NS 20 2000 Pb-Free (RoHS) CU SNBI Level-2-260C-1 YEAR PCM1702UE6 NRND SO NS 20 38 Pb-Free (RoHS) CU SNBI Level-2-260C-1 YEAR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 30-Nov-2011 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device PCM1702U/2K Package Package Pins Type Drawing SO NS 20 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2000 330.0 25.4 Pack Materials-Page 1 8.8 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 13.1 2.8 12.0 24.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) PCM1702U/2K SO NS 20 2000 367.0 367.0 45.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated