EGP20A - EGP20DHIGH EFFICIENT RECTIFIERS
PRV : 50 - 200 Volts
Io : 2.0 Amperes
FEATURES :
* High current capability
* High reliability
* Low reverse current
* Low forward voltage drop
* Fast switching for high efficiency
MECHANICAL DATA :
* Case : D2 Molded plastic
* Epoxy : UL94V-O rate flame retardant
* Lead : Axial lead solderable per MIL-STD-202,
Method 208 guaranteed
* Polarity : Color band denotes cathode end
* Mounting position : Any
* Weight : 0.465 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25
°
C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
SYMBOL
EGP
20A
EGP
20B
EGP
20C EGP
20D UNIT
Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 V
Maximum RMS Voltage VRMS 35 70 105 140 V
Maximum DC Blocking Voltage VDC 50 100 150 200 V
Maximum Average Forward Current
0.375"(9.5mm) Lead Length Ta = 55 °C
Peak Forward Surge Current, 8.3ms Single half sine wave
Superimposed on rated load (JEDEC Method)
Maximum Peak Forward Voltage at IF = 2.0 A VF0.95 V
Maximum DC Reverse Current Ta = 25 °CIR5.0 µA
at Rated DC Blocking Voltage Ta = 150 °CIR(H) 50 µA
Maximum Reverse Recovery Time ( Note 1 ) Tj = 25 °CTrr 50 ns
Typical Junction Capacitance ( Note 2 ) CJ70 pf
Junction Temperature Range TJ - 65 to + 150 °C
Storage Temperature Range TSTG - 65 to + 150 °C
Notes :
( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A.
( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC
Page 1 of 2 Rev. 02 : March 25, 2005
A75IFSM
RATING
IF(AV) 2.0 A
D2
1.00 (25.4)
MIN.
0.161 (4.1)
0.154 (3.9)
0.284 (7.2)
0.268 (6.8)
0.034 (0.86)
0.028 (0.71)
1.00 (25.4)
MIN.
Dimensions in inches and ( millimeters )
* Pb / RoHS Free
IATF 0113686
SGS TH07/1033
TH09/2479
TH97/2478
www.eicsemi.com
RATING AND CHARACTERISTIC CURVES ( EGP20A - EGP20D )
FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
+
NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF.
2. Rise time = 10 ns max., Source Impedance = 50 ohms.
3. All Resistors = Non-inductive Types.
FIG.2 - DERATING CURVE FOR OUTPUT FIG.3 - MAXIMUM NON-REPETITIVE PEAK
RECTIFIED CURRENT FORWARD SURGE CURRENT
0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100
AMBIENT TEMPERATURE, ( °C) NUMBER OF CYCLES AT 60Hz
FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
FORWARD VOLTAGE, VOLTS
Page 2 of 2 Rev. 02 : March 25, 2005
RESISTIVE OR INDUCTIVE LOAD
0.375" (9.5mm) LEAD LENGTHS
1.6
1.2
0.8
0.4
2.0
10
1.0
80
0
100
0
60
40
20
0.1
10
80
0.01 0.01
1.0
0.1
100 140020 40 60 120
PERCENT OF RATED REVERSE
VOLTAGE, (%)
PEAK FORWARD SURGE
CURRENT, AMPERES
AVERAGE FORWARD OUTPUT
CURRENT, AMPERES
FORWARD CURRENT, AMPERES
INSTANTANEOUS REVERSE LEAKAGE
CURRENT, MICROAMPERES
TJ = 25 °C
TJ = 100 °C
TJ = 25 °C
Pulse Width = 300 µs
2% Duty Cycle
8.3 ms SINGLE HALF SINE-WAVE
(JEDEC) METHOD
TJ = 55 °C
Trr
+ 0.5
0
- 0.25
- 1.0 A
10ns
OSCILLOSCOPE
( NOTE 1 )
1 Ω
50 Ω10 Ω
D.U.T.
50 Vdc
(approx.)
PULSE
GENERATOR
( NOTE 2 )
50 50
IATF 0113686
SGS TH07/1033
TH09/2479
TH97/2478
www.eicsemi.com
